Not to be copied, used or translated in part or whole without HUMAX's prior consent in writing except approval
of ownership of copyright and copyright law.
**
Warranty
The information in this document is subject to change without notice. HUMAX does not have any responsibility
for direct, indirect, accidental, necessary and other damage due to your offer or use of the information
contained in this manual.
**
Trademarks
VIACCESS™ is a trademark of France Telecom.
CryptoWorks(TM) is a trademark of Philips Electronics N.V.
Irdeto is a trademark of Mindport BV.
Nagravision is a registered trademark of KUDELSKI S.A.
Conax is a trademark of Telenor Conax AS.
'Dolby' and the double-D symbol are trademarks of Dolby Laboratories.
Manufactured under license from Dolby Laboratories.
**
Thank you for purchasing a HUMAX set top box. Please read this user manual carefully to be able to safely
install, use and maintain the STB at maximum performance. Keep this user manual next to your set top box
for future reference.
GB 1
Page 3
Notice
Read this manual carefully and make sure you understand the provided instructions. For your safety, check
what the result each action will be.
Warnings, Cautions and Notes
Throughout the whole manual, pay special attention to the following marks that indicate hazardous situations.
**
•
Warning
**
Indicates a hazardous situation which, if not avoided, could result in serious injury.
**
•
Caution
**
Indicates a situation which, if not avoided, could damage the equipment or other apparatus.
**
•
Note
**
Indicates additional information to the user to make the user aware of possible problems and information
of any importance to help the user to understand, to use and to maintain the installation.
**
**
To reduce the risk of electric shock, do not remove cover (or back). No user
serviceable parts inside. Refer servicing to qualified service personnel.
**
This symbol indicates dangerous voltage inside the product that presents a risk
of electric shock or personal injury.
**
This symbol indicates important instructions accompanying the product.
**
GB 2
Page 4
Safety and Warning
This digital set top box has been manufactured to comply with international safety standards. Please read the
following safety precautions carefully.
**
Safety Instructions and Precautions
**
1. MAINS SUPPLY
**
190 - 250V AC 50/60Hz
Operate your product only from the type of power supply indicated on the marking label. If you are not
sure of the type of power supplied to your home, consult your local power company. Disconnect the STB
from the mains before you start any maintenance or installation procedures.
**
2. OVERLOADING
**
Do not overload a wall outlet, extension cord or adapter as this may result in electric fire or shock.
**
3. LIQUIDS
**
The STB should not be exposed to any liquids such as dripping or splashing. In addition, no objects filled
with liquids, such as vase, should be placed on the apparatus.
**
4. CLEANING
**
Disconnect the STB from the wall outlet before cleaning. Use a light damp cloth (no solvents) to dust the
STB.
**
5. VENTILATION
**
The slots on top of the STB must be left uncovered to allow proper airflow to the unit. Do not stand the
STB on soft furnishings or carpets. Do not stack electronic equipment on top of the STB.
**
6. ATTACHMENTS
**
Do not use any unsupported attachments as these may be hazardous or cause damage to the STB.
**
7. CONNECTION TO THE SATELLITE DISH LNB
**
Disconnect the STB from the mains before connecting or disconnecting the cable from the satellite dish.
Failure to do so can damage the LNB.
**
8. CONNECTION TO THE TV
**
Disconnect the STB from the mains before connecting or disconnecting the cable from the satellite dish.
Failure to do so can damage the TV.
**
9. EARTHING
**
The LNB cable must be buried in the ground. The buried cable of the system must comply with SABS
061.
GB 3
Page 5
Safety and Warning
10.LOCATION
**
Place the STB indoors to avoid exposing it to lightning, rain or sun.
Do not place it near a radiator or heat register.
Make sure it has more than 10 cm clearance from any appliances susceptible to electromagnetic
influences, such as a TV or a VCR.
Do not block these openings with any object, and do not place the product on a bed, sofa, rug, or other
similar surface.
If you place the product on a rack or bookcase, ensure that there is adequate ventilation and that you
have followed the manufacturer's instructions for mounting.
Do not place the product on an unstable cart, stand, tripod, bracket, or table where it can fall. A falling
product can cause serious injury to a child or adult, and serious damage to the appliance.
**
11.LIGHTNING, STORM, or NOT IN USE
**
Unplug the product from the wall outlet and disconnect the antenna during a thunderstorm or when left
unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and
power-surges.
**
12.EXTRANEOUS OBJECTS
**
Do not insert anything through the openings in the unit, where they can touch dangerous voltage points
or damage parts.
**
13.REPLACEMENT of PARTS
**
When the replacement parts are required, be sure the service technician uses replacement parts
specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in additional damage to the unit.
**
Warning
**
1. Follow these directions in order not to damage the power cord or plug.
Do not modify or process the power cord or plug arbitrarily.
Do not bend or twist the power cord too much.
Make sure to disconnect the power cord with the plug held.
Keep heating appliances as far as possible from the power cord in order to prevent the cover vinyl from
melting.
**
2. Follow these directions. Failure to follow one of them may cause electrical shock.
Do not open the main body.
Do not insert metals or inflammable objects inside the product.
Do not touch the power plug with wet hands.
Disconnect the power cord in case of lightning.
**
3. Do not use the product when it is out of order. If you continue to use the product when defective, a
serious damage can be caused to it. Make sure to contact your local product distributor if the product is
out of order.
**
4. Please do not insert metal or alien substance into the slots for the modules and smart cards. In doing so
can cause damage to the STB and reduce its life span.
GB 4
Page 6
Reference
1. Connect DiSEqC 1.0
All our STBs are designed to be DiSEqC 1.0 compatible. This allows multiple antennas to be connected to the
STB simultaneously.
If you have two or more fixed antennas or LNBs, you can use a DiSEqC 1.0 switch.
1. Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC
switch.
2. Connect the coaxial cable from the second LNB to the LNB 2 or LNB B input connector of the DiSEqC
switch.
3. Do the same for other LNBs.
4. Connect one end of a Coaxial cable to the RF output connector of the DiSEqC switch and the other end
to the LNB IN socket on the STB.
**
2. Connect DiSEqC 1.2
Please refer to Motorised System.
The Locking Time might take longer than expected during the initial boot if the motorised system is set
“enable” mode.
**
3. Connect a Satellite antenna
To the digital set top box, you can connect either a single satellite antenna directly or through converter box
several antennas or LNB of multi-feed equipment.
You can connect a further Sat-STB (for example analogue), with the STB of common antenna equipment that
has satellite signals.
**
Connect an antenna cable through converter boxes
**
1. When you assemble several antenna or a multi-feed equipment that has several LNB (or LNB with
several exits), connect each cable from the antenna to a converter box.
2. Connect the output of converter box to “LNB IN”, as in example displayed.
3. When you use a converter box of 0/12V-steerage, connect it to the output “0/12V” additionally.
For converter boxes of 22KHz- or DiSEqC-steerage, you can skip this point because the steerage signal
occurs through the antenna cable.
**
4. Loop Through
If you have another analogue or digital STB and you wish to use the same LNB then you can connect it via the
loop through. Connect one end of a Coaxial cable to the LNB OUT on the STB and connect the other end to
the LNB IN on your second STB.
GB 5
Page 7
Reference
5. Connect a S/PDIF Fiber-Optic cable
If you are watching a programme with a Dolby Digital soundtrack(see page GB14) you can enjoy the higher
quality sound of the Dolby Digital audio by connecting the STB to an external Dolby Digital television or
amplifier. Do this by connecting the optical S/PDIF output of the STB to the optical S/PDIF input of the external
Dolby Digital product (television, amplifier,.....).
**
6. Software Upgrade
HUMAX digital set-top box is a highly sophisticated product - incorporating one of the best software
applications.
Whenever a problem is found with this software or, in fact, extra functions or enhanced applications are
added, the software in the equipment has to be upgraded.
In order to maintain proper performance of the product, it is essential to have the most up to date software.
The latest news and release of software versions may be found at HUMAX website -
http://www.humaxdigital.com.
It is recommended that users register to HCSA(HUMAX Customer Service Area) and periodically check for the
availability of software upgrade.
**
There are three methods to upgrade the software:
a. set-top box to set-top box download(copies the software of the main unit into slave unit);
b. pc to set-top box download(downloads the software directly from pc to the model requiring upgrade);
c. OTA over-the-air(downloads the software where the manufacturer reserves the right to decide when and
where to release through satellite system).
**
Over The Air(OTA) is simply another alternative for downloading software versions.
However, the manufacturer reserves the right to decide when and where this software upgrade can take place
by "beaming" latest software versions over the air via satellite systems. Note that OTA is only limited to certain
geographical regions mainly due to different satellites having different footprints(area where the signal can be
received).
**
SUSS(TM) is an official trademark and logo for HUMAX loader software to perform OTA.
The software upgrade via satellite system will only occur under the following circumstances:
(1) the equipment should have appropriate loader software;
(2) the manufacturer decides to release software downloading via a designated satellite system;
(3) the equipment must be "tuned" properly to the same satellite that the manufacturer uses.
**
Note : CRCI-5500+ complies with the OTA type of CryptoWorks.
GB 6
Page 8
Contents
1. Before using the STB
1.1 Front Panel
1.2 Rear Panel
1.3 Remote Controller
2. Setup
2.1 Connecting to TV, VCR and Hi-Fi System
2.2 TV with VCR and Motorised System (DiSEqC 1.2)
2.3 Powering On
2.4 Selecting a Language
3. Basic Operation
3.1 Information Box (I-Plate)
3.2 Changing Services
3.3 Volume Control
3.4 Soundtrack
3.5 Subtitle
3.6 Teletext
3.7 Motion Still
3.8 Changing Display Format
3.9 Using the Help
4. Guide of Main Menu
4.1 Select Service
4.2 TV Guide
4.3 Parental Control
4.4 Installation
4.5 Utility
**
**
**
**
GB8
GB8
GB9
GB10
GB12
GB12
GB13
GB14
GB14
GB15
GB15
GB16
GB16
GB16
GB17
GB17
GB17
GB18
GB18
GB19
GB20
GB23
GB25
GB25
GB41
5. Motorised SystemGB42
6. Troubleshooting GuideGB48
7. Menu MapGB50
8. SpecificationGB51
9. GlossaryGB53
GB 7
Page 9
Page 10
1. Before using the STB
1.2 Rear Panel
**
**
1. LNB IN
Use to connect an antenna.
**
2. LNB OUT
Use it when connecting to another STB.
**
3. RS-232C
Use it when connecting to your PC.
**
4. TV SCART
For the audio/video input of the TV.
**
5. VCR SCART
For the VCR.
**
6. AUDIO/VIDEO OUTPUT
Audio/video signal from your STB to VCR or TV.
**
7. 0/12V OUT
For an external LNB switch.
**
8. RF OUTPUT
Use to connect a RF signal from your STB to RF(ANT) input jack on your TV.
**
9. RF INPUT
Use to connect a general Aerial Antenna and CABLE jacks to a RF input jack on the STB.
**
10.S/PDIF
Output for connection to a digital amplifier.
GB 9
Page 11
1. Before using the STB
1.3 Remote Controller
GB 10
Page 12
1. Before using the STB
1. SOURCE
Selects the input source between TV
and satellite STB.
**
2. TV/RADIO
Switches between TV and Radio
modes.
**
3. NUMERICAL BUTTONS
Enter a TV/Radio service number or
menu option number.
**
4. MENU
Displays the main menu.
**
5. TIME - WHITE
Displays the current time on the
screen. Reserves services on the
i-plate or EPG.
**
6. ARROW BUTTONS
Change the service or move the cursor
to the up, down, left or right menu
option.
**
7. i (INFORMATION) - RED
Displays the information about the
service and programme.
**
8. SOUNDTRACK - GREEN
Displays the Soundtrack.
**
9. CH- / CH+
Changes the Service.
**
10.RECALL
Returns to the previous screen.
**
11.FREEZE
Freezes the TV screen you are
watching. Play the audio continuously.
**
12.WIDE
Changes the Display Format.
**
13.STANDBY
Switches between Operation and
Standby modes.
**
14.GUIDE
Displays the Programme Guide.
**
15.EXIT
Returns to the previous menu and
exits the guide screen.
**
16.OK
Selects a menu or confirms the
selected operation. Displays the
service list during watching a
programme.
**
17.ZOOM - BLUE
Enlarges the picture.
(Reserved for future use)
**
18.SUBTITLE - YELLOW
Changes the subtitle language.
**
19.V- / V+
Adjusts the audio volume.
**
20.MUTE
Pauses the audio temporarily. That is,
volumes on/off temporarily.
**
21.UHF
Displays the UHF menu.
**
22.? (HELP)
Displays the Help box on the screen.
**
*COLOUR BUTTONS (R/G/B/Y/W)
Select the corresponding colour option
shown on the screen.
GB 11
Page 13
2. Setup
2.1 Connecting to TV, VCR and Hi-Fi System
There are several ways of connecting the STB to your existing Audio/TV system.
We recommend using one of the following set-up for best results:
**
**
TV only
1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to
a SCART socket on your TV.
2. Connect one end of a RF lead to the RF OUT connector on the STB and the other end to the RF IN
connector on your TV.
3. Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels.
4. Connect the coaxial cable from the LNB to the LNB IN socket on the STB.
**
TV with VCR
1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to
a SCART socket on your TV.
2. Connect one end of a 21-pin SCART cable to the VCR SCART connector on the STB and the other end
to a SCART socket on your VCR.
3. Connect one end of a RF lead to the RF OUT connector on the STB and the other end to the RF IN
connector on your VCR.
4. Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the RF IN
connector on your TV.
5. Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels.
6. Connect the coaxial cable from the LNB to the LNB IN socket on the STB.
GB 12
Page 14
2. Setup
With Hi-Fi System
1. Connect an RCA/Cinch stereo cable from the AUDIO L, R sockets on the back of the STB to the LINE,
AUX, SPARE OR EXTRA input sockets on your Hi-Fi system.
**
2.2 TV with VCR and Motorised System (DiSEqC 1.2)
**
**
1. Connect one end of a 21-pin SCART cable to the TV SCART connector on the STB and the other end to
a SCART socket on your TV.
2. Connect one end of a 21-pin SCART cable to the VCR SCART connector on the STB and the other end
to a SCART socket on your VCR.
3. Connect one end of a RF lead to the RF OUT connector on your VCR and the other end to the RF IN
connector on your TV.
4. Connect one end of a RF lead to the RF IN connector on your VCR and the other end to the RF OUT
connector on the STB.
5. Connect the coaxial cable from the LNB of your motorised system to the LNB IN socket on the STB.
6. Connect your TV antenna to the RF IN connector on the STB for receiving terrestrial channels.
GB 13
Page 15
2. Setup
2.3 Powering On
1. Connect the power cord of the STB to a wall outlet.
**
2. Turn on the power switch, located at the left of the back of the STB. Make sure that the Standby LED
indicator is turned on Red.
**
**
3. Press the STANDBYbutton on the Remote Controller or the front of the STB. The Standby LED
indicator is turned off.
**
2.4 Selecting a Language
You can select the language before you use the STB. Select your desired
language using the
**
Note: The following procedure displays the Antenna setting screen.
For detailed information about setting the antenna, refer to 4-3
Service Searching.
GB 14
button and press the OKbutton.
Page 16
3. Basic Operation
3.1 Information Box (I-Plate)
Information box is always displayed for a specific period of time whenever you switch services. You can view
the i-plate by pressing the i
I-plate.
**
1. Service number and service name
2. Programme name
3. Icons
Represents parental level.
Displayed only if this programme is reserved.
Displayed only when the service is a locked service.
Displayed only when subtitle information is available.
Displayed only when the service is a scrambled service.
Displayed only when there is any teletext information.
Displayed only when the programme is a dolby digital one.
**
4. Current time
5. Programme time
6. Next programme Information : displayed if next programme information is provided. Press the
to display the next programme information.
7. Signal Strength and Quality Bar.
Note: If there is no available programme information, programme information is not displayed.
**
You can see detailed information by pressing the ibutton again where
i-plate is displayed.
You can reserve the programme by pressing the WHITE
i-plate is displayed.
button while watching a programme. Press the EXITbutton to hide the
button
button where
GB 15
Page 17
3. Basic Operation
3.2 Changing Services
You can change services using the one of the following ways.
1. Press the CH-/CH+
2. Enter your desired service number using the NUMERICAL (0~9) buttons to move to the service directly.
3. Press the RECALL
4. Press the TV/RADIO
5. Press the OK
6. Press the GUIDE
button to display the service list.
**
3.3 Volume Control
To adjust the volume level, use the V-/V+buttons orbuttons.
To temporarily stop the volume, press the MUTE
mute, press the MUTE
or
buttons.
**
**
orbuttons.
button to return to the previous service.
button to switch between TV and Radio services.
button to display the programme guide list.
button. To cancel
button again or press the V-/V+buttons
3.4 Soundtrack
When you want to change the audio language of current service, press
the SOUNDTRACK
The on-screen menu is displayed on the top to left side of the screen.
GB 16
button firstly.
Page 18
3. Basic Operation
To change the audio language:
1.
2.
3. OK
**
When the current service is switched, the audio language returns to the audio language that was selected in
previous service. lf the returned audio language is invalid, the audio language that you selected from the audio
language menu has the priority of playback.
Soundtracks broadcast in Dolby Digital are indicated by Dolby Digital symbols either side of the respective
language selection in the menu. By selecting such a soundtrack the Dolby Digital audio will be output by the
optical S/PDIF on the STB.
This can be decoded by an external Dolby Digital television or amplifier, for example.
**
3.5 Subtitle
When the current broadcasting programme provides subtitle, press the
SUBTITLE
**
To change the subtitle language:
1. Use thebuttons to select a Subtitle language you want.
2. Press the OK
**
buttons : Use to select the audio on the left, right or both.
buttons : Use to select the audio language you want.
, EXITbutton : When this button is pressed, the Soundtrack OSD will disappear keeping the
selected Soundtrack language constant.
button to see the current subtitle language list.
button and the selected language is highlighted
and then the Subtitle Language you want is displayed on the
screen.
Press the EXIT
button to cancel the Subtitle mode.
3.6 Teletext
Use your TV Remote Control Unit to control the Teletext service. The teletext button doesn’t exist on the STB
Remote Control Unit. When the service supports Teletext, the Teletext icon
is displayed on the I-plate.
**
3.7 Motion Still
Press the FREEZEbutton to pause the current programme.
Press the FREEZE
button again to continue the programme.
GB 17
Page 19
3. Basic Operation
3.8 Changing Display Format
Press the WIDEbutton to select display format.
You can select one among “Auto, Letter Box, Centre” if screen mode is set to 4:3.
You can select one among “Auto, Full, Pillar Box” if screen mode is set to 4:3.
**
3.9 Using the Help
When you press the HELPbutton in normal viewing, the Help window
will appear on the screen. The Help window shows the current Network
information, including: Satellite Name, Frequency, Polarisation, Symbol
Rate, FEC...
When you press the HELP
Help window describes what the button or function does and how to use
it.
button with On-screen Display (OSD),
GB 18
Page 20
4. Guide of Main Menu
4.1 Select Service
The select service displays the required service list which can be viewed
in Simple or Advanced mode.
4.2 TV Guide
Your STB has an Electronic Programme Guide(EPG) to help you navigate through all the possible viewing
options.
The TV Guide supplies information such as programme listings and start and end times for all available
services.
In addition, detailed information about the programme is often available in the EPG (the availability and
amount of these programme details will vary, depending on the particular broadcaster).
**
4.3 Parental Control
Access to services and programmes is controlled by a PIN code (i.e., a 4-digit secret code that is defined by
the user).
The very first time you attempt to lock all services(or lock programmes by ratings), the on-screen menu will
instruct you to assign a PIN code(Later on, if necessary, you can change it).
**
4.4 Installation
The Installation mode allows you to have the information of setting services and newly set services (language,
time, organise, search,..). Furthermore, you can recognize the states of hardware and software versions and
signals from your STB.
**
4.5 Utility
This menu provides Calendar and Biorhythm.
GB 19
Page 21
4. Guide of Main Menu
4.1 Select Service
To select the desired service in the service list, you should firstly display the service list using the OK
button. Use thebuttons to select a service and press the OKbutton. Also use the CH-/CH+
buttons to select a service directly in the service list.
The contents of service list are as follows:
**
Simple Service List
1. Use thebuttons to select “Select Service” from the Main Menu
and press the OK
2. Use the
buttons to select “Simple” from the Main Menu and
press the OK
3. Then the simple service list will appear on the screen.
**
Advanced Service List
The advanced service list shows twenty services. This list is similar to the
Simple service list except that it shows twenty services. The full name of
the service on the current cursor is displayed on the bottom of screen.
For Scrambled Service, an icon
**
Use the following colour buttons to list various service lists:
**
button.
button.
appears on the right service.
The colour button corresponds the following Service List.
•REDbutton - service list All
•GREEN
•YELLOW
•BLUE
•WHITE
GB 20
button - Favourite
button - Network
button - Satellite
button - service list by Alphabetical order
Page 22
4. Guide of Main Menu
1. Service Configuration
To change the attributes of a service
1. Use the
the Service List.
2. Press the MENU
3. Use the
skip, delete) you want on the Service Configuration screen.
4. Use the
Press the OK
**
2. Service All
1. To display the Service All, press the OKbutton Use the RED
button to select the All service list.
2. Select the desired service by using the
3. Press the OK
The service list provides you the Simple mode and Advanced mode.
The right side scroll-bar of the screen displays the location of the
selected service in relation to All services.
Press the RED
Advanced mode.
**
buttons to move a service you want to change in
button.
buttons to move to an item (such as favourite, lock,
buttons to select.
button to complete.
buttons.
button to view the selected service.
button to toggle between Simple mode and
3. Service Favourite
1. Press the GREENbutton on the remote control unit to select the
Favourite service list.
Note: The groups are labeled in four different alphabet characters
(A, B, C, D).
2. Use the
3. Press the GREEN
buttons to select a favourite group that you want.
button to toggle group and service list.
GB 21
Page 23
4. Guide of Main Menu
4. Service Network
1. Press the YELLOWbutton on the remote control unit to select
the Network service list.
2. Use the
3. Press the YELLOWNote:1.The provider name is displayed on the left window
2.The scroll bar on left of the screen shows the location
**
5. Service Satellite
1. Press the BLUEbutton on the remote control unit to select the
Satellite service list.
2. Use the
3. Press the BLUENote: The scroll bar on left of the screen shows the location of the
cursor in the Satellite. The scroll bar on right side of the
screen shows the location of the selected Satellite service.
**
buttons to select a service.
button to toggle provider and service list.
and the provider’s services are displayed on the right
window.
of the cursor in the Network. The scroll bar on right of
the screen shows the location of the service from the
selected Network.
buttons to select a service.
button to toggle Satellite and service list.
6. Service Alphabet Order
1. Press the WHITEbutton on the remote control unit to select the
Alphabet service list.
2. Use the
3. Press the WHITENote: The scroll bar on left of the screen shows the location of the
cursor in the Alphabet. The scroll bar on right side of the
screen shows the location of the selected Alphabet service.
GB 22
buttons to select a service.
button to toggle Alphabet and service list.
Page 24
4. Guide of Main Menu
4.2 TV Guide
You can watch a programme being shown and reserve it in the TV Guide mode.
**
To enter the TV Guide mode
Press the GUIDE
**
To select the TV/Radio Guide
Press the TV/RADIO
**
TV Guide mode includes four different modes.
To select each mode, use the following buttons:
•RED
•GREEN
•YELLOW
•BLUE
1. Now/Next mode
Show the informations of the programmes that are played now or will be
played next time.
This mode consists of the service name, programme name, programme
duration time, current time and on-screen-display window.
**
To watch a programme you want through the display window:
•Use the CH-/CH+buttons to select a programme you want.
The selected service will appear on the right display window.
**
•Use thebuttons to select a programme you want. And then press the OKbutton on the remote
control unit. The selected service will appear on the right display window. The selected OSD will be
highlighted every time the cursor moves.
**
To reserve a programme you want:
•Select a programme you want by using the CH-/CH+buttons orbuttons. And then press the
WHITE
Press the
the YELLOW
button on the remote control unit or select the TV Guide on the Main Menu.
button on the remote control unit and TV Guide will be switched to the Radio Guide.
button : Use to display the current and next programme list.
button : Use to display the programme list for one-week.
button : Use to display the reserved programme list.
button : Use to display the simple TV Guide list. (Quick mode)
button.
buttons to watch the programme of previous page or the programme of next page. Press
button to watch the Reserved programme list.
GB 23
Page 25
4. Guide of Main Menu
2. Weekly mode
Shows the information of programmes that will be played for a week.
**
To watch a programme you want through the display window:
•Press the OKbutton and then press thebuttons to select a
programme you want. Press the OK
**
To reserve or cancel programme reservation:
•Select a day you want using thebuttons.
Press the
press the WHITE
buttons to select a programme you want and then
button.
3. Reserved mode
Shows the programme lists that you have already reserved on the TV
Guide or Information box.
Maximum eight programmes can be reserved. This programme list
includes service name, date, duration time, reservation mode and
programme name.
To cancel the Reserved service, select a programme you want to cancel
using the
buttons and then press the WHITEbutton.
button again.
4. Quick mode
Shows a simple TV Guide like an Information box.
This mode shows in the A/V playback mode.
•Red vertical line : Indicates the current time.
•Black/white bar : Shows the proceeding state of programme.
•Time range of bar : This consists of three blocks by 30 minutes per
block.
GB 24
Page 26
4. Guide of Main Menu
4.3 Parental Control
You can set a parental guidance rating to each programme in this mode.
1. When the OK
parental control on the initial menu screen, a display window for
entering the PIN code will appear on the centre of screen.
** The default PIN code is 0000.
2. Enter the PIN code on the display window. (If any problem occurs
when entering a PIN code, you cannot switch to the next mode.)
3. Set the parental guidance rating of highlighted censorship
classification.
The parental level is given as age-based numbers :
no block, 6, 10, 14, 18 and total block.
Note: You have to enter PIN code to watch the progamme which is
blocked by the age level.
4. To change your PIN code:
•Select the highlighted Old PIN code using the
then enter your Old PIN code.
•Enter a New PIN code in the highlighted New PIN code using the
buttons.
•To verify the New PIN code, re-enter a New PIN code in the
highlighted Verify Changed PIN code.
5. When the entered PIN code is correct, then all settings are completed.
(If the PIN code is wrong, the message “PIN code mismatch” will be displayed on the display window.
When the OK
first position of this menu.)
button is pressed after selecting the highlighted
**
buttons and
button is pressed at this time, the Old PIN code is valid and the cursor is located in the
GB 25
Page 27
4. Guide of Main Menu
4.4 Installation
This mode allows you to customise, add a new service and displays the
state of the STB. Enter the submenus after selecting the Installation mode
in the Main Menu.
1. System Setting
The System Setting mode supports the STB internal settings according to the connection of the STB and
external units. This mode includes Language Setting, Time Setting, A/V Output Setting, UHF Tuning and
Other Settings.
Language Setting
Select the language for menu, audio or subtitle.
1. Select the highlighted language setting using thebuttons in the
system setting mode and then press the OK
2. Select the highlighted Menu(or Audio, Subtitle) Language and press
the
3. Use the
press the OK
**
buttons and the language list will be displayed.
buttons to move to a language you want and then
button to finish setting.
button.
Menu Language
Select the default language for On-Screen-Display (OSD).
**
The kind of languages can be changed depending on the country.
Languages are subject to change without prior notice.
Audio Language
Select the default language for audio when changing services. If you change the current service, your STB will
initially select the previously memorised Audio Language. If the Audio Language of current service is not
provided, at this time, you should reselect a language on the Audio Language menu.
Subtitle Language
Select the default language for subtitle when changing services.
**
GB 26
Page 28
4. Guide of Main Menu
Time Setting
You can set the Current Time and Wakeup Time in this mode.
Furthermore, the Service Number in the Wakeup mode and Sleep
Time(standby mode) can be set. When a VCR is connected, recording
can be automatically done according to Wakeup/Sleep Time Setting.
Current Time
To set the Current Time, enter the Offset value using the standardised
information of current service area.
The time setting will be used as the standardised time for the I-Plate, TV
Guide, Wakeup and Sleep Timer.
Time Offset
Current Time is based on TDT(Time and Data Table) at the stream of the current service.
Wakeup Time
Select the time when STB is turned on.
Use the NUMERICAL (0~9) buttons on the remote control unit to enter your Wakeup Time.
Wakeup Service No.
Use thebuttons to set the service number provided for the set Wakeup Time.
Use the TV/RADIO
button on the remote control unit to toggle TV/Radio service.
Sleep Time
Select the time when STB is turned off.
**
A/V Output Setting
Audio Output
Set the audio mode which is output from the TV SCART and RCA/Cinch
Jack. (Stereo/Mono)
Dolby Digital
lf Dolby Digital option is ON and the broadcaster provides the Dolby
Digital stream, the Dolby Digital audio language is firstly selected when
changing the service.
Screen Mode
Select the aspect ratio of TV which is connected to STB(4:3 or 16:9).
Display Format
Select the format which the video is to be displayed on screen.
When your TV set is 4:3 and video source is 16:9, STB will display in Letter-box or Centre mode as selected.
When your TV set is 16:9 and video source is 4:3, STB will display in the Pillar-box or Full mode as selected.
GB 27
Page 29
4. Guide of Main Menu
NTSC Mode
Adjust this value between 3.58 and 4.43 if your TV displays the video only in black and white color. Normally
NTSC 3.58 mode is used worldwide, but some TV sets can support only NTSC 4.43 mode.
UHF Tuning
You select the STB output by using the UHF channel.
Channel
Select an UHF channel. The range of channels and frequency value are
different for each PAL Standard:
PAL I/G for Europe
PAL B for Europe/Australia
PAL D for China
PAL K for Russia
PAL Standard
Select a PAL Standard according to the above range of channels.
Offset
Adjust the fine tuning value. The Offset ranges from -4 to +4 and each Offset represents 1MHz.
**
Other Setting
Select the OSD Transparency, Information Box Display Time and so on.
Select the OSD Transparent type. It affects Information box, Soundtrack,
Subtitle, Service list, Time and Quick mode of TV Guide. Use the
buttons to toggle transparent, opaque, 25%, 50%, and 75%.
Info. Box Display Time
Set the display duration of Information box displayed on the screen after
changing services. The time ranges from 0 to 20 seconds.
Changing to Reserved Service
When the reserved time has come during the view of services:
**
•Manual Mode
This mode shows the message “A reserved event has started on another service. Press OK to view the
reserved service. Press EXIT to ignore reserved service. (will automatically change after 10 seconds.)”
And ask the presence of change and then makes a change.
**
•Auto Mode
The current service will be automatically changed to the time-reserved service.
GB 28
Page 30
4. Guide of Main Menu
2. Service Organising
This menu gives users access to options that allow them to organise their
TV Services, Radio Services and Networks.
** The default PIN code is 0000.
Organise TV Services
Organise All Services
This mode allows users to Delete, Move, Lock, Skip and Rename TV
Services.
**
•Delete
**
1. Press the REDbutton to delete unwanted services.
2. Highlight the services that you want to delete in grey.
3. Press the OK
**
•Move
**
button to confirm.
1. Press the GREENbutton to move the service to where you
want to locate. Then, the icon
will be displayed in front of the
service number.
2. Use the
3. Press the OK
**
•Lock
**
buttons to select a new location.
button to fix the location.
1. Press the YELLOWbutton to lock services.
Then, the symbol “
” will be displayed at the right side of the service name.
2. Enter the PIN code to view the locked services.
**
•Skip
**
1. Press the BLUEbutton to skip services.
Then, the symbol “
” will be displayed at the right side of the service name.
2. Use the NUMERICAL (0~9) buttons, service list or the GUIDE
when selecting channels.
Note: You can’t view the skipped services by using the CH-/CH+
**
•Rename
**
1. Press the WHITEbutton to change the service name. Then, the keyboard image will be displayed
on the screen.
2. Key in the new service name.
**
button to view the skipped services
buttons.
GB 29
Page 31
4. Guide of Main Menu
You can use the four direction keys to move or select the services.
**
: to move the previous service
: to move the next service
: to move back by services
: to move forwards by services
**
Note: The box between service list and the description of the colour buttons offers the brief information of a
service where the cursor is located.
**
Organise Favourite A~D
Each of TV and Radio has four Favourite groups. Each Favourite group
contains up to 100 services.
Delete, Move, Lock, Skip or Rename each TV service in a Favourite TV
group and re-group them into your Favourite TV group. This mode has
the same operating methods as “organise all services”.
**
•When you delete a service in the Favourite group, it will be available
again on the All TV service list. This allows the service to be
removed from the Favourite group.
•You can move the service only within the Favourite group.
•Coloured keys are available when the cursor is located in the middle window. (Except when the middle
window is disabled(grey).)
**
To select the Favourite group;
1. Use thebutton to move the cursor to “Gr.”-plate(left).
2. Select the wanted favourite group.
**
To group the services into Favourites;
1. Use thebutton to move the cursor to “services”-plate (right).
2. Select the service you want to group into Favourites.
3. Press the OK
4. Use the
5. Press the OKNote: 1. Use the
2. Use the CH-/CH+
button.
button to move the cursor to “Favourites”-plate(left).
button to save the selected group.
buttons to move the cursor.
buttons to select the previous or next page.
GB 30
Page 32
4. Guide of Main Menu
Organise Radio Services
The Organise Radio Services functions same as TV Services except that
it uses Radio Services.
You can delete or move Radio Services and change the attributes of
them.
Organise All Services
The Organise All Services lets the user Delete, Move, Lock, Skip or
Rename Radio services on the All Radio services list.
Organise Favourite A~D
The Organise Favourite A~D lets the user Delete, Move, Lock, Skip or
Rename Radio Services from the Favourite Radio Services and group
into a new Favourite Radio Services.
The Radio Services are grouped into a Favourite in the same way as the
TV Services.
**
**
Organise Networks
You can edit services using the network unit.
•The provider names are displayed on the left side of screen, and the
TV/Radio Services included in the highlighted Network are
displayed on the right side of screen.
Only the Delete, Move, Rename Function can be used in this mode.
•When TV/Radio Services are too many to be displayed, use the
button to move the cursor to the right window and use theand
CH-/CH+
buttons to move the cursor to the next list.
GB 31
Page 33
4. Guide of Main Menu
In Radio Service iconis marked in front of service number.
Delete Satellites
1. Press thebuttons to move to the satellite, Tp, or ALL you
want to delete.
2. Press the RED
3. Press the OK
3. Service Searching
Enter the PIN code to access the Service Searching menu as you access
the Parental Control or Service Organising menu. Press the OK
button to start Service Search after setting the parameters.
** The default PIN code is 0000.
Antenna Setting
Selects the antenna and LNB settings for Service search.
As you can change the settings for 22KHz Tone, 0/12V and DiSEqC switch, there are 32 possible Antenna
Setting for use.
The values that are set in this menu will be available for selection in other service searching menus.
**
button to select the item you want to delete.
button to delete.
Antenna Alternative
There are 32 antenna alternatives, each one can have different
combinations of settings for 22KHz Tone, 0/12V and DiSEqC switch.
Antenna Alternative 16 is predefined for SMATV. Satellite Master Antenna
Television (SMATV) is used to deliver signals to multiple dwelling units
(e.g., apartment buildings and hotels).
GB 32
Page 34
4. Guide of Main Menu
Satellite Name
Selects the Satellite Name that corresponds to the value of the Antenna
Alternative.
1. Press the
2. Select the wanted Satellite Name.
3. If the desired Satellite Name is not listed then select User Defined.
4. The keyboard will appear and you can type the Satellite Name
directly.
The selected Satellite Name can help you select the Antenna Alternative in the searching menu, but it is
possible to change or select the Satellite Name only in the Antenna Setting menu.
Note: In case the selected satellite is used as OTA target satellite, automatic detection of the OTA target
satellite might not work properly if you change or edit the name of the satellite.
5. Satellite Name is listed in alphabetical order and the order can be changed according to Menu
Language.
**
LNB Frequency
1. Select the L.O. (Local Oscillator) Frequency that is set to antenna.
2. Use the
9750, 10600, 10750, 11475MHz or 0, 1, ......., 9).
3. If the required LNB Frequency is not available, then select “0” and
enter the frequency manually using the NUMERICAL (0~9) buttons.
4. When you select Universal, both 9750 and 10600MHz are
supported at the same time.
The 22KHz Tone setting is unnecessary. (Disabled)
buttons to display the satellite list box.
buttons to select the LNB frequency(Universal, 5150,
22KHz Tone
When you use a dual LNB or two antennas connected to a 22KHz Tone switch box, make 22KHz Tone switch
enable or disable to select LNB or antenna.
0/12Volt Switch
When you use two LNBs or antennas is switched to 0/12V, select what LNB and antenna are used enable or
disable.
0/12V terminal is located on the rear of STB.
DiSEqC Input
According to the option and position of DiSEqC switch, select Disabled, Tone Burst A to B and DiSEqC A to D.
After setting the above mentioned value, press the OK
button to move to the Manual Search menu.
GB 33
Page 35
4. Guide of Main Menu
Motorised System
The Motorised System is used to set the DiSEqC 1.2 motor by Eutelsat pecification. If you wish to use this
system, please refer to Motorised System.
**
Manual Search
Set the search parameters(Frequency, Symbol Rate, etc.) to manually
find the services that you have selected in the transponder.
The bar on bottom of the submenu shows the signal level and the signal
quality (BER) of the entered parameters.
Antenna Alternative
Select the target antenna for Manual Search. The Satellite Name helps you select Antenna Alternatives. This
is only for reference and cannot be changed on this menu.
Frequency
Use the NUMERICAL (0~9) buttons on the remote control unit.
Symbol Rate
Inputs the Symbol Rate of the transponder you want to find. Use thebuttons or Numerical buttons on the
remote control unit.
FEC(Forward Error Correction)
Use thebuttons to select the Forward Error Correction of the transponder. You can select the value of
Auto, 1/2, 2/3, 3/4, 5/6 and 7/8.
Network Search
•You can select Yes or No. When you select “Yes”, you can find more transponders using the home
network.
•As it refers to NIT during searching, if there is the frequency information of other transponder, it searches
the other transponder besides the transponder that the user inputs.
Automatic Skip
•You can select Yes or No. When you select “Yes”, the search will skip all scrambled services.
•When the found services are scrambled during searching, they are not listed up.
GB 34
Page 36
4. Guide of Main Menu
Advanced Search
Performs a manual search with the ability to enter PID(Video/Audio/ PCR)
values. This mode is necessary when you search for the signal that has
abnormal service Infornation tables.
The setting of the sub items is the same as Manual Search.
Video PID/Audio PID/PCR PID
You can set PID to search for services.
1. Use the
2. Use the NUMERICAL (0~9) buttons on the remote control unit to enter a decimal PID value.
3. In the hexadecimal input mode, press one of the NUMERICAL (0~9) buttons to display a hexadecimal
keyboard.
4. Enter a hexadecimal PID value.
Note: If no PID is input(Auto is displayed), the Advanced Search functions same as Manual Search.
5. After the above mentioned value is set, press the OK
**
Service Search OSD
•If you press the EXITbutton during the search, then Service
Search stops and the searching menu will appear.
•When you find all the services, the following picture appears.
•Before saving it, you can select the services you want to delete.
buttons to select PID input mode.
button to start Service Search.
Found services OSD
•The picture above shows services that are found after Manual Search.
•Use the RED
To unmark a service, select the service and press the RED
•Press the OK
•Then Service Search menu appears again. When you exit from all menus, the first service of the found
service list is played.
**
In the bottom of found service screen, network, the information of transponder and the number of found
service that the services belong to are displayed.
The deleted service by the RED
The deleted service is not included in this number. “Free” applies to the empty space of the memory. It will be
used to store future services.
button to mark the services that you want to delete.
button again.
button to save, or press the EXITbutton to exit without saving.
button is excepted from counting of the number of services.
GB 35
Page 37
4. Guide of Main Menu
Automatic Search
When you enter the Satellite Name that is set in Antenna Setting menu,
search all of the selected satellite without inputting the extra frequency.
Antenna Alternative
Select the target antenna for Automatic Service Search.
The attribute of this antenna alternative number is already set in Antenna Setting menu and the Satellite Name
is helpful in the selection of the antenna, but in this menu you cannot change the Satellite Name.
Automatic Skip
You can select Yes or No. When you select “Yes”, the search will skip all scrambled services. When the found
services are scrambled during searching, they are not listed up.
Search Type
•You can select one of two modes(Quick or Detail).
•When you select Quick mode, it searches the service by search parameters that is preset.
•When you select Detail mode, it searches the service through all field of tuner (950-2150MHz).
Network Search
•You can select Yes or No. When you select “Yes”, you can find more transponders using the home
network.
•If there is the frequency information of other transponder, it searches the othe transponder besides the
transponder that the user inputs.
**
Detail Mode
The pre-fixed symbol rate list is changed according to Antenna Alternative
and Satellite Name. If you want to add or change it, press the RED
button.
** The value of Pre-fixed symbol rates can not be editable.
GB 36
Page 38
4. Guide of Main Menu
The screen of the Symbol Rate Add/Change mode is as follows:
1. When you press the RED
trimmed with green edges meaning edit is possible.
2. You can easily put optional value with using NUMERICAL (0~9) buttons.
3. Press the RED
If you press the OK
moves left or right column use the
the EXIT
To delete a Symbol Rate in the above list, press the 0 (NUMERICAL button) in the selected position and
then the symbol rate disappears.
The range of Symbol Rate that is input additionally is 16-30Ms/s.
Note: The user should select the Satellite name in Antenna Setting menu. When the user types the Satellite
Name separately, the search type is fixed to the Detail mode.
button for confirmation, and you will successfully exit from input mode.
and the REDbutton to exit from input mode.
button after selecting detail mode from search type, blue box will be
button at symbol rate value input mode, the value will be confirmed, and if you
buttons, you can differ values of symbol rate to input. Then press
**
Press the OKbutton anywhere to start Automatic Search. The screen
during searching is as follows.
It searches with varying frequency, Symbol Rate and FEC etc. Satellite
Name is the name that the user selects to correspond with Antenna
Alternative of Antenna Setting.
The progress bar appears on bottom of the screen.
During the search, services that are found are displayed as follows:
1. Press the EXIT
2. After the search is finished, the appropriate message appears.
3. Press the OK
button during Automatic Search to stop search.
button to return Service Search menu.
**
GB 37
Page 39
4. Guide of Main Menu
4. Status
STB Status
Displays the information of H/W Version, S/W Version, Loader Version, CI
CAM of STB, and so on.
Signal Detection
Shows the Signal Level(AGC level) and Signal Quality(BER) of the
current service and is help to the initial antenna setting.
**
STB Upgrade
You can download and upgrade the software of this STB via a satellite
when the software of new version is released.
Do not turn off the STB during downloading.
When the power is switched OFF, turn on the STB and the process will be
continued.
**
•CRCI-5500+ models are not applicable.
**
5. Default Setting
Enter the PIN code to access the Default Setting menu.
Confirmation message “The default values are restored” will appear.
Press OK to start performing default setting. Press CANCEL to cancel the
operation.
**
GB 38
Page 40
4. Guide of Main Menu
6. Conditional Access
For Viaccess Embedded
This menu allows the user to view the information on the Smart Card and
Viaccess conditional access system such as general Smart Card
Information, Service List, Change Maturity Rating and Change PIN code.
General Smart Card Information
You can see the Unique Address, so user Address, Current Maturity Rating of the Smart Card.
Service List
Services or Bouquets are encrypted by Viaccess and operators name, like TPS or ABsat, are displayed on the
TV screen.
To get more detailed information of viewing rights of services or Bouquets, press the OK
Change Maturity Rating
The STB is required by Viaccess to include a parental control facility for the viewing of restricted services.
This can be set to “No block” or for ages ranging from 4 to 18.
The correct PIN code is required to change this option.
button.
Change PIN code
When you buy a new Smart Card, the initial PIN code is set to “NULL”.
Therefore, it is recommended that this PIN code should be changed.
This PIN code is available only on Conditional Access Menu.
Enter this PIN code to see the blocked Viacces Service.
**
•Specifications are for VACI-5300+ models.
•The supported functions vary depending on CAS version.
**
For CryptoWorks Embedded
This menu allows the user to view and change information on the Smart Cards such as available entitlements,
Maturity Rating and PIN code. Besides, you can view the mails from programme providers.
General Smart Card Information
Card label will be displayed as issuer’s name on the TV screen.
Programmes or Bouquets which are encrypted by only CryptoWorks(TM) and distributor labels displayed on
the TV screen such as Wizja TV or MTV Europe and more.
To get more detailed information of viewing rights of channels or bouquets, press the OK
**
button.
GB 39
Page 41
4. Guide of Main Menu
•Smart Card details
You can see smart card address, the validity date and current maturity rating.
Available Entitlements
The user will select a single programme provider by selecting its distributor label and you can get the
information of available entitlements.
**
•Subscription
You can see the vaild period of each service.
•PPV(Pay Per View)
If you purchased events in advance, the entitlements of Pay Per View events will be displayed.
•IPPV(Impulse Pay Per View)
You can purchase an event during the active broadcast of the event without pre-ordering. The
entitlements of Impulse Pay Per View events will be displayed. In this menu you need PIN code.
Maturity Rating
The STB is required by CryptoWorks(TM) to include a parental control facility for the viewing of restricted
programmes.
This can be set to “Disable MR” or PG(Parental Guide) to over 18.
The correct PIN code is required to change this option.
PIN Code
In this menu you can make PIN code enabled, disabled or changed.
**
•Enable PIN code
You can enable the PIN code.
•Disable PIN code
You can disable the PIN code.
•Modify PIN code
You can change the PIN code by using the NUMERICAL (0~9) buttons on the RCU. You will need to
enter the old PIN code before you can enter new PIN code.
Mail box
The STB can receive maximum 10 mails from programme providers.
To check and see the mails press the OK
button.
In the Mail list you can view or delete the mails.
If you store 10 mails and a new mail arrives, the oldest mail will be erased and the new mail will be stored.
**
•Specifications are for CRCI-5500+ models.
•The supported functions vary depending on CAS version.
GB 40
Page 42
4. Guide of Main Menu
7. Common Interface
You can enjoy not only scrambled services using the Conditional Access
Modules(CAM), but also Free-To-Air services.
This STB currently supports six kinds of CAM(VIACCESS™, Nagravision,
CONAX, CryptoWorks(TM), Irdeto or Mediaguard).
Common Interface module and Smart Card depend on the service
provider. If you need CAM, contact your service provider or distributor.
Note: If CAM is not used, then only Free-To-Air services are available.
**
4.5 Utility
STB supports additional functions such as Calendar and Biorhythm.
At the Biorhythm use the
date to see your current biorhythm status.
buttons to adjust your birth year and
**
GB 41
Page 43
5. Motorised System
1. DiSEqC 1.2 User Instructions
If you have a DiSEqC 1.2 motorised system, then you can use the DiSEqC 1.2 functions available.
The following instruction describes how to use the DiSEqC 1.2 functions to store the positions of the satellites
and to search for the services(STAB Rotor Sat motor recommended).
**
2. Satellite Setting Menu Options
When DiSEqC Motorised System is Enabled in the Antenna Setting, a new menu is available for configuring
the motor. This menu is called Satellite Setting and is accessed by pressing the OK
Antenna Alternative is highlighted in the Manual Search menu.
The following options are available on the Satellite Setting menu.
Satellite Name
A selection of satellite names that can be used to identify a motor position. If the satellite name you require is
not available, please use other. In installer mode the Satellite Name Reference refers to the 0 position of the
motor.
Movement
In user mode this is used to fine-tune the position of the motor for better reception.
In Installer mode this is used to search for the position of a satellite manually.
button while the option
Motor Control
Search
Goto
Store
Reset
DiSEqC Command Mode
Changes the current mode between Installer and User.
GB 42
:
Searches for services on the chosen transponder.
:
Moves the motor to the stored position of the selected satellite name.
:
Stores the current position of the motor for the selected satellite name.
:
Resets all stored positions of the motor relative to the 0 position. (Installer mode only)
Page 44
5. Motorised System
3. Setting your STB for DiSEqC 1.2
You must set your STB up so that it is ready to use DiSEqC 1.2. To do so, do as follows
1. Press the MENU
2. Select Service Searching option and press the OK
display the Service Searching menu.
3. Select Antenna Setting option and press the OK
display the Antenna Setting menu.
4. You must set up a separate antenna alternative for each satellite
position required.
5. Select the name of the satellite you wish to use.
6. Select the correct LNB frequency for the LNB you are using.
7. Set the Motorised System to Enable using thebuttons.
8. The option DiSEqC Input Selection should now be disabled.
This option is used for DiSEqC 1.0 and cannot be used in conjunction with DiSEqC 1.2.
Your STB is now ready to use DiSEqC 1.2. To return to the Main Menu, use the EXIT
you are at the Main Menu.
**
4. Initial Satellite Position Search
This is required when you first set your STB up to use DiSEqC 1.2 and
sets the positions of all pre-programmed satellites.
**
1. Make sure your motor is installed correctly with the calibrations
adjusted for the region you are situated. (Please consult the local
distributor for your motor.)
2. Make sure your STB is set up to use DiSEqC 1.2. (see section 2
above).
3. On the Main Menu, select Service Searching option and press the
OK
4. Highlight the option Antenna Alternative and press the OKbutton to display the Satellite Setting
menu.
5. Highlight the DiSEqC Command Mode option and use the
and press the OK
6. Highlight the Motor Control option and use the
OK
7. You will now see a warning message, press the OK
pre-programmed satellites should now be correct. If you have any other make or model of DiSEqC 1.2
motor then you may need to store the satellite positions in yourself(Please refer to the user manual for
your motor).
8. Highlight the DiSEqC Command Mode option and use the
press the OK
9. You should now be ready to start storing services for the various satellites(see 5 onwards).
button, you should now see the Service Searching menu.
button.
button, to display the Main Menu.
button, to
button, to
button until
buttons to change the value to Installer
button.
buttons to change the value to reset and press the
button to continue. All motor positions of the
buttons to change the value to User and
button.
GB 43
Page 45
5. Motorised System
5. Motor Limit Setting
Use this option to set the East and West limits of the motor. This should be used to prevent your dish from
hitting anything that may be obstructing the path of the dish.
1. Enter the Satellite Setting menu. (see section 1)
2. Press the i
3. Highlight the Limit Setting option and use the
this.
(Warning: When this option is disabled your motor will be able to
move beyond any limits that have been stored - please take care in
case there are anything obstructing the path of your dish.)
4. To set the East Limit:
a.Select Movement and use the
motor East or West until the motor is at the position you wish
to use as your East Limit. Use the
motor at the correct position.
b.Highlight the Store East Limit option and press the OK
button to store the current position as your East Limit.
To set the West Limit:
a.Select Movement and use the
motor East or West until the motor is at the position you wish
to use as your West Limit. Use the
motor at the correct position.
b.Highlight the Store West Limit option and press the OK
button to store the current position as your West Limit.
button to access the Motor Limit Setting menu.
buttons to disable
buttons to move your
buttons to stop the
buttons to move your
buttons to stop the
**
GB 44
Page 46
5. Motorised System
6. Manual Satellite Search
The purpose of this is to set the motor position for each satellite manually. This is useful if the satellite you
require is not available from the pre-programmed list (see 3 above).
**
To do this, you must access the Satellite Settings menu. Do as follows;
**
1. Select Service Searching from the main menu and press the OKbutton, to display the Service
Searching menu.
2. Select the Manual Search option and press the OK
Select the relevant Antenna Alternative that you are using for this satellite.
3. Enter the Frequency, Polarisation, Symbol Rate and FEC of a transponder on the satellite you wish to
find. This transponder information should be unique to this satellite.
4. Select the Antenna Alternative option and press the OK
menu.
5. Highlight the option DiSEqC Command Mode and using the
6. Highlight the option Satellite name and use the
others if the name of the satellite you want does not appear.
7. When you have selected the satellite you wish to find, go down to the Movement option and again using
the
buttons to start the motor moving.
8. You should move the motor as far west as possible and the move it east so that you cover the complete
movement range of the motor.
9. During the move from west to east the Signal Quality bar should register a signal once. This is the
position of the satellite. If there are two or more different positions which registers a signal, then you
must choose another frequency that is unique to the satellite you want.
10.Use the Signal and Strength Quality bar at the bottom of the screen to judge the best position of the
dish.
11.Use the
buttons to stop the motor when required.
12.When you have the best position of the dish go to the Motor Control option and using the
select store and press the OK
button. The position of the satellite should now be stored.
13.If you do not store this position, it will be lost when you exit the menu.
14.Repeat the process for each satellite if required, remembering to use a different antenna alternative for
each satellite.
button, to display the Manual Search menu.
button, to display the Satellite Settings
buttons change this to Installer.
buttons to select the satellite you want to find, use
buttons
GB 45
Page 47
5. Motorised System
7. Moving to a pre-set Satellite
Once you have stored the positions of the satellites you want(see left below) you can now search for the
services transmitted from them. Before you can do this, you must move the motor to the position of the
satellite you wish to search. To do this, you must access the Satellite Settings menu. Do as follows ;
1. Select Service Searching from the Main Menu and press the OK
Searching menu.
2. Select the Manual Search option and press the OK
3. Select the Antenna Alternative option and press the OK
menu.
4. In the Satellite Settings menu ensure that you have DiSEqC Command Mode option set to User.
5. Highlight the option Satellite Name and use the
6. When you have selected the satellite you wish to view, go down to the Motor Control option and again
using the
7. The motor will now move to the position of the selected satellite.
8. The Movement option is used to fine-tune the position of the motor.
9. When using the Movement option for fine-tuning, you must remember to store the changes you have
made or else these will be lost.
buttons select go to and press the OKbutton.
button, to display the Manual Search menu.
button, to display the Satellite Settings
buttons to select the satellite you want to view.
**
8. Searching for services on your selected satellite
Once you have moved the motor into position, you can search for the channels transmitted from the relevant
satellite. To search for services on your new selected satellite, Do as follows ;
1. Move the motor to the position of the satellite you wish to search.
(see section 6 above)
2. Select the service searching from the Main Menu and press the OK
button. To display the Service Searching menu.
3. Select the manual search option and press the OK
display the Manual Search menu.
4. Now enter the Frequency and Symbol Rate using the NUMERICAL
(0~9) buttons.
Next enter the Polarisation and FEC values using the
5. When you have entered all these details in, press the OKbutton and the search will begin.
6. When the search has finished, press the OK
7. Repeat the process for all the transponders you want from this satellite.
button to
buttons.
button to view.
button, to display the Service
GB 46
Page 48
5. Motorised System
9. Automatic Search
It is possible to use automatic search using the DiSEqC 1.2 motorised system.
1. Ensure that the positions for the satellite you want to search is correct. (see Section 3 and 5 above)
2. In the Main Menu, select the option channel searching and press the OK
3. In the Service Searching menu, select the Antenna Alternative that you have set for this satellite.
4. When you search new services, please refer to Automatic Search.
5. When the search has finished, press the OK
**
Now that you have stored all the positions of the satellites and searched for all the services you want, you can
now use your STB as normal. When you change to a service that is being transmitted from a different satellite,
you will have to wait a few seconds to allow the motor to move into position to receive the new service.
button to store and view the services.
button.
GB 47
Page 49
6. Troubleshooting Guide
ProblemSolution
About STB
Does not display any
message on the front panel
or STB has no power.
No PictureEnsure that the STB is switched on (see above).
Poor picture qualitySee "No Picture" above.
No SoundSee "No Picture" above.
Remote Control does not
operate
Check the main power cable and check that it is plugged into a suitable
power outlet.
Check you have switch the STB main power switch ON at the rear of the
STB.
Check whether STB is in Standby mode.
Check the video output port (SCART & RCA Jack) is firmly connected to
the TV or VCR.
If you are using the RF Output, check that the RF Lead is connected firmly
to the STB and TV/VCR.
Check that you have selected the correct channel or Video Output on your
TV.
If you are using the RF Output, check that you have correctly tuned the
UHF channel of the STB or TV.
Check the brightness level of the TV.
Check the signal level, if this is low then try adjusting the alignment of your
dish.
Check the volume level of the TV and STB.
Point remote control directly towards the STB.
Check and replace batteries.
On-Screen Error Messages
No or Bad SignalCheck the LNB - replace LNB if necessary.
Check the cable from the LNB.
Check the position of the dish - realign dish if necessary.
If you are using a DiSEqC 1.0 switch, check that you have connected the
LNBs to the correct connections on the switch.
Check the "Signal Level" and the "Signal Quality" in the Signal Status
menu.
Service is not running or
scrambled / No access to
the service slot.
GB 48
Check whether the common Interface module and Smart card are correctly
inserted.
Check whether the common Interface module and Smart card is
appropriate for the selected service.
Page 50
6. Troubleshooting Guide
ProblemSolution
Please check the card / No
right for this service / No
smart card in slot and please
insert your card (when using
the CAM)
Time Display
The front panel does not
display the time.
Time displayed on the front
panel is incorrect.
Service Search
"No Signal" in Manual
Search
Front panel Error Messages
Check that the Smart card is inserted correctly.
Check the Smart card is appropriate for the selected service.
Check the subscription rights of the Smart card.
Make sure you have switched on the STB.
Switch the STB on and tune to a service to allow the STB to receive the
time sent with the signal by the service provider.
Front panel will only display the time in Standby mode.
Adjust the time in the Time Settings menu.
Check the "Signal Level" and the "Signal Quality" in the Signal Status
menu.
Check the LNB - replace LNB if necessary.
Check the cable from the LNB.
Check the position of the dish - realign dish if necessary.
**
DiSEqC 1.0
Check that you have connected the LNBs to the correct connections on the
switch.
Check that you have set the correct settings in the Antenna Setting menu.
**
DiSEqC 1.2
Check that you have selected this in the Antenna Setting menu.
Check that the dish is aimed at the correct satellite.
: Incorrect data block
Try switching STB power Off and On.
(CRC-16)
: Invalid systemIDCheck whether the system ID is different for Software and STB.
: UART RX/TX time
Try switching STB power Off and On.
out
**
•If you can't solve the problem even referring this Troubleshooting Guide, contact us via our homepage.
**
HomePage : http://www.humaxdigital.com
GB 49
Page 51
7. Menu Map
**
GB 50
Page 52
8. Specification
Tuner & Channel
Input ConnectorF-type, IEC 169-24, Female
Frequency Range950 - 2150 MHz
Input Impedance75unbalanced
Signal Level-25 to -65dBm
IF480 MHz
IF Band width36 MHz
LNB Power & PolarisationVertical : +13.5V
Horizontal : +18V
Current : 500mA Max. Overload Protection
22 KHz ToneFrequency : 22 ± 4KHz Amplitude : 0.6 ± 0.2V
0/12V DC OutputCurrent Max. 50mA
DiSEqC ControlVersion 1.0/1.2 Compatible
DemodulationQPSK
Input Symbol Rate2-31 Ms/s
FEC DecodeConvolutional Code Rate 1/2, 2/3, 3/4, 5/6 and 7/8 with Constraint Length K=7
MPEG Transport Stream A/V Decoding
Transport StreamMPEG-2 ISO/IEC 13818
Transport stream Specification
Profile LevelMPEG-2 MP@ML
Input Rate15 Mbit/s Max
Aspect Ratio4:3, 16:9
Video Resolution720 x 576
Audio DecodingMPEG/MusiCam LayerI&II
Audio ModeSingle channel/Dual channel/Joint stereo/Stereo
Sampling32, 44.1 and 48KHz
Memory
Main ProcessorTMIPS R3930(81MHz)
Flash Memory3Mbyte
Graphic(MPEG) & System DRAM 4Mbyte
RF-Connector75, IEC 169-2, Male / Female
Frequency470 - 860 MHz
Output ChannelCH21-69, CH28-69 or CH13-62 for the Remodulator
TV StandardPAL I/G/B/D/K selectable by Menu setting
Preset ChannelCH36(or TBD). Software changable by Menu
Power Supply
Input Voltage190 - 250V AC, 50/60 Hz
TypeSMPS
Power ConsumptionMax. 35W
Standby Power11W
ProtectionSeparate internal fuse. The input shall have lightening Protection
Physical Specification
Size(WxHxD)370 x 60 x 280 mm (Excluding the Foot)
Foot height is 8 mm
Weight(Net)Around 2.8 kg
Operating Temp0to+45
Storage Temp-10to+70
Storage Humidity5% ~ 95% RH(Non-Condensing)
**
You can use a special antenna switch with DiSEqC commands.
**
When changing ASTRA1 to EUTELSAT for example, a DiSEqC command is sent with the 22KHz tone
through the antenna cable. The antenna switch will change ASTRA1 to EUTELSAT. The concept of DiSEqC is
a protective trademark of EUTELSAT.
**
Data rate decides the picture quality of digital TV programmes.
Data rate of about 5-6 Mbit/s coincides with the picture quality of a analog TV programme.
**
•Please note : The specification of the STB may be changed without notice in advance.
GB 52
Page 54
9. Glossary
•Antenna
A device that collects and radiates electromagnetic waves. Includes a satellite dish and a broadband
antenna.
**
•Forward Error Correction(FEC)
A system of error control for data transmission.
**
•Frequency
The number of cycles or events per one second, which is expressed in the unit of Hertz(Hz).
**
•Intermediate Frequency(IF)
A frequency to which a carrier frequency is shifted as an intermediate step in transmission or reception.
**
•Low Noise Block(LNB) Downconverter
A low noise microwave amplifier and converter which downconverts a range of frequencies to IF range.
**
•Packet Identifier(PID)
A set of numbers that idenitifies transport stream packets containing data from a single data stream.
**
•Polarisation
Characteristic of an electromagnetic wave determined by the orientation of the electricfield vector.
**
•Quaternary Phase Shift Keying(QPSK)
Phase-shift keying in which four different phase angles are used.
**
•Service
A channel to which a decoder or TV is tuned.
**
•Transponder
An automatic device that receives, amplifies and retransmits a signal on a different frequency.
GB 53
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.