HX3
Wearable Computer
With Microsoft Windows®CE 5.0 Operating System
Quick Start Guide
HX3-QS Rev A
4/12
HX3 Rugged Voice Computer
Components - Front
Components - Back
Attach Audio/Power Cable to HX3
Connect Battery and AudioCable
Trigger Rotation
Attach Ring to Finger
Attach Ring Cable to HX3
Voice Pouch, Headset and Ring Scanner
Alternative Battery Placement
Scanning a Bar Code
Desktop Cradle
Battery Multi-Charger
Remove Ring Strap Module
Remove Trigger Module
Replace Ring Strap Module
Replace Trigger Module
Setting up the HX3
Please have the following Information available before setting up your HX3:
l Network ID (SSID) of the Acc ess Point
l WEP key or LEAP authentication credentials
1. Connect a fully charged battery to the HX3.
2. Press the Power button.
3. Connect via ActiveSync
4. Copy LXEConnect f iles to PC.
5. Inst all and launch LXEConnect
6. Accept the EULA.
7. Set the date and time.
8. Edit the radio parameters.
9. Perform a reboot.
Bluetooth and HX3
Please refer to the HX3 Reference Guide for information when using the HX3 with
Bluetooth.
ActiveSync
Installing ActiveSync on D esktop/Laptop
ActiveSync (version 4.5 or higher f or Windows XP desktop/laptop computers) must be
resident on the host (desktop/laptop) computer. Windows Mobile Device Center is
required for a Windows Vista/Windows 7 desktop/laptop computer. ActiveSync and
Windows Mobile Device Center for the PC are available from the Microsoft w ebsite.
Follow Microsoft's instruct ions to locate, download and install ActiveSync or Windows
Mobile Devic e Center on your desk top/laptop.
ActiveSync using USB-Client Co nnection
The only connection type is USB Client.
1. Connect the HX3 end of the cable to the connector on t he bott om of the HX3.
2. Connect the USB t ype A connector on the I/O cable t o a USB port on a PC or
laptop.
ActiveSync starts automatic ally when the USB cable is connected.
When the HX3 loses connection, the connection t o ActiveSync is lost. Disconnect the
PC end of the cable and re-connect.
Please refer to the HX3 Reference Guide for ActiveSync information.
LXEConnect
Install LXEConnect
1. Establish an Act iveSync connection between the HX3 and a laptop/desktop.
2. Select Explore (Act iveSync) or File Management (Windows Mobile Device
Center) f rom the PC interface.
3. Browse to the \ System\LXEConnect folder on the H X3 using the explorer
dialog box.
4. Copy the LXEConnect.msi and Setup.exe files from the HX3 t o t he PC.
5. Close the explorer dialog box.
6. Execute the Setup.exe file t hat was copied to t he PC.
7. Follow the on screen prompts to install LXEConnect.
Using LXEConnect
1. Establish an Act iveSync connection to the HX3 if one does not exist .
2. Launch LXEConnect from the PC by s electing Start > Programs > LXE >
LXEConnect.
3. LXEConnect launches and displays t he HX3 desktop.
4. The HX3 can be configured from the LXEConnect window. Input from the
PC's keyboard and mouse are recognized as if t hey were att ached to t he
HX3.
5. Click t he OK button to dismiss the About CERDisp dialogbox. The dialog box
automatically times out after approximately 30 seconds if no action is taken.
6.
If any parameter c hanges were made, warmboot t he HX3 by clicking >
Run. Type warmboot and c lick OK.
7. Select Fil e > Exit or click the X in the upperright hand corner to close
LXEConnect and then disconnect the Act iveSync sess ion.
Warmbooting the HX3 terminates the ActiveSync connection. To make additional
changes to t he HX3, reconnect the ActiveSync cable and launch LXEConnect again.
Rebooting the HX3
Using the Start menu, s elect Start > Run and type warmboot in the t ext box. Press
Enter.
When the HX3 is booting, there may be small delays while the wireless client connects,
applications launch, remote management completes and Bluetooth devices connect.
Setting Up the Radio
If the access point uses an authentication protocol (WEP, LEAP, etc. ), your radiomust
use the same authentication. Please contact your I T department for WEP keys or LEAP
credentials. Please refer to the HX3 Reference Guide for information on using WPA.
1. Tap Start > Programs > Summit > SCU OR tap the Summit Client Utility
icon on the desktop.
2. Tap the A dmin Login button and enter t he password (default = SUMMIT).
3. Tap the Profile t ab and make sure the Default profile is selected.
4. Select SSID and enter your SSID v alue.
5. If t he acc ess point is using WEP, select WEP from t he Encryption pull down
list.
6. Tap the WEP keys/PSKs button and enter the WEP Key(s) and tap OK. Skip
to step 12.
7. If t he acc ess point is using LEAP, select LEAP from the EAP Ty pe pull down
list.
8. Select WEP EAP from the Encryption pull down list.
9. If t he Cisco/CCS certified AP is configured f or open authentication, set the
Auth Type radio parameter to Open.
10. If the AP is configured for network EAP only, set the Auth Type radio
parameter to LEAP.
11. Tap t he Credentials butt on and enter the Us er Name and Password.
12. Tap t he Commit button t o save the radio configuration.
13. Tap t he Main tab. Wait for a radio connected message.
14. Tap t he Admin Logout butt on when finished.
15. Reboot t he HX3.
Please refer to the Radio Mode parameter in the HX3 Reference Guide. I t is important
that this parameter setting corresponds to t he Acc ess Point to which the HX3
connects.
Disclaimer
Honeywell International Inc. (“HII”) reserves the right to make changes in specifications
and other information contained in t his document without prior notice, and the reader
should in all cases consult HII to determine whether any such changes have been
made. The information in this publication does not represent a commitment on the part
of HII.
HII s hall not be liablefor technical or editorial errors or omissions contained herein; nor
for incidental or consequential damages resulting from the furnishing, performance, or
use of this material.
This document contains proprietary information that is protected by copyright. All rights
are reserved.
© 2007-2012 Honeywell International I nc. All rights reserved.
Other product names or marks mentioned in this document may be t rademarks or
registered trademarks of other companies and are the property of their respective
owners.
Web Address: www.honeywellaidc.com
Patents
For patent information, please refer to www.honeywellaidc.com/patents .
Technical Assistance
Contact information for technical support, product service, and repair can be found at
www. honeywellaidc.com.
Limited Warranty
Refer to www. honeywellaidc.com/warranty _information f or your product’s warranty
information.
User Documentation
To downloadthe H X3 user documentation go to www.honeywellaidc.com.
Loading...