Huawei HG530, HG530u Installation Instructions Manual

Installation Instructions

Wireless ADSL2+ Router
Huawei HG530 / HG530u

Minimum System Requirements............................................................................................................................................. 3

Package Contents ........................................................................................................................................................................4

LEDs ................................................................................................................................................................................................... 5

Ports ..................................................................................................................................................................................................6

Connecting the ADSL2+ Router ............................................................................................................................................. 7

PSTN Line ................................................................................................................................................................................ 8

ISDN Line ...............................................................................................................................................................................11

Internet Settings .........................................................................................................................................................................14

Wireless Connection ................................................................................................................................................................19

Turning the wireless network On/O /& Reset Router .................................................................................................24

Change the Username & Password for Internet access ................................................................................................25

Equipment Guarantee ..............................................................................................................................................................26

Online Security ............................................................................................................................................................................26

Connection Elements ...............................................................................................................................................................27

Contents

1 Pentium 4 Processor

2 Windows XP/Vista/7 or Mac OS 9.x

3 1 GB RAM

4 25 MB free hard disk space

5 10/100 Mbps Ethernet Network Card

Minimum System Requirements

1 ADSL2+ Wireless Router

1 Installation CD

Installation Instructions

2 Telephone Cables (RJ-11)

1 Ethernet Cable (RJ-45)

1 Power Transformer

1 Splitter

1 Filter (for PSTN)

Installation Instructions

Wireless ADSL2+ Router
Huawei HG530 / HG530u

Package Contents

LED

The following LEDs are found on the front side of the ADSL2+ Router.
Review the meaning of each LED below (Figure 1).

Color Status

On

Figure 1

O

Blinking

On

O

Blinking

On

O

Blinking

On

O

Blinking

On

O

Connection established

Connection is not established

Connection being established

Connection established

Connection is not established

Data is transferred over Ethernet

Ethernet connection is established

Ethernet connection is not established

• WAN connection is established

• Data is being transferred

• WAN connection is established

• No data is transferred
WAN connection is not established

• Wireless network mode is being activated

• Data is being transferred over WLAN

• Wireless network mode is active

• No data is being transferred over WLAN

• Wireless network mode is inactive

Meaning

LEDs

The ADSL2+ Router has the following buttons and ports (Figure 2):

PORT LABEL DESCRIPTION OPERATION

POWER Power Port

This port is used for

the 220V power transformer

RESETFactory setting reset button Resets factory settings

LAN 4 (STB) Ethernet Port for decoder

Connects to OTE’s Cable Television

over Internet Service

LAN 1-3 Ethernet Ports

for PC connection

They allow for the connection of

up to three PCs for access to the Internet

and local network creation

ADSL

Port for telephone

cable connection

Connects to the telephone socket

or the splitter

WLAN WLAN Button It turns the WLAN on/o

ON/OFFPower button It is used to power the device on/o

Figure 2

Ports

Follow the following instructions to connect the ADSL2+ Router
over a PSTN or ISDN telephone line.

Connecting the ADSL2+ Router

Connecting the ADSL2+ Router

PSTN Line

If you have a PSTN
telephone line (plain analog line),
connect the ADSL2+ Router
as shown below.

Using the blue cable, connect the blue port
on the splitter to the telephone socket.

Use the yellow cable to connect the network port (ETHERNET)
of your computer to one of the three rst yellow ports on the
Conn-x equipment.

WARNING: The purple port labeled STB is used exclusively to

connect the set-top-box required to receive OTE's Cable Television
over Internet service.

A. Use the grey cable to connect the grey
port on the splitter to the grey port on
the Conn-x equipment.

B. Next, connect the cable of your telephone
device to the black port on the splitter.

If you have a telephone set connected to the telephone socket,
you must disconnect it.

PSTN Line

PSTN Line

Connect the power transformer to the power port on the
Conn-x equipment and plug it to the mains socket.

Press the ON/OFF power button located on the side of the
equipment, to turn on your equipment.

The Power, ADSL, Internet, LΑΝ and WLAN LEDs will light.

To connect additional telephone sets to other sockets, each set
must be connected to a lter. Connect your telephone set to the
lter and the lter to the socket.

Note: If your telephone network is connected to any device

(alarm, telephone exchange, etc.), you must use an additional
ADSL lter or splitter. Please contact a specialized installer.

ISDN Line

If you have an ISDN telephone line,
connect the ADSL2+ Router
as shown below.

ISDN Line

Disconnect the cable that connects the telephone
set to the ISDN equipment (N.T. 1) from the telephone
socket and connect it to the black port on the splitter.

Note: If your telephone network is connected to any device

(alarm, telephone exchange, etc.), you must use an additional
ADSL lter or splitter. Please contact a specialized installer.

A. Using the blue cable, connect the blue port on the
splitter to the telephone socket.

B. Next, use the grey cable to connect the grey port
on the splitter to the grey port on the Conn-x equipment.

ISDN Line

Use the yellow cable to connect the network port (ETHERNET)
of your computer to one of the three rst yellow ports on the
Conn-x equipment.

WARNING: The purple port labeled STB is used exclusively to

connect the set-top-box required to receive OTE's Cable Television
over Internet service.

Connect the power transformer to the power port on the
Conn-x equipment and plug it to the mains socket.

Press the ON/OFF power button located on the side of the
equipment, to turn on your equipment.

The Power, ADSL, Internet, LΑΝ and WLAN LEDs will light.

Internet Settings

To install the ADSL2+ Router, insert the CD in the CD-ROM drive.
The CD must start automatically. If the CD fails to start automatically,
go to Windows Explorer, select the CD-ROM drive where the CD is
located, double click on setup.exe and follow the instructions.

If you cannot install the ADSL2+ Router using the installation CD,
follow the instructions given below:

Internet Settings

Internet Settings

Open your Browser.
At the address line type
http://192.168.1.1
and press Enter.
The screen shown on the
side will appear:

The ADSL, ATM, and Internet
Status LEDs must be green.
If one of the LEDs is red,
check the connections and
try again.

Internet Settings

Click on Administration.
The screen shown on

the side will appear:

Internet Settings

Enter admin in the Username eld. In the Password eld
enter the password you will nd on the label on the back
of your ADSL2+ Router and click on ΟΚ.
Note the Username and Password on the last page of the
brochure.

Internet Settings

The screen shown on the
side will appear:

In the Username eld
enter the username you
were given at the time
of purchase of your
Conn-x package
followed by @otenet.gr

In the Password eld
enter the password you
were given at the time
of purchase of your
Conn-x package. Click on
Apply to save the settings.
Now you are connected
to the Internet!

Close the Browser.

Wireless Connection

Follow the instructions below to connect wirelessly to the Internet.

Wireless Connection

Wireless Connection

To connect wirelessly to the Internet you must have completed the Internet Settings.

If you wish to connect from a desktop computer, you must have installed and activated the
wireless USB stick or wireless network card on your computer.

If you wish to connect wirelessly from a laptop you must have activated the wireless mode
(see the user manual that came with your laptop).

For easier installation, it is recommended to keep the factory settings. You can change them
later using the wireless network settings menu (see the user manual on the CD).

Wireless Connection

Double click on the wireless network icon on your computer to display
available wireless networks.

Wireless Connection

The name of your wireless network that you must look for
is the one that has the SSID name you will nd on the label
on the back of your equipment or on the CD jacket.

Note the SSID name on the last page of the brochure.

Click on the wireless network that corresponds
to the SSID name and click Connect.

Wireless Connection

On the screen that will appear enter the WPA network
security key you will nd on the label on the back of
your equipment or on the CD jacket labeled WPA, and
click on ΟΚ. Note the WPA network security key on the
last page of the brochure.

You will be connected to the network. Please wait…

Now you are connected wirelessly to the Internet! Attention! For each additional device you wish
to connect wirelessly you must repeat the steps in the section Wireless Connection or Connect
Wirelessly from the installation CD.

Turning the wireless network On/O /& Reset Router

The wireless mode is on. To turn it o, press and keep pressed the
WLAN button on the side of the ADSL2+ Router until the WLAN LED
on the top part of the ADSL2+ Router goes o. To turn the wireless
mode on, press and keep the same button pressed for more than
1 second. The WLAN LED will go on.

If you need to reset the factory settings of the ADSL2+ Router, rst
make sure the router is on. Press and keep the RESET button on the
back of the ADSL2+ Router pressed until all LEDs (except the Power
LED) go o.
Wait until the ADSL2+ Router LEDs come back on. Resetting the
factory settings will clear any information entered and saved in the
ADSL2+ Router.

Change the Username & Password for Internet access

If you wish to change your User name and Password (you can change the User name only once,
but you can change the Password as many times as you wish), open your Browser and on the
address bar type http://www.oteshop.gr/myservices/myid

In the page that will open under MY e-SERVICES
or Internet Services Administration click on
Change of conn-x username and password and
follow the instructions on the screen.

If you change the User name or the Password, repeat the Internet Settings.

The device comes with a one (1) year guarantee from the date of purchase.

Conn-x oers Online Security Services free of charge for 2 months, providing you a better and safer
Internet navigation experience, and protecting your computer from viruses, hackers & spam. Online
Security includes:

Instructions:
To install the Online Security, you must have rst successfully connected to the Internet. Open the

Browser and at the address line enter www.conn-x.gr and go to Add-ons, from where you can download
and install the Online Security service by Conn-x.

Anti-Virus: to protect against viruses, worms, trojans & spyware.
Firewall: to block access to your computer by unknown people.
Anti-Spam: to block spam.
Parental Control: to allow you to control and block access to web pages with unwanted content,

such as: violence, adult content, guns, drugs, etc.

Equipment Guarantee

Online Security

User name

SSΙD

WPA Network Security Key

Do you want to be the rst

to nd out about the best

Conn-x packages and oers?

for Internet access

Password

Equipment Password

Online Security Registration key

Equipment Username

for Internet access

Go to www.conn-x.gr and

nd out about all new releases!

You can ll in here your connection information:

APRIL 2011Please recycle

24-hour Technical Support Line

If you have any questions or need help before
and after the ADSL installation, call

(Local call rate throughout Greece)