A. Customer is responsible f or e nsuring that antennas used with the p roduct are of
the same type, with same or lower gains as approved and providing antenna reports to
Broadcom.
B. Customer is responsible for re g ression testing to accommodate chan ges to the
approved designs, new antennas, and portable RF exposure safety testing/approvals.
C. Appropriate labels must be affixed to the CUSTOMER Product that comply with
applicable regulations in all respe cts.
D. A user’s manual or instruction manual must be included with the customer
product that contains the text as required by applicable law. Without limitation of the
foregoing, an example (for illustration purposes only) of possible text to include is set
forth below:
1. USA—Federal Communications Commission (FCC)
FCC COMPLIANCE STATEMENT:
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
INFORMATION TO USER:
This equipment has been tested an d f o un d t o comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC R ule s. These limits are designed to pro v i de reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy. If not installed and used in
accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur i n a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by tuning the equipment off and on, the
user is encouraged to try and correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which th e receiver is
connected.
Page 1 of 7
OEM Installation Guidance Document
For 802.11bgn WLAN Module, SDGOB-1091
FCC ID: B94SDGOB1091; IC: 466D-SDGOB091
-Consult the dealer or an experie nced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
CAUTION: (this only applicable t o 5 GHz d e vice)
This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz
frequency range. FCC requires this product to be used indoors for frequency range 5.15
to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile
Satellite systems.
High power radars are alloca ted as primary users of the 5.25 to 5.35 GHz and 5.65 to
5.85 GHz bands. These radar stations can cause interference with and/or damage this
device.
System integrators must include the FCC ID on t he end product.
1. Antennas must be installed in the display section of Netbook/notebook/laptop
computer to provide at least XXcm separation distance from the transmitting antenna to
the body of user during normal operating condition.
2. Transmitting antenna(s) can o nl y be insta lled at the display section of com pute r. When
this device is installed other than notebook computers, at least 20 cm separation distance
shall be maintained between the transmitting antenna(s) to the body of user or nearby
person.
3. The antenna(s) used for this transmitter must not be collocated or operating in
conjunction with any other ante n na o r tra nsmitter within a host device, except in
accordance with FCC multi-transmitter product procedures.
4. Only those antennas with same type and lesser gain filed under this FCC ID number
can be used with this device.
5. The regulatory label on the final system must include the statement: “Contains FCC
ID: B94SDGOB1091 and/or IC: 466D-SDGOB09 1” or using electronic labeling method
as documented in KDB 784748.
6. The final system integrator must ensure there is no instruction pro vid e d in t he us er
manual or customer documentation indicating how to install or remove the transmitter
module except such device has implemented two-ways authentication between module
and the host system.
7. The final host manual shall include the following regulatory statement:
This equipment has been tested an d f o un d t o comply with the limits for a Class B digital
device, pursuant to Part 15 of FCC R ule s. These limits are designed to pro v i de reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy. If not installed and used in
Page 2 of 7
OEM Installation Guidance Document
For 802.11bgn WLAN Module, SDGOB-1091
FCC ID: B94SDGOB1091; IC: 466D-SDGOB091
accordance with the instructions, it may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur i n a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by tuning the equipment off and on, the
user is encouraged to try and correct the interference by one or more of the following
measures:
-Reorient or relocate the receiving antenna
-Increase the distance between the equipment and the receiver.
-Connect the equipment to outlet on a circuit different from that to which th e receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
2. Canada - Industry Canada (IC)
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any in terference, including interference that
may cause undesired operation of this device.”
L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes : (1) il ne
doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prêt à accepter
tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de
compromettre le fonctionnem ent du di sp ositif .
To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent is otropically radiated power (EIRP) is not more than that
required for successful communication.
Caution: (this only applicable to UNII device)
This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz
frequency range. Industry Canada requires this product to be used indoors for frequency
range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel
Mobile Satellite systems.
High power radars are alloca ted as primary users of the 5.25 to 5.35 GHz and 5.65 to
5.85 GHz bands. These radar stations can cause interference with and/or damage this
device.
Caution: Exposure to Radio Frequency Radiation.
To comply with RSS 102 RF exposure compliance requirements, for mobile
configurations, a separa tion distance of at least 20 cm must be maintained between the
Page 3 of 7
OEM Installation Guidance Document
For 802.11bgn WLAN Module, SDGOB-1091
FCC ID: B94SDGOB1091; IC: 466D-SDGOB091
antenna of this device and all persons. This device must not be co-located or operating in
conjunction with any other a ntenna or transmitter.
System integrators must include the IC ID on the en d product.
3. Europe - EU Restricti ons
This equipment needs to be marked with the XXXX symbol and can be used
throughout the European community.
Marking by the symbol
Information to be supplied to the users:
802.11a Restrictions:
- This product is for indoor use only when using channels 36, 40, 44, 48, 52, 56, 60, or 64 (5150–
5350 MHz).
- DFS and TPC must remain enabled to ensure product compliance with EC regulations.
- To ensure compliance with local regulations, be sure to select the country in which the access
point is installed.
- This product can be used as shown in the table below:
5 GHz wireless LAN
IEEE 802.11a
indicates that usage restrictions apply.
Indoor Use
Only
A, AND, B, CH, D, CY, CZ,
DK, ES, EST, F, FIN, FL, FR,
GB, GR, H, I, IRL, IS, L, LT, M,
MC, N, NL, P, PL, RSM, S, SK,
SLO, V
Caution: Exposure to Radio Frequency Radiation.
To comply with RF exposure compliance requirements, for mobile configurations, a
separation distance of at least 20 cm must be maintained between the antenna of this
device and all persons.
Czech:
User's Manual in Czech language and a statement of conformity with Directive
1999/5/EC in Czech language must be enclosed to each product.
Page 4 of 7
OEM Installation Guidance Document
For 802.11bgn WLAN Module, SDGOB-1091
FCC ID: B94SDGOB1091; IC: 466D-SDGOB091
France:
2.4GHz for Metropolitan France:
In all Metropolitan départements, wireless LAN frequencies can be used under the
following conditions, either for public or private use:
· Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz
frequency band
· Outdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and
with maximum power (EIRP*) of 10 mW for the 2454-2483 MHz band
Note for system integrators:
- The module is tested to comply with the requirement of the R&TTE Directive. System
integrators are responsible for compliance of the final device with the R&TTE Directive.
- Packaging: CE Marking must also be on the outer packaging of the product. The outer
packaging must also provide an indication as to where the device is intended to be used
and OR conversely, where there may be restrictions for use.
4. Taiwan - NCC Statement to be included in the user gu ide
Article 12
Without permission, any company, firm or user shall not alter the frequency, increase the
power, or change the characteristics and functions of the original design of the certified
lower power frequency electric machine ry.
Article 14
Page 5 of 7
OEM Installation Guidance Document
For 802.11bgn WLAN Module, SDGOB-1091
FCC ID: B94SDGOB1091; IC: 466D-SDGOB091
The application of low power frequency electric machineries shall not affect the
navigation safety nor interfere a legal communication, if an interference is found, the
service will be suspended until improvement is made and the interference no longer
exists.
The foregoing legal communication refers to the wireless telecommunication operated
according to the telecommunications laws and regulations.
The low power frequency electric machinery should be able to tolerate the interference of
the electric wave radiation electric machineries and equipments for legal communications
or industrial and scientific applications.
Radio devices using 5.25-5.35 G Hz bands are restricted to indoor use only.
Appendix:
模組認證合格標簽 (ID):
“CCXXxxLPyyyZz"
如果使用本模組之平台,無法在外部看見審驗合格標籤時,應在該
平台的外部明顯標示
“內含射頻模組
5. Korea
Include the following statement either on the label or in the User Guide.
"당해 무선설비가 전파혼신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수
없음"
6. Argentina
The current approval is in the name of Broadcom’s local representative. It may be
necessary to obtain regulatory approval in the name of the local distributor or importer.
We suggest manufacturers chec k with their local distributors and importers in Argentina.
7. Brazil - Anatel
Before using Broadcom Anatel approvals,
CCXXxxLPyyyZz” .
Page 6 of 7
OEM Installation Guidance Document
For 802.11bgn WLAN Module, SDGOB-1091
FCC ID: B94SDGOB1091; IC: 466D-SDGOB091
1. PC- OEM must make arrangement for its local offices or distributors to provide
maintenance, technical assistance or replace any faulty products s old in Brazil.
2. All warranty services will be provided by the distributors or PC-OEM sales
support in Brazil. An official agreement stating warranty responsibilities must be
signed and made available to Broadcom.
Interference statement to be included in the Users Guide
"Este equipamento opera em caráter secundário, isto é, não tem direito a proteção
contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode
causar interferência a sistemas operando em caráter primário."
Translation:
"This equipment operates in secondary character. It can be affected by harmful
interference. However, it cannot cause interference to systems operating in primary
character."
8. South Africa – ICASA
PC-OEMs must make arrangement for importers to supply spare parts and carry out
repairs in South Africa.
9. Indonesia - POSTEL
PC-OEMs must make arrangement for importers to provide product warranty and after
sales services.
10. Japan – MIC
Radio devices using 5.25-5.35 G Hz bands are restricted to indoor use only.
Page 7 of 7
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.