HP 5406 zl, 5412 zl Installation And Getting Started Manual

HP 5400 zl Switches

Installation and Getting Started Guide

Power over Ethernet

HP 5400 zl Switches

Installation and Getting Started Guide

Hewlett-Packard Company
8000 Foothills Boulevard, m/s 5551
Roseville, California 95747-5551

http://www.hp.com/networking

© Copyright 2005 - 2013 Hewlett-Packard Development
Company, L.P.

Manual Part Number

5998-2998
June 2013

Applicable Products

HP 5406 zl Switch J8697A

HP 5406 zl-48G Switch J8699A

HP 5406 zl-48G-PoE+ Switch J9447A

HP 5412 zl Switch J8698A

HP 5412 zl-96G Switch J8700A

HP 5412 zl-96G-PoE+ Switch J9448A

HP 5412-92G-PoE+/2XG-SFP+ v2 zl Switch with Premium Software J9532A

HP 5406-44G-PoE+/2XG-SFP+ v2 zl Switch with Premium Software J9533A

HP 5406-44G-PoE+/4G-SFP v2 zl Switch with Premium Software J9539A

HP 5406 zl Switch with Premium Software J9642A

HP 5412-92G-PoE+/4G-SFP v2 zl Switch with Premium Software J9540A

HP 5412 zl Switch with Premium Software J9643A

Two-Post Rack Mounting Kit for 5406 zl 5069-8561

Two-Post Rack Mounting Kit for 5412 zl 5069-8562

8200 zl/5400 zl 10K Rack RailKit Assembly 5070-0145

Switch zl Power Supply Shelf J8714A

Switch zl Power Supply Shelf Rack Mounting Kit 5070-3028

Switch 1500W PoE+ zl Power Supply J9306A

Switch zl 875W Power Supply J8712A

Switch zl 1500W Power Supply J8713A

Switch 5406 zl Fan Tray J8697-60005

Switch 5412 zl Fan Tray J8698-60005

5400 zl Management Module without CF card J8726-61001

CompactFlash Kit for 5400 zl Management Module 5070-1056

HP 24-port Gig-T zl Module J8702A

HP 20-port Gig-T/SFP zl Module J8705A

HP 24-port mini-GBIC zl Module J8706A

HP 4-port 10Gig-X2 zl Module J8707A

HP 4-port 10Gig-CX4 zl Module J8708A

HP 24-Port 10/100/1000 PoE+ zl Module J9307A

HP 20-Port 10/100/1000 PoE+/4-Port MiniGBIC zl Module J9308A

HP 4-Port 10GbE SFP+ zl Module J9309A

HP 24-Port 10/100 PoE+ zl Module J9478A

Wireless Edge Services zl Module J9051A

Redundant Wireless Services zl Module J9052A

ONE Services zl Module J9154A

ONE Advanced Services zl Module J9545A

HP 24-port Gig-T PoE+ v2 zl Module J9534A

HP 20-port Gig-T PoE+ / 4-port SFP v2 zl Module J9535A

HP 20-port Gig-T PoE+ / 2-port 10-GbE SFP+ v2 zl Module J9536A

HP 24-port SFP v2 zl Module J9537A

HP 8-port 10-GbE SFP+ v2 zl Module J9538A

HP 8-port 10GBase-T v2 zl Module J9546A

HP 24-port 10/100 PoE+ v2 zl Module J9547A

HP 20-port Gig-T / 2-port 10-GbE SFP+ v2 zl Module J9548A

HP 20-port Gig-T / 4-port SFP v2 zl Module J9549A

HP 24-port Gig-T v2 zl Module J9550A

HP 12-port Gig-T / 12-port SFP v2 zl Module J9637A

Disclaimer

HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF
ANY KIND WITH REGARD TO THIS MATERIAL, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. Hewlett-Packard shall not be liable for errors
contained herein or for incidental or consequential damages in
connection with the furnishing, performance, or use of this
material.

The information contained herein is subject to change
without notice.The only warranties for HP products and services
are set forth in the express warranty statements accompanying
such products and services. Nothing herein should be construed
as constituting an additional warranty. HP shall not be liable for
technical or editorial errors or omissions contained herein.

Hewlett-Packard assumes no responsibility for the use or
reliability of its software on equipment that is not furnished by
Hewlett-Packard.

Warranty

For HP warranty information, visit

www.hp.com/networking/support

A copy of the specific warranty terms applicable to your Hewlett­Packard products and replacement parts can be obtained from
your HP Sales and Service Office or authorized dealer.

Safety

Before installing and operating these products, please read the

“Installation Precautions” in Chapter 2, andthe safety statements

in Appendix C.

iii

Contents

1 Introducing the HP 5400 zl Switches

Overview of HP 5400 zl Switches .................................. 1-2

HP 5406 zl Switches .........................................1-2

HP 5412 zl Switches .........................................1-3

HP 5406 zl Switch ...........................................1-4

HP 5412 zl Switch ...........................................1-5

Network Connectivity, Speeds and Technologies ....................1-6

Front of the Switch .............................................. 1-7

LEDs ...................................................... 1-8

LED Mode Select Button and Indicator LEDs ...................1-11

Console Port ..............................................1-13

Reset Button ..............................................1-13

Clear Button ...............................................1-13

Back of the Switch .............................................1-14

Power Connector ..........................................1-14

Redundant Power Supply ....................................1-15

Switch Accessories .............................................1-16

Switch Features ...............................................1-17

2 Installing the HP 5400 zl Switches

Included Parts .................................................. 2-1

Accessory Kits .............................................2-2

Power Cords ...............................................2-2

Installation Procedures ..........................................2-3

Summary ................................................... 2-3

Installation Precautions ...................................... 2-4

Installation Precautions (continued) ........................... 2-5

iv

1. Prepare the Installation Site ................................2-6

Cabling Infrastructure ....................................2-6

Installation Location .....................................2-6

2. Install Switch Modules .....................................2-6

Installing a Management Module Battery ....................2-8

3. (Optional) Install Another Power Supply .....................2-10

4. Verify the Switch Passes Self Test ..........................2-12

LED Behavior: .........................................2-14

5. Mount the Switch ........................................2-14

Rack or Cabinet Mounting ............................... 2-14

Horizontal Surface Mounting .............................2-17

6. Install the Grounding Wire .................................2-17

7. Connect the Switch to a Power Source ......................2-18

8. (Optional) Connect a Power Supply Shelf

to the switch .............................................2-18

EPS Operation .........................................2-19

Operating Characteristics of the EPS (J8714A) ..............2-19

Power Supply Shelf LEDs ................................2-20

Connecting the Power Supply Shelf .......................2-20

9. Connect the Network Devices ..............................2-21

10. (Optional) Connect a Console to the Switch ................. 2-22

Terminal Configuration .................................. 2-23

Direct Console Access ...................................2-24

Console Cable Pinouts ..................................2-24

Telnet Console Access ..................................2-25

Hot Swapping Switch Modules ...................................2-26

Adding or Replacing Modules ................................2-26

Changing the Module Type .................................. 2-26

Example Network Topologies ...................................2-27

Basic Connectivity .........................................2-27

Use as an Edge Switch ......................................2-28

Optimizing the 10-GbE Port Configuration .....................2-29

Optimizing the 10-GbE Port Configuration with version 2 zl modules . .
2-30

3 Getting Started With Switch Configuration

Recommended Minimal Configuration ..........................3-1

Using the Switch Setup Screen ................................3-2

v

Where to Go From Here ...................................... 3-4

Using the IP Address for Remote Switch Management ................3-5

Starting a Telnet Session .....................................3-5

Starting a Web Browser Session ...............................3-5

Configuring the HP Wireless Edge Services zl Modules (J9051A, J9052A) 3-7

Configuring an IP Address for the Module ....................... 3-7

Configuring VLANs on the zl Switch ............................3-9

Determining a Module Configuration Backup Process ............3-9

Configuring Wireless LAN Services ...........................3-10

4 Replacing Components

Replacing Power Supplies ........................................4-2

Replacing Fan Trays ............................................. 4-4

Replacing the Management Module ................................4-5

Replacing the Management Module Compact Flash Card .............4-6

Installing a Compact Flash Card ............................... 4-6

Replacing the J9289A ONE Services zl Module Compact Flash Card ....4-7

Installing a Compact Flash Card ............................... 4-7

Replacing the J9289A ONE Services zl Module Disk Drive ............ 4-8

Installing (or Replacing) a Disk Drive .......................... 4-8

5 Troubleshooting

Basic Troubleshooting Tips ......................................5-2

Diagnosing with the LEDs ........................................5-4

HP networking tools ............................................5-9

Hardware Diagnostic Tests ......................................5-10

Reasons for Resetting the Switch .............................5-10

Methods of Resetting the Switch ..............................5-10

Testing the Switch by Resetting It ............................ 5-11

Checking the Switch LEDs ...............................5-11

Checking Console Messages ..............................5-11

Testing Twisted-Pair Cabling .................................5-12

Testing Switch-to-Device Network Communications ............ 5-12

vi

Testing End-to-End Network Communications .................5-12

Restoring the Factory Default Configuration ....................... 5-13

Downloading New Software .....................................5-14

HP Customer Support Services ..................................5-14

Before Calling Support ...................................... 5-14

A Specifications

Physical ................................................... A-1

Electrical ................................................. A-1

Environmental ............................................. A-2

Acoustic .................................................. A-2

5406 zl Switch and its bundles: ............................ A-2

5412 zl Switch and its bundles: ............................ A-2

Safety .................................................... A-3

Technology Standards and Safety Compliance .................. A-3

B Cabling and Technology Information

Cabling and Technology Information Specifications ............ B-1

Technology Distance Specifications ........................... B-3

Mode Conditioning Patch Cord .................................. B-5

Installing the Patch Cord .................................... B-5

Twisted-Pair Cable/Connector Pin-Outs ........................... B-7

Straight-Through Twisted-Pair Cable for

10 Mbps or 100 Mbps Network Connections .................... B-9

Cable Diagram ......................................... B-9

Pin Assignments ........................................ B-9

Crossover Twisted-Pair Cable for

10 Mbps or 100 Mbps Network Connection .................... B-10

Cable Diagram ........................................ B-10

Pin Assignments ....................................... B-10

Straight-Through Twisted-Pair Cable for

1000 Mbps Network Connections ............................ B-11

Cable Diagram ........................................ B-11

Pin Assignments ....................................... B-11

vii

C Safety and Regulatory Statements

Safety Information ............................................. C-1

Informations concernant la sécurité .............................. C-2

Hinweise zur Sicherheit ......................................... C-3

Considerazioni sulla sicurezza ................................... C-4

Consideraciones sobre seguridad ................................ C-5

Informações de Segurança ...................................... C-6

Safety Information (Japan) ...................................... C-7

Safety Information (China) ...................................... C-8

EMC Regulatory Statements ..................................... C-9

U.S.A. .................................................... C-9

Canada ................................................... C-9

Australia/New Zealand ...................................... C-9

Japan .................................................... C-10

Korea .................................................... C-10

Taiwan .................................................. C-10

Regulatory Model Identification Number ..................... C-10

European Community ...................................... C-11

D Recycle Statements

Waste Electrical and Electronic Equipment (WEEE) Statements ...... D-1

Index

1-1

Introducing the HP 5400 zl

Switches

1

Introducing the HP 5400 zl Switches

The HP 5400 zl switches include the 5406 zl switch, 5412 zl switch and their
bundles. They are multiport modular switches that provide Layer 3 routing
features, and also feature low latency for high-speed networking.

This chapter describes your 5400 zl switches, including:

■ Overview of 5400 zl switches, page 1-2

■ Network Connectivity, Speeds and Technologies, page 1-6

■ Front of the Switches, page 1-7

■ Back of the Switch, page 1-14

■ Switch Accessories, page 1-16

■ Switch Features, page 1-17

1-2

Introducing the HP 5400 zl Switches

Overview of HP 5400 zl Switches

Introducing the HP 5400 zl

Switches

Overview of HP 5400 zl Switches

HP 5406 zl Switches

1. The HP 5406 zl switch is available as an open 6-slot chassis (J9642A) with
Premium Features activated.

2. The HP 5406zl-48G switch bundle (J8699A) ships with the 5406 zl 6-slot
chassis without Premium Features and the following:

• Two 24-port 10/100/1000-T zl Modules (J8702A)

• One 875 W PoE Power Supply (J8712A) pre-installed.

3. The HP 5406zl-48G-PoE+ switch bundle (J9447A) ships with the 5406 zl
6-slot chassis without Premium Features and the following:

• One 24-port 10/100/1000-T PoE+ zl Modules (J9307A)

• One 20-port 10/100/1000-T PoE+ & 4-port mini-GBIC zl Module

(J9308A)

• One 1500W PoE+ zl Power Supply (J9306A)

4. The HP 5406-44G-PoE+/2XG-SFP+ v2 zl Switch with Premium Features
(J9533A) ships with the 5406 zl 6-slot chassis (J9642A) and the following:

• One 24-Port 10/100/1000 PoE+ v2 zl Module (J9534A)

• One 20-port 10/100/1000 PoE+ / 2-port SFP+ v2 zl module (J9536A)

• One 1500W PoE+ Power Supplies (J9306A)

• With Premium Features activated

5. The HP 5406-44G-PoE+/4G-SFP v2 zl Switch with Premium Features
(J9539A) ships with the 5406 zl 6-slot chassis (J9642A) and the following:

• One 24-port 10/100/1000 PoE+ v2 zl Module (J9534A)

• One 20-port 10/100/1000 PoE+ / 4-port SFP v2 zl module (J9535A)

• One 1500W PoE+ Power Supplies (J9306A)

• With Premium Features activated

1-3

Introducing the HP 5400 zl Switches

Overview of HP 5400 zl Switches

Introducing the HP 5400 zl

Switches

HP 5412 zl Switches

1. The HP 5412 zl switch is available as an open 12-slot chassis (J9643A) with
Premium Features activated.

2. The HP 5412zl-96G switch bundle (J8700A) ships with the 5412 zl 12 slot
chassis without Premium Features and the following:

• Four 24-port 10/100/1000-T zl Modules (J8702A)

• Two 875 W PoE Power Supply (J8712A) pre-installed.

3. The HP 5412zl-96G-PoE+ switch bundle (J9448A) ships with the 5412 zl
12 slot chassis without Premium Features and the following:

• Three 24-port 10/100/1000-T PoE+ zl Modules (J9307A)

• One 20-port 10/100/1000-T PoE+ & 4-port mini-GBIC zl Module

(J9308A)

• Two 1500W PoE+ zl Power Supplies (J9306A)

4. The HP 5412-92G-PoE+/2XG-SFP+ v2 zl Switch with Premium Features
(J9532A) ships with the 5412 zl 12-slot chassis and the following:

• Three 24-Port 10/100/1000 PoE+ v2 zl Module (J9534A)

• One 20-port 10/100/1000 PoE+ / 2-port SFP+ v2 zl module (J9536A)

• Two 1500W PoE+ Power Supplies (J9306A)

• With Premium Features activated

5. The HP 5412-92G-PoE+/4G-SFP v2 zl Switch with Premium Features
(J9540A) ships with the 5412 zl 12-slot chassis (J9643A) and the following:

• Three 24-Port 10/100/1000 PoE+ v2 zl Module (J9534A)

• One 20-port 10/100/1000 PoE+ / 4-port SFP v2 zl module (J9535A)

• Two 1500W PoE+ Power Supplies (J9306A)

• With Premium Features activated

See “Switch Accessories” on page 1-16 for a list of the switch modules that
can be installed in the HP 5400 zl switches.

1-4

Introducing the HP 5400 zl Switches

Overview of HP 5400 zl Switches

Introducing the HP 5400 zl

Switches

HP 5406 zl Switch

The HP 5406 zl switch ships with the 5400 zl Management Module and open,
6-slot chassis (J9642A). The switch needs at least one power supply to operate.
The 5406 zl switch bundles are not shown.

Figure 1-1. HP 5406 zl Switch (J9642A)

1-5

Introducing the HP 5400 zl Switches

Overview of HP 5400 zl Switches

Introducing the HP 5400 zl

Switches

HP 5412 zl Switch

The HP 5412 zl switch ships with the 5400 zl Management Module and open,
12-slot chassis (J9643A). It does not ship with any power supplies. The switch
needs at least one power supply to operate. The 5412 zl switch bundles are
not shown.

Figure 1-2. HP 5412 zl Switch (J9643A)

1-6

Introducing the HP 5400 zl Switches

Network Connectivity, Speeds and Technologies

Introducing the HP 5400 zl

Switches

Network Connectivity, Speeds and
Technologies

These products support optional network connectivity as follows:

Table 1-1. Optional Network Connectivity, Speeds and Technologies

Transceiver Form-Factor and Connector

1

Speed Technology

Cabling

SFP ("mini-GBIC")

Connector

X2

Connector

SFP+

Connector

100 Mbps

100-FX Fiber (multimode) LC

100-BX Fiber (single mode) LC

1 Gbps

1000-T Copper (twisted-pair) RJ-45

1000-SX Fiber (multimode) LC

1000-LX Fiber (multimode or single mode) LC

1000-LH Fiber (single mode) LC

1000-BX Fiber (single mode) LC

10 Gbps

10-Gig CX4 Copper (twinaxial) CX4

10-Gig
Direct Attach

Copper (twinaxial) Not

Applicable

10-Gig SR

Fiber (multimode) SC

LC

10-Gig LRM Fiber (multimode) SC

LC

10-Gig LR Fiber (single mode) SC LC

10-Gig ER

Fiber (single mode) SC LC

1

For supported transceivers, visit www.hp.com/networking/support.

– In the first textbox, type J4858 (for 100-Mb and Gigabit information), or J8436 (for 10-Gigabit information).
– Select any of the products that display in the dropdown list.
– Select Product support information. Then click on Manuals and find the T

ransceiver Support Matrix.

For technical details of cabling and technologies see "Cabling and Technology Information" in the appendices.

1-7

Introducing the HP 5400 zl Switches

Front of the Switch

Introducing the HP 5400 zl

Switches

Front of the Switch

LED Mode Select button

and indicator LEDs

Switch Modules and slots

with Link and Mode LEDs for each port located on each module

Power

and Fault

LEDs

Locator LED

Status LEDs for the

Fans, Power Supplies,

and Switch Modules

Reset and Clear

buttons

Auxiliary Port

Console

Port

Module Link
and Mode LEDs

Self Test LED

Figure 1-3. Front of 5406zl-48G Switch

This illustration shows the 5406zl-48G (J8699A), but the labeling and descrip­tions apply to all of the HP 5400 zl switches.

1-8

Introducing the HP 5400 zl Switches

Front of the Switch

Introducing the HP 5400 zl

Switches

LEDs

As described in the next two tables, there are LEDs on the switch chassis and
on the switch modules that keep you informed of the status of the switch and
the network connections.

Table 1-2. Switch Chassis LEDs

LEDs State Meaning

Power
(green)

On The switch is receiving power.

Off The switch is NOT receiving power.

Fault
(orange)

Off The normal state; indicates that there are no fault conditions on the switch.

Blinking1A fault has occurred on the switch, one of the switch modules, an individual port, a power

supply, or a fan. The Status LED for the module or other device with the fault will flash
simultaneously.

On On briefly at the beginning of switch self test after the switch is powered on or reset. If

on for a prolonged time, the switch has encountered a fatal hardware failure, or has
failed its self test. See chapter 4, “Troubleshooting” for more information.

Locator
(blue)

On
Blinking
Off

The Locator LED is used to locate a specific chassis in a area full of chassis. The LED
can be set to be on solid or blink for a specified number of minutes (1-1440). The default
is 30 minutes. Use the command “chassislocate”.

Test
(green/Orange)

Off The normal operational state; the switch is not undergoing self test.

On The switch self test and initialization are in progress after you have power cycled or

reset the switch. The switch is not operational until this LED goes off. The Self Test LED
also comes on briefly when you “hot swap” a module into the switch and the module is
automatically self tested.

Blinking1A component of the switch has failed its self test. The Status LED for that component,

for example a switch module, and the switch Fault LED will flash simultaneously.

DIMM
(green/Orange)

On DIMM status is known and fault free.

Off DIMM status is unknown.

Blinking1If DIMM, Fault, and Self Test LEDs are blinking, DIMM failed self-test.

If DIMM and Fault LEDs are blinking, an operational fault has occurred.
If fast blinking (400ms On and 400ms Off), an operational alert occurred and is

unresolved.

Chas
(green)/Orange

Reserved for future releases.

Flash
(green/Orange)

On Flash Card status is known and fault free

Off

Flash Card status is unknown.

1-9

Introducing the HP 5400 zl Switches

Front of the Switch

Introducing the HP 5400 zl

Switches

Blinking1If Flash, Fault, and Self Test LEDs are blinking, Compact Flash failed self-test.

If Flash and Fault LEDs are blinking, an operational fault has occurred.
If fast blinking (400ms On and 400ms Off), an operational alert occurred and is unresolved

(for example, the Compact Flash is not present).

Mgmt
(green/Orange)

On
Off
Blinking

1

A Management module is present and fault free.
The switch is powered off.
There is a fault on the Management module.

PoE
(green/Orange)

On
Off

If any PoE modules are installed.
If no PoE modules are installed.

Blinking

1

Blinking

2

Internal PoE fault.
External load fault or denied PoE power.

Temp
(green/Orange)

Off Switch temperature is normal.

Blinking1An over temperature condition has been detected.

Fan
(green/Orange)

On The cooling fans are operating normally.

Blinking1One or more of the cooling fans have failed. The switch Fault LED will be blinking

simultaneously.

Internal Power
(green/Orange ­numbers
corresponding to
the power supply
positions)

On A power supply is installed in the position in the back of the switch corresponding to the

number, and the supply is plugged in to an active AC power source. As shipped, the
switch has a single power supply in position 1.

Off A power supply is not installed in the position corresponding to the number.

Blinking1The power supply installed in the position corresponding to the number is not plugged

in to an active AC power source, or has experienced a fault. The switch Fault LED will
be blinking simultaneously.

EPS
(green/Orange)

On
Off

An External Power Supply is connected.
No External Power Supply is connected.

Blinking1The External Power Supply has a fault, or is connected but not plugged into AC power.

LEDs State Meaning

1-10

Introducing the HP 5400 zl Switches

Front of the Switch

Introducing the HP 5400 zl

Switches

Modules (green ­letters
corresponding to
the switch module
slots)

In PoE Mode:

On A module is installed in the switch module slot corresponding to the letter and the module

is undergoing or has passed self test. This also occurs when you install a module when
the switch is already powered on (“hot swap”).

Off A module is not installed in the switch module slot corresponding to the letter.

Blinking

1

On
Blinking

1

Blinking2
Off

The module status LED flashes very briefly when a module is being hot swapped. If the
LED flashes for a prolonged time, the module in the slot corresponding to the letter has
failed self test or encountered some other fault condition. See chapter 4,
“Troubleshooting” for a more information.

PoE is ok for this slot.
PoE internal fault for this slot.
PoE load fault or insufficient power for this slot.
The module in this slot is not a PoE module.

LED Mode Select
(5 green LEDs)

Act Indicates that the port Mode LEDs are displaying network activity information.

FDx Indicates that the port Mode LEDs are lit for ports that are in Full Duplex Mode.

PoE Indicates which ports are supplying PoE power.

• If the Mode LED is on the port is providing PoE power.

• If the Mode LED is off the port is not providing PoE power.

• If the Link LED is on the port is enabled for PoE.

• If the Link LED is off the port is disabled for PoE.

• If the Link LED is blinking, the port has an error or the port is denied power due to
insufficient power.

Spd Indicates the Port LEDs are displaying the connection speed at which each port is

operating:

• if the Port LED is off, the port is operating at 10 Mbps

• if the Port LED is blinking, the port is operating at 100 Mbps

• if the Port LED is on continuously, the port is operating at 1000 Mbps

Usr Reserved for future development

Auxiliary (green/
orange) For more
information see
the Management
and Configuration
Guide for your
switch.

Blinking
green

1

Indicates the switch is processing a USB command file.

On green The switch has successfully finished processing the USB command file.

Blinking
orange

2

Indicates an error condition.

Off Indicates that no USB device has been inserted, or that the inserted USB device cannot

be recognized, or that no command file can be found on the inserted USB device.

1

The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.

2

The blinking behavior is an on/off cycle once every 0.5 seconds, approximately.

LEDs State Meaning

1-11

Introducing the HP 5400 zl Switches

Front of the Switch

Introducing the HP 5400 zl

Switches

Table 1-3. Switch Module LEDs

These LEDs are located on the modules themselves, one pair for each port.

LED State Meaning

Link On Indicates the port is enabled and receiving a link beat signal (for the twisted-pair

ports), or a strong enough light level (for the fiber-optic ports) from the connected
device.

Off One of these conditions exists:

• no active network cable is connected to the port

• the port is not receiving link beat or sufficient light

• the port has been disabled through the switch console, the web browser
interface, ProCurve Manager

, or other network management tool.

Blinking

1

The port has failed self test. The switch Fault, Self Test LEDs, and appropriate
module status LEDs will flash simultaneously.

Mode Depending on the mode selected, displays the following: network activity information, whether

the port is configured for Full Duplex operation, maximum speed operation, or whether PoE
power is being supplied or not. See “LED Mode Select Button and Indicator LEDs” below for
more information.

1

The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.

LED Mode Select Button and Indicator LEDs

To optimize the amount of information that can be displayed for each of the
switch ports, the 5400 zl switches use a Mode LED for each port. The operation
of this LED is controlled by the LED Mode Select button on the switch chassis,
and the current selection is indicated by the mode indicator LEDs near the
button. Press the button to change from one mode to the next.

LED Mode Select button

and indicator LEDs

Mode LEDs

(one for each port)

1-12

Introducing the HP 5400 zl Switches

Front of the Switch

Introducing the HP 5400 zl

Switches

Figure 1-4. Mode LEDs and LED Mode Select Button

■ If the Activity

Act

indicator LED is lit, each port Mode LED displays
activity information for the port—it flickers as network traffic is received
and transmitted through the port.

■ If the Full Duplex

FDx

indicator LED is lit, the port Mode LEDs light for

those ports that are operating in full duplex.

■ If the speed

Spd

indicator LED is lit, the port LEDs behave as follows to

indicate the connection speed for the port:

• Off = 10 Mbps

• Blinking = 100 Mbps (the blinking behavior is a repeated on/off cycle

once every 0.5 sec.)

• On = 1000 Mbps

■ If the PoE

PoE

indicator LED is lit, the Link and Mode LEDs indicate PoE
status:
Link LED:

• On = PoE is enabled on this port

• Off = PoE is disabled on this port.

• Slow Blinking = Internal PoE fault on this port.

• Fast Blinking = This port is denied PoE power or has an external load

fault.

Mode LED:

• On = PoE power is be supplied on this port

• Off = PoE is not being supplied on this port.

1-13

Introducing the HP 5400 zl Switches

Front of the Switch

Introducing the HP 5400 zl

Switches

Console Port

This port is used to connect a console to the switch by using the serial cable
supplied with the switch. This connection is described under “Connecting a
Console to the Switch” in chapter 2, “Installing the 5400 zl Switches”. The
console is a full-featured interface that can be used to configure, monitor, and
troubleshoot the switch. It can be run on a PC, laptop, or handheld device
emulating a VT-100 terminal, or on a standard VT-100 terminal.

Reset Button

This button will reset the switch when powered on. This action clears any
temporary error conditions that may have occurred, executes the switch self
test, and resets all network activity counters to zero. The counters are
displayed in the switch console interface, the switch web browser interface,
and through SNMP network management applications, such as ProCurve
Manager.

Press the Reset button also after changing the module type that is installed in
any of the switch module slots while the switch is powered on. In this case,
the switch must be reset to initialize the new module type. See “Hot Swapping
Switch Modules” on page 2-26.

Clear Button

This button is used for the following purposes:

■ Deleting Passwords - When pressed by itself for at least one second, the

Clear button deletes any switch console access passwords that you may
have configured. Use this feature if you have misplaced the password and
need console access.

This button is provided for your convenience, but its presence means that
if you are concerned with the security of the switch configuration and
operation, you should make sure the switch is installed in a secure
location, such as a locked wiring closet.

■ Restoring Factory Default Configuration - When pressed with the

Reset button in a specific pattern, the Clear button clears any configura­tion changes you may have made through the switch console, the web
browser interface, or SNMP management, and restores the factory default
configuration to the switch. For the specific method to restore the factory
default configuration, see “Restoring the Factory Default Configuration”
in chapter 4, “Troubleshooting” of this manual.

1-14

Introducing the HP 5400 zl Switches

Back of the Switch

Introducing the HP 5400 zl

Switches

Back of the Switch

Grounding lug
mounting holes

AC power connector

Power and Fault LEDs

Slot for installing optional
redundant power supply

.

Figure 1-5. Back of a 5406 zl switch with one power supply

External PoE
power connectors

Figure 1-6. Back of a 5412 zl switch with two power supplies

Power Connector

The Series 5400 zl Switches do not have a power switch; they are powered on
when connected to an active AC power source. The 5400 zl switches automat­ically adjust to any voltage between 100-127 and 200-240 volts when using the
J8712A power supply, 200-240 volts when using the J8713A power supply, and
110-127 and 200-240 volts when using the J9306A power supply, and either 50
or 60 Hz. There are no voltage range settings required.

1-15

Introducing the HP 5400 zl Switches

Back of the Switch

Introducing the HP 5400 zl

Switches

Redundant Power Supply

Load-sharing redundant power supplies (HP Switch zl 875 W Power Supply,
J8712A, a Switch zl 1500 W Power Supply J8713A, or a Switch zl 1500 W PoE+
Power Supply J9306A) can be installed in the back of the 5400 zl switches. To
provide redundancy, each power supply should be connected to different AC
power sources. Then, if one AC power source fails, the switch will continue
to run.

Note The J8712A and J8713A power supplies can be paired within the same switch

or within the Power Supply Shelf. However,the J9306A power supply can only
be paired with another J9306A power supply within the same switch or within
the Power Supply Shelf. The J9306A power supply cannot be used with either
the J8712A or J8713A power supplies.

Caution The switch redundant power supply is hot swappable, but, as indicated by the

caution statement on the power supply, it must be disconnected from AC
power before being installed or removed.

CAUTION:

.
.

Disconnect AC power from the power supply BEFORE installing or
removing the supply. Otherwise, damage to the equipment may result.

.

Refer to the installation guide for proper power cord selection

Because the switch can run on a single supply, removing a redundant supply
will not interrupt switch operation. However,on the 5412 zl one power supply
will only supply enough power to run the module slots A-F. Slots G-L will not
receive any power unless there are at least two power supplies installed.

When power is restored from a second (or more) power supplies, a system
reload or interface module reset is required to restore operation to slots G-L.
To reset the interface modules, pull each module out about half way and then
reseat them. Do this for each module in slots G-L.

For more information regarding power see the:

■ HP Switch zl Internal Power Supply Installation Guide.

■ HP Power over Ethernet (PoE/PoE+) Devices Planning and Implemen-

tation Guide.

1-16

Introducing the HP 5400 zl Switches

Switch Accessories

Introducing the HP 5400 zl

Switches

Switch Accessories

Accessories of the 5400 zl switches include a 6 or 12-slot chassis for installing
any of the available zl Modules. The supported zl modules include:

■ 24-Port 10/100/1000 PoE+ zl Module (J9307A)

■ 20-Port 10/100/1000 PoE+/4-Port MiniGBIC zl Module (J9308A)

■ 4-Port 10GbE SFP+ zl Module (J9309A)

■ 24-Port 10/100 PoE+ zl Module (J9478A)

■ 24-port 10/100/1000-T zl PoE Module (J8702A) -- which can provide Power

over Ethernet (PoE) power to 802.3af compliant (and some pre-standard)
devices.

■ 20-port Gig-T and 4-port mini-GBIC/SFP zl PoE Module (J8705A)

■ 24-port mini-GBIC zl Module (J8706A)

■ 4-port 10Gig-X2 zl Module (J8707A)

■ 4-port 10Gig-CX4 zl Module (J8708A)

■ Wireless Edge Services zl Module (J9051A)

■ Redundant Wireless Services zl Module (J9052A)

■ ONE Services zl Module (J9289A)

■ 24-port Gig-T PoE+ v2 zl Module (J9534A)

■ 20-port Gig-T PoE+ / 4-port SFP v2 zl Module (J9535A)

■ 20-port Gig-T PoE+ / 2-port 10GbE SFP+ v2 zl Module (J9536A)

■ 24-port SFP v2 zl Module (J9537A)

■ 8-port 10GbE SFP+ v2 zl Module (J9538A)

■ 8-port 10GBase-T v2 zl Module (J9546A)

■ 24-Port 10/100 PoE+ v2 zl Module (9547A)

■ 20-port Gig-T / 2-port 10-GbE SFP+ v2 zl Module (J9548A)

■ 20-port Gig-T / 4-port SFP v2 zl Module (J9549A)

■ 24-port Gig-T v2 zl Module (J9550A)

■ 12-port Gig-T / 12-port SFP v2 zl Module (J9637A)

Note For detailed information about the zl modules, refer to the HP Switch zl

Modules Installation Guide.

For detailed information about PoE and PoE+ devices, refer to the HP PoE
(Power over Ethernet) Devices Planning and Implementation Guide.

To view or download this guide, visit www.hp.com/networking/support.

1-17

Introducing the HP 5400 zl Switches

Switch Features

Introducing the HP 5400 zl

Switches

Switch Features

The features of the 5400 zl switches include:

Note Some of the listed 5400 zl switch features require a Premium License.

■ modules can be installed in any order and in any combination and can the

“hot swapped”

■ supported transceivers can be hot swapped into the mini-GBIC zl Module

■ high performance—With standard zl modules, the 5406 zl Switch has a

routing/switching capacity of 322.8 Gbps, with a switch fabric speed of

345.6 Gbps and a throughput of 240.2 Mpps. With standard zl modules, the
5412 zl Switch has a routing/switching capacity of 645.6 Gbps, with a
switch fabric speed of 691.2 Gbps and a throughput of 480.3 Mpps

With v2 zl modules, the 5406 zl Switch has a routing/switching capacity of

496.8 Gbps, with a switch fabric speed of 561.6 Gbps and a throughput of
396 Mpps. With v2 zl modules, the 5412 zl Switch has a routing/switching
capacity of 993.6 Gbps, with a switch fabric speed of 1123.2 Gbps and a
throughput of 792 Mpps

■ plug-and-play networking—all ports are enabled—just connect the

network cables to active network devices and your switched network is
operational

■ automatic learning of the network addresses in the switch’s 16,000-

address forwarding table, with configurable address aging value

■ full-duplex operation available on all ports

■ easy management of the switch through several available interfaces:

• web browser interface—an easy to use built-in graphical interface

that can be accessed from common web browsers

• console interface—a full featured, easy to use, VT-100 terminal inter-

face for out-of-band switch management, or for TELNET access to
the switch. The console includes complete switch management
through a command line interface (CLI) and a slightly reduced feature
set accessible through an intuitive menu interface

• ProCurve Manager—an SNMP-based graphical interface that is used

to manage your entire network, included with your new switch

1-18

Introducing the HP 5400 zl Switches

Switch Features

Introducing the HP 5400 zl

Switches

• supported by ProCurve Manager—an HP OpenView application that

accurately displays your switch on network maps and provides a
graphical interface for configuring and monitoring your switch

■ support for the Spanning Tree Protocol to eliminate network loops

■ support for up to 2048 IEEE 802.1Q-compliant VLANs so you can divide

the attached end nodes into logical groupings that fit your business needs

■ Layer 3 routing functionality:

• IP static routes

• RIP V1 and V2

• IRDP - ICMP Router Discovery Protocol

• OSPF- Open Shortest Path First

• DHCP relay

■ support for many other advanced features to enhance network perfor-

mance, security,and control— for a description, seethe Management and
Configuration Guide which is on the HP networking Web site.

■ support for IEEE 802.3af standard, IEEE 802.3at standard, and

pre-standard PoE devices.

2-1

Installing the HP 5400 zl

Switches

2

Installing the HP 5400 zl Switches

The 5400 zl switches are easily installed. They come with an accessory kit that
includes the brackets for mounting the switch in a standard 19-inch telco rack,
or in an equipment cabinet. The switches have rubber feet already attached
so they can be securely located on a horizontal surface. This chapter shows
you how to install your 5400 zl switches.

Included Parts

The 5400 zl switches have the following components shipped with them:

■ HP 5400 zl Switch Welcome Mat

■ HP 5400 zl Switch Read Me First

■ HP 5400 zl Switches Safety and Regulatory Information

■ HP Switches General Safety and Regulatory Information

■ Console cable and RJ45-DB9 adapter (5189-6795))

■ Accessory Kit (page 2-2)

■ Power Cord (page 2-2)

2-2

Installing the HP 5400 zl Switches

Included Parts

Installing the HP 5400 zl

Switches

Accessory Kits

5406 zl Accessory Kit (5069-8561) 5412 zl Accessory Kit (5069-8562)

two mounting brackets two mounting brackets - these brackets

are twice as long as the brackets for the
5406 zl switches

eight 10 mm M4 screws to attach the
mounting

brackets to the switch

eight 10 mm M4 screws to attach the
mounting brackets to the switch

four 5/8-inch number 12-24 screws to
attach

the switch to a rack

four 5/8-inch number 12-24 screws to
attach the switch to a rack

Power Cords

Power cord, one of the following:

J8712A Power

Supply

J8713A Power

Supply

J9306A Power

Supply

Region Cable Cable Cable

Australia/New Zealand
China
Continental Europe
Denmark
Japan
Switzerland
United Kingdom/Hong Kong/Singapore
United States/Canada/Mexico
South Africa
Taiwan
Israel
Thailand
Argentina
Brazil
Chile

8121-0857
8121-1034
8120-5336
8120-5340
8120-5342
8120-5339
8120-5334
8121-0973
8120-5341
8121-0941
8121-1009
8121-0671
8120-8375
8121-1132
8120-8389

8121-0871
8121-0924
8120-6899
8120-6897
8120-6903
8120-6897
8120-6898
8120-6903
8121-0915
8120-6903
8121-1010
8121-0675
8121-0912
8121-1100
8121-0876

8121-0857
8121-1034
8120-5336
8120-5340
8121-0941

1

8120-5339
8120-5334
8121-0973

2

8120-5341
8121-0967
8121-1009
8121-0671
8120-8375
8121-1132
8120-8389

1

Japan: NEMA L6-20P, 200V.

2

A NEMA L6-20, 240V power cord is also available. Order part number 8121-0941. To

order go to www.hp.com/buy/parts.

Japan Power
Cord Warning