Page 1
EchoLife Bridge GPON Terminal
Quick Start
Page 2
Safety Information
Before using the device, read these precautions carefully. Follow these precautions and instructions
to ensure optimal product performance and to avoid danger and legal or regulatory violations.
Fire-proof Precautions
Keep the device away from re or heat sources, including electric heaters, ovens, stoves, and
candles. Otherwise, the shell of the device may become hot or melt, causing re in extreme
cases.
Replace deteriorated cables or power socket components on the power supply line or near the
device in a timely manner to eliminate safety risks.
Potentially Explosive Area
Do not place or operate the device in an environment with that contains ammable or explosive
gas or smoke.
Do not place ammable or explosive materials below or above the meter cabinet.
General Safety Precautions
Do not lead the strength member of the optical ber or other metal parts indoors. Do not install
telephone lines, network cables, power adapters or power adapter cables outdoors. These
measures will help to prevent damage to the device and injury to people, which are especially
possible during thunderstorms.
If the power adapter is damaged from human factors, and the inside circuit is exposed, do not
touch the exposed parts. Otherwise, security risks are present.
Keep the device out of the reach of children. Components and accessories are small and could
pose a choking risk.
Looking directly at the optical port may injure your eyes.
Do not use any power adapters that are not in the standard conguration. Otherwise, the device
may be abnormal or unsafe.
If a backup power unit (BBU) is available in the packing box, do not disassemble it, ret it, or
put it in a re. Otherwise, it may create a safety risk.
Instructions for Use
Use the device in a clean and well-ventilated indoor environment, out of direct sunlight.
Store devices and accessories in temperature –10°C to +35°C and relative humidity 30%–85%
RH for at most 9 months. If the ambient temperature or relative humidity is overhigh or overlow,
the device may be faulty.
Install the device in strict compliance with the requirements of the supplier. Ensure there is at
least 10 cm space surrounding the device for heat dissipation. During installation, keep the
device away from ammable objects and electric appliances that generate strong magnetic or
electric elds, including microwave ovens, refrigerators, and mobile phones.
The described input voltage range should comply with the local power grid. For example, the
input voltage of the device is 200–240 V AC for European Union; the input voltage of the device
is 100–130 V AC for the United States of America.
The power supply voltage of the device must meet the requirements on the input voltage of the
device.
Before use the power adapter, please check no damage on the adapter.
Use dry hands to connect or disconnect cables. Stop using the device and switch off the power
before connecting or disconnecting cables.
When there is lightning, switch off the power and disconnect all cables, including the power
cable, optical ber, and network cable.
Prevent objects from entering the device through the heat dissipation hole. Prevent water or
other liquids from entering the device.
1
Page 3
NOTE
Do not place any objects on the device, so that the device will not be overheated or deformed.
If an abnormality occurs, for example, liquid enters the device, or the device emits smoke,
unusual sounds, or odors, stop using the device immediately. Switch off its power, and
disconnect all cables to the device, including the power cable, optical cable, and network cable.
Before cleaning or maintaining the device, stop using it, close all Apps, and disconnect all
cables.
Do not use any strong chemicals, detergents, or other chemical agents. Use a clean, dry, soft
cloth to wipe the shell and accessories of the device.
Keep the device dry when it is stored, transported, or used. Prevent the device from colliding
with other objects. Otherwise, the device and its accessories may be damaged, and the device
may become faulty.
No unauthorized unit or individual may disassemble or modify the device or accessories.
Dispose of the packing materials, expired batteries, and old or abandoned devices in
accordance with local laws and regulations. Recycling them is strongly recommended.
Product Overview
Product Function
HG8010 series
HG8110 series
HG8012 series
HG8120 series
1 Ethernet port
1 Ethernet port
1 POTS port
1 Ethernet port
1 CATV port
2 Ethernet ports
1 POTS port
4 Ethernet ports
HG8242 series
2 POTS ports
1 CATV port
HG8040 series
HG8240 series
If some device types are not in the preceding list, refer to http://www.huawei.com.
4 Ethernet ports
4 Ethernet ports
2 POTS ports
2
Page 4
Technical Specications
NOTE
Power adapter input: 100–240 V AC, 50/60 Hz
System power supply: See the nameplate on the device.
Ambient temperature: 0ºC to +40ºC
Ambient humidity: 5%–95% (non-condensing)
For other technical specications, see the following table.
GPON Terminal
(Including the Power
Adapter)
HG8010 series About 270 g 3.6 W
HG8110 series About 300 g 5.5 W
HG8012 series About 350 g 6 W
HG8120 series About 350 g 5.5 W
HG8242 series About 400 g 14 W
HG8040 series About 400 g 7.5 W
HG8240 series About 400 g 7.8 W
If the appearance of the product in this document differs from the actual product, the actual product
prevails.
Weight
Maximum System Power
Consumption
Installing the GPON Terminal
1. Do not install GPON terminals outdoors or on the outdoor cabinets.
2. GPON terminals can be mounted onto a wall or be placed on a workbench. Do not
install GPON terminals in other modes, such as the ceiling.
3.The terminal cannot be connected to other devices such as GPON terminals, switch
and router.
3
Page 5
Mounting a GPON Terminal On The Desk
1
2
3
3 mm
1 2
3
4
WLAN
Reset
WPS
The schematic diagram for placing the device on a desk horizontally is as
follows (The HG8240H5 is used as an example here.):
Mounting a GPON Terminal Onto The Wall
Step 1 Mark the positions of two holes used for mounting a GPON terminal,
ensure that the two holes have the same spacing as the two
mounting holes.
Step 2 Select a proper drill according to the outer diameter of the screws.
Use a hammer drill to drill the marked positions on the wall. Then
clean the wall and install two expansion bolts.
Step 3 Use a screwdriver to fasten the screws into the expansion bolts,
leaving the heads of the screws 3 mm over the wall. Then install the
GPON terminal to the screws.
4
Page 6
NOTE
This terminal is mainly placed horizontally on a desk. When it is mounted
6
onto a wall, the silkscreen of its indicator is reversed. If you have a special
requirement on the silkscreen, purchase another terminal.
Connecting Cables
This document uses the HG8240H5 as an example to describe the connections. Ports
on GPON terminals of other types may be different. Therefore, connect cables based
on the ports that are actually supported by the device. If the external device is different
from the device in the figure, refer to the description for connections of the external
device.
5
1 2
Power socket
Fax machine
TV set
4
IP STB
5
1
Power switch
2
Power port
3
POTS port
4
Ethernet port
5
Optical port
PC
6
Reset
3
Phone
Page 7
Step 1 Use an optical ber to connect the optical port on the ONT and the
optical port on the wall.
• The optical port of the HG8242 series, HG8240 series and HG8040
series are at the back of the device. For how to connect the optical
port, see the following gure (The HG8240H5 is used as an example
here.):
• For how to connect the optical ports of other ONTs, see the following
gure:(Use an optical ber to directly connect the OPTICAL port on
the ONT to the optical port on the wall.) The HG8110F is used as an
example here.
6
Page 8
NOTE
NOTE
1.The optical connector connected to the
NOTE
NOTE
the type of the optical connector connected to the optical port in the wall is determined by
practical conditions.
2.To ensure normal use of bers, make sure that the ber bend radius is larger than
30 mm.
OPTICAL
port is an SC/APC connector, and
Step 2 Use a network cable to connect the LAN port to a PC or the Ethernet port on
the IP STB.
Step 3 Use a phone line to connect the TEL port to a phone or fax machine.
Step 4 Use a power adapter to connect the POWER port to the power socket.
The preceding gure connects the power adapter as an example. For details about how to
use the backup battery unit, see the usage guide to the backup battery.
Step 5 Press the ON/OFF power switch.
Logging in to the Web Conguration Window
Step 1 Set the IP address of the PC in the same subnet as the management IP address
of the GPON terminal.
You can nd the default management IP address on the nameplate of the
device.
Step 2 Enter the management IP address of the GPON terminal in the address bar of
Internet Explorer and press Enter.
The login window is displayed.
Step 3 In the login window, select your preferred language, enter the user name and
password ( printed on the nameplate of the device.), and click Login. After the
password is authenticated, the Web configuration window is displayed.
Shipped from different manufacture batches, the nameplates of some devices do not have
-
the IP address, user name, and password printed. In such a case, log in to the device using
192.168.100.1 (or 192.168.1.1), root (user name), and adminHW (password).
- If you do not perform any operations after logging in to the system for ve minutes, you will
exit the system and the system automatically returns to the login interface.
- The system will be locked if you input incorrect user name and password three consecutive
times. One minute later, it will be unlocked.
- Change the initial password after logging in to the web page.
7
Page 9
Indicator Description
Table 1 Indicator status description 1
Indicator Status Description
CATV
TEL1–TEL2
LAN1–LAN4
LOS/PON See Table 2.
POWER
Table 2 Indicator status description 2
Status
No.
1 Off Off
2
3 Steady on Off
4 Off
5
6
Steady on
Off
Steady on
Blinking Service ows are transmitted.
Off
Steady on The Ethernet connection is in the normal state.
Blinking Data is being transmitted on the Ethernet port.
Off The Ethernet connection is not set up.
Steady green The terminal is powered on.
Off The power supply is cut off.
Status
PON LOS
Blinks twice
a second
Blinks twice
a second
Blinks once
two seconds
Off
Blinks once
two seconds
Blinks twice
a second
Blinks once
two seconds
The CATV function is enabled and CATV signals
are received.
The CATV function is disabled or CATV signals
are not received.
The ONT is registered with the softswitch but no
service ows are transmitted.
The ONT is not powered on or fails to be
registered to the softswitch.
The GPON terminal is prohibited by the upperlayer device, contact the service provider for
help.
The GPON terminal attempts to set up a
connection with its upper-layer device.
A connection is set up between the GPON
terminal and its upper-layer device.
The GPON terminal is not connected to optical
bers or does not receive optical signals.
The GPON terminal is a rogue terminal,
contact the service provider for help.
The hardware is faulty.
Description
8
Page 10
Disposal and recycling information
The crossed-out wheeled-bin symbol on your product, literature or packaging reminds
you that all electronic products must be taken to separate waste collection points at the
end of their working lives; they must not be disposed of in the normal waste stream with
household garbage. It is the responsibility of the user to dispose of the equipment using
a designated collection point or service for separate recycling of waste electrical and
Proper collection and recycling of your equipment helps ensure electrical and electronic equipment
(EEE) waste is recycled in a manner that conserves valuable materials and protects human health
and the environment, improper handling, accidental breakage, damage, and/or improper recycling at
the end of its life may be harmful for health and environment. For more information about where and
how to drop off your EEE waste, please contact your local authorities, retailer or household waste
disposal service.
Disposal of the device is subject to WEEE Directive Recast (Directive 2012/19/EU). The purpose of
separating WEEE from other waste is to minimize the potential environmental impacts and human
health risk of any hazardous substances that may be present.
electronic equipment (WEEE) according to local laws.
Reduction of hazardous substances
This device is compliant with the REACH Regulation [Regulation (EC) No 1907/2006] and RoHS
Directive Recast (Directive 2011/65/EU).
9
Page 11
FAQs
LOS
The
If the LOS indicator blinks once two seconds, check
If the GPON terminal blinks twice a second, contact the
The
Check whether the OPTICAL port and optical fiber is
The GPON terminal fails to register with the upper-layer
The phone does not ring upon an incoming call but
communication is in normal state when the phone is in off-hook
state.
The GPON terminal provides a maximum of 60 V AC
How to reset the GPON terminal?
Press Reset by using a needle-type object.
How can I restore factory defaults?
Press Reset by using a needle-type object for longer
indicator blinks.
whether the pigtail fiber is properly connected and the
connector is clean.
service provider for help.
PON
indicator is off.
properly connected.
device. Contact the service provider for help.
ringing current voltage. Check whether the ringing current
voltage of the phone is higher than 60 V AC. If it is higher
than 60 V AC, replace it with another phone.
than 10s to restore factory defaults and reset the GPON
terminal. If the indicator is off and then is lit, the system
restarts successfully.
10
Page 12
Warranty Card
Thank you for choosing Huawei Technologies Co., Ltd. To get better services,
please read this warranty card carefully, ll in the required information, and
preserve this card in good condition.
User Information
Personal or
company's full name:__________________________________________________
Address/Postal Code:_________________________________________________
Telephone:__________________________________________________________
Email:______________________________________________________________
Product Type:________________________________________________________
Product Serial Number:________________________________________________
Purchase Date:______________________________________________________
Invoice Number:______________________________________________________
Dealer's Name:______________________________________________________
Dealer's Address:_____________________________________________________
Dealer's Telephone:___________________________________________________
Preserve well. No reissue.
Dealer's Seal
Page 13
Limited Warranty
Subject to the exclusions contained below, Huawei Technologies Co., Ltd. (Huawei
for short) warrants its access terminals ("Products") to be free from defects in
materials and workmanship under normal consumer usage for one year from
the date of purchase of the product ("Warranty period"). During the warranty
period, a Huawei authorized service partner shall remedy defects in materials and
workmanship free of charge.
Special Notice:
1. The warranty card shall be applicable only after being stamped by the dealer.
2. The warranty card must be preserved in good condition and free of any scratch or
alteration.
3. To claim such service for defects that are not included in the following exclusion
terms, the warranty card and the invoice that records that product serial number
shall be presented to a Huawei authorized service partner.
Exclusions:
In any of the following cases, the warranty card becomes unenforceable or
inapplicable without prior notice:
1. The defects are caused by improper handling in transportation and assembly.
2. The defects are caused by the fact that the product is dismantled or altered by
anyone that is not from a Huawei authorized service partner.
3. The defects are caused by the fact that the product is used in a harsh environment
that is not suitable for the operation of the product.
4. The defects are caused by any force majeure including but not limited to re,
earthquake, lightning, and tsunami.
5. The defects are caused by the fact that the product is used or handled incorrectly,
roughly or not as instructed in the applicable User Guide.
6. The normal wear and tear, including but not limited to the normal wear and tear of
the shell and the power module, shall not be covered by the limited warranty.
7. The warranty card is altered or illegible, or the product serial number recorded on
the warranty card is inconsistent with the actual one imprinted or labeled on the
product.
In any case that is not covered by this limited warranty or should the warranty expire,
Huawei shall charge for the service(s) claimed for the products if the product is still
remediable. Huawei reserves all rights to interpret this limited warranty.
Huawei Technologies Co., Ltd.
Address: Huawei Industrial Base
Bantian, Longgang
Shenzhen 518129
People's Republic of China
Website: http://www.huawei.com
Page 14
Qualication Card
PASS
Copyright © Huawei Technologies Co., Ltd. 2018. All rights reserved.
No part of this document may be reproduced or transmitted in any form or by any
means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks and Permissions
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of
their respective holders.
Notice
The information in this document is subject to change without notice. Unless
otherwise stated, this guide serves only as a guide. All statements, information, and
recommendations in this document do not constitute a warranty of any kind, expressed
or implied.
Issue: 07
BOM number: 31505717
Loading...