Honeywell HZ709 User Manual
IMPORTANT SAFETY
INSTRUCTIONS
WARNING – READ AND SAVE THESE
OPERATING AND SAFETY INSTRUCTIONS
BEFORE USING THIS HEATER. IF YOU DO
NOT UNDERSTAND THESES INSTRUCTIONS OR
PRODUCT LABELS PLEASE CALL
OUR CUSTOMER REPRESENTIVIES AT
(800) 477-0457 FOR ASSISTANCE BEFORE
USING THIS PRODUCT.
Warning – Failure to follow any of these safety
instructions could result in fire, injury or death.
YOUR RESPONSIBILITIES
Electrical appliances may expose people to
hazards that can cause severe injury as well as
death. The use of electrical products may create
hazards that include, but are not limited to,
injury, fire, electrical shock and electrical system
damage. These instructions are intended to
provide you with the information you need to
use the product and to avoid such hazards.
When using electrical appliances, basic
precautions should always be followed to
reduce risk of fire, electric shock, and injury
to persons including the following:
1. Warning – Read all instructions before using
this heater.
Oil-Filled Heaters
HZ-605/HZ-680/HZ-690 Series
HZ-709/HZ-710 Series
2. Warning – This heater is hot when in use.
To avoid burns, do not let bare skin touch
hot surfaces. If, provided, use handles
when moving this heater. Keep combustible
materials, such as furniture, pillows,
bedding, papers, clothes, and curtains at
least 3 feet (0.9 m) from the front of the
heater and keep them away from the sides
and rear.
3. Warning – Extreme caution is necessary
when any heater is used by or near children
or invalids, and whenever the heater is left
operating and unattended.
4. Warning – Always unplug heater when not
in use.
5. Warning – Do not operate any heater with
a damaged cord or plug or after the heater
malfunctions, has been dropped or damaged
in any manner. Discard heater or return
heater to authorized service facility for
examination and/or repair.
6. Warning – For residential use only.
7. Warning – Do not use outdoors.
8. Warning – This heater is not intended for
use in bathrooms, laundry areas and similar
indoor locations. Never locate heater where
it may fall into a bathtub or other water
container.
9. Warning – Do not run cord under carpeting.
Do not cover cord with throw rugs, runners,
or similar coverings. Do not route cord
under furniture or appliances. Arrange cord
away from traffic area and where it will not
be tripped over.
10. Warning – Connect to properly grounded
outlets only.
The Honeywell trademark is used by Kaz USA, Inc. under license from Honeywell International Inc.
Honeywell International Inc. makes no representation or warranties with respect to this product.
11. Warning – This heater is for use on
120 volts. The cord has a plug as shown in
Fig. 1, and an adapter, as shown, is available
for connecting three-blade grounding-type
plugs to two-slot receptacles. The green
grounding lug extending from the adapter
must be connected to a permanent ground
such as a properly grounded outlet box.
The adapter should not be used if a threeslot grounded receptacle is available. Do
not circumvent the safety features of the
grounding-type plug. Do not modify the
power cord.
12. Warning – This heater draws 12.5 amps
during operation. To prevent overloading a
circuit, do not plug the heater into a circuit
that already has other appliances working.
13. Warning – It is normal for the plug to feel
warm to the touch; however, a loose fit
between the AC outlet (receptacle) and plug
may cause overheating and distortion of
the plug. contact a qualified electrician to
replace loose or worn outlet.
14. Warning – To disconnect the heater, first
turn off the product, then grip the plug body
and pull it from the wall outlet. Never pull by
the cord.
15. Warning – Do not insert or allow foreign
objects to enter any ventilation or exhaust
opening as this may cause an electric shock
or fire, or damage the heater.
16. Warning – To prevent a possible fire, do not
block air intakes or exhaust in any manner.
Do not use on soft surfaces, like a bed, or
where openings may become blocked.
17. Warning – A heater has hot and arcing or
sparking parts inside. Do not use it in areas
where gasoline, paint or flammable liquids
are used or stored.
18. Warning – Use this heater only as
described in this manual. Any other use
not recommended by the manufacturer
may cause fire, electric shock, or injury to
persons.
19. Warning – Always plug heater directly into
a wall outlet/receptacle. Never use with an
extension cord or relocatable power tap
(outlet/power strip).
20. Warning – Never tamper with this product
or attempt to fix it. Any tampering with, or
modification of, this product can result in
serious injury, death, or fire. Risk of electric
shock. Do not open. No user serviceable
parts inside.
21. Warning – Do not remove product labels
that contain warnings or safety instruction.
22. Caution – The output of this heater may vary
and its temperature may become intense
enough to burn exposed skin. Use of this
heater is not recommended for persons with
reduced sensitivity to heat or an inability to
react to avoid burns.
23. Caution – Before cleaning, or storage, or
when not in use, turn the product’s controls
to the OFF position and unplug the heater
from the electrical outlet and allow to cool.
24. Caution – Place the heater on a firm, level,
open surface free from obstructions and
at least 3 feet (0.9 m) away from any
combustible materials. DO NOT use on an
unstable surface such as bedding or deep
carpeting. Be sure the heater is not in a
position where it may be tripped over by
small children or pets. The heater’s rubber
feet will hold it firmly in position.
25. Caution – If your home has aluminum
wiring have a licensed electrician check
your receptacle’s connections. When
using a 1500 watt heater, aluminum wire
connections can cause a safety issue.
26.
SAVE THESE
INSTRUCTIONS
2
IMPORTANT SAFETY INSTRUCTIONS REGARDING THE PLUG ON YOUR PRODUCT
Fig. 1
ELECTRICAL RATINGS
This product is rated 12.5 Amps
(1500 Watts) at 120 VAC, 60 Hz except
for the HZ-605C which is 8.33 Amps
(1000 Watts) at 120 VAC, 60Hz.
PRODUCT SPECIFICATIONS
Models HZ-709/HZ-710 Series, HZ-605C Series,
HZ-680/HZ-690 Series
Amps 12.5 8.33
Unit Voltage 120V, 60Hz 120V, 60Hz
Max Watts 1500 1000
Max BTUs 5118 3412
Unit dims 13.6” L x 9.5” W x 25.2” H (assembled) 10”L x 9.5”W x 25.2”H (assembled)
SET-UP WHEEL BASE ASSEMBLY
NOTE: DO NOT OPERATE THE HEATER WITHOUT THE WHEEL BASE
ASSEMBLIES IN PLACE. THE HEATER MUST ALWAYS BE USED IN AN
UPRIGHT POSITION. DO NOT OPERATE THE HEATER IF THE WHEELS
ARE NOT ASSEMBLED CORRECTLY.
• Make sure the heater is unplugged and in the OFF position.
• Turn the heater upside down to install wheels.
• Push wheels into each wheel base pin, until you hear them snap into
position.
• While the heater is still upside-down, position the wheel base assemblies
between the end ns. Attach them to the U-bolts on the heater and
tighten using the wing nuts provided (Fig. 2).
• Turn heater right-side up. Your heater is now ready for use.
• Place the heater on a rm, level surface free from obstructions, and at
least 3ft. (0.9m) away from any wall or combustible material.
If the controls are located at the bottom and the Honeywell logo
is upside down you have installed the wheels incorrectly (Fig. 3).
Fig. 2
Wheel Base
(Bottom of Unit)
U-bolts
Correct Incorrect
Wheel Base Pin
Wing Nuts
NOTE: These heaters contain oil that is permanently sealed and will
never require relling or replacing.
NOTE: THESE MODELS MAY TAKE UP TO SEVERAL MINUTES TO REACH
NORMAL OPERATIONAL TEMPERATURE.
Fig. 3
3
HZ-680 SERIES OPERATION
• With the power switches in the OFF position, plug the heater into a 120V outlet.
Fig. 4a
• Never leave an operating unit unattended.
• Turn the thermostat control fully clockwise to its highest setting.
• This heater has 3 levels of heating. Press I for Low setting. Press II for Medium setting and press
Adjustable
Thermostat
both I and II for the High setting (Fig. 4a: l for 600W/LOW, Fig. 4b: ll for 900W/MED, or Fig.
4c: III for 1500W/HIGH). You can select the proper setting to accommodate your comfort level.
Because the Low and Medium heat settings do not require as much electricity to operate, they
are more energy ecient and may be better options if you are concerned about the amperage
Power
Level
Switches
draw on a circuit when the heater is in the High setting.
• Turn the power switches to ON. They will illuminate, and the heater is now in use.
• When the room reaches a comfortable temperature, slowly turn the adjustable thermostat
knob counter-clockwise until the heater goes o. This is the point where the thermostat
setting equals the room temperature. At this setting, the
thermostat will automatically maintain your desired room
Fig. 4b Fig. 4c
temperature by cycling the heater on and o. The power
indicator will remain on when the unit is cycling on and o.
Just the heating element will actually turn on and o.
• Turning the thermostat clockwise will always increase the
“set” temperature; turning the thermostat counter-clockwise
will decrease the “set” temperature.
• Turn the power switches to OFF (
) and unplug heater when
nished using the heater.
NOTE: THIS HEATER WILL COOL DOWN SLOWLY AFTER THE POWER IS SHUT OFF. BEFORE MOVING THE HEATER USING THE
BUILT IN HANDLE, ALLOW THE HEATER TO COOL.
HZ-605 SERIES/HZ-690 SERIES OPERATION
• With the power control knob in the OFF (
) position, plug the heater into
a 120V outlet.
• Never leave an operating unit unattended.
• Turn the heater ON by turning the power control knob clockwise to the desired
position. The power light will illuminate. Turning the unit on High and leaving the
unit on this setting for approximately 1 hour will speed up the heat output.
• You can then select the proper setting to accommodate your comfort level. This
heater is equipped with three dierent heat settings (Fig. 5).
The HZ-690 Series, the Low setting (
) uses 900 watts of power and the High setting ( ) uses 1500 watts
setting (
) uses 600 watts of power, the Medium
of power.
The HZ-605 Series uses 400 Watts of power on the Low setting (
of power on the Medium setting(
setting (
).
) and 1000 watts of power on the High
), 600 watts
• Turn the thermostat control fully clockwise to its highest setting.
• Because the Low and Medium heat settings do not require as much electricity
to operate, they are more energy ecient and may be better options if you are
concerned about the amperage draw on a circuit when the heater is in the
High setting.
4
Fig. 5
Power
Control
Power
Indicator
Light
Adjustable
Thermostat
HZ-605 SERIES/HZ-690 SERIES OPERATION (Continued)
• When the room reaches a comfortable temperature, slowly turn the adjustable thermostat knob counter-clockwise until the
heater goes o. This is the point where the thermostat setting equals the room temperature. At this setting, the thermostat
will automatically maintain your desired room temperature by cycling the heater on and o.
• Turning the thermostat clockwise will always increase the “set” temperature; turning the thermostat counter-clockwise will
decrease the “set” temperature.
• Turn the power control knob OFF (
) and unplug heater when nished using the heater.
NOTE: THIS HEATER WILL COOL DOWN SLOWLY AFTER THE POWER IS SHUT OFF. BEFORE MOVING THE HEATER, USING THE
BUILT IN HANDLE, ALLOW THE HEATER TO COOL.
HZ-709/HZ-710 SERIES OPERATION
STEP 1: PO WER
• Press the Power button to start the heater. Your heater will automatically start on
High power, continuous run. The display will be illuminated and will reect the
current room temperature (Fig. 6).
• To turn your heater OFF simply press the Power button again.
• Never leave an operating unit unattended.
STEP 2: HE AT OU TP UT
• This heater is equipped with three dierent heat settings. The Low setting (—)
uses 600 watts of power, the Medium setting (
the High setting (———) uses 1500 watts of power.
You can select the proper setting to accommodate your comfort level. Because
the Low and Medium heat settings do not require as much electricity to operate,
they are more energy ecient and may be better options if you are concerned
about the amperage draw on a circuit when the heater is in the High setting.
• To change your heat setting, press the heat setting control button up or down
(Fig. 7).
• Once you have selected your desired power level the display will go back to
showing the current room temperature after 3 seconds.
—
) uses 900 watts of power and
—
STEP 3: TIME R CO NTRO L – AUTO S HUT- OFF
• You can set your timer for up to 18 hours automatic shut-o.
This function should only be used if you desire that the heater
be automatically shut-o after a certain period of time.
• Press the Timer button up or down to set the heater operation time
(Fig. 8). You can set the timer in increments of 1 hour up to 18 hours.
• When the display indicates your desired time, the display will
revert back to showing the current room temperature after 3 seconds.
• The heater will automatically turn-o when the set time has elapsed.
NOTE: If you wish to change your timer setting or check to see how much time is
left, simply press the timer button once and it will show you the time left. If you
want to change the time remaining, continue to push the button up or down until
you have reached your desired time. Again, after 3 seconds the display will revert
to showing the current room temperature.
Fig. 6
Desired
Temperature
Light
Heat Setting
Control
Fig. 7
Fig. 8
Temperature
Control
Timer
Control
5
HZ-709/HZ-710 SERIES OPERATION (Continued)
STEP 4: SE T TEM PER ATU RE
• You can set your desired temperature level in 1° increments anywhere from
45° to 85° F.
• To set your desired temperature, press the temperature button.
• When the display indicates your desired temperature, the display will revert
back to showing the current room temperature after 3 seconds.
• Once you have set your desired temperature the unit will operate under this
desired setting until the unit is turned o.
• When your desired room temperature has been reached your unit will shut o
and the house icon on the top of your display will illuminate (Fig. 9). It will
stay illuminated until the room temperature decreases below your desired
temperature level, at which time your unit will turn back on.
NOTE: If you wish to change your temperature setting or check to see what you set, simply press the temperature button once and
it will show you the set temperature. If you want to change it, continue to push the button up or down until you have reached your
new desired temperature. Again, after 3 seconds the display will revert to showing the current room temperature.
Fig. 9
FA HR EN HEI T/C ELS IUS SET TI NG
This heater oers the option to read the temperature setting in either Fahrenheit or Celsius.
• The heater will default to the Fahrenheit setting when turned on.
• The heater can only be changed from Fahrenheit to Celsius when initially turned on.
• After turning the heater on the letter F will briey be displayed on the LED screen. While the F is displayed press the
temperature button down. At this point the letter “C” will be displayed and the heater temperature settings will be
displayed in Celsius.
NOTE: THIS HEATER WILL COOL DOWN SLOWLY AFTER THE POWER IS SHUT OFF. BEFORE MOVING THE HEATER, USING THE
BUILT IN HANDLE, ALLOW THE HEATER TO COOL.
TIP-OVER SWITCH FEATURE (HZ-709/HZ-710 SERIES ONLY)
This heater is equipped with a tip-over switch that disables the heater if it is tipped sideward. To restore power to the heater:
• Place the heater in the upright position.
• Press the Power button.
• The LED display will activate and normal operation will resume.
TROUBLESHOOTING
If your heater shuts o unexpectedly:
• Be sure the heater is plugged in and that the electrical outlet is working.
• Check your temperature setting. The heater may simply be o because you
have reached your desired temperature setting or your timer setting may
have elapsed.
• Check to make sure your heater is assembled correctly. If your heater is
assembled and operating incorrectly it could result in a burning odor and
smoke (Fig. 10).
For more troubleshooting tips, visit our website at: www.kaz.com
6
Correct Incorrect
Fig. 10
TROUBLESHOOTING (Continued)
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY. DO
NOT RETURN THE HEATER TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING
YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE PRODUCT OR PERSONAL INJURY.
IF YOU HAVE ANY QUESTIONS REGARDING THIS HEATER, PLEASE CALL OR WRITE:
Kaz USA, Inc.
250 Turnpike Road, Southborough, MA 01772
Toll Free: 1-800-477-0457
CLEANING AND STORAGE
• Consumer Relations Department
• E-mail: consumerrelations@kaz.com
CLEA NIN G
We recommend that the heater be cleaned at least once a month and before o-season storage.
• Turn the heater OFF and unplug it. Allow it to cool completely.
Use only a dry cloth to clean the external surfaces of the heater. DO NOT USE WATER, WAX, POLISH, OR ANY CHEMICAL SOLUTION.
•
STORAGE
• Clean your heater using he above mentioned steps.
• Wrap the cord around the cord wrap on the unit, place it in its original box and store in a cool, dry area.
3 YEAR LIMITED WARRANTY
You should rst read all instructions before attempting
to use this product.
A. This 3 year limited warranty applies to repair or
replacement of product found to be defective in material
or workmanship. This warranty does not apply to damage
resulting from commercial, abusive, unreasonable use or
supplemental damage. Defects that are the result of normal
wear and tear will not be considered manufacturing defects
under this warranty.
KAZ USA, INC. IS NOT LIABLE FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS
LIMITED IN DURATION TO THE DURATION OF THIS
WARRANTY.
Some jurisdictions do not allow the exclusion or limitation
of incidental or consequential damages or limitations on
how long an implied warranty lasts, so the above limitations
or exclusions may not apply to you. This warranty gives you
specic legal rights, and you also may have other rights
which vary from jurisdiction to jurisdiction. This warranty
applies only to the original purchaser of this product from
the original date of purchase.
B. At its option, Kaz USA, Inc. will repair or replace this product
if it is found to be defective in material or workmanship.
Thereafter, while within the warranty period defective
product may be returned to Kaz USA, Inc.
C. This warranty does not cover damage resulting from any
unauthorized attempts to repair or from any use not in
accordance with the instruction manual.
D. Return defective product to Kaz USA, Inc. with a brief
description of the problem. Include proof of purchase and
a $10 US/$15.50 CAN check or money order for handling,
return packing and shipping charges. Please include your
name, address and a daytime phone number.
You must prepay shipping charges. We suggest having
tracking or delivery conrmation. Send to:
I
n U.S.A.
Kaz USA, Inc.
Attn: Returns Department
4755 Southpoint Drive
Memphis, TN 38118
USA
In Canada:
Kaz Canada, Inc.
Attn: Returns Department
510 Bronte Street South
Milton, ON L9T 2X6
Canada
Please go to www.kaz.com and register your product under
the Customer Care Center and receive product information
updates and new promotional oers.
©2011 Kaz USA, Inc. All Rights Reserved.
US Patent No. 7,403,702
P/N: 31IM0709192
7
8
Loading...