1
Transducer Switch
Thank You
Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by
esigning and manufacturing top-quality, thoroughly reliable marine equipment. Genuine Humminbird® accessories
d
offer the opportunity to upgrade and expand the capabilities of your Humminbird® product.
Your Humminbird® accessory is designed for trouble-free use in even the harshest marine environment.
In the unlikely event that your Humminbird® accessory does require repairs, we offer an exclusive Service Policy - free
of charge during the first year after purchase, and available at a reasonable rate after the one-year period. For
complete details, see the Warranty section included in this manual.
Contact our Customer Resource Center at 1-800-633-1468 or visit our Web site at humminbird.com.
Installation Overview
Following are instructions for the installation of this accessory. Before you start installation, we encourage you to read
these instructions carefully in order to get the full benefit from your Humminbird® accessory. If you find that any items
are missing from your installation kit, call our Customer Resource Center at 1-800-633-1468 or visit our Web site at
humminbird.com.
The Transducer Switch comes with all the necessary hardware to allow you to connect your control head to two
transducers. The transducers may be the same type of transducer with different mounting locations, or you can
maximize your unit’s performance by using two different transducers. The switch is intended for installation on the
console, and will work well on almost any boat.
531870-1_A
Transducer Switch
Supplies: In addition to the hardware supplied with your Transducer Switch, you will need a hand drill with various
size bits, a Phillips screwdriver, an adjustable wrench, and a 3 amp fuse.
Installation
Perform the procedures in the following sections to install the Transducer Switch on your boat. Before installing the
Transducer Switch, gather all the parts you will need, and make sure that the planned location of the Transducer
Switch will allow you to connect the two transducers to your control head.
1. Locating the Transducer Switch Mounting Position
There are two ways to find the mounting location, as follows:
Switch Panel: If your console already contains a switch panel with an available slot, slide the Transducer Switch into
the designated slot until it snaps into place. Then skip ahead to procedure two.
In-Dash: If your console does not have a switch panel or a pre-made mounting location, you will need to create one
yourself.
Mounting the Switch
Boat Console
Switch
© 2011 Humminbird®, Eufaula AL, USA.
All rights reserved.
2
Transducer Switch
o manually create a mounting location
T
. Locate a suitable, flat area of the dash to mount the Transducer Switch. The switch requires a depth of at least
1
:
1.5 inches (38.1 millimeters). Make sure that it will be positioned near your control head on the console of the
boat, within reach of the cables for both transducers. Also, make sure you have access behind the panel in order
to attach the cables.
2. Tape the template (included) over the desired in-dash mounting location.
3. At a location inside the dotted line on the template, drill a hole large enough to insert the blade of the
reciprocating saw. Carefully begin cutting toward the dotted line, then follow the dotted line around the
template. Remove the template when finished.
4. Insert the end of the switch through the hole until it snaps securely in place.
2. Connecting the Transducers and the Control Head to the Switch
To connect your Transducer Switch to your control head, you may have to remove the control head from the Quick
Disconnect Mounting Bracket and temporarily disassemble the connector holder.
NOTE: Your connector holder hardware may be different than the illustration, depending on your Humminbird® model. See
your control head installation guide for details.
531870-1_A
Inserting the Cable Connector
CAUTION! Do not cut or shorten the transducer cables, and try not to damage the cable insulation. Route the cable as far
as possible from any VHF radio antenna cables or tachometer cables to reduce the possibility of interference. If the cable is
too short, extension cables are available to extend the transducer cable up to a total of 50 feet. For assistance, contact the
Customer Resource Center at humminbird.comor call 1-800-633-1468 for more information.
To connect the transducers to the Transducer Switch:
1. Access your transducer cables and insert each transducer cable connector into a Transducer Switch connector
until you hear it click into place. Refer to the illustration for guidance.
Transducer Switch Configuration
Transducer Switch
Route connector to the unit
Control Head
Connector Holder
Connector Holder
Transducer Switch
Cable Connector
Standard Transducer
Second Transducer
© 2011 Humminbird®, Eufaula AL, USA.
All rights reserved.