Honeywell Lyric T6 Installation Instructions

1

Turn OFF the power and remove the old thermostat

T6 SMART THERMOSTAT

Compatible with 24-230V on/off and OpenTherm®

Need help? For assistance please visit: getconnected.honeywell.com

Honeywell Control Systems Ltd., Skimped Hill Lane, Bracknell, Berkshire, RG12 1EB

Approvals

Conforms to protection requirements of the following directives: EMC: 2014/30/EU, LVD: 2014/35/EU and RED: 2014/53/EU. Hereby, Honeywell, declares that this thermostat is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following Internet address: http://hwll.co/DoC

Wi-Fi (2.4GHz): Max Power 100mW, 2.4–2.458GHz ErP: Class V (+3%), (EU) 811/2013

Must be installed by a competent person!

Read these instructions carefully. Failure to follow these instructions can damage the product or cause a hazardous condition.

appliances such as gas boilers, combi-boilers and heat pump. Also works with zone valve applications but not with electric heating (240V).

To ensure your safety, always make sure mains power is switched OFF before accessing wiring.

Before removing the old thermostat take a picture of the old thermostat’s wiring as reference then proceed to installation.

1.2-1.5 m

The T6 thermostat should not be placed near draughts, in direct sunlight or near heat sources. It should be at least 1.2 - 1.5 meters from the ﬂoor.

Maximum cable length between Receiver box and thermostat:

15m for 0.5mm² cable or 20m for 1.0mm² cable.

WEEE Directive 2012/19/EC Waste Electrical and Electronic Equipment directive

At the end of the product life dispose of the packaging and product in a corresponding recycling centre. Do not dispose of the unit with the usual domestic refuse. Do not burn the product.

Prepare Receiver Box

2

Before installation of the Receiver Box

Find a suitable location near to the boiler.

Needed during installation:

Cable with 2 wires from the Receiver Box (R4H810A) to thermostat.

Cable with 2 wires from the boiler to Receiver Box.

The Receiver Box requires 230V power

for installation

Loosen the front

screw to remove cover or tighten it when the cover is back in place.

Install the

3

A) Wall box or Rear Wiring

Receiver Box

Hinge open the terminal block ﬂap to access the cables and wall box screw holes.

Max 6 mm

min 0.25mm2 max 1.5mm

Please refer to the wiring diagrams over the page

B) Surface wiring

Use the cable clamps to secure the surface wiring.

C) Replace the cover

Locate the hinges at the top of the cover and

2

wall plate, close the cover and secure with the screw.

Install the

4

Remember to use the same wires that you connected to the Receiver Box when connecting to the thermostat.

A) B)

T6 thermostat

Using a screwdriver open wallplate terminal cover to connect wires

Optional Coverplate installation

Connect 2 thermostat wires to the T and T terminals and close cover.

T

T

T

T

S S

Complete

5

Turn ON mains power to the Heating Appliance and Receiver Box.

After powering up both devices the green LED is on.

installation

Push the button to check if the boiler switches on. Button lights green.

After power up, SETUP is displayed on the thermostat’s screen.

Attach the thermostat to the

C)

wallplate when ﬁnished.

32308180-017 A

6

Set Up and conﬁguration

Once setup is completed, if you need to change more settings go to the advanced menu. To access the advanced menu press for 5 seconds.

AM

PM

*1234

AM

PM

*****230****

1 2 3 4 5 6

AM

PM

***SETUP****

1) Touch to begin setting up the thermostat.

SETUP

*CLOCK

3) Set the clock format, time and date.

SETUP

**LANGUAGE**

2) Select your language.

SETUP

CONFIGURE W

4) Touch to ﬁnalise setup.

( to setup using the App is currently unsupported)

In the advanced menu the following settings can be adjusted:

Menu Item Default Options

LANGUAGE

OPENTHERM

CYCLE RATE

MINIMUM ON TIME

HEAT RANGE

SCHEDULE OPTIONS

EXTERNAL SENSOR

OPTIMISE

CLOCK

LOW LOAD CONTROL

TEMPERATURE OFFSET

RESET

FAILSAFE

English

-

6

1 minute

Min = 5.0ºC Max = 35.0ºC

Daily

No sensor 0 = No sensor, 1 = Room sensor

Opt. start OFF Opt. stop OFF

Format: 24h Time: --:-Date: 01/09/16

ON 0 = OFF, 1 = ON

0.0ºC 1.5 ºC to 1.5ºC

-

OFF

0 = English, 1 = Français, 2 = Español 3 = Deutsch, 4 = Nederlands, 5 = Italiano

OpenTherm boiler data when available

3, 6, 9 or 12

1, 2, 3, 4 or 5 minutes

Min: 5ºC to 21ºC, Max: 21ºC to 35ºC

1 = Daily schedule, 2 = 5+2 days schedule

Opt. start: 0 = OFF, 1 = ON, 2 = Delayed start Opt. stop: 0 = OFF, 1 = ON

Clock format: 1 = 12h, 2 = 24h Setup time and date

Factory, schedule, WiFi and HomeKit reset

0 = OFF, 1 = ON

5 sec

Wiring Diagrams

A) Basic 230V boiler B) Combi boiler

Receiver Box

Thermostat

s s

Boiler

Receiver Box

Thermostat

s s

T1 T2

Boiler*

C) OpenTherm boiler D) Two-port zone valve or S-plan

Receiver Box

Thermostat

Receiver Box

s s

T1 T2

Boiler*

For other wiring diagrams visit:

www.honeywelluk.com/ professional-zone/resource-centre/ WiringDiagrams/

V4043

Thermostat

s s

* See boiler speciﬁcations for correct terminals

Manufactured for and on behalf of the Environmental and Energy Solutions Division of Honeywell Technologies Sàrl, ACS-ECC EMEA, Z.A. La Pièce 16, 1180 Rolle, Switzerland by its Authorised Representative Honeywell Inc.

Loading...