Hobart H600 User Manual

H600 MIXER

H600 & L800 MIXERS

MODELS

H600 ML - 104241, 104242, 104383, 104384

L800 ML - 104244, 104245, 104425, 104429

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

FORM 18812 Rev. B (12-99)

Model H600 Mixer Model L800 Mixer

– 2 –

2345678901234567890123456789012123456789

The H600 model mixer is a heavy duty 60 quart mixer which features a 2 horsepower motor, a timer, and a #12 attachment hub as standard equipment. With the use of bowl adapters and special agitators, 30 or 40 quart bowls may be used on the H600.

The L800 model mixer is a medium duty 80 quart mixer designed primarily for use in general kitchen applications. This mixer features a timer and #12 attachment hub as standard equipment and is powered by a 2 horsepower motor. With the use of bowl adapters and special agitators, 30, 40, or 60

23456789012345678901234567890121234567890123456789012345678901212345678901

Installation, Operation, and Care of

H600 and L800 MIXERS

SAVE THESE INSTRUCTIONS

GENERAL

quart bowls may be used on the L800.

Bowl Guard is standard equipment on all H600 and L800 models.

Programmable Timer Controller is optional on H600 and L800 models.

These mixers can be ordered with deluxe finish, which includes a chrome plated transmission case, base, bowl support, and pedestal.

A variety of attachments and accessories are available for all mixers. These are described in a separate

Use and Applications Handbook

which is furnished with each mixer.

– 3 –

INSTALLATION

UNPACKING

Immediately after unpacking the mixer, check for possible shipping damage. If this machine is found to be damaged after unpacking, save the packaging material and contact the carrier within 15 days of delivery.

Prior to installation, test the electrical service to assure that it agrees with the specifications on the machine data plate.

LOCATION

Place the mixer in its operating location. There should be adequate space around the mixer for the user to operate the controls and install and remove bowls. The area above the mixer should allow the top cover to be removed for routine maintenance and servicing.

Holes are provided in the base for permanent bolting to the floor, although this is not necessary in normal installations. Four plastic plugs are supplied with the mixer to plug these holes if they are not used.

Once located, the mixer must be leveled.

Remove the top cover screws and the top cover.

Place a level on the machined surface of the transmission case (Fig. 1) and slide shims under the legs (base) of the mixer as required to level it front-to-back and side-to-side.

Do not replace the top cover until installation is completed.

Fig. 1

Check Lubrication Before Use

This mixer is shipped with oil in the transmission and planetary. Check oil levels before starting mixer. Refer to

LUBRICATION

, pages 13 – 14, for applicable lubrication procedures.

– 4 –

ELECTRICAL CONNECTIONS

WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE

APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL ELECTRICAL CODES.

WARNING: DISCONNECT ELECTRICAL POWER SUPPLY AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT.

ELECTRICAL DATA

Model Volts / Hz / Ph

H600 115 / 60 / 1 19.0 25 25 10 30 30 10

H600 200 / 60 / 1 10.9 15 15 14 20 20 12

H600 230 / 60 / 1 9.5 15 15 14 15 15 14

H600 200 / 60 / 3 5.8 15 10 14 15 10 14

H600 230 / 60 / 3 5.0 15 6 14 15 10 14

H600 460 / 60 / 3 2.5 15 3 14 15 6 14

H600 ‡ 200 / 60 / 1 14.3 20 20 12 20 20 12

H600 ‡ 230 / 60 / 1 12.9 20 20 12 20 20 12

H600 ‡ 200 / 60 / 3 9.2 15 15 14 20 20 12

H600 ‡ 230 / 60 / 3 8.4 15 10 14 20 20 12

L800 200 / 60 / 1 12.7 20 20 12 20 20 12

L800 230 / 60 / 1 11.0 15 15 14 20 20 12

L800 200 / 60 / 3 6.5 15 10 14 15 15 14

L800 230 / 60 / 3 5.6 15 6 14 15 10 14

L800 460 / 60 / 3 2.8 15 3 14 15 6 14

L800 ‡ 200 / 60 / 1 16.1 25 25 10 30 30 10

L800 ‡ 230 / 60 / 1 14.4 20 20 12 25 25 10

L800 ‡ 200 / 60 / 3 9.9 15 15 14 20 20 12

L800 ‡ 230 / 60 / 3 9.0 15 15 14 20 20 12

‡ Power Bowl Lift

Circuit Size (Minimum) & Fuse / Circuit Breaker Size (Maximum) compiled in accordance with the National Electrical Code (ANSI/NFPA 70), 1993 Edition.

Rated

Amps

Circuit Size

(Amps)

* Dual Element

Fuse Size *

(Amps)

Time-Delay Fuse

60°C Copper

Wire Size

Circuit Size

(Amps)

** Inverse Time

Circuit Breaker **

(Amps)

Circuit Breaker

60°C Copper

Wire Size

A hole for

⁄4" trade size conduit is located at the top of the pedestal. Make electrical connections per

the wiring diagram located on the inside of the Top Cover.

Check Rotation (Three-Phase Machines Only)

Three-phase machines must be connected so the planetary rotates in the direction of the arrow on the Drip Cup. To check rotation:

Set the gear shift lever on 1.

Apply power to the mixer, set the Electro-Mechanical Timer on HOLD; or, if equipped with a Programmable Timer Controller, set it on [ -- : -- ]. With the Bowl Support all the way up, momentarily run the machine by pushing the START and then STOP buttons.

If rotation is incorrect, DISCONNECT ELECTRICAL POWER SUPPLY and interchange any two of the incoming power supply leads.

– 5 –

+ 11 hidden pages