HP Compaq 8100 Elite PC QuickSpecs
Hardware Reference Guide
HP Compaq 8100 Elite Small Form Factor Business
PC and HP Z200 Small Form Factor Workstation
© Copyright 2010 Hewlett-Packard
Development Company, L.P.
Microsoft, Windows, and Windows Vista are
either trademarks or registered trademarks
of Microsoft Corporation in the United States
and/or other countries.
The only warranties for HP products and
services are set forth in the express warranty
statements accompanying such products
and services. Nothing herein should be
construed as constituting an additional
warranty. HP shall not be liable for technical
or editorial errors or omissions contained
herein.
This document contains proprietary
information that is protected by copyright. No
part of this document may be photocopied,
reproduced, or translated to another
language without the prior written consent of
Hewlett-Packard Company.
Hardware Reference Guide
HP Compaq 8100 Elite Small Form Factor
Business PC and HP Z200 Small Form
Factor Workstation
Second Edition (February 2010)
Document Part Number: 593073-002
About This Book
This guide provides basic information for upgrading this computer model.
WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily
harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in damage
to equipment or loss of information.
NOTE: Text set off in this manner provides important supplemental information.
ENWW iii
iv About This Book ENWW
Table of contents
Hardware Upgrades ............................................................................................................................................ 1
Warnings and Cautions ........................................................................................................................ 1
Additional Information ........................................................................................................................... 1
Unlocking the Smart Cover Lock .......................................................................................................... 1
Smart Cover FailSafe Key ................................................................................................... 2
Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock ............................. 2
Removing the Computer Access Panel ................................................................................................ 4
Replacing the Computer Access Panel ................................................................................................ 5
Removing the Front Bezel .................................................................................................................... 6
Removing Bezel Blanks ....................................................................................................................... 6
Replacing the Front Bezel .................................................................................................................... 8
Using the Small Form Factor Computer in a Tower Orientation .......................................................... 8
Installing Additional Memory .............................................................................................................. 11
DIMMs ............................................................................................................................... 11
DDR3-SDRAM DIMMs ...................................................................................................... 11
Installing DIMMs ................................................................................................................ 12
Removing or Installing an Expansion Card ........................................................................................ 15
Drive Positions ................................................................................................................................... 20
Installing and Removing Drives .......................................................................................................... 21
Removing an External 5.25-inch Drive .............................................................................. 23
Installing an Optical Drive into the 5.25-inch Drive Bay ..................................................... 25
Removing an External 3.5-inch Drive ................................................................................ 28
Installing a Drive into the 3.5-inch External Drive Bay ....................................................... 30
Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive ........................ 32
Removing and Replacing a Removable 3.5-inch SATA Hard Drive .................................. 36
Battery Replacement .......................................................................................................................... 40
Installing a Security Lock .................................................................................................................... 43
HP/Kensington MicroSaver Security Cable Lock ............................................................... 43
Padlock .............................................................................................................................. 43
HP Business PC Security Lock .......................................................................................... 44
Front Bezel Security .......................................................................................................... 47
Appendix A Electrostatic Discharge .............................................................................................................. 49
Preventing Electrostatic Damage ....................................................................................................... 49
Grounding Methods ............................................................................................................................ 49
Appendix B Computer Operating Guidelines, Routine Care and Shipping Preparation .......................... 50
Computer Operating Guidelines and Routine Care ............................................................................ 50
ENWW v
Optical Drive Precautions ................................................................................................................... 51
Operation ........................................................................................................................... 51
Cleaning ............................................................................................................................. 51
Safety ................................................................................................................................. 51
Shipping Preparation .......................................................................................................................... 51
Index ................................................................................................................................................................... 52
vi ENWW
Hardware Upgrades
Warnings and Cautions
Before performing upgrades be sure to carefully read all of the applicable instructions, cautions, and
warnings in this guide.
WARNING! To reduce the risk of personal injury from electrical shock, hot surfaces, or fire:
Disconnect the power cord from the wall outlet and allow the internal system components to cool before
touching.
Do not plug telecommunications or telephone connectors into the network interface controller (NIC)
receptacles.
Do not disable the power cord grounding plug. The grounding plug is an important safety feature.
Plug the power cord in a grounded (earthed) outlet that is easily accessible at all times.
To reduce the risk of serious injury, read the Safety & Comfort Guide. It describes proper workstation,
setup, posture, and health and work habits for computer users, and provides important electrical and
mechanical safety information. This guide is located on the Web at
WARNING! Energized and moving parts inside.
http://www.hp.com/ergo.
Disconnect power to the equipment before removing the enclosure.
Replace and secure the enclosure before re-energizing the equipment.
CAUTION: Static electricity can damage the electrical components of the computer or optional
equipment. Before beginning these procedures, ensure that you are discharged of static electricity by
briefly touching a grounded metal object. See
When the computer is plugged into an AC power source, voltage is always applied to the system board.
You must disconnect the power cord from the power source before opening the computer to prevent
damage to internal components.
Electrostatic Discharge on page 49 for more information.
Additional Information
For more information on removing and replacing hardware components, desktop management, the
Computer Setup utility, and troubleshooting, refer to the Maintenance and Service Guide (available in
English only) for your computer model at
http://www.hp.com.
Unlocking the Smart Cover Lock
NOTE: The Smart Cover Lock is an optional feature included on some models only.
The Smart Cover Lock is a software-controllable cover lock, controlled by the setup password. This lock
prevents unauthorized access to the internal components. The computer ships with the Smart Cover
Lock in the unlocked position. For more information about locking the Smart Cover Lock, refer to the
Maintenance and Service Guide (available in English only).
ENWW Warnings and Cautions 1
Smart Cover FailSafe Key
If you enable the Smart Cover Lock and cannot enter your password to disable the lock, you will need
a Smart Cover FailSafe Key to open the computer cover. You will need the key to access the internal
computer components in any of the following circumstances:
Power outage
●
Startup failure
●
PC component (for example, processor or power supply) failure
●
Forgotten password
●
NOTE: The Smart Cover FailSafe Key is a specialized tool available from HP. Be prepared; order this
key before you need it.
To obtain a FailSafe Key:
Contact an authorized HP reseller or service provider. Order PN 166527-001 for the wrench-style
●
key or PN 166527-002 for the screwdriver bit key.
Refer to the HP Web site (
●
Call the appropriate number listed in the warranty or in the Support Telephone Numbers guide.
●
http://www.hp.com) for ordering information.
Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock
To open the access panel with the Smart Cover Lock engaged:
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, then turn off any external devices.
4. Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. You must disconnect the power cord to
avoid damage to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
2 Hardware Upgrades ENWW
6. Use the Smart Cover FailSafe Key to remove the tamper-proof screw that secures the Smart Cover
Lock to the chassis.
NOTE: Your computer may look different than the illustration shown below.
Figure 1 Removing the Smart Cover Lock Screw
You can now remove the access panel. See Removing the Computer Access Panel on page 4.
To reattach the Smart Cover Lock, secure the lock in place with the tamper-proof screw.
ENWW Unlocking the Smart Cover Lock 3
Removing the Computer Access Panel
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, then turn off any external devices.
4. Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. You must disconnect the power cord to
avoid damage to the internal components of the computer.
5. If the computer is on a stand, remove the computer from the stand.
6. Lift up on the access panel handle (1) then lift the access panel off the computer (2).
NOTE: Your computer may look different than the illustration shown below.
Figure 2 Removing the Access Panel
4 Hardware Upgrades ENWW
Replacing the Computer Access Panel
Slide the lip on the front end of the access panel under the lip on the front of the chassis (1) then press
the back end of the access panel onto the unit so that it locks into place (2).
NOTE: Your computer may look different than the illustration shown below.
Figure 3 Replacing the Access Panel
ENWW Replacing the Computer Access Panel 5
Removing the Front Bezel
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, then turn off any external devices.
4. Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. You must disconnect the power cord to
avoid damage to the internal components of the computer.
5. Remove the access panel.
6. Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2).
NOTE: Your computer may look different than the illustration shown below.
Figure 4 Removing the Front Bezel
Removing Bezel Blanks
On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that
need to be removed before installing a drive. To remove a bezel blank:
1. Remove the access panel and front bezel.
6 Hardware Upgrades ENWW
2. To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards
the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it (2).
NOTE: Your computer may look different than the illustration shown below.
Figure 5 Removing a Bezel Blank
ENWW Removing Bezel Blanks 7
Replacing the Front Bezel
Insert the three hooks on the bottom side of the bezel into the rectangular holes on the chassis (1) then
rotate the top side of the bezel onto the chassis (2) and snap it into place.
NOTE: Your computer may look different than the illustration shown below.
Figure 6 Replacing the Front Bezel
Using the Small Form Factor Computer in a Tower Orientation
The Small Form Factor computer can be used in a tower orientation with an optional tower stand that
can be purchased from HP.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, then turn off any external devices.
4. Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. You must disconnect the power cord to
avoid damage to the internal components of the computer.
8 Hardware Upgrades ENWW
5. Orient the computer so that its right side is facing down and place the computer in the optional
stand.
NOTE: Your computer may look different than the illustration shown below.
Figure 7 Changing from Desktop to Tower Orientation
NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the optional
tower stand.
6. On the back of the Z200 Small Form Factor (SFF) Workstation front bezel, squeeze the HP logo
mounting tabs (1) and press the logo outward (2) as shown in the following illustration.
NOTE: Your computer may look different than the illustration shown below.
Figure 8 Rotating the Z200 SFF Logo
Rotate the HP logo 90 degrees counterclockwise, and then release the logo and press it back into
place in the front bezel.
7. Reconnect the power cord and any external devices, then turn on the computer.
ENWW Using the Small Form Factor Computer in a Tower Orientation 9
NOTE: Ensure at least 10.2 centimeters (4 inches) of space on all sides of the computer remains
clear and free of obstructions.
10 Hardware Upgrades ENWW
Installing Additional Memory
The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs).
DIMMs
The memory sockets on the system board can be populated with up to four industry-standard DIMMs.
These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum
memory support, you can populate the system board with up to 16-GB of memory.
DDR3-SDRAM DIMMs
For proper system operation, the DDR3-SDRAM DIMMs must be:
industry-standard 240-pin
●
unbuffered non-ECC PC3-8500 DDR3-1066 MHz-compliant or PC3-10600 DDR3-1333 MHz-
●
compliant
unbuffered ECC PC3-10600 DDR3-1333 MHz-compliant (Z200 SFF only)
●
1.5 volt DDR3-SDRAM DIMMs
●
The DDR3-SDRAM DIMMs must also:
support CAS latency 7 DDR3 1066 MHz (7-7-7 timing) and CAS latency 9 DDR3 1333 MHz (9-9-9
●
timing)
contain the mandatory JEDEC SPD information
●
In addition, the computer supports:
single-sided and double-sided DIMMs
●
DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM are not
●
supported
NOTE: The 8100 SFF supports 512Mbit, 1Gbit, and 2Gbit non-ECC memory technologies. The
Z200 SFF supports 512Mbit, 1Gbit, and 2Gbit ECC and non-ECC memory technologies.
NOTE: The system will not operate properly if you install unsupported DIMMs.
ENWW Installing Additional Memory 11
Installing DIMMs
CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power to
drain before adding or removing memory modules. Regardless of the power-on state, voltage is always
supplied to the memory modules as long as the computer is plugged into an active AC outlet. Adding
or removing memory modules while voltage is present may cause irreparable damage to the memory
modules or system board.
The memory module sockets have gold-plated metal contacts. When upgrading the memory, it is
important to use memory modules with gold-plated metal contacts to prevent corrosion and/or oxidation
resulting from having incompatible metals in contact with each other.
Static electricity can damage the electronic components of the computer or optional cards. Before
beginning these procedures, ensure that you are discharged of static electricity by briefly touching a
grounded metal object. For more information, refer to
When handling a memory module, be careful not to touch any of the contacts. Doing so may damage
the module.
NOTE: Do not intermix non-ECC memory DIMMs with ECC memory DIMMs.
1. Remove/disengage any security devices that prohibit opening the computer.
2. Remove all removable media, such as compact discs or USB flash drives, from the computer.
3. Turn off the computer properly through the operating system, then turn off any external devices.
Electrostatic Discharge on page 49.
4. Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the
power to drain before adding or removing memory modules. Regardless of the power-on state,
voltage is always supplied to the memory modules as long as the computer is plugged into an
active AC outlet. Adding or removing memory modules while voltage is present may cause
irreparable damage to the memory modules or system board.
5. If the computer is on a stand, remove the computer from the stand.
6. Remove the access panel.
WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system
components to cool before touching.
12 Hardware Upgrades ENWW
Loading...