Honda XR 600R Service Manual Kapitel06
Specifications and Main Features
- The activation of compression begins and the decompressor comes to life at +500 100kpa (5 +1 kg cm squared.)
- At + 1400 100kpa(14 +1 kgcm squared) the compression decompressing function is not set off.
- The tilting angle of the cam for an intake operation: 31 155-31 315 mm (1 2266-1 2329inches).
- While for an exhaust operation while the cm gets tilted to another angle: 31 091-31 251 mm (1 2241-1 2304inches).
- Movement error during the operation/rotation of camshaft is 0.40 mm along with the distance of 0.016 inches.
- The external diameter of a rocker arm shaft is as follows: 11 466-11 484(in mm) along with (0 4514-0 4521in).
- In the other hand the intake sub rocker arm shaft has an external bearer shaft diameter of 7 972-7 967 (in mm) and (0.3137-0.3139in)
- The diameter of the exhaust arm is smaller than all of the above with (0.2744-0.2745in) and an external diameter of 6 972-6 969 mm.
- The internal diameter of the rocker arm varies from the above ranges as well and is now ----cm. 11 500 11 518(mm) and 0.4528 0.4535(in).
- Looking closely at the valve spring for a particular role such as the inner length of the spring is 1 240 in and 35.1 mm.
- For a lesser role the valve spring outer length is almost 1 417 in with a length of 36 mm.
- Thus the intake and exhaust valves stem for cylinder suits best in the range of (0.2589-0.2594in) and (0.2582-0.2589in)
- Rounding up the valve guide measurements varies between 6.600 6.615 mm and 0.2598 0.2421.
- The valve face width varies from 1.20-1.85 and 1.20 ranging from an intake valve to an exhaust with a wide range 1.85.
- The warpage for a cylinder of an inhaler can go up to 0.10mm while the side diameter can reach 0.004inch.
- Moreover the valve seat diameter goes up to 1.4 in mm ranging from 1.2 mm.
- At first the embedded N shaped bolt head goes through a cyclindre head bolt that gaves off a torque of 36N-m which would range from 3.6kg m, and 26ftlb.
- Additionally the embedded N shaped bolt head had a round bolt that relaxed a torque of 28 N-m due it been attached to he rocker arm, it was embedded with 2.8 kg m, and amounted near 20ft lb.
- Tools resorted to towards the end of the work include knock pin puller set and valve spring.
Frequently Asked Questions
Q: Can you briefly tell me the compression set in the decompressor on condition?
A: For conditions where the decompressor is activated, the breaking pattern is set at a standard compression of 500 + 100 kPa (5 + 1 kg/cm²).
Q: For the camshaft, what is the maximum lift that can be obtained while turning anticlockwise and what is its tolerance range?
A: The appropriate range on the intake camshaft lift is 31.155—31.315 mm (1.2266—1.2329 in).
Q: What type of tool do I use to check for warpage in the cylinder head?
A: For wliarps checking in the cylinder, heads use a straight edge and feeler gauge with a service limit of 0.10 mm (0.004 in).
Q: Can you tell me the torque specifications of the bolts for the cylinder head?
A: The standard torque for a cylinder head for such a device is 36 N-m (3.6 kg-m, 26 ft-lb)
Q: In a perfect world, how many hours should the valve seat persenine and resurfacing be done?
A: As a matter of fact, the valve seats can be resurfaced every time new valve guides are installed.
User Manual
Loading...