Honeywell ExitView Installation Manuals

ExitView® Height Strip Camera Installation Guide

The ExitView Height Strip Camera is designed for installation either on a door frame (recommended) or wall mounted as
close to the door as possible.

Unpacking the Kit

Before you begin the installation, make sure you have the following kit contents:

• Metal housing with camera* and camera cables
(barrel connector and BNC video connector)

• Acrylic height strip

• 12 V power supply, with barrel connector end
(North American model only)

* Camera lens is prefocused at the factory and does not require adjustment.

Installing the Height Strip Camera

1. Place a horizontal mark on the door frame or wall at the 5 ft. (1.5 m) height level
from the floor.

2. Drill a 5/8 in. (16 mm) hole exactly 3 in. (76.2 mm) above the horizontal 5 ft. (1.5
m) mark.

3. Thread the camera cables through the hole.

4. Attach the 12 V power supply to the barrel connector cable of the camera; then

camera

4 x 2 in. slots

5/8 in. cable

connection hole

5 ft. mark (1.5 m)

attach the BNC video connector cable to the video connection, using a standard
video cable (75 ohm coaxial is recommended).

Note The barrel connector is center positive. The camera will not work if the

connection is made to center negative.

5. Slide any extra cable length back into the door frame or wall.

6. Hold the metal housing against the door frame or wall and align the 5 ft. (1.5 m)
marker hole on the housing with the 5 ft. (or 1.5 m) horizontal mark.

7. Fasten the metal housing securely through the four 2 in. (50.8 mm) slots using
the self-tapping screws and washers provided.

8. Remove the protective covering from the acrylic strip. Use a lint-free cloth to
remove any excess adhesive.

9. Insert the acrylic strip into the housing from the bottom.

10. Attach the bottom end plate using the end cap screws provided.

11. Power up the camera and test the video connection.

• Hardware fastening kit (recommended for most door
frames):

• Four #12 Type A self-tapping screws and washers

• Bottom end plate

• Two end cap screws

Document No. 900.0346 – Rev 1.01 – 03/07

Specifications

Video Standard: NTSC
Model No.: HSB37NB (black, black window), HSB37NM (black, metric),

HSB37NS (black, imperial), HSS37NB (silver, black window),
HSS37NM (silver, metric), HSS37NS (silver, imperial)

Imager Format: 1/3 in. CCD
Lens: 3.7 mm semi pinhole, F2.0
Video Output: 1.0 V p-p @ 75 Ohms
Resolution: 350 TV lines
Light Sensitivity: 0.9 lux @ F2.0
Electronic Iris: 1/60 to 1/100,000 sec
S/N Ratio: 50 dB (AGC off)
Backlight

Compensation:
White Balance: AWB
Input Voltage: Regulated 12 VDC power supply included (120 VAC input) UL Listed
Power Consumption: 1.8 W
Temperature

Operating:
Storage:

Video Cable: Use minimum type RG-59 copper clad steel core, 95% braided shield
Power Cable: Use 18 gauge stranded wire. (Do not run more than 100 feet (30.5 m)

Weight: 1.4 lb (0.65 kg)
Dimensions (w x h x l): 1.9 x 1.2 x 34.25 in. (48 x 29 x 870 mm)
Enclosure: Extruded aluminum housing (available in silver or black)
Height Strip: Scratch coated acrylic

* Specifications subject to change without notice. All dimensions and weights are approximate.

Automatic

-14°F to 122°F (-10°C to 50°C)

-4°F to 140°F (-20°C to 60°C)

from transformer.)

Regulatory Notice - FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

www.honeywellvideo.com

+1.800.796.CCTV (North America only)

[e-mail]

Document 900.0346 – Rev 1.01 – 03/07

© 2007 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written
permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell
Video Systems cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject
to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.