Honeywell HZ-7200-MP1, HZ-7204U User Manual

IMPORTANT SAFETY
INSTRUCTIONS

WARNING – READ AND SAVE THESE

OPERATING AND SAFETY INSTRUCTIONS
BEFORE USING THIS HEATER. IF YOU DO
NOT UNDERSTAND THESES INSTRUCTIONS OR
PRODUCT LABELS PLEASE CALL
OUR CUSTOMER REPRESENTIVIES AT
[phone] FOR ASSISTANCE BEFORE
USING THIS PRODUCT.

Warning – Failure to follow any of these safety
instructions could result in fire, injury or death.

YOUR RESPONSIBILITIES

Electrical appliances may expose people to
hazards that can cause severe injury as well as
death. The use of electrical products may create
hazards that include, but are not limited to,
injury, fire, electrical shock and electrical system
damage. These instructions are intended to
provide you with the information you need to
use the product and to avoid such hazards.

When using electrical appliances, basic
precautions should always be followed to
reduce risk of fire, electric shock, and injury to
persons including the following:

1. Warning – Read all instructions before using

this heater.

EnErgy Smart®
Cool touCh hEatErS

modEl hZ-7200 SEriES
modEl hZ-7300 SEriES
modEl hZ-8000 SEriES

2. Warning – This heater is hot when in use.
To avoid burns, do not let bare skin touch
hot surfaces. If, provided, use handles
when moving this heater. Keep combustible
materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at
least 3 feet (0.9 m) from the front of the
heater and keep them away from the sides
and rear.

3. Warning – Extreme caution is necessary
when any heater is used by or near children
or invalids, and whenever the heater is left
operating and unattended.

4. Warning – Always unplug heater when not
in use.

5. Warning – Do not operate any heater with
a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged
in any manner. Discard heater or return
heater to authorized service facility for
examination and/or repair.

6. Warning – For residential use only.

7. Warning – Do not use outdoors.

8. Warning – This heater is not intended for

use in bathrooms, laundry areas and similar
indoor locations. Never locate heater where
it may fall into a bathtub or other water
container.

9. Warning – Do not run cord under carpeting.
Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange cord
away from traffic area and where it will not
be tripped over.

The Honeywell Trademark is used by Kaz USA, Inc. under license from Honeywell International Inc.

Honeywell International Inc. makes no representation or warranties with respect to this product.

10. CAUTION – THIS APPLIANCE HAS A
POLARIZED PLUG (ONE BLADE IS WIDER
THAN THE OTHER). TO REDUCE THE RISK
OF SHOCK, THIS PLUG IS INTENDED TO
FIT ONLY ONE WAY IN A POLARIZED
OUTLET. IF THE PLUG DOES NOT FIT
SECURELY IN THE OUTLET, REVERSE
THE PLUG. IF IT STILL DOES NOT FIT,
CONTACT A QUALIFIED ELECTRICIAN. DO
NOT ATTEMPT TO DEFEAT THIS SAFETY
FEATURE.

11. Warning – This heater draws 12.5 amps
during operation. To prevent overloading a
circuit, do not plug the heater into a circuit
that already has other appliances working.

12. Warning – It is normal for the plug to feel
warm to the touch; however, a loose fit
between the AC outlet (receptacle) and plug
may cause overheating and distortion of
the plug. contact a qualified electrician to
replace loose or worn outlet.

13. Warning – To disconnect the heater, first
turn off the product, then grip the plug body
and pull it from the wall outlet. Never pull by
the cord.

14. Warning – Do not insert or allow foreign
objects to enter any ventilation or exhaust
opening as this may cause an electric shock
or fire, or damage the heater.

15. Warning – To prevent a possible fire, do not
block air intakes or exhaust in any manner.
Do not use on soft surfaces, like a bed, or
where openings may become blocked.

16. Warning – A heater has hot and arcing or
sparking parts inside. Do not use it in areas
where gasoline, paint or flammable liquids
are used or stored.

17. Warning – Use this heater only as
described in this manual. Any other use
not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons.

Place the heater on a rm, level, open surface free from
obstructions and at least 3 feet (0.9 m) away from any wall
or combustible material.

DO NOT use on an unstable surface such as bedding or
deep carpeting.

BE SURE THE HEATER IS NOT IN A POSITION WHERE IT MAY
BE TRIPPED OVER BY CHILDREN OR PETS.

18. Warning – Always plug heater directly into
a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap
(outlet/power strip).

19. Warning – Never tamper with this product
or attempt to fix it. Any tampering with, or
modification of this product can result in
serious injury, death, or fire. Risk of electric
shock. Do not open. No user serviceable
parts inside.

20. Warning – Do not remove product labels
that contain warnings or safety instruction.

21. Caution – The output of this heater may vary
and its temperature may become intense
enough to burn exposed skin. Use of this
heater is not recommended for persons with
reduced sensitivity to heat or an inability to
react to avoid burns.

22. Caution – Before cleaning, or storage, or
when not in use, turn the product’s controls
to the OFF position and unplug the heater
from the electrical outlet and allow to cool.

23. Caution – Place the heater on a firm, level,
open surface free from obstructions and
at least 3 feet (0.9 m) away from any
combustible materials. DO NOT use on an
unstable surface such as bedding or deep
carpeting. Be sure the heater is not in a
position where it may be tripped over by
small children or pets. The heater’s rubber
feet will hold it firmly in position.

24. Caution – If your home has aluminum
wiring have a licensed electrician check
your receptacle’s connections. When
using a 1500 watt heater, aluminum wire
connections can cause a safety issue.

25.

SAVE THESE

INSTRUCTIONS

MOVING THE HEATERSET-UP

Turn o the heater.
Allow it to cool for ten minutes.
Unplug heater and move. This heater is equipped with a

convenient carrying handle for your convenience.

OPERATION

EnergySmart® Cool Touch Heaters require no assembly. Never
leave an operating unit unattended.
Plug the heater into an electrical wall outlet.

Models HZ-7200 & HZ-8000 Series – EnergySmart®
Cool Touch Heater Operation

Turn the heater on by pressing the Power Button (

). The

Power Indicator Light will illuminate. Fig. 1
To save up to 35% in energy bills, turn the Power Knob to

your Desired Temperature. There are four (4) comfort settings

Fig. 1

Power
Button

w

P

o

e

r

Energy Smart
Power Knob

n

e

r

r

u

C

▲

|

F

º

5

6

w

o

L

e

T

t

F

º

0

7

Desired

Temperature

Oscillation

Button

m

p

e

r

a

t

u

r

e

▲

7

5

º

F

|

8

0

º

O

F

s

c

H

i

i

g

h

l

l

a

t

e

of 65°F (18°C), 70°F (21°C), 75°F (24°C) and 80°F (27°C).
The EnergySmart® thermostat will automatically select the
appropriate power level to best accommodate your Desired
Temperature. As the air temperature (Current Temperature)
in the room approaches the Desired Temperature, the heater
will automatically lower the power consumption and provide
consistent warmth without wasting energy.

Illuminated LED lights will indicate the Current Room Temperature.

HZ-7200

Power
Button

Energy Smart
Power Knob

t

n

e

r

r

u

C

Oscillation

m

e

T

p

e

r

a

t

u

Button

r

e

NOTE: The LOW setting is designed to operate only if the
temperature is below 55°F (12°C). If the room temperature is
above 55°F (12°C), the heater will remain OFF until the
temperature drops below this level. If you want the heater to
operate when the room temperature is above 55°F (12°C),

P

o

w

e

r

Desired

w

Temperature

o

L

H

i

g

h

move the Power Knob to a higher setting.
To override the EnergySmart® feature and produce maximum

heat, turn the Power Knob clockwise to HIGH. The will run the
heater at constant 1500 watts.

To turn on the oscillation feature, press the (

) button once. To turn it o, press the ( ) button once more. Please note, the

HZ-8000

oscillation function will stop when the Energy Smart™ mode has reached the desired temperature and the heater is no longer
blowing warm air. It will start back up when the heater starts blowing warm air again.

Press the Power Button (

) and unplug the heater when you are nished using it and the Power Indicator Light will go out.

Model HZ-7300 Series – Deluxe EnergySmart® Cool Touch Heater Operation

Turn heater on by pressing Power Button (
The heater will default to the Constant HI mode and the
Current Temp Indicator will display the current room
temperature. Fig 2.

The Energy Usage Indicator will display the power
consumption used by the heater.

• If HIGH, the heater is drawing 1500 watts to quickly warm
the room

• If LOW, the heater is drawing 900 watts to slowly warm the
room or maintain the temperature

• If STAND BY, the heater is drawing no power as the room has
reached the Desired Temperature. At this point, the heater
is most ecient and is drawing only a few watts of energy
while in STAND BY mode.

) button.

Fig. 2

Energy Usage
Indicator

Constant and
EnergySmart™
Thermostat
Modes

SET Temp
Button

Oscillation
Button

Power Button

HZ-7300

®

®

O

s

c

i

l

l

a

t

e

2 3

OPERATION (continued)

To set the heater, the digital control is equipped with two
(2) modes: (See Fig. 2)

Constant Heat Mode - Choose from two (2) heat settings:

1. Constant Low, press SET to LO; this setting uses 900 watts
of power

2. Constant High, press SET to HI; this setting uses 1500 watts
of power

NOTE: Because the Low setting does not require as much electricity
to operate, it is more energy ecient and may be a better option if
you are concerned about saving energy.

EnergySmart™ Mode - A smart thermostat that helps you
save energy. Press SET to choose four (4) comfort settings of
65°F (18°C), 70°F (21°C), 75°F (24°C), 80°F (27°C). This is

SAFETY FEATURES

This EnergySmart® Cool Touch Heater is equipped with several devices and features for added protection:

- This heater was crafted using a high quality safety plastic which allows for the “Cool Touch” exterior. If the heater grille is
touched briey, it will not cause a burn. For safe operation, do not continuously hold bare skin against the grille..

• Tip over protection – a tip-over switch that disables the heater if it is accidentally tipped over.

• A high temperature safety control prevents overheating.

• Thermal cut-o fuse that will permanently shut down the heater should it operate at a higher than normal temperature.

your desired room temperature. The EnergySmart® thermostat
will automatically select the appropriate power level to best
accommodate your Desired Temperature. As the air temperature
(Current Temp) in the room approaches the Desired Temperature,
the heater will automatically lower the power consumption to
provide consistent warmth without wasting energy.

The Current Temp Indicator will display the current room
temperature.

In the EnergySmart® mode, the Energy Usage Indicator will display
what power consumption the heater has automatically selected to
eciently meet your Desired Temperature.

To override the EnergySmart® function, turn the heater OFF (
press SET to choose a Constant Heat mode.

) or

CLEANING AND STORAGE

It is recommended that the heater be cleaned at least once a month and before o-season storage.Save the carton for o-season storage.

• Turn the heater OFF (

• Use a dry cloth to clean only the external surfaces of the heater. DO NOT USE WATER, WAX, POLISH OR ANY CHEMICAL SOLUTION.

• Before storing, clean the EnergySmart® Cool Touch Heater using the above-mentioned steps. Wrap the cord around its cord wrap

underneath the heater base. Pack the heater in its original carton and store it in a cool, dry place.

TROUBLESHOOTING

If your heater shuts o unexpectedly or fails to operate, one of your heater safety features may have been activated to prevent overheating.

• Be sure it is plugged in and that the electrical outlet is working.

• Check your EnergySmart® Thermostat setting. The unit may simply be o because you have reached your desired heat setting.

• Check for any obstructions. If you nd an obstruction, turn the heater OFF and unplug it. Allow the heater to cool completely,

then remove the obstruction. Wait at least 10 minutes, then re-plug the heater in and follow the OPERATION instructions.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY. DO
NOT RETURN THE HEATER TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING
YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE PRODUCT OR PERSONAL INJURY.

) and unplug it. Allow it to cool.

CONSUMER RELATIONS

Mail questions or comments to:

Kaz USA, Inc.
Consumer Relations Dept.
250 Turnpike Road
Southborough, MA 01772

PRODUCT SPECIFICATIONS

Models HZ-7200/7300 Series HZ-8000 Series
Unit dims 10.4” L x 7” W x 11.7” H 8.7” L x 6.3” W x 18.1” H
Amps 12.5
Unit Voltage 120V, 60Hz
Max Watts 1500
Max BTUs 5118
Operation Cost* To estimate the cost to operate this heater,

multiple the watts used times .001 to convert into a kilowatts
measure and multiple by your local kilowatt electric rate for
however long you run the heater.

3 YEAR LIMITED WARRANTY

You should rst read all instructions before attempting
to use this product.

A. This 3 year limited warranty applies to repair or

replacement of product found to be defective in
material or workmanship. This warranty does not
apply to damage resulting from commercial, abusive,
unreasonable use or supplemental damage. Defects
that are the result of normal wear and tear will not be
considered manufacturing defects under this warranty.

KAZ USA, INC. IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE ON THIS
PRODUCT IS LIMITED IN DURATION TO THE DURATION
OF THIS WARRANTY. Some jurisdictions do not allow

the exclusion or limitation of incidental or consequential
damages or limitations on how long an implied warranty
lasts, so the above limitations or exclusions may not
apply to you. This warranty gives you specic legal rights,
and you also may have other rights which vary from
jurisdiction to jurisdiction. This warranty applies only to
the original purchaser of this product from the original
date of purchase.

B. At its option, Kaz USA, Inc. will repair or replace this

product if it is found to be defective in material or
workmanship.

Call us toll-free at: 1-800-477-0457
E-mail: [e-mail]

Or visit our website at: www.kaz.com

Please be sure to specify a model number.

For example, if your electric rate is $.1196**per kilowatt hour
and you ran this heater in constant high mode (1500 watts) for
4 hours, it would cost you $.71 cents to run the heater (1500
watts x 4 hours x.001) x .1196kwp = .71 cents)

Note: Because the Low Settings do not require as much
electricity to operate, they are more energy ecient and may
be better options if you are concerned about the amperage
draw on a circuit when the heater is on the High (HI) setting.

*Calculation (Total Wattage x .001) x Cost per Kilowatt Hour =
Cost to operate

**Average Retail Price of Electricity to Ultimate Customer by End­Use, US Energy Information Administration, August 11, 2010

C. This warranty does not cover damage resulting from any

unauthorized attempts to repair or from any use not in
accordance with the instruction manual.

D. Return defective product to Kaz USA, Inc. with a brief

description of the problem. Include proof of purchase and
a $10 US/$15.50 CAN check or money order for handling,
return packing and shipping charges. Please include your
name, address and a daytime phone number.

You must prepay shipping charges. We suggest having

tracking or delivery conrmation.
Send to:

In U.S.:

Kaz USA, Inc.
Attn: Returns Department
4755 Southpoint Drive
Memphis, TN 38118 USA

In Canada:

Kaz Canada, Inc.
Attn: Returns Department
510 Bronte Street South
Milton, ON L9T 2X6 Canada

Please go to www.kaz.com and register your product under
the Customer Care Center and receive product information
updates and new promotional oers.

4 5