Using the navigation system while driving can take your
attention away from the road, causing a crash in which you
could be seriously injured or killed.
Only operate system controls when the conditions permit you
to safely do so.
WARNING
QRG
InformationProvidedby:
The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd., reserves the right,
however, to discontinue or change specifications or design at any time without notice and without incurring any obligation.
Accessories Precautions
The GPS antenna is located in the dashboard. Metallic front or side window tinting can seriously degrade or obstruct GPS reception.
Signal noise from devices such as radar detectors, vehicle tracking devices, remote starters, and additional amplifiers can disrupt the navigation system. If you
install any such item, install it away from the navigation display and antenna.
Important Safety Information
Avoid focusing on the screen or manually operating the system controls while driving.
Certain on-screen controls are disabled when driving, but most of the audible instructions and voice commands continue to function. Pull to the side of the road
if you need to devote more attention and time to look at the screen or access additional menus.
Route guidance may conflict with street closures, road construction, detours, and out-of-date map data.
The system itself may also have limitations. Verify route information by carefully observing roads, signs, and signals. Always use your own judgment and obey
traffic laws.
Index
Home
System Limitations P. 174
2
NOTICE
This vehicle’s navigation display, if so equipped, includes mercury-containing components. Upon removal, please reuse, recycle, or dispose of as hazardous waste.
Clean the screen with a soft, damp cloth. You may use a mild cleaner intended for use on navigation screens.
QRG
InformationProvidedby:
2 System Setup P. 17
Start-up 18Voice Control System 20Interface Settings 22Personal Information 30
Routing & Guidance 40Clock Adjustment 47Vehicle 50Data Reset 53
2 Navigation P. 55
Entering a Destination 56Calculating the Route 77Driving to Your Destination 80 Map Menu 85
Changing Your Route 99Changing Your Destination 106 Resuming Your Trip 110
2 Audio P. 111
Audio System 112Playing FM/AM Radio 114Playing a Disc 119Playing an iPod® 123
Playing a USB Flash Drive 127 Playing Bluetooth® Audio 131Adjusting the Sound 134Audio Remote Controls 135
Contents
Quick Reference Guide
System Setup
Navigation
Audio
P.2
P.17
P.55
P.111
Index
Home
2 Bluetooth® HandsFreeLink® P. 137
Bluetooth®
HandsFreeLink® 138
Phone Setup 149Making a Call 150Receiving a Call 153HFL Menus 154
Pairing a Phone 140Setting Up Speed Dialing 145Editing Phone
Information 148
2 Other Features P. 157
Information Functions 158
2 Troubleshooting P. 159
Troubleshooting 160Error Messages 166
2 Reference Information P. 171
System Initialization 172System Limitations 174Customer Assistance 176Legal Information 179
2 Voice Commands P. 183
Voice Commands 184
Navigation Key
QRG
Quick Reference Guide
TOC
Chapter Table of Contents
Index
Index
Home
BookTable of Contents
Voice
Commands
Bluetooth
® HandsFreeLink®
Other Features
Troubleshooting
Reference Information
Voice Commands
Index
P.137
P.157
P.159
P.171
P.183
P.194
Store home addresses(P36)
Register
2 home addresses.
Store contacts(P31)
Store up to
200 contacts in 2 address books.
Enter destination(P56)
Select your destination using
11 methods.
Select route(P78)
Set route preferences and select one of
3 routes.
Track route(P80)
Follow your route in real-time with voice guidance.
Avoid certain areas(P100)
Set streets and areas to detour around.
Add waypoints(P101)
Add up to
4 “pit stops” along your route.
QRG
InformationProvidedby:
Quick Reference Guide - 2013 Fit
Overview—Functions at a Glance
Index
Home
2
Navigation
You can select any place/landmark as a destination by using voice control or the touch screen. The navigation
system gives you turn-by-turn driving directions to your destination.
Audio
AM/FM Radio(P114)
Compact Disc(P119)
iPod®(P123)
USB Flash Drive(P127)
Bluetooth® Audio(P131)
Voice Control(P20)
Use voice commands to control the system while driving. You can operate all key functions of
the navigation and audio systems.
Bluetooth® HandsFreeLink®(P138)
Pair a compatible cell phone to receive incoming and make outgoing calls. You can operate the
phone features without ever taking your hands off the wheel.
InformationProvidedby:
The advanced audio system provides clear, well-defined sound and makes the most of your music.
Enjoy listening to a variety of audio sources, such as:
QRG
Quick Reference Guide - 2013 Fit
Index
Home
3
3 CD/AUX Button (P119)
1 E (Eject) Button
2 FM/AM Button
(P114)
Navigation Screen
(Touch Screen)
Audio
Navigation
Voice Control/
Bluetooth® HandsFreeLink®
6 Disc Slot (P6)
4 AUDIO Button (P6)
5 SEEK/SKIP Button (P114)
7 a (Display Mode)
Button
(P27)
lb DEST Button (P56)
9 PHONE Button (P138)
la MAP/GUIDE Button (P90)
le CANCEL Button
lc INFO Button
(P10)
ld ZOOM IN/OUT Button (P95)
lf Joystick/ENT Button
8 VOL 9 Knob
(P6)
Press ENTER
Selects map location
or list item.
Move up Move LeftMove down Move right
Scrolls map or list.
QRG
InformationProvidedby:
System Controls
Quick Reference Guide - 2013 Fit
Index
Home
4
lg Microphone
(P20)
lh MODE Button (P135)
li VOL (Volume) Button
(P136)
ma h (Pick-Up) Button (P153)
md K (Back) Button (P5)
mc d (Talk) Button (P5)
mb j (Hang-Up) Button (P153)
lj CH (Channel) Button
(P136)
d (Talk) Button
A helpful prompt asks what you
would like to do. Press and release
the d (Talk) button again to bypass
this prompt.
InformationProvidedby:
Voice Control Operation
a Press and release the d (Talk) button.
The icon is displayed and the system beeps when ready for a
command. Press the K (Back) button to cancel.
Available voice commands are highlighted on the screen.
QRG
Quick Reference Guide - 2013 Fit
b Say a voice command.
Voice Command (P183)
The audio system is muted during voice control mode.
Say “Help” to see all supported commands. A voice help
tutorial is also available.
Voice Help (P13)
Carefully read the usage note for the voice control.
Voice Control System (P20)
Index
Home
5
Audio source
Track list
Open icon
Audio source
Displays selected source.
Music
information
Close icon
Sound
preferences
Folder/Track tab
Displays the list.
Repeat and random play
Play mode
Displays or hides the
music information.
Audio control
QRG
InformationProvidedby:
Quick Reference Guide - 2013 Fit
Audio System
You can play music from a wide array of media sources. You can also control the audio system using voice commands.
Basic Operation
a Press the VOL 9 (Volume/Power) button to turn the audio
b Press the AUDIO button and select SOURCE on the screen.
c Select the audio source.
d Rotate the VOL 9 (Volume/Power) knob to adjust
Index
Home
6
system on or off.
Or, press the FM/AM button or CD/AUX button repeatedly to
select the audio source.
the volume.
Audio Control Display
Press the AUDIO button to display the audio system on the
navigation screen.
Map Screen Legend
Map orientation (P97)
GPS signal strength
North up
Heading up
Best reception
Good reception
No icon: Poor/No reception
Current map scale
Current street name/audio control
(Select to switch the display.)
Map menu (P85)
Map scale (P95)
Current vehicle position
(P98)
Feature areas
Streets
Landmark icons (P92)
Park
Hospital
Shopping Mall
Golf Course
Airport
Water Area
Cemetery
University
Freeways
State routes
Verified streets
Unverified streets
One-way streets
Acura dealer
Honda dealer
ATM
School
Parking lot
Parking garage
Grocery store
Hotel/Lodging
Gas station
Hospital
Post office
Restaurant
Freeway exit information
InformationProvidedby:
QRG
Quick Reference Guide - 2013 Fit
Index
Home
7
Calculated route
(P80)
Destination direction
indicator
Direction “as the crow
flies.”
Guidance indicator
Distance to the next
guidance point.
Distance to destination
Distance of the actual
route.
Estimated time to
destination
Waypoint (P101)
Destination icon
(P79)
Calculated route
(unverified roads)
(P82)
Street name of
guidance point
Route guidance list scroll bar
Select R or U to scroll the list of
guidance points.
Route progress bar
Distance to
guidance point
No entry icon
Night mode
Day mode
QRG
InformationProvidedby:
Quick Reference Guide - 2013 Fit
During Route Guidance
During route guidance, route information is displayed on the map/guidance screen.
Press the MAP/GUIDE button to display the guidance screen.
Map Screen
Guidance Screen
Index
Home
8
Day or Night Mode
Press the a (Display mode) button
to manually switch between day and
night mode.
How to Enter Information
Number of Hits
On input search screens, the number of hits in the map database is
displayed. Select List to display a list of possible entries.
NOTE
InformationProvidedby:
You can enter information (e.g., city names, street names, personal names, and business names comprising letters, numbers, and symbols)
when prompted on input screens by two different methods.
QRG
Quick Reference Guide - 2013 Fit
Using Voice Control
When you see d in this manual, voice commands are available for
that feature.
Say the letter, number, or symbol (e.g., say d “A”).
Use spelling assist (e.g., say d “Alpha” to enter the letter “A” or
d “Hyphen” to enter a hyphen).
The system beeps if you say an unavailable (grayed out) letter or
number.
If a voice command is not recognized, a list is displayed with
possible options.
On list screens:
Say the number of the list item (e.g., say d “Five” to select item
5).
Say d “Up” or d “Previous” to scroll up one page.
Say d “Down” or d “Next” to scroll down one page.
Using the Touch Screen
Touch a character or icon on the screen to select it.
Select Delete to remove the last entered character.
Select Shift to display accented and upper/lower case characters.
Select Space to enter a space character.
Select More to display symbols.
You can also use the joystick to enter information.
2 System Controls P. 4
On list screens:
Scrolling through lists or tabs is limited while the vehicle is moving.
Certain touch screen functions are limited or inoperable while the
vehicle is moving. For these functions, use available voice
commands or pull over to proceed.
Index
Home
9
QRG
InformationProvidedby:
Quick Reference Guide - 2013 Fit
Navigation—Home Addresses and Going Home
The “Home” feature automatically routes you to your home address from any location simply by selecting Go Home 1 or 2, or saying d “Go
Home.” You can store two home addresses as Home Address 1 and Home Address 2. (P36)
Index
Storing Your Home Address
a Press the INFO button.
b Select Setup.
c Select Personal Information.
d Select Home Address 1.
e Select Edit Name.
f Enter a name and select OK.
g Select Edit Address.
h Select Address.
i Enter an address.
j Select Edit Phone No.
k Enter a phone number and select OK.
l Select OK.
Going Home
a Press the DEST button.
b Select Go Home 1.
Alternatively, you can say d “Go
Home” from any screen. Your home
address is displayed on the Calculate
Route screen.
c Select Set as Dest.
The following voice commands are
available: say d “Go Home,” d “Go
Home 1,” d “Go Home 2.”
If you have two home addresses stored,
saying d “Go Home” will select Home Address 1.
Home
10
Navigation—Entering a Destination
InformationProvidedby:
Enter your destination using one of several methods, then follow route guidance on the map or guidance screen to your destination. You
can also perform these steps using d voice control.
QRG
Quick Reference Guide - 2013 Fit
a Press the DEST button.
b Select Address.
c Select Street.
d Enter the name of your destination
street and select List if necessary.
e Select your destination street from
the list.
f Enter the street number. Select OK
when finished.
g If there is more than one city with the
specified street, a list of cities is
displayed. Select the desired city from
the list.
h Select Set as Dest.
Route guidance to the destination
begins.
View Routes: Choose one of three
routes.
Route Pref.: Choose MAX or MIN for
the three settings.
Index
Home
11
QRG
InformationProvidedby:
Navigation—Changing Route or Destination
Quick Reference Guide - 2013 Fit
You can alter your route by adding waypoints to visit, adding streets to avoid, or changing your destination during route guidance.
Index
Adding a Waypoint
(“Pit Stop”)
You can add up to four waypoints along
your route. (P101)
a Press the DEST button.
b Select Waypoint.
c Select search method.
When you select Places Around the
Waypoint, select the desired waypoint.
d Select the icon category and location
to add to the destination list when
prompted.
Changing Your
Destination
There are four methods you can use to
specify a new destination during route
guidance.
Say d “Find Nearest…”(P106)
Searches for the nearest place/landmark
on the map screen (e.g., d “Find nearest gas station”).
Say d “Go Home”(P10)
Routes to your home address.
Selecting an icon on the map (P107)
Scroll the map to position the cursor over
a place/landmark icon or a new area on
the map. Press the Enter button twice.
Entering a new destination (P108)
Press the DEST button. Select DEST
Menu1/2 and enter a new destination.
Canceling Your Route
a Press the DEST button.
b Select Cancel Route.
From the map screen:
a Select MAP MENU.
b Select Cancel Route.
Home
12
Voice Help
InformationProvidedby:
This navigation system comes with voice help information, which tells you how to use the voice command functions.
Go to Voice Info for tips when using the voice command functions.
QRG
Quick Reference Guide - 2013 Fit
Getting Started Tutorial
a Press the INFO button.
b Select Voice Info.
c Select Getting started.
You can also view the available
command list for each system. See
Command Help on this page.
d Select Using the talk button.
e Select Read to hear the tutorial read
aloud.
Select Stop to stop the tutorial.
Command Help
For “Command Help” menu items, all voice
commands that are available for that
system are listed.
Select Read to hear the commands in the
list read aloud.
Voice Commands (P183)
Index
Home
13
QRG
InformationProvidedby:
Quick Reference Guide - 2013 Fit
TroubleshootingFor more Information(P159)
Index
Why does the vehicle position icon on the map “lag” a
short distance behind my actual position, especially at
intersections?
This is normal. The navigation system is unaware of the
width of intersections. Large differences in vehicle position
can indicate a temporary loss of the GPS signal.
Why does the “time to destination” display sometimes
increase even though I am getting closer to my
destination?
The “time to destination” is based on the posted road
speed signs and your actual road speed to give you a
better estimate of arrival time.
Why does my clock frequently change the time forward
and backward by one hour?
The clock setting is automatically updated based on your
GPS location. If you normally drive between two time
zones, the clock may keep adjusting the time. You can
turn this feature off.
2
Clock Adjustment P. 47
How do I specify a destination when an entered city or
street could not be found?
Try entering the street first. Some cities are lumped in with
a major metro area. In rural “unverified” areas or new
subdivisions, streets may be missing or only partially
numbered.
How do I turn on the navigation system voice guidance?
1. Press the INFO button. Select Setup. Check that
Volume is not set to Off.
2. Select Other, then Basic Settings. Set Voice
Recognition Tutor to On if you want the system to
provide confirmations and system prompts.
My battery was disconnected or went dead, and the
navigation system is asking for a code. Where do I find it?
Your vehicle comes with a label in the Owner’s Manual kit
that includes the system’s security code and serial number.
You should keep this label in a safe place outside your
vehicle. If you cannot find it, contact your dealer.
Home
14
How to Use This Manual
Searching the Table of Contents
(P1)
Two types of Tables of Contents help
you find your desired information.
First, find the general chapter related to
what you are looking for (e.g., entering
a destination from the Address Book).
Then, go to that chapter to view a more
specific table of contents.
Searching the Index (P194)
Menu items displayed on the
navigation screen (e.g., Address Book)
can be found individually in the Index.
This more detailed table of contents
shows you exactly what information is
listed by section and title.
The Index consists of
main terms and subentries. The sub-entries
help you get to the
desired page depending
on what you are looking
for.
Table of ContentsChapter Contents
Navigation Screen
Index
InformationProvidedby:
This section explains different methods on how you can easily find information in this manual.
More Detailed
Contents
QRG
Quick Reference Guide - 2013 Fit
Go to the
Next Page
Index
Home
15
Menu Tree
The menu tree helps guide you
through the system’s menu options.
To get to your desired function, follow
the menu tree in order of the steps
shown.
NOTE:
All menu options can also be
activated with voice commands.
Press the hard button on the
system control panel.
Press the DEST button.
Select the menu option.
Select Address Book.
After following the menu
tree, step-by-step
instructions explain how to
achieve the desired result.
Sample pages and images in this section may differ from the actual ones.
QRG
InformationProvidedby:
Quick Reference Guide - 2013 Fit
DEST button
Index
Home
16
System Setup
2013 Fit Navigation
InformationProvidedby:
This section describes the start-up procedure and the navigation and
Clear All Speed Dial................................ 54
Index
Home
17
System Setup
Start-up
1 Start-up
If the navigation system loses power at any time,
you may need to press and hold the VOL 9
(Volume/Power) button for more than two
seconds, or you may be prompted for the 5-digit
security code.
2 System Initialization P. 172
You can change the system language at any
time.
2 Language P. 29
“OK” on the Confirmation screen cannot be
selected by using a voice command. If you do not
select OK within 30 seconds, the screen turns
dark and you cannot use voice commands. Press
any navigation or voice control button to
continue.
2 Clock Adjustment P. 47
2 Setting the Clock Type P. 49
2013 Fit Navigation
InformationProvidedby:
QRG
The navigation system starts automatically when you turn the ignition to
TOC
ACCESSORY (I) or ON (II). At start-up, the following Confirmation screen is displayed.
Index
Home
18
1. Select Change Language.
If you do not need to change
the system language, proceed to
step 3.
2. Select the system language.
3. Select OK.
Your current position is
displayed on the map screen.
System Setup
Disabled Option
2013 Fit Navigation
InformationProvidedby:
Start-up
QRG
■ Limitations for Manual Operation
TOC
Certain manual functions are disabled
or inoperable while the vehicle is in
motion. You cannot select a grayedout option until the vehicle is stopped.
Voice commands are still operable
while the vehicle is in motion.
Index
Home
19
System Setup
Voice Control System
1 d (Talk) Button
When you press the d (Talk) button, a helpful
prompt asks what you would like to do. Press
and release the d (Talk) button again to bypass
this prompt and give a command.
1 Command Input
The audio system is muted while using the voice
control system.
2013 Fit Navigation
InformationProvidedby:
QRG
Your vehicle has a voice control system that allows hands-free operation of most of
TOC
the navigation system functions. You can also control the audio system, and make
and receive phone calls using Bluetooth® HandsFreeLink®.
The voice control system uses the d (Talk) and K (Back) buttons on the steering
wheel and a microphone near the map lights on the ceiling.
A “Voice Info” feature provides a tutorial that explains how to use the voice control
system.
2 Voice Help P. 13
Command Input
If the system does not understand a command or you wait too long to give a
command, it responds with “Pardon? No command was heard. Please press the talk
button and say a command.”
When you give a command, the system generally either repeats the command as a
confirmation or asks you for further information. If you do not wish to hear this
feedback, you can turn it off. However, listening to the feedback will help familiarize
you with the way the system expects commands to be phrased.
2 Basic Settings P. 24
If the system cannot perform a command or the command is not appropriate for the
screen you are on, the system beeps.
If the system responds with prompts such as “Please use the touch screen to…” or
Index
Home
“Please use the joystick to…,” the system is asking for input that cannot be
performed using the voice control system.
On character input screens, a list of possible characters is displayed if the system
does not recognize your command.
You can find out which voice commands are available for a particular screen using
the d Help command. The system will display and read the list of available
commands to you.
20
System Setup
Voice Recognition
2013 Fit Navigation
InformationProvidedby:
Voice Control SystemVoice Recognition
QRG
To achieve optimum voice recognition when using either the navigation voice
control system or Bluetooth® HandsFreeLink®:
• Make sure the correct screen is displayed for the voice command that you are
using.
2 Voice Commands P. 184
• Close the windows and moonroof.
• Adjust the dashboard and side vents so air does not blow onto the microphone on
the ceiling.
• Speak clearly in a clear, natural speaking voice without pausing between words.
• Reduce any background noise if possible. The system may misinterpret your
command if more than one person is speaking at the same time.
• Refer to the Voice Info tutorial.
2 Voice Help P. 13
TOC
Index
Home
21
System Setup
Interface Settings
1 Display and Volume Settings
You can set separate daytime and nighttime
settings for Brightness, Contrast, and Black Level. Adjust each setting when the display is in
either daytime or nighttime mode.
You can set the display and volume settings
using voice commands.
2 Main Setup Screen Commands P. 189
Volume
If you set Volume to Off, you will not hear route
guidance or voice command confirmations. If
you then select VOICE on the map menu, you
will hear route guidance at the default volume.
2013 Fit Navigation
InformationProvidedby:
QRG
Display and Volume Settings
H INFO button Setup
TOC
Use the Main Setup screen to adjust the display and volume.
The following items are available:
• Brightness: Adjusts the screen’s brightness.
• Contrast: Adjusts the screen’s contrast.
• Black Level: Adjusts the screen’s black level.
• Volume: Adjusts the navigation system volume level.
Index
Home
22
Select b or n to adjust the desired
item.
System Setup
Guidance Prompts
1 Guidance Prompts
To replay voice guidance, select VOICE on the
map menu.
2 Listening to Voice Guidance P. 84
You can turn voice guidance off if you prefer.
2 Display and Volume Settings P. 22
2013 Fit Navigation
InformationProvidedby:
Interface SettingsGuidance Prompts
QRG
H INFO button Setup
Set the number of guidance prompts before you get to the guidance point.
The following options are available:
Items
MINYes
NORMAL
(factory default)
MAXYesYesYes
About 1/2 mileAbout 1/4 mileJust before
TOC
Select an option.
Distance from Guidance Point
YesYesYes
Index
Home
23
System Setup
2013 Fit Navigation
InformationProvidedby:
Interface SettingsBasic Settings
QRG
Basic Settings
H INFO button Setup Other Basic Settings
TOC
Set the map units to either miles or kilometers, and control the voice feedback from
the navigation system.
The following items are available:
• Keyboard Layout: Sets the type of keyboard screen to either Alphabet (factory
default) or QWERTY.
• Units: Sets the map units to either miles (factory default) or kilometers.
• Voice Recognition Tutor: Turns the voice feedback feature on or off.
On (factory default): Provides voice control system confirmation or prompts.
Off: Disables the feature.
• Display Voice Command Tips: Alerts you when manual control of the system is
disabled to prevent distraction while driving. Only voice commands are available.
On (factory default): Displays a message.
Off: Disables the message, but some options may be grayed out on the screen.
Select an item.
Index
Home
24
System Setup
2013 Fit Navigation
InformationProvidedby:
Interface SettingsColor
QRG
• Verbal Reminder: Turns the verbal reminders on or off.
On (factory default): Provides warning voice messages when:
– Driving with the parking brake on
– Driving without wearing the driver and/or passenger seat belt
Off: Disables the feature.
Color
H INFO button Setup Other Color
Choose the color of the navigation map and system menus.
Select an item.
The following items are available:
• Map: Sets the color of the map screen.
2 Map Color P. 26
• Menu: Sets the color of the menu screens.
2 Menu Color P. 26
TOC
Index
Home
25
System Setup
1 Map Color
For Day mode
Set to White (factory default is Beige) to obtain
the best daytime display contrast.
For Night mode
Set to Black (factory default) to obtain the best
nighttime display contrast.
1 Menu Color
For Day mode
Set to Black (factory default is Blue) to obtain
the best daytime display contrast.
For Night mode
Set to Black (factory default is Blue) to obtain
the best nighttime display contrast.
2013 Fit Navigation
InformationProvidedby:
Interface SettingsColor
QRG
■ Map Color
TOC
H INFO button Setup Other Color Map
Set separate map colors for Day and Night modes.
■ Menu Color
H INFO button
Set separate menu colors for Day and Night modes.
Index
Home
26
Setup Other Color Menu
Select a color for the map screen.
Select a color for the menu screens.
System Setup
1 Switching Display Mode Manually
A visual guide helps you see the difference
between Day and Night modes.
2 Day or Night Mode P. 8
Recommended Settings
• Select mid-range for the dash illumination.
• Select White for the map Day display and
Black for the map Night display.
2013 Fit Navigation
InformationProvidedby:
Interface SettingsColor
QRG
■ Switching Display Mode Manually
Set the screen brightness separately for Day and Night modes. Press the
(Display mode) button to cycle through the display modes (Day to Night to Off).
a
1. Press the a button.
The Brightness bar is displayed
for a few seconds.
2. Press the a button again.
Repeat the procedure to switch
the display modes.
Select b or n to adjust the
brightness.
Continued
TOC
Index
Home
27
System Setup
QRG
2013 Fit Navigation
InformationProvidedby:
Interface SettingsColor
TOC
Index
Illumination
control
PriorityOperation
a button1Selects Day, Night, or Off display mode. This button has
the highest priority and overrides all other display control
adjustments listed below.
Sunlight sensor
(see your
Owner’s Manual
for location)
2If the sunlight sensor detects daylight and the headlights
are turned on, the system automatically overrides the
Night display and displays the Day display mode.
Remember: If desired, use the a button to override
this automatic choice.
Dash illumination
adjustment
buttons (see your
Owner’s Manual
for location)
3When the headlights are turned on, and you wish to have
the Day display mode, adjust the illumination to full
brightness (beeps).
Remember: Adjust the dash brightness back to mid-range
to allow auto switching by sensing the headlights are on or
off.
Headlights
(Auto/On/Off)
4When turned on, the display changes to Night display
mode. The previous three controls listed above can
“cancel” this function.
Remember: Use the a button, or adjust the dash
illumination to full brightness, to set the display to your
desired choice.
Screen color
choice
N/AThe user can select the color of the screen that will be
displayed for the Day and Night display modes described
above.
Remember: For best contrast, ensure that the map color is
white for Day and black for Night.
Home
28
System Setup
Language
1 Language
Voice confirmation of cities and streets only
occurs when English is the system language.
When Français or Español is selected, some
messages continue to be displayed in English.
2013 Fit Navigation
InformationProvidedby:
Interface SettingsLanguage
QRG
H INFO button Setup Other Language
Set the system language used on all screens. You can choose from three languages:
English, Français (French), Español (Spanish).
Select the system language.
TOC
Index
Home
29
Loading...
+ 168 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.