Honeywell Lumidor Enforcer Data sheet

Lumidor Enforcer

Simple portable test and calibration
of Impact multi gas monitors

Enforcer

Convenient to Use

• Portable design

• Lightweight and compact

• Disposable multi gas cylinder

• Wall mounting bracket with security
fixing included

Easy to Operate

• Simple mechanical construction

• Attach the Impact

• Instrument is automatically recognised

• Press a single button to proceed

• Wait a minute

• Impact is now tested and calibrated

• Minimal training required

Minimize Running Costs

• No need for third parties

• Reduce instrument downtime

• Simplify operations

Easy to Maintain

• Durable plastic housing

• Wipe clean surfaces

• Replaceable gaskets and seals

• Built-in indicator tells you when
gas needs replacing

Maintain Records

• Calibration history recorded by instrument

• Print history via optional PC software

• Ensure compliance with regulations

Regulations require regular testing of
gas monitoring equipment to ensure that
the instrument will work as and when
required. The Enforcer allows you to easily
comply with regulations when using an
Impact multigas monitor without the need
for costly test facilities or third parties.

‘Bump’ testing should be carried out before use of
any portable gas detector. This involves exposing
each gas sensor to a known concentration of
target gas and ensuring that it responds correctly.
If not, the unit must be re-calibrated or serviced to
replace those parts not working.

Personal gas monitors are normally calibrated
every 3 to 6 months. Typically this requires
specialist knowledge and equipment that is costly
or the work is sub-contracted to a third party.
During this time instruments are not available for
use and so could delay essential operations or
force additional monitors to be purchased.

The Enforcer calibrates Impact multigas monitors
fitted with oxygen, flammable, carbon monoxide
and hydrogen sulfide sensors in less than two
minutes. Volumes and flow rates are minimized to
allow approximately 200 calibrations per cylinder
of gas making calibration as low in cost as a
‘Bump’ test.

Impact instruments when used with The Enforcer
are always available for use. Calibration results are
recorded for printing at a later date via the optional
PC software thereby ensuring that instrument
histories are always available if required.

General Specification

Enforcer Specification

Use Test and calibration accessory for use with Impact multigas monitor when fitted with oxygen, flammable, carbon monoxide

and hydrogen sulfide sensors

Technique A controlled amount of gas is applied to the instrument. The response is compared against historical data obtained during

Construction Poly Carbonate

Dimensions 170mm x 145mm x 560mm *

Weight 1.34Kg (47oz)

Ordering information Enforcer with multi gas cylinder: 2302B0831 (EN50054), 2302B1336 (EN61778)

Multi gas Cylinder Specification

Contents 100ppm Carbon Monoxide

Accuracy +/-5%

Number of applications >200
per cylinder (calculated)

Type 2AL

Standards Europe - One fill valve in accordance with prEN12205

Dimensions (approx.) 80mm x 240mm (3.1” x 9.5”)

Weight 0.44Kg (16oz)

Pressure 34 bar (maximum)

Ordering information Multi gas calibration gas cylinder: 2302D0833 (EN50054), 2302D0761 (EN61779)

manufacture and if within tolerance automatic adjustment of readings is made

(7” x 5.7” x 22”) *

*Maximum length includes cylinder and sliding tray in open position

Enforcer excluding multi gas cylinder: 2302B0650

40ppm Hydrogen Sulfide

2.5% Methane (CH4)
15% Oxygen
Nitrogen balance

USA / R.O.W. - DOT 39 Standard

1

• Screw the multi gas cylinder into Enforcer

• Check the pressure gauge to ensure the cylinder
is not empty

2

• Open the Enforcer by pulling the sliding tray forward

• The tray ‘locks’ open when lowered in its tracks

3

• Turn on and insert the Impact to be calibrated. The
instrument may be zeroed in fresh air first if required

• Ensure that the instrument is locked into position
on the guides located on the sliding tray

4

• Close the sliding tray by lifting the handle

• When closed Impact will automatically recognise
the Enforcer and prompt the user to continue

5

• Press the button to calibrate the Impact

• Calibration can take between 45 and 90 seconds
subject to the age of the instrument

• Upon completion Impact will display the results
of the calibration

• Results may be downloaded via the PC software
and printed for report purposes if required

As World leaders in gas detection solutions, Honeywell Analytics’

Find out more

www.honeywellanalytics.com

Customer business centre

Europe and the rest of the world

Honeywell Analytics AG

Wilstrasse 11-U11

CH-8610 Uster

Switzerland

Tel: [phone]

Fax: [phone]

[e-mail]

Customer business center

A

mericas

Honeywell Analytics Distribution, Inc.

400 Sawgrass Corporate Pkwy

Suite 100

Sunrise, FL 33325

USA

Tel: [phone]

Toll free: [phone]

Fax: [phone]

[e-mail]

www.honeywell.com

Lumidor range is best placed to provide the most efficient, practical
and cost-effective equipment. Wherever personal protection
is required, you can rely on our equipment to provide practical
solutions and to help keep your business running safely.

The Lumidor range of portable gas detection

MicroMAX Pro MicroMAX + MicroMAX PID Minimax XT Minimax XP Minimax X4

MicroMAX range

With lifetime warranties*, the MicroMAX range offers the most robust microprocessor
controlled multi gas monitors available. Providing all the personal gas protection features
you require, MicroMAX monitors can handle the very toughest working conditions.

*

Lifetime warranty excludes sensors, batteries and pump.

Minimax range

The Minimax range provides personal single and multi gas protection and operational compliance
in industrial environments. They are ideal for people working in areas that are not easily accessible
and/or where fixed detection systems are not installed or not practical.

Impact and Impact Pro

Impact and Impact Pro are ideal for providing personal protection against gases in tough environments,
especially in confined spaces where entry and exit may be difficult. The Impact range provides easy
and economical means of personal gas detection to meet compliance requirements. The Safelink
Entrant/Attendant function ensures safe working practices are followed.

Enforcer Safelink

The Enforcer helps you to
easily (and cost-effectively)
comply with regulations
requiring the regular testing
of instruments. Because it
can calibrate Impact multi gas
monitors within less than two
minutes, the instruments are
always ready for use. It also
reduces cost by avoiding the
need for specialist knowledge
and equipment,
or sub-contracting to
expensive third parties,
which also adds delays.

Safelink adds an extra safety
dimension, enabling two-way
communication in difficult areas.
Easy to use, the system links two
Impact Pro multi gas monitors
together, allowing a co-worker
in a confined space to be
monitored remotely, as well
as providing a way of
exchanging messages.

Please Note:

While every effort has been made to ensure
accuracy in this publication, no responsibility
can be accepted for errors or omissions.
Data may change, as well as legislation, and you
are strongly advised to obtain copies of the most
recently issued regulations, standards, and guidelines.
This publication is not intended to form the
basis of a contract.
© 2005 Honeywell Analytics

H_Enforcer_DS0278_V1

12/2005

© 2005 Honeywell Analytics

11120