Offline Diagnostics Environment Administrator's and User's Guide
HP Part Number: 5992-6605
Published: April 2009
Edition: 2
© Copyright 2009 Hewlett-Packard Development Company, L.P.
Confidential computersoftware. Valid license from HP required for possession, use or copying. Consistent with FAR 12.211 and 12.212, Commercial
Computer Software, Computer Software Documentation, and Technical Data for Commercial Items are licensed to the U.S. Government under
vendor's standard commercial license.
The informationcontained hereinis subject to change without notice. The only warranties for HP productsand servicesare setforth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP
shall not be liable for technical or editorial errors or omissions contained herein
Intel and Itanium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
Table of Contents
About This Document.........................................................................................................5
Intended Audience.................................................................................................................................5
New and Changed Information in This Edition.....................................................................................5
Document Organization.........................................................................................................................5
Typographic Conventions......................................................................................................................5
Related Information................................................................................................................................6
HP Encourages Your Comments............................................................................................................6
1 ODE Overview................................................................................................................7
Offline Diagnostics Environment...........................................................................................................7
ODE Limitations.....................................................................................................................................8
Support Plus Media for HP 9000 systems.........................................................................................8
2 Using ODE on Integrity Servers and Itanium Workstations.......................................9
ODE Tools Overview..............................................................................................................................9
Obtaining the Latest Version of ODE.....................................................................................................9
Ordering a CD...................................................................................................................................9
Downloading an Image to Create a CD..........................................................................................10
Running ODE........................................................................................................................................10
Running ODE from the HPSP.........................................................................................................10
Running ODE from the CD.............................................................................................................11
Non-ODE Tools on the CD..............................................................................................................11
3 Using ODE on HP 9000 Systems...............................................................................13
ODE Tools Overview............................................................................................................................13
Obtaining the Latest Version of ODE for HP 9000 Systems.................................................................14
Running ODE........................................................................................................................................14
Running ODE from the CD.............................................................................................................15
Running from the System Disk.......................................................................................................16
Determining Whether LIF-LOAD Is Installed...........................................................................16
Installing LIF-LOAD..................................................................................................................16
Running the ODE Tools..............................................................................................................17
4 Performing Common ODE Tasks................................................................................19
Running ODE Tools on Integrity Systems and Itanium Worksations..................................................19
Loading ODE and Running a Test Module.....................................................................................19
Running Multiple Test Modules......................................................................................................22
Error Detection................................................................................................................................24
Determining the Tools Supported by the Platform.........................................................................24
Entering Invalid Commands...........................................................................................................25
Running ODE Tools on HP 9000 Systems.............................................................................................25
Examining the Tools Suite...............................................................................................................25
Examining a Tool's Functions and Running the Tool......................................................................26
Using the makodiag Command......................................................................................................29
Using the diskexpt2 Command.......................................................................................................32
Index.................................................................................................................................37
Table of Contents 3
List of Examples
4-1 Loading ODE and Running a Test Module...................................................................................20
4-2 Running Multiple Test Modules....................................................................................................23
4-3 Error Detection..............................................................................................................................24
4-4 Using an Unsupported Tool..........................................................................................................25
4-5 Determining the System-Supported Tools....................................................................................25
4-6 Entering Invalid Commands.........................................................................................................25
4-7 Examining the Tools Suite.............................................................................................................26
4-8 Examining a Tool's Functions and Running the Tool....................................................................27
4-9 Using the makodiag Command....................................................................................................30
4-10 Using the diskexpt2 Command.....................................................................................................33
4 List of Examples
About This Document
The Offline Diagnostics Environment (ODE) provides a support tools platform that enables you
to troubleshoot a system that is running without an operating system. With the ODE you can
test systems that cannot be tested using the online tools.
Intended Audience
This document is intended for HP service and support personnel and system administrators
who manage the following systems:
• HP Integrity servers and workstations based on the Itanium® processor
• HP 9000 servers and workstations
Administrators are expected to have knowledge of operating system concepts, commands, and
configuration.
This document is not a tutorial.
New and Changed Information in This Edition
This is a new manual. Some of the information it contains came from the following documents
and supersedes those documents:
• ODE: Overview
• Overview Guide: Itanium Processor Family (IPF) Offline Diagnostics and Utilities CD
• Overview Guide: PA-RISC HP 9000 Offline Diagnostics Environment CD
• ODE: Frequently Asked Questions
Document Organization
This document is organized as follows:
Chapter 1 “ODE Overview” Provides an overview of the offline diagnostics
Chapter 2 “Using ODE on Integrity
Servers and Itanium Workstations”
Chapter 3 “Using ODE on HP 9000
Systems”
Chapter 4 “Performing Common
ODE Tasks”
Typographic Conventions
This document uses the following typographical conventions:
Command
Variable
Filename
User input
NOTE A note contains additional information to emphasize or supplement important
A command name or qualified command phrase.
The name of a placeholder in a command or other syntax display that you
replace with an actual value.
The name of a file or directory.
Commands and other text that you enter.
points of the main text.
environment.
Describes the ODE tools for the Integrity Systems and
Itanium workstations and tells you how to obtain and
install them.
Describes the ODE tools for HP 9000 systems and tells you
how to obtain and install them.
Provides examples of using ODE tools to perform common
tasks and how ODE reacts when it detects a problem.
Intended Audience 5
Related Information
The following Web sites can provide you with additional information about the ODE and system
diagnostics in general:
• For more information about diagnostic tools and concepts:
www.hp.com/go/hpux-diagnostics-docs
• To read about changes in the latest CD release:
www.hp.com/go/hpux-diagnostics-offline-docs
• To order the latest version of the ODE CD or to download an image from which you can
create your own CD:
www.software.hp.com
• For a suumary of how to use the ODE tools, a Quick Reference Guide is available in PDF format
at the following Web site:
www.hp.com/go/hpux-diagnostics-offline-docs
HP Encourages Your Comments
HP encourages your comments concerning this document. We are committed to providing
documentation that meets your needs. Send any errors found, suggestions for improvement, or
compliments to:
docsfeedback@hp.com
Include the document title, manufacturing part number, and any comments, errors found, or
suggestion for improvement you have concerning this document.
6
1 ODE Overview
This chapter provides information on the following topics:
• The purpose of ODE and when to use it.
• ODE limitations.
Offline Diagnostics Environment
The Offline Diagnostics Environment (ODE) provides a support tools platform that enables you
to troubleshoot a system that is running without an operating system.
With the ODE you can test systems that cannot be tested using online tools. The offline
environment is also useful for certain types of testing, such as when booting the system first is
undesirable, as is often the case with manufacturing applications.
ODE tools are available for troubleshooting problems on the Itanium processor family and on
HP 9000 systems (also referred to as PA-RISC systems). The way you use these tools is similar
on both types of platforms. The syntax and operation is the same; the primary differences are
the names of the tools and the way that ODE is launched. It does not depend on any operating
system.
The ODE provides two user interfaces:
• The command-line interface lets you select specific tests and utilities to execute on specific
hardware modules.
Use the command-line interface option if you are an advanced user and familiar with the
ODE. The command line interface allows you more control over the tests that you want to
conduct.
• The menu-driven interface, which is only available on 32-bit systems, lets you specify the
hardware module for the tests you want to run. ODE selects the appropriate tests to execute
on the specified module.
Use the menu-driven interface if you are unfamiliar with the command-line interface or
with ODE. When you select a module to test, the menu-driven interface is designed to choose
and then execute the appropriate tests for that module.
ODE has a distributed architecture that consists of several modules. Each module has a specific
function and uses well defined protocols to communicate with other modules. ODE includes the
following modules:
• Test Controller
Acts as a user interface and launches the execution of the Test Modules.
• Test Modules
Diagnostic or utility programs that execute within ODE.
These modules exercise or diagnose the user-specified hardware component or perform
operations such as downloading firmware. The test modules are provided for the following
components:
— Processor
— Memory
— Core electronic chipset
— Core I/O
— I/O cards
— Peripheral devices
• System Library (SysLib)
A set of common routines used by both the Test Controller and Test Modules.
Offline Diagnostics Environment 7
These routines perform functions such as I/O, string parsing, and system control.
The ODE tools are provided on CDs for Itanium systems (See “Obtaining the Latest Version of
ODE” (page 9)) and HP 9000 systems (See “Obtaining the Latest Version of ODE for HP 9000
Systems” (page 14)). You can order the CDs free or you can download the CD image and burn
your own CD.
ODE Limitations
The Offline Diagnostics Environment cannot be used on all systems and the way it is distributed
has recently changed for HP 9000 systems. The following sections describe these limitations.
V-Class Systems
Offline diagnostics on V-Class systems are different from offline diagnostics on all other HP
systems.
The offline diagnostics tools for V-Class systems are not supplied on the Offline Diagnostics and
Utilities CD. Instead, they are run from the V-Class Test Station. For procedures and details, see
the V-Class hardware documentation.
RX4610 and RX9610 systems
The Offline diagnostics tools for RX4610 and RX9610 systems systems are different from the ODE
diagnostics provided for other HP Integrity servers and Itanium-based workstations. For more
information, go to the following Web site:
www.hp.com/go/hpux-diagnostics-offline-docs
Support Plus Media for HP 9000 systems
ODE for HP 9000 systems was distributed on the Support Plus Media until the June 2005 release
(PA0506). Since the September 2005 release (PA0509), ODE is distributed only on the HP 9000
Offline Diagnostics Environment CD-ROM.
8 ODE Overview
2 Using ODE on Integrity Servers and Itanium Workstations
ODE tools for HP Integrity servers and HP workstations based on the Itanium processor are
distributed on the HP Integrity Servers and Itanium Workstations Offline Diagnostics and Utilities
CD-ROM. In addition to the ODE tools, the CD provides other utilities that are helpful in
identifying problems with your Integrity server or Itanium workstation.
This chapter describes the ODE tools for Integrity Systems and Itanium worksations and tells
you how to obtain and install them. See “Non-ODE Tools on the CD” for information about
non-ODE tools included on the CD. The following topics are discussed:
• An overview of the ODE tools for Integrity systems and Itanium workstations.
• How to obtain a CD containing the ODE or to create your own CD using an image
downloaded from the Web.
• How to run the ODE either from CD or from the HP Service Partition (HPSP).
ODE Tools Overview
The ODE tools are located in the \EFI\HP\DIAG\ODE directory on the CD. The following is a
partial list of the diagnostics and utilities provided under ODE. The complete list is documented
in the \EFI\HP\DIAG\DOCUMENTATION\Prod_Desc_All file on the CD.
CIODIAG2
CPUDIAG
DFDUTIL
FCFUPDATE
IODIAG
MAPPER
MEMDIAG
PCIUTIL
PERFVER
PLUTODIAG
Core I/O diagnostic tool
CPU diagnostic tool
Firmware update utilities for SCSI disks
Fibre Channel firmware update tool.
Diagnostic tool for HP Tachyon Fibre Channel board
Utility for mapping the physical layout of the SPU and its peripherals
Memory diagnostic tool
PCI HBA firmware update utility
Utility to run supported SCSI/IDE self-tests on devices
Diagnostic tool for Pluto and Mercury Core Electronics Complex (CEC)
Obtaining the Latest Version of ODE
The HP Integrity Servers and Itanium Workstations Offline Diagnostics and Utilities CD-ROM is
shipped with all Integrity systems and Itanium workstations. This CD is updated quarterly, at
which time new functions and features may be added, new hardware diagnostics may be
incorporated, and performance may be enhanced.
You can order a CD for free from the HP Software Depot Web page or you can download an
image of the CD to create your own CD. The following sections describe these alternatives.
To read about changes in the latest CD release, go to the following Web site:
www.hp.com/go/hpux-diagnostics-offline-docs
Ordering a CD
To order a CD free of charge from HP Software Depot, follow these steps:
1. Open a browser and navigate to the HP Software Depot Web main page:
http://www.software.hp.com
2. In the Search field, type ipf offline and click the search button (>>). The page displays
current and previous versions of the CD.
3. Select the appropriate version.
ODE Tools Overview 9
4. Click Receive for Free and follow the instructions to complete your order.
Downloading an Image to Create a CD
You can download a master .iso image file to create your own CD using your CD burner and
software.
The following steps describe how to download a Zip file that contains the image.
1. Open a browser and navigate to the HP Support and Drivers Web site:
http://welcome.hp.com/country/us/en/support.html
2. Under the section Select a product category, click Servers.
3. Select Integrity Servers and Integrity Blade Servers.
4. Select the desired server series.
5. Select the desired server product.
6. On the left pane of the screen, under the heading Tasks for my selected product, select
Download drivers and software.
7. Under Select operating system, select Cross operating system (BIOS, Firmware,
Diagnostics, etc.).
8. On the Download drivers and software page, go the Diagnostic section and select IPF
Offline Diagnostics and Utilities for the version you want to download.
9. Select the Release Notes tab. Read the Release Notes before downloading the CD image.
The Release Notes contain important instructions on downloading and producing an image
of the CD and other useful information such as platform information and revision history.
10. Select Obtain software. You will have to accept the license agreement to download the Zip
file.
11. Follow the instructions found in the Release Notes to create the CD.
Running ODE
You can run the ODE either from the CD or from the HP Service Partition (HPSP), a special disk
partition that is available when the operating system is not running. Determine which action is
best for you:
• Running ODE from the HPSP is considerably faster than running it from CD. On systems
that have an HPSP, you can copy the files to the partition from the CD by using a command
on the Launch menu (see “Running ODE from the HPSP”).
If your system does not have an HPSP, refer to your operating system user guide for
instructions on creating one.
• Run ODE from the CD if any of the following conditions exist:
— The hard disk is not functioning or is unavailable.
— The system does not support an HPSP.
— The HPSP does not have the latest version of the tools installed.
Running ODE from the HPSP
The following steps describe the procedure for running ODE from an HPSP.
1. Reset system power. The computer should come up to the Boot Manager menu.
2. See whether the HPSP is listed as one of the boot devices on the Boot Manager menu:
• If the HPSP appears as a boot device, move the cursor to the line that contains that
option and press Enter. The computer will boot to the Launch menu.
• If the HPSP does not appear as a boot device, verify that an HPSP exists on the system.
If the HPSP does not exist, you may have to create one. Refer to your operating system
10 Using ODE on Integrity Servers and Itanium Workstations
user guide for instructions on verifying and creating of the HPSP. When the partition
is created, copy the files from the CD. Follow these steps:
1. Boot from the CD to the Launch menu.
2. At the Launch menu, select the option for copying the contents of the CD to the
HPSP (Run CD Installer to install/update CD content to HPSP).
3. When you return tothe Boot Manager menu, an entry for the HPSPas a boot device
displays.
3. Start ODE by choosing the selection for ODE at the Launch menu.
Alternately, you can start ODE from the EFI prompt. To do this, change directories to \EFI\
HP\DIAG\ODE and enter the ODE command. For example:
fs2:> cd \EFI\HP\DIAG\ODE
fs2:\EFI\HP\DIAG\ODE> ODE
Running ODE from the CD
The following steps describe the procedure for running the HP Integrity Servers and Itanium
Workstations Offline Diagnostics and Utilities CD-ROM
1. Insert the CD into the CD drive and reboot. The system boots to the Boot Manager menu.
2. See whether the CD drive is listed as one of the boot devices on the Boot Manager menu:
• If the CD drive appears as a boot device, move the cursor to the line that contains it and
press the Enter key. The CD will boot to the Launch menu.
• If the CD drive does not appear as one of the boot devices, select the item on the Boot
Manager menu to add a boot device. Although this process can vary, the following
steps reflect a typical procedure:
1. Confirm that the CD is in the CD-ROM drive.
2. Select Boot Option Maintenance.
3. Select Add a Boot Option.
4. Select Removable Media Boot.
5. Answer the prompts.
NOTE: You can give any response to the Boot Option Data Type prompt.
6. Exit the menu, then exit the Boot Option maintenance menu. You return to the Boot
Manager menu.
7. Select CD drive as the boot device to boot from the CD to the Launch menu. After
configuring the CD drive as a boot device, you will not have to add it again on
subsequent boots.
3. Start ODE by choosing ODE on the Launch menu.
Alternately, you can start ODE from the EFI (Extensible Firmware Interface) prompt. To do
this, change directories to \EFI\HP\DIAG\ODE and enter the ode command. For example:
fs2:> cd \EFI\HP\DIAG\ODE
fs2:\EFI\HP\DIAG\ODE> ode
Non-ODE Tools on the CD
The HP Integrity Servers and Itanium Workstations Offline Diagnostics and Utilities CD-ROM also
provides a collection of non-ODE based diagnostic utilities. The following list describes several
of those utilities:
Launchmenu An application that allows the selection and execution of a set of
other applications available in a specific environment. It is available
in the \EFI\HP\TOOLS\LaunchMenu directory.
Running ODE 11
CD_Installer An application to update/install the diagnostics CD image to the
HP Service Partition (HPSP) of the disk running under EFI. It is
available in the \EFI\HP\TOOLS\CD_Installer directory.
MCA utilities A Machine Check Analyzer (MCA) Binary Logs gathering tool. It
is available in the \EFI\HP\TOOLS\MCA_Utilities directory.
Network utilities Utilities to diagnose network latency, communication, or
configuration issues. The following tools are available in the \EFI\
HP\TOOLS\Network directory:
ftp.efi
ifconfig.efi
inet.nsh
ping.efi
route.efi
tcpipv4.efi
I/O card utilities Diagnostics and firmware update utilities for various I/O cards.
Each supported card has its own utility and instruction set. A
complete list of the I/O cards diagnostics and utilities is available
in the \EFI\HP\DIAG\DOCUMENTATION\Prod_Desc_All
directory.
12 Using ODE on Integrity Servers and Itanium Workstations
3 Using ODE on HP 9000 Systems
The HP 9000 Offline Diagnostics Environment CD provides a comprehensive offline diagnostic
solution. The CD includes a suite of diagnostic tools that enable you to troubleshoot a system
troubleshoot a system on which HP-UX cannot be booted.
The ODE is also useful for some types of testing when it is not desirable to boot to the operating
system first, as is often the case in manufacturing environment.
This chapter describes the ODE tools for HP 9000 systems and tells you how to obtain and install
them. This chapter addresses the following topics:
• An overview of the ODE tools on HP 9000 systems.
• How to obtain a CD containing the ODE or to create your own CD using an image
downloaded from the Web.
• How to run the ODE either from CD or from the system disk using the Boot Logical
Interchange Format (LIF).
ODE Tools Overview
The following list provides an overview of ODE diagnostics and utilities that are available for
HP 9000 systems:
ASTRODIAG2*
CIODIAG*
COPYUTIL2
DFDUTIL2
DISKEXPT2*
DISKUTIL2
ESCDIAG*
IOTEST2
IKEDIAG2
MAKODIAG*
MAPPER2
MEM2*
MOABDIAG*
PACIODIAG*
PCIUTIL
PERFVER2
PLUTODIAG*
REODIAG*
TOGODIAG*
WDIAG*
An asterisk (*) indicates ODE tools that require a license. See the HP 9000 CD Overview Guide for
information on tools that require a license on 64-bit systems.
The Core Electronic Complex (CEC) diagnostic tool for ASTRO chip
The core I/O diagnostics tool for SD64A, SD32A, SD16A, rp7410, rp7420,
rp8410, and rp8420 systems
Utilities for creating copies and backups
Utilities for updating disk firmware
A utility for performing nondestructive tests on supported disks
Utilities for updating disk firmware
A CEC diagnostics tool for the sx2000
A diagnostics tool for I/O cards
A CEC diagnostics tool for the IKE chip
A CPU diagnostics tool for PA800 and PA8900 processors
A mappingutility for identifying anddisplaying system components, including
hardware modules and peripheral devices
A diagnostics utility for memory
A crossbar diagnostics tool for the sx2000
The core I/O diagnostics tool for rp3410, rp3440, rp4410, rp4440, and c8000
systems
Utility available only on 64–bit systems used for updating firmware, reading
Vital Product Data (VPD) and World Wide Number (WWN) of supported I/O
cards.
A utility for running self tests on supported devices
The Core Electronic Complex (CEC) diagnostics tool for the Zx1 chipset
A CEC diagnostics tool for the sx1000
A crossbar diagnostics tool for the sx1000
A CPU diagnostics tool for PCX-W processors
ODE Tools Overview 13
NOTE: HP provides different versions of the tools for 32–bit systems and 64-bit systems, such
as the N-Class systems. The 64-bit versions are indicated by having a “2” appended to the
program name. For example, the 64-bit version of MAPPER is MAPPER2.
Obtaining the Latest Version of ODE for HP 9000 Systems
The HP 9000 Offline Diagnostics Environment CD is shipped with all HP-UX systems. This CD is
updated as needed. New functions and features are added; new hardware diagnostics is
incorporated; and performance is enhanced periodically.
You can order a CD for free from the HP Software Depot Web page or you can download an
image of the CD to create your own CD.
The following steps list the procedure for ordering a free CD from HP Software Depot :
1. Open a browser and navigate to the HP Software Depot site main page:
http://www.software.hp.com
2. In the Search bar type pa offline and click the search button (>>). The page displays the
current and prior versions of the CD along with the Release Notes.
3. Review the list and select the appropriate version.
Read the Release Notes completely before downloading the CD image. The Release Notes
contain useful information such as platform information and revision history.
4. Click the Receive for Free button and follow the instructions to complete your order.
You can also download a master *.cdimage image file and create your own CD using your CD
burner and software.
NOTE: The *.cdimage is a large single file that must be renamed to *.iso before copying it
onto a CD-ROM. The *.cdimage is neither a collection of data files (compressed or
decompressed) nor an executable file (binary). In effect, you will download the CD image from
the Web site, rename the CD image and copy it onto a CD.
To read about changes offered in the latest CD release, go to the following Web site:
www.hp.com/go/hpux-diagnostics-offline-docs
Running ODE
You can run ODE in one of the following ways:
• Using the HP 9000 Offline Diagnostics Environment CD
• Using the Boot Logical Interchange Format (LIF) volume from the system disk
HP recommends that you run the offline diagnostics tools using the HP 9000 Offline ODE CD
for the following reasons:
• You can access the complete set of offline diagnostics tools.
• You can run ODE from the CD when the system is not booted to the operating system.
• You do not need a system disk to run ODE.
• You can run ODE on both HP 3000 (MPE/iX) systems and HP 9000 System (HP-UX).
• You can use the command-line interface or the menu-driven interface to run the tools on
32-bit systems.
If you do not have the HP 9000 Offline Diagnostics Environment CD, you can run the offline
diagnostics tools from the system disk. Before doing so, consider the following:
• The system disk contains only a subset of the most commonly used offline diagnostics tools:
— For 32-bit systems:
MAPPER
14 Using ODE on HP 9000 Systems
IOTEST
PERFVER
— For 64-bit systems:
MAPPER2
IOTEST2
PERFVER2
• You cannot use the menu-driven interface.
Running ODE from the CD
To run ODE, the system must be at the Boot Console Handler (BCH). When the system is
configured to boot to the operating system automatically, it waits 10 seconds for user intervention.
You can press any key to stop the autoboot process and go to the main menu prompt.
The following steps describe how to run ODE from the CD:
1. Insert the HP 9000 Offline Diagnostics Environment CD in the CD drive.
2. Restart the computer to boot to the PDC (Processor Dependent Code ) prompt.
NOTE: The appearance of PDC prompts may differ from one computer to another.
3. At the PDC prompt, enter the search command for a list of bootable devices. For example:
Main Menu: < Enter command or menu > search
IODC
Path# Device Path (dec) Device Path (mnem) Device Type Rev
----- ----------------- ------------------ ----------- ---P0 0/0/1/1.2 intscsib.2 Random access media 1
P1 0/0/2/0.2 intscsia.2 Random access media 1
4. Select the CD-ROM device and boot from that device:
Main Menu: < Enter command or menu > boot P1
5. When prompted, answer y (yes) to interact with the Initial Program Loader (IPL):
Interact with IPL (Y, N, or Cancel)? y
This will return the ISL> prompt.
6. At the ISL prompt, enter the ode command to run the ODE program:
ISL> ode
This will return the ODE> prompt.
7. At the ODE prompt, enter the ls command to obtain a list of the offline diagnostics tools:
ODE> ls
Modules on this boot media are:
filename type size created description
----------------------------------------------------------------------------MAPPER2 TM 146 05/07/12 64 bit version of the system mapping
IOTEST2 TM 882 05/07/12 64 bit version that runs ROM-based self
PERFVER2 TM 126 05/07/12 64 bit version that runs ROM-based self
8. To select and run the ODE tools, enter the run command and the name of the module you
want to run. For example:
ODE> run mapper2
Running ODE 15
IMPORTANT: You must restart the system after running any ODE module before booting to
the operating system or running any non-ODE utility.
Running from the System Disk
To run the offline diagnostics tools from the system disk, you must install the LIF-LOAD to the
boot area of the system disk from the HP 9000 Offline Diagnostics Environment CD.
LIF is a subset of the offline diagnostics tools for HP 9000 systems. After LIF is installed, you can
boot the system disk to the ISL prompt, run the ODE program, and then launch the offline
diagnostics tools from the ODE prompt.
The following sections tell you how to determine whether LIF-LOAD is installed on the system
disk, how to install LIF-LOAD on a HP 9000 system, and how to boot from the LIF volume.
NOTE: Prior to September 2005 the LIF volume was a part of the Support Plus Media. Since
then, it is available only on the HP 9000 Offline Diagnostics Environment CD.
Determining Whether LIF-LOAD Is Installed
Complete the following procedure to check if LIF-LOAD is installed on the system disk:
1. Restart the computer to boot to the PDC prompt.
NOTE: PDC prompts may differ from one system to another.
2. At the PDC prompt, boot from the primary boot path:
Main Menu: Enter command or menu > boot primary
3. When prompted, answer yes to interact with the IPL:
Interact with IPL (Y, N, or Cancel)? y
This will return the ISL> prompt.
4. Enter the ls command at the ISL prompt:
ISL> ls
If ls returns ODE in its display list, LIF-LOAD is installed on the system. If it is not installed,
see “Installing LIF-LOAD.”
Installing LIF-LOAD
Complete the following procedure for installing the LIF-LOAD product to the boot area of the
system disk:
1. Boot the system to HP-UX.
2. Log in as root.
3. Load the HP 9000 Offline Diagnostics Environment CD to the CD drive.
4. Make a directory from root (/) as a mount point. For example:
# mkdir /Offline_CD
5. Enter the ioscan -fnCdisk command to find the block special device file for the CD
drive. In the following example the block special device file for the CD is /dev/dsk/c0t0d0:
# ioscan -fnCdisk
Class I H/W Path Driver S/W State H/W Type Description
disk 0 10/0/14/0.0.0 sdisk CLAIMED DEVICE TEAC CD-532E-B
/dev/dsk/c0t0d0 /dev/rdsk/c0t0d0
disk 1 10/0/15/1.4.0 sdisk CLAIMED DEVICE SEAGATE ST39204LC
/dev/dsk/c3t4d0 /dev/rdsk/c3t4d0
16 Using ODE on HP 9000 Systems
6. Mount the CD using the CD block special device file and the directory you created in step
4. For example:
# mount /dev/dsk/c0t0d0 /Offline_CD
7. Run the following script from the CD mount directory:
# /Offline_CD/DOCS/install_lifload.ksh
Running the ODE Tools
The following steps describe the procedure to run ODE from the system disk:
1. Boot the system from the PDC prompt.
2. Enter the following command:
>> boot primary
3. When prompted, answer y (yes) to interact with the IPL:
Interact with IPL (Y, N, or Cancel)? y
4. At the ISL prompt, enter the ode command to run the ODE program:
ISL> ode
5. Enter the ls command at the ODE prompt to obtain a list of the offline diagnostics tools:
ODE> ls
The screen displays a list of the tools.
6. To select and run the tools, enter the run command and the name of the module you want
to run. For example:
ODE> run mapper2
Running ODE 17
18
4 Performing Common ODE Tasks
This chapter shows how to use ODE tools to perform common tasks and lets you see how ODE
reacts when detecting a problem.
The offline diagnostics tools that run on Integrity Systems and Itanium worksations and on HP
9000 systems are similar in syntax and functions; the primary differences are in the names of the
tools and the way they are launched. Keep this in mind as you review the examples in the
following sections. The output in either section will be similar to what you will see, regardless
of which system you are diagnosing.
Running ODE Tools on Integrity Systems and Itanium Worksations
This section shows the output of tools run on Integrity Systems and Itanium worksations systems.
The complementary tools for HP 9000 systems will produce similar results. The following
examples are provided:
• Loading and running a test module.
• Using the two test modules together.
• Viewing an error detected by a test module.
• Obtaining a list of the tools supported by your platform.
• Examples that show the ODE output for various invalid commands.
Loading ODE and Running a Test Module
The example in this section shows the following information:
• The ODE startup banner
• Running the test module cpudiag for the first time.
• Running cpudiag for a second time (the banner information is not displayed).
• Running the cpudiag help command
• Setting and using environmental variables.
• Exiting cpudiag and ODE
Running ODE Tools on Integrity Systems and Itanium Worksations 19
Example 4-1 Loading ODE and Running a Test Module
fs0:\EFI\HP\DIAG\ODE>ode
***********************************************************************
****** ******
****** OFFLINE DIAGNOSTIC ENVIRONMENT ******
****** ******
****** (C) Copyright Hewlett-Packard Co 2006 ******
****** All Rights Reserved ******
****** ******
****** ******
****** TC Version XX.XX.XX ******
****** SysLib Version XX.XX.XX ******
****** ******
****** ******
***********************************************************************
Type HELP for command information.
ODE> run cpudiag
***********************************************************************
****** ******
****** CPUDIAG ******
****** ******
****** (C) Copyright Hewlett-Packard Co 2006 ******
****** All Rights Reserved ******
****** ******
****** This program may only be used by HP support personnel and ******
****** those customers with the appropriate Class license or ******
****** Node license for systems specified by the license. HP ******
****** shall not be liable for any damages resulting from misuse ******
****** or unauthorized use of this program. This program ******
****** remains the property of HP. ******
****** ******
****** Version XX.XX.XX ******
****** ******
***********************************************************************
Type HELP for command information.
STARTING EXECUTION OF CPUDIAG
SECTION 001
SECTION 002
SECTION 003
END OF LOOP 1.
RUN COMPLETED.
ODE> cpudiag
CPUDIAG> help
CPUDIAG Help
Commands
--------
DIAGINFO -- Display information about LDIAG
SECTION -- Sets/Displays current test sections to execute
UP -- Test only one processor (the BSP)
MP -- Test all processors in the system
SEED -- Sets the default seed value to be used
PROC -- Selects which processors to test
PSTAT -- Displays information on processors to test
BREAK -- Sets breakpoints in diagnostic
MASTER -- Selects which cpu will play the master role in the
Multi-processor tests
20 Performing Common ODE Tasks
CREG -- Displays selected control and application registers
ODE Commands Available from CPUDIAG
Basic Commands
-------------HELP -- Prints detailed information to the screen, when
"help command" or "help var" is typed
LS -- List modules available on boot medium
Module_Name -- Load and initialize a module by typing its name
(For more help, type "help module_name")
RUN -- Run a module (after setting desired environment variables)
Control-Y|Control-C -- Abort an ODE command; pause a module run
RESUME -- Restart a paused module
DISPLOG -- After running a module, display contents of a log
EXIT -- Return to next higher level prompt
Environmental Variables
----------------------SHOWSTATE -- Display the value of the following environment variables:
LOOP -- Run a test this many times
ERRPRINT [ON|OFF] -- Print low-level error messages to console
(primarily for manufacturing use)
ERRNUM [ON|OFF] -- Print one-line, numbered errors to the console
ERRPAUSE [ON|OFF] -- Pause module upon error detection
ERRONLY [ON|OFF] -- Print ONLY error messages; disable non-error
and isolation message printing
INFOPRINT [ON|OFF] -- Print informational messages to the console
ISOPRINT [ON|OFF] -- Print fault isolation messages to the
console
ISOPAUSE [ON|OFF] -- Pause module when isolation message is
generated
LOGSIZE -- Set the size of a message log
DEFAULT -- Reset environment variables to default state
CPUDIAG> help section cr
SECTION {integer: 0..3 | integer integer | integer/integer |
[integer] [integer/integer] }. This command sets a 4 bit logical
integer bit mask. Each bit corresponds to a test section in the
diagnostic. For each bit that is set a test section is executed.
Examples: SECTION 3 sets bit three and clears all other bits. SECTION
1 3 sets bits one and three and clears all other bits. SECTION 1/3 is
equivalent to SECTION 1 2 3.
CPUDIAG> section 2
CPUDIAG> loop 2
CPUDIAG> run cr
STARTING EXECUTION OF CPUDIAG
SECTION 002
END OF LOOP 1.
STARTING EXECUTION OF CPUDIAG
SECTION 002
END OF LOOP 2.
RUN COMPLETED.
CPUDIAG> exit
ODE> exit
fs0:\efi\diag>
Running ODE Tools on Integrity Systems and Itanium Worksations 21
Running Multiple Test Modules
The example in this section shows two test modules, cpudiag and memdiag , being run.
22 Performing Common ODE Tasks
Example 4-2 Running Multiple Test Modules
ODE> loop 2;run cpudiag memdiag
***********************************************************************
****** ******
****** CPUDIAG ******
****** ******
****** (C) Copyright Hewlett-Packard Co 2006 ******
****** All Rights Reserved ******
****** *****
****** This program may only be used by HP support personnel and ******
****** those customers with the appropriate Class license or ******
****** Node license for systems specified by the license. HP ******
****** shall not be liable for any damages resulting from misuse ******
****** or unauthorized use of this program. This program ******
****** remains the property of HP. ******
****** ******
****** Version XX.XX.XX ******
****** ******
***********************************************************************
Type HELP for command information.
STARTING EXECUTION OF CPUDIAG
SECTION 001
SECTION 002
SECTION 003
***********************************************************************
****** ******
****** MEMDIAG ******
****** ******
****** (C) Copyright Hewlett-Packard Co 2006 ******
****** All Rights Reserved ******
****** ******
****** This program may only be used by HP support personnel and ******
****** those customers with the appropriate Class license or ******
****** Node license for systems specified by the license. HP ******
****** shall not be liable for any damages resulting from misuse ******
****** or unauthorized use of this program. This program ******
****** remains the property of HP. ******
****** ******
****** Version XX.XX.XX ******
****** ******
***********************************************************************
Type HELP for command information.
STARTING EXECUTION OF MEMDIAG
SECTION 001
SECTION 002
SECTION 003
END OF LOOP 1.
STARTING EXECUTION OF CPUDIAG
SECTION 001
SECTION 002
SECTION 003
STARTING EXECUTION OF MEMDIAG
SECTION 001
SECTION 002
SECTION 003
Running ODE Tools on Integrity Systems and Itanium Worksations 23
END OF LOOP 2.
RUN COMPLETED.
ODE> exit
fs0:\efi\diag>
Error Detection
The following example shows an error detected by the test module cpudiag. In the example,
ERRPRINT is on, ERRPAUSE is on, and cpudiag implements a command that dumps the state
of the general registers (REGISTER). This example begins with only ODE loaded. Notice the
changes in the command prompt:
Example 4-3 Error Detection
ODE> run cpudiag
***********************************************************************
****** ******
****** CPUDIAG ******
****** ******
****** (C) Copyright Hewlett-Packard Co 2006 ******
****** All Rights Reserved ******
****** ******
****** This program may only be used by HP support personnel and ******
****** those customers with the appropriate Class license or ******
****** Node license for systems specified by the license. HP ******
****** shall not be liable for any damages resulting from misuse ******
****** or unauthorized use of this program. This program ******
****** remains the property of HP. ******
****** ******
****** Version XX.XX.XX ******
****** ******
***********************************************************************
Type HELP for command information.
STARTING EXECUTION OF CPUDIAG
SECTION 001
ERROR 002 DETECTED IN SECTION 001 WHILE TESTING THE CPU
General register 8 was 0x555555a5 should be 0x55555555.
CPUDIAG PAUSED> proc
CPUDIAG PAUSED> resume
SECTION 002
SECTION 003
CPUDIAG DETECTED 1 HARDWARE ERROR
END OF LOOP 1.
RUN COMPLETED
ODE>
Determining the Tools Supported by the Platform
Some ODE tools cannot be used on all platforms. Attempting to use an unsupported tool will
generate an error message. For example:
24 Performing Common ODE Tasks
Example 4-4 Using an Unsupported Tool
ODE> WDIAG
The Hversion = 88c0. The Sversion = 491. UUT_MODEL = 88c
--------------------------------------------------------------------WARNING: THIS PROCESSOR MODEL 88c IS INCOMPATIBLE WITH THIS DIAGNOSTIC.
---------------------------------------------------------------------
FATAL SOFTWARE ERROR !!
EXECUTION OF WDIAG MAY PRODUCE UNDEFINED RESULTS
ERROR: Initialization of WDIAG failed
If you are uncertain about which tools you can use on your system, specify the ls command at
the ODE prompt to obtain information about the tools your system supports. For example:
Example 4-5 Determining the System-Supported Tools
ODE> ls
Modules on this boot media are:
filename type size created description
----------------------------------------------------------------------------README2 TM 345 06/03/14 64 bit version that displays README file
MAPPER2 TM 800 06/03/14 64 bit version of the system mapping utility
MEM2 TM 1604 06/03/14 64 bit Memory diagnostic
MAKODIAG TM 9601 06/03/14 CPU diagnostic for PA8800 processors
PCIUTIL TM 942 06/03/14 PCI HBA Firmware Update Utility
Entering Invalid Commands
Common errors such as specifying an unknown command, a misspelled command, or an
inaccurate parameter will cause ODE to generate error messages. Example 4-6 shows three such
errors.
Example 4-6 Entering Invalid Commands
ODE> loadd
INVALID COMMAND: COMMAND = LOADD
ODE> load
MISSING PARAMETER: COMMAND = LOAD
ODE> load !4
INVALID PARAMETER: COMMAND = LOAD !4
Running ODE Tools on HP 9000 Systems
This section shows the output of tools run on HP 9000 systems. The complementary tools for
Integrity Systems and Itanium worksations will produce similar results. The following examples
are provided:
• Examining the tools suite
• Examining a tool's functions and running the tool
• Using the makodiag command
• Using the diskexpt2 command
Examining the Tools Suite
The following example shows the initiation of an ODE session and using the ls command to
display the installed tools on a 64-bit system:
Running ODE Tools on HP 9000 Systems 25
Example 4-7 Examining the Tools Suite
ISL> ode
Loading....
***************************************************************************
****** ******
****** Offline Diagnostic Environment ******
****** ******
****** (C) Copyright Hewlett-Packard Co 1993-2006 ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting from the ******
****** use of this program. ******
****** ******
****** TC Version A.02.27 ******
****** SysLib Version A.00.78 ******
****** Loader Version A.00.62 ******
****** Mapfile Version A.01.67 ******
****** ******
***************************************************************************
Type HELP for command information.
ODE> ls
Modules on this boot media are:
filename type size created description
-----------------------------------------------------------------------------
README2 TM 345 06/03/14 64 bit version that displays README fil
MAPPER2 TM 800 06/03/14 64 bit version of the system mapping ut
MEM2 TM 1604 06/03/14 64 bit Memory diagnostic
AR60DIAG2 TM 3117 06/03/14 Fibre Channel 60 disk array utility (64
ARDIAG2 TM 3731 06/03/14 64 bit version of the ICE & ICICLE disk
COPYUTIL2 TM 2131 06/03/14 64 bit version of the Disk-to-tape copy
DFDUTIL2 TM 1729 06/03/14 64 bit version of the Disk firmware dow
DISKEXPT2 TM 1655 06/03/14 64 bit version of the expert disk utili
DISKUTIL2 TM 1553 06/03/14 64 bit version of the nondestructive di
MAKODIAG TM 9601 06/03/14 CPU diagnostic for PA8800 processors
NIKEARRY2 TM 1843 06/03/14 Nike disk array utility
PACIODIAG TM 3895 06/03/14 Core IO diagnostic
PCIUTIL TM 942 06/03/14 PCI HBA Firmware Update Utility
PLUTODIAG TM 3878 06/03/14 PLUTO IO Controller diagnostic
VADIAG2 TM 4787 06/03/14 hp StorageWorks Virtual Array Utility
IOTEST2 TM 4675 06/03/14 64 bit version that runs ROM-based self
PERFVER2 TM 2343 06/03/14 64 bit version that runs ROM-based self
Examining a Tool's Functions and Running the Tool
The following example examines the functions of a tool using the help command and then
running the command.
26 Performing Common ODE Tasks
Example 4-8 Examining a Tool's Functions and Running the Tool
ODE> mapper2
***************************************************************************
****** ******
****** MAPPER2 ******
****** ******
****** Copyright (C) 2003-2006 by Hewlett-Packard Company ******
****** All Rights Reserved ******
****** ******
****** HP shall not be liable for any damages resulting from the ******
****** use of this program. ******
****** ******
****** Version B.01.02 ******
****** ******
***************************************************************************
Type HELP for command information.
MAPPER2 Help
Commands
------- UTILINFO -- Display information about MAPPER
Continue ([y]/n)? y
ODE Commands Available from MAPPER2
Basic Commands
------------- HELP -- Prints detailed information to the screen, when "help" <command>
or "help" <var> is typed
LS -- List modules available on boot medium
RUN -- Run a module (after setting desired environment variables)
Control-Y|Control-C -- Abort an ODE command; pause a module run
RESUME -- Restart a paused module
DISPLOG -- After running a module, display contents of a log
EXIT -- Return to next higher level prompt
Environmental Variables
---------------------- SHOWSTATE -- Display the value of the following environment variables:
LOOP -- Run a test this many times
ERRPRINT [ON|OFF] -- Print low-level error messages to console
(primarily for manufacturing use)
ERRNUM [ON|OFF] -- Print one-line, numbered errors to the console
Continue ([y]/n)? y
ERRPAUSE [ON|OFF] -- Pause module upon error detection
ERRONLY [ON|OFF] -- Print ONLY error messages; disable non-error
and isolation message printing
INFOPRINT [ON|OFF] -- Print informational messages to the console
ISOPRINT [ON|OFF] -- Print fault isolation messages to the console
ISOPAUSE [ON|OFF] -- Pause module when isolation message is generated
LOGSIZE -- Set the size of a message log
DEFAULT -- Reset environment variables to default state
MAPPER2> help utilinfo
UTILINFO
Use this command to display information about the MAPPER utility.
MAPPER2> utilinfo
MAPPER is an ODE-based utility program. It is intended to display the configuration of an HPPA system. This includes the path, identification, and
revision information of HPPA modules and peripheral devices. HPPA modules
include Processors, Memory Controllers, and I/O Modules (such as bus con-
Running ODE Tools on HP 9000 Systems 27
verters, channel adapters, device adapters, and interface cards). Processor
Hardware Model, Hardware ID, Processor Board Component revisions, Cache and
TLB sizes, and Co-processor information are displayed as well. HPPA system
Software Model, Software ID, Software Capabilities, and Model Strings are
also shown.
MAPPER2> run
STARTING EXECUTION OF MAPPER2
Processor Identification:
Hardware Model: 884H, Revision: 0
Software Model: 4H, Revision: 0
Hardware ID: 0, Software ID: 2842435972 (unsigned decimal)
HP-UX Model String: 9000/800/rp4440
Processor Board Revisions:
CPU - CPU Chip: 257
PDC - Processor Dependent Code: 45.11
Cache and TLB Sizes:
Instruction Cache: 3276 K bytes, Instruction TLB: 240 entries
Data Cache: 3276 K bytes, Data TLB: 240 entries
Co-processors:
Floating Point Co-processor(s) installed
Configuring the System...
I/O Configuration:
Type HW SW Revisions
Path Component Name ID Model Model Hdwr Firm
---------- ----------------------------------- ----- ----- ----- ----- -----
0 Pluto I/O BC McKinley Port CH 880H CH 0 0
0/0 Mercury PCI Bridge DH 783H AH 0 0
0/0/1/0 Communications Controller 103CH 1290H 103CH 1291H 01H
0/0/1/1 Serial Controller 103CH 1048H 103CH 1282H 03H
0/0/2/0 USB Controller 1033H 0035H 1033H 0035H 41H
0/0/2/1 USB Controller 1033H 0035H 1033H 0035H 41H
0/0/3/0 IDE Controller 1095H 0649H 1095H 0649H 02H
0/0/3/0.0.0.0
DV-28E-B - - - -
0/1 Mercury PCI Bridge DH 783H AH 0 0
0/1/1/0 Symbios SCSI Ultra160 LVD HBA 1000H 0021H 103CH 1340H 01H
0/1/1/0.1.0
HP 36.4G ST336753LC - - - - HPC3
0/1/1/0.4.0
HP SAFTE - - - - 1
0/1/1/1 Symbios SCSI Ultra160 LVD HBA 1000H 0021H 103CH 1340H 01H
0/1/1/1.0.0
HP 36.4G ST336753LC - - - - HPC3
0/1/1/1.4.0
HP SAFTE - - - - 1
0/1/2/0 Ethernet Controller 14E4H 1645H 103CH 128AH 15H
0/2 Mercury PCI Bridge DH 783H AH 0 0
0/2/1/0 HP A7143A 4 Port Ultra160 RAID HBA 0E11H B060H 0E11H 4070H 02H
0/4 Mercury PCI Bridge DH 783H AH 0 0
0/4/1/0 PCI->PCI Bridge 1014H 01A7H 0000H 0000H 03H
0/4/1/0/4/0
HP A9784A 2Gb FC/GigE Combo Adapter 1077H 2312H 103CH 12C7H 03H
0/4/1/0/6/0
HP A9784A 1000Base-T FC/GigE Combo 14E4H 16C7H 103CH 12CAH 10H
0/4/2/0 HP A7011A 1000Base-SX Dual Port HBA 8086H 107AH 103CH 12A8H 03H
0/4/2/1 HP A7011A 1000Base-SX Dual Port HBA 8086H 107AH 103CH 12A8H 03H
0/5 Mercury PCI Bridge DH 783H AH 0 0
0/5/2/0 Fibre Channel Controller 10DFH F980H 10DFH F980H 01H
0/6 Mercury PCI Bridge DH 783H AH 0 0
0/6/1/0 PCI->PCI Bridge 8086H B154H 0000H 0000H 00H
0/6/1/0/4/0
Ethernet Controller 1011H 0019H 103CH 125AH 41H
0/6/1/0/5/0
Ethernet Controller 1011H 0019H 103CH 125AH 41H
0/6/1/0/6/0
Ethernet Controller 1011H 0019H 103CH 125AH 41H
0/6/1/0/7/0
28 Performing Common ODE Tasks
Ethernet Controller 1011H 0019H 103CH 125AH 41H
8 Memory Controller (4 Gbytes) 1H AFH 9H 0 0
Slot 0/0a 256MB
Slot 0/0b 256MB
Slot 0/0c 256MB
Slot 0/0d 256MB
Slot 0/1a 256MB
Slot 0/1b 256MB
Slot 0/1c 256MB
Slot 0/1d 256MB
Slot 0/2a --
Slot 0/2b --
Slot 0/2c --
Slot 0/2d --
Slot 0/3a 512MB
Slot 0/3b 512MB
Slot 0/3c 512MB
Slot 0/3d 512MB
16 Management Controller FH 4H C0H 0 0
128 Processor 0H 884H 4H 0 0
129 Processor 0H 884H 4H 0 0
RUN COMPLETED.
MAPPER2> ex
Resetting the Boot Device...
Done.
Exiting...
Using the makodiag Command
The following example output from the makodiag command. The vertical ellipses represent
output that was removed from this example to make it shorter.
Running ODE Tools on HP 9000 Systems 29
Example 4-9 Using the makodiag Command
ODE> makodiag; run; ex
The Hversion = 8840. The Sversion = 491. UUT_MODEL = 884
***************************************************************************
****** ******
****** MAKODIAG ******
****** ******
****** Copyright (C) 2006 by Hewlett-Packard Company ******
****** All Rights Reserved ******
****** ******
****** This program may only be used by HP support personnel and ******
****** those customers with the appropriate Class license or ******
****** Node license for systems specified by the license. HP ******
****** shall not be liable for any damages resulting from misuse ******
****** or unauthorized use of this program. This program ******
****** remains the property of HP. ******
****** ******
****** Version B.00.33 ******
****** ******
***************************************************************************
Type DIAGINFO for test information.
Enter password or a <cr> to exit:
Type HELP for command information.
Found 2 processors
STARTING EXECUTION OF MAKODIAG
SECTION 00
.
.
.
SECTION 006
STARTING BUS INTERFACE DATA PATH TESTS - SECTIONS 7/10
SECTION 007
SECTION 008
SECTION 009
SECTION 010
STARTING CACHE DATA PATH TESTS - SECTIONS 11/25
SECTION 011
SECTION 012
SECTION 013
................................
SECTION 14
<Test Skipped>
SECTION 16
.
.
.
30 Performing Common ODE Tasks
STARTING CPU INSTRUCTION TESTS - SECTIONS 35/86
SECTION 035
.
.
.
SECTION 086
STARTING CPU EXTENDED TESTS - SECTIONS 87/100
SECTION 087
.
.
.
SECTION 100
STARTING FLOATING POINT TESTS - SECTIONS 102/134
SECTION 102
.
.
.
SECTION 134
<<<MASTER = 1 SLAVE = 0>>>
STARTING MULTIPLE PROCESSOR TESTS - SECTIONS 140/149
SECTION 140
Set up for LDW/STW (line test) test
Testing the LDW/STW instructions (line test) - syncronously
Checking ownership of blocks, and LDW/STW times
Set up for LDW/STW (word test) test
Testing the LDW/STW instructions (word test) -- syncronously
Checking ownership of blocks, and LDW/STW times
SECTION 141
Functional test of PDTLB instruction
SECTION 142
Functional test of PITLB instruction
SECTION 143
PDTLB head on interface test
SECTION 144
PITLB head on interface test
SECTION 145
LOAD/STORE instructions test (virtual mode)
Set up for virtual mode LDW/STW test
Testing the LDW/STW instructions
Testing the LDWM/STWM instructions
Testing the LDWX/STW instructions
Testing the LDH/STH instructions
Running ODE Tools on HP 9000 Systems 31
Testing the LDB/STB instructions
Testing the STW/LDCWS instructions
Testing the STD/LDD instructions
SECTION 146
Functional test of FIC instruction
<<<MASTER = 1 SLAVE = 0>>>
STARTING MULTIPLE PROCESSOR TESTS - SECTIONS 140/149
SECTION 140
Set up for LDW/STW (line test) test
Testing the LDW/STW instructions (line test) - syncronously
Checking ownership of blocks, and LDW/STW times
Set up for LDW/STW (word test) test
Testing the LDW/STW instructions (word test) -- syncronously
Checking ownership of blocks, and LDW/STW times
SECTION 141
Functional test of PDTLB instruction
SECTION 142
Functional test of PITLB instruction
SECTION 143
PDTLB head on interface test
SECTION 144
PITLB head on interface test
SECTION 145
LOAD/STORE instructions test (virtual mode)
Set up for virtual mode LDW/STW test
Testing the LDW/STW instructions
Testing the LDWM/STWM instructions
Testing the LDWX/STW instructions
Testing the LDH/STH instructions
Testing the LDB/STB instructions
Testing the STW/LDCWS instructions
Testing the STD/LDD instructions
SECTION 146
Functional test of FIC instruction
RUN COMPLETED.
Wait 7 seconds for processors to return to ready state.
Using the diskexpt2 Command
The following example shows the output from the diskexpt2 command. Note the restrictions
on using this command and the required use of a password.
32 Performing Common ODE Tasks
Example 4-10 Using the diskexpt2 Command
ODE> diskexpt2
Type HELP for command information.
***************************************************************************
****** ******
****** DISKEXPT2 ******
****** ******
****** Copyright (C) Hewlett-Packard Co. 1998 thru 2006 ******
****** All Rights Reserved ******
****** ******
****** This program may only be used by HP support personnel and ******
****** those customers with the appropriate Class license or ******
****** Node license for systems specified by the license. HP ******
****** shall not be liable for any damages resulting from misuse ******
****** or unauthorized use of this program. This program ******
****** remains the property of HP. ******
****** ******
****** Version B.00.27 ******
****** ******
***************************************************************************
Enter password or a <cr> to exit:
The bus is being scanned for devices. Please wait.
More than 3 Modules/Busses were found on this system.
Since mapping all the Busses will take time, you can
choose a range of busses to map or press <return> to
map all the busses. For example, to map bus 2, 4, 5,
and 6, type the range 2,4/6
Indx Path Module Bus HPA SPA
---- --------------- ---------- ------ -------- -------0 0/1/1/0 PCI SCSI SCSI 200800 0
1 0/1/1/1 PCI SCSI SCSI 200900 0
2 0/2/1/0 PCI RAID160 SCSI 400800 0
3 0/4/1/0/4/0 PCI FCQL Fibre 812000 0
Enter a range (? for help, q for quit)<default is map all>:
The bus is being scanned for devices. Please wait.
Sel/
Indx Path Product String Rev Bus Size
---- --------------------- ----------------------------------- ------ ------ ----- 0 0/1/1/0.1.0 HP 36.4G ST336753LC HPC3 SCSI 36.4 GB
1 0/1/1/1.0.0 HP 36.4G ST336753LC HPC3 SCSI 36.4 GB
Legend:
Sel/Indx - Indx of the disk listed. This is flagged with a '*'
if it is marked for testing.
NOTE:
The size of disk may not match the Information Specified by
the vendor due to difference in calculation methods.
DISKEXPT2> help
DISKEXPT2 Help
------------------------------------------------------------------------------Quick Start on Utility.
--------------------UTILINFO A brief procedure on how to use the utility.
Environment variables:
--------------------SHOWENV Displays the current settings for TESTDISK, BLOCK and RANGE.
BLOCK Selects the block to be tested.
RANGE Selects range of blocks to be tested by the ROMT and WRTMT commands.
TESTDISK Selects the disk to be tested.
Read & Writing Disk Blocks:
-------------------------SHOWBUF Displays the internal buffer contents after the last read command.
READBLK Reads the given block from the given SCSI disk.
READFULL Reads the given block with the header from the given SCSI disk.
WRITEBLK Writes the given block on to the given disk.
WRITEFULL Writes the given block with the header on to the given disk.
Media Tests:
----------ROMT Performs a read media test on the selected range of blocks.
WRTMT Performs a write/read/verify test on the selected range of blocks.
Continue ([y]/n)? y
------------------------------------------------------------------------------Disk Log Access:
--------------ACCESSLOG Displays the disk logs in a consise format.
READLOG Reads the log data from the disk.
CLRLOG Clears the log data from the disk.
Running ODE Tools on HP 9000 Systems 33
Reassigning Block:
-----------------
SPARE Reassigns the given block on the disk.
Gathering Disk Information:
--------------------------
DISPMAP Displays a list of all the disks found with their present settings.
DISKINFO Displays the contents of SCSI Inquiry Command for SCSI and Describe
Command for FLEX and CS80 devices.
INQUIRY Use DISKINFO command.
DESCRIBE Use DISKINFO command.
MODESENSE Get mode sense information from SCSI devices only.
Add a Disk Manually:
-------------------
ADDDISK Allows the user to add non-responding disks to the mapped list of
disks.
-------------------------------------------------------------------------------
Continue ([y]/n)? y
ODE Commands Available from DISKEXPT2
Basic Commands
--------------
HELP -- Prints detailed information to the screen, when "help <command>" or "help <var>" is typed
LS -- List modules available on boot medium
RUN -- Run a module (after setting desired environment variables)
Control-Y|Control-C -- Abort an ODE command; pause a module run
RESUME -- Restart a paused module
DISPLOG -- After running a module, display contents of a log
EXIT -- Return to next higher level prompt
Environmental Variables
-----------------------
SHOWSTATE -- Display the value of the following environment variables:
LOOP -- Run a test this many times
ERRPRINT [ON|OFF] -- Print low-level error messages to console
(primarily for manufacturing use)
ERRNUM [ON|OFF] -- Print one-line, numbered errors to the console
Continue ([y]/n)? n
DISKEXPT2> diskinfo
Test Disk (0 - 1 ) ? 0
Peripheral Qualifier: Requested LUN is supported
Peripheral Device Type: Direct-access device
Medium is NOT removable
Device-type Modifier = 0(0x0)
ISO Version = 0 | ECMA Version = 0 | ANSI Version = 3
Reserved
Device does NOT support the TERMINATE I/O PROCESS message
INQUIRY data format is as specified in SCSI-2
Other supported features:
16-bit wide data transfer, Synchronous data transfer, Linked commands, Tagged Command Queuing
This device responds to a RESET condition with a SOFT RESET alternative
Vendor Identification: HP 36.4G
Product Identification: ST336753LC
Product Revision Level: HPC3
Vendor Specific Information:
Addr | Hexadecimal | ASCII
---------------------------------------------------------------------
36 (0x24 ) | 0x33 0x48 0x58 0x30 0x4b 0x38 0x52 0x57 | 3HX0K8RW
44 (0x2c ) | 0x20 0x20 0x20 0x20 0x53 0x45 0x41 0x47 | SEAG
52 (0x34 ) | 0x41 0x54 0x45 0x20 | ATE
Any additional information from the vendor:
Addr | Hexadecimal | ASCII
---------------------------------------------------------------------
96 (0x60 ) | 0x00 0x43 0x6f 0x70 0x79 0x72 0x69 0x67 | .Copyrig
104 (0x68 ) | 0x68 0x74 0x20 0x28 0x63 0x29 0x20 0x32 | ht (c) 2
112 (0x70 ) | 0x30 0x30 0x32 0x20 0x53 0x65 0x61 0x67 | 002 Seag
120 (0x78 ) | 0x61 0x74 0x65 0x20 0x41 0x6c 0x6c 0x20 | ate All
128 (0x80 ) | 0x72 0x69 0x67 0x68 0x74 0x73 0x20 0x72 | rights r
136 (0x88 ) | 0x65 0x73 0x65 0x72 0x76 0x65 0x64 0x20 | eserved
DISKEXPT2> modesense
Test Disk (0 - 1 ) ? 1
---------------------------------------------
POSSIBLE PAGE CODES
---------------------------------------------
0x01 - Read-write error recovery page
0x02 - Disconnect-reconnect page
0x03 - Format device page
0x04 - Rigid disk geometry page
0x05 - Flexible disk page
0x07 - Verify error recovery page
0x08 - Caching Page
0x09 - Peripheral device page
0x0A - Control mode page
0x0B - Medium types supported page
0x0C - Notch and partition page
0x3F - Return all pages
34 Performing Common ODE Tasks
--------------------------------------------Page Code<Return to quit>? 0x09
Addr | Hexadecimal | ASCII
---------------------------------------------------------------------
0 (0x0 ) | 0x00 0x1e 0x00 0x10 0x00 0x00 0x00 0x08 | ........
8 (0x8 ) | 0x00 0x00 0x00 0x00 0x00 0x00 0x02 0x00 | ........
16 (0x10 ) | 0x89 0x0e 0x00 0x00 0x00 0x00 0x00 0x00 | ........
24 (0x18 ) | 0x00 0x00 0x00 0x00 0x00 0x00 0x04 0x00 | ........
DISKEXPT2> help modesense
----------------------------------------------------------------------- MODESENSE COMMAND
-----------------------------------------------------------------------This command reads the mode sense page from SCSI device and displays the
contents in HEX and ASCII.
This command takes two optional parameters; disk index and page code. When
no parameters are given as part of the command, and the environment variable
TESTDISK is not set, it prompts the user to supply the disk index and the
page code. A list of possible page codes are given to the user.
SYNTAX: MODESENSE [<disk index> <page code> ]
EXAMPLE:
DISKEXPT > MODESENSE 1 0x3f
NOTES:
1.All parameters can be in decimal or hex(0x/0Xnnn or nnnH/h formats).
Default is decimal.
2.There are no standard set of supported page codes across all devices.
The device responds with proper error messages if non-supported page
codes are choosen.
------------------------------------------------------------------------
DISKEXPT2> ex
Running ODE Tools on HP 9000 Systems 35
36
Index
Symbols
.cdimage file, 14
64-bit systems
convention for naming tools, 14
A
ASTRODIAG2
described, 13
B
BCH, 15
Boot Console Handler (see BCH)
Boot Manager menu on Integrity Systems and Itanium
worksations, 11
C
CD
download image for HP 9000 systems, 14
download image for Integrity Systems and Itanium
worksations, 10
ordering for HP 9000 systems, 14
ordering for Integrity Systems and Itanium
worksations, 9
CD_Installer, 12
cdimage file, 10
CIODIAG
described, 13
CIODIAG2
described, 9
command-line interface, 7
COPYUTIL2
described, 13
CPUDIAG , 9
(see also cpudiag command)
(see also memdiag command)
described, 9
cpudiag command, 19
(see also CIODIAG)
error-detection example, 24
example of loading and running, 19
example of using with memdiag, 22
D
DFDUTIL
described, 9
DFDUTIL2
described, 13
diskexpt command
running, 32
DISKEXPT2
described, 13
DISKUTIL2
described, 13
E
EFI prompt, 11
error message
when entering invalid command, 25
when using the wrong tools, 24
ESCDIAG
described, 13
F
FCFUPDATE
described, 9
H
HP 9000 CD (see HP 9000 systems)
HP 9000 systems
download image for CD, 14
obtaining tools for, 14
ordering cd for, 14
Running ODE from CD, 15
tools provided for, 13
HP-UX 11.20, 8
HPSP (see HPSP)
installing files onto, 11
overview of, 10
procedure for running ODE from , 10
I
I/O card utilities, 12
IKEDIAG2
described, 13
Integrity Systems and Itanium worksations
download image for CD, 10
obtaining tools for, 9
ordering CD for, 9
Running ODE from CD, 11
interfaces (see user interfaces)
invalid command (see error message)
IODIAG
described, 9
IOTEST2
described, 13
iso
cdimage file, 10
Itanium workstations, 9
L
launchmenu, 11
ls command
using to determine available tools, 25
M
MAKODIAG
described, 13
makodiag command
running, 29
37
MAPPER
described, 9
MAPPER2
described, 13
mapper2 command
examining and running, 26
MCA utilities, 12
MEM2
described, 13
MEMDIAG
described, 9
memdiag command
example of using with cpudiag, 22
menu-driven interface, 7
MOABDIAG
described, 13
modules
list of, 7
N
N-CLass, 14
network utilities, 12
T
test controller
described, 7
test modules
described, 7
TOGODIAG
described, 13
tools, 9
(see also Integrity Systems and Itanium worksations)
(see also HP 9000 systems)
for Integrity Systems and Itanium worksations, 9
naming convention, 14
non-ODE, 11
U
user interfaces
menu unavailable, 15
overview of, 7
using the wrong tools, 24
V
V-class system, 8
O
ode command
running, 25
P
PACIODIAG
described, 13
PCIUTIL
described, 9, 13
PDC prompt, 15
PERFVER
described, 9
PERFVER2
described, 13
PLUTODIAG
described, 9, 13
Processor Dependent Code (see PDC prompt)
R
REODIAG
described, 13
restrictions on using ODE tools, 8
running ODE
steps for from HP 9000 systemsCD, 15
steps for from Integrity Systems and Itanium
worksations CD, 11
W
WDIAG
described, 13
Web
downloading imagefor Integrity Systems and Itanium
worksations from, 10
ordering CD using, 14
S
service partition (see HPSP)
Software Depot
obtaining software from, 9
Support Plus Media, 8
SysLib
See system library, 7
system library, 7
38 Index
Loading...