Honeywell HY013 User Manual

DY-012_HY-013_OM.qxd 10/17/08 10:47 AM Page 1

Owner’s Manual

TOWER FAN

Model DY-012 Series Model HY-013 Series

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS FAN

When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Use this fan only as described in this

manual. Other use not recommended as it may cause fire, electric shock or injury to persons.

2. This product is intended for household use

ONLY and not for commercial, industrial or outdoor use.

3. To protect against electric shock, do not

place fan in window, immerse unit, plug or cord in water or spray with liquids.

4. This appliance has a polarized plug (one

blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fitfully in the outlet, reverse the plug. qualified electrician. defea

5. Close supervision is necessary when any

appliance is used by or near children.

urn the fan OFF and unplug the fan from

6. T

If it still does not fit,

Do not attempt to

t this safety feature.

contact a

the outlet when not in use, when moving the fan from one location to another and before cleaning.

7. To disconnect the fan, first turn the unit

OFF, grip the plug and pull it from the wall outlet. Never pull the plug by the cord.

8 Do not operate the fan in the presence of

explosive and/or flammable fumes.

9. Do not place the fan or any parts near an

open flame, cooking or other heating appliance.

10. Do not operate the fan with a damaged

cord or plug or if the product malfunctions, is dropped or damaged in any manner (see warranty).

11. Avoid contact with moving fan parts.

12. The use of attachments not recommended

by the manufacturer may be hazardous.

13. Place the fan on a dry level surface.

14. Do not hang or mount fan on a wall or

ceiling.

15. Do not operate if the fan housing is

damaged.

16. A loose fit between the AC outlet

(receptacle) and plug may cause over heating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlet.

ARNING: T

W or Electric Shock, With Any Solid-State Speed Control Device.

o Reduce The Risk of Fire

Do Not Use This F

DY-012_HY-013_OM.qxd 10/17/08 10:47 AM Page 2

DY-012 SERIES ASSEMBLY INSTRUCTIONS

NOTE: Remove all contents from the box being careful not to discard

the manual and hardware needed for assembly.A phillips head screw driver ( ) is required for assembly and is not included with the fan purchase.

A. Base Assembly

• Gently turn the fan upside down.

• Place the power cord through the recessed channel located in the center of the rear base assembly (Fig 1).

• Align the rear and front base assembly and firmly snap together by pushing the 4 round extrusion into the adjacent circles of the connecting pieces (Fig 2).

B. Securing the Tower Fan to the Base

• Using the 3 (M5 x 12) screws and phillips head screw driver ( ) secure the base into the bottom portion of the fan housing by aligning the 3 screw holes on the base with the 3 screw holes on the bottom of the fan housing (Fig 3).

• Gently pull any slack out of the power cord and place the cord securely in the power cord holding bracket (Fig. 4).

• Place the fan right side up. Your fan is now ready for use.

Fig. 3

Fig. 1

Fig. 2

Fig. 4

DY-012 SERIES OPERATION INSTRUCTIONS

• Be sure your fan is in the OFF position by pressing

Fig.

Fig. 6

the off button. ( )

• Place the fan on a level and dry surface.

• Plug the power cord into a polarized 120 Volt AC wall outlet.

•

To operate, press the appropriate speed control option: High ( ), Medium ( ), or Low ( ) (Fig. 5).

• To activate or disengage the fan oscillation, press the oscillation button ( ) (Fig 6). To turn the fan OFF ( ) press the Off button once.

•

DY-012_HY-013_OM.qxd 10/17/08 10:47 AM Page 3

HY-013 SERIES ASSEMBLY INSTRUCTIONS

NOTE: Remove all contents from the box being careful not to discard the manual and hardware needed for

assembly.A phillips head screw driver ( ) is required for assembly and is not included with the fan purchase.

A. Pedestal Assembly

• Place the power cord through the center of the front and rear pedestal assemblies with the screw hole openings facing towards the fan.

• Align the front and rear pedestal assembly and firmly snap together (Fig 7).

B. Securing the Tower Fan to the Pedestal

• Gently turn fan upside down.

• Line up the 3 screw holes on the pedestal with the 3 screw holes on the bottom of the fan housing. Use the 3 (M5 x 12) screws included in the box and a phillips head screw driver ( ) to secure the pedestal to the fan housing (Fig. 8).

C. Base Assembly

• With the fan in the upside down position, pass the power cord through the recessed slot located in the center of the rear base assembly (Fig 9).

• Align the rear and front base assembly and firmly snap together by pushing the 4 round extrusion into the adjacent circles of the connecting pieces (Fig 10).

D. Securing the Tower

Fig. 9

Fan to the Base

• Align the 3 screw holes in the bottom of the pedestal with the 3 screw holes located on the base. Using the 3 (M5 x 12) screws and phillips head screw driver ( ), secure the base into the bottom portion of the fan housing (Fig 11).

• Place the power cord through the cut out on the bottom of the base. Gently pull any slack out of the power cord and place the cord securely in the power cord holding bracket

ig. 12).

(F Place the fan right side up.

•

Fig. 11 Fig. 12

Your fan is now ready for use.

Fig. 7

Fig. 8

Fig. 10

DY-012_HY-013_OM.qxd 10/17/08 10:47 AM Page 4

HY-013 SERIES OPERATION INSTRUCTIONS

• Be sure your fan is in the OFF position by pressing the off button. ( )

• Place the fan on a level and dry surface.

• Plug the power cord into a polarized 120 Volt AC wall outlet.

• To operate, press the appropriate speed control option: High ( ), Medium ( ), or Low ( ) (Fig. 13).

• To activate or disengage the fan oscillation, press the oscillation button. ( ) (Fig 14).

• Operate the automatic shut-off timer feature by turning the timer knob to the desired setting of 10 to 120 minutes (Fig 15).

• To turn on the fan after automatic shut-off, turn

Fig. 14

the knob counterclockwise to the ON position

•

To turn the fan off press the Off button once.

()

Fig. 13

Fig. 15

DY-012_HY-013_OM.qxd 10/17/08 10:47 AM Page 5

CLEANING AND STORAGE

• Unplug the fan before cleaning.

• Use only a soft, damp cloth to gently wipe the outside surface of the fan.

•

DO NOT immerse the fan in water and never allow water to drip into the motor housing. DO NOT use gasoline, paint thinner or other chemicals to clean the fan.

•

• Gently wipe the grilles with a cloth. To clean between the grilles we recommend using a pipe cleaner, flexible dustwand, vacuum cleaner or compressed air to gently remove dust.

DO NOT IMMERSE THE FAN IN WATER AND NEVER ALLOW WATER TO DRIP INTO THE MOTOR HOUSING. DO NOT USE GASOLINE, PAINT THINNER,OR OTHER CHEMICALS TO CLEAN THE FAN.

• For storage, clean the fan carefully as instructed. Store the fan in the original packaging or cover the product to protect it from dust. Store the fan in a cool, dry place.

CONSUMER RELATIONS

Mail questions or comments to:

Kaz, Incorporated Consumer Relations Dept. 250 Turnpike Road Southborough, MA 01772

Call us toll-free at: 1-800-477-0457 E-mail: consumerrelations@kaz.com

Or visit our website at:

www.kaz.com

Please be sure to specify a model number.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY. DO NOT RETURN TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE.

DY-012_HY-013_OM.qxd 10/17/08 10:47 AM Page 6

1 YEAR LIMITED WARRANTY

You should first read all instructions before attempting to use this product.

This 1 year limited warranty applies to repair

or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty.

KAZ IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

B. At its option, Kaz will repair or replace this

product if it is found to be defective in material or workmanship.

C. This warranty does not cover damage resulting

from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.

D. Return defective product to Kaz, Incorporated

with a brief description of the problem. Include proof of purchase and a $10 US/$15.50 CAN check or money order for handling, return packing and shipping charges. Please include your name, address and a daytime phone number.

You must prepay shipping charges. We suggest having tracking or delivery confirmation. Send to:

In U.S.:

Kaz, Incorporated Attn: Returns Department 4755 Southpoint Drive Memphis, TN 38118 USA

In Canada:

Kaz Canada Inc. Attn: Returns Department 510 Bronte Street South Milton, ON L9T 2X6 Canada

Please go to

www.kaz.com and register your

product under the Customer Care Center and receive product information updates and new promotional offers.

P/N: 31IMY013190

+ 12 hidden pages