Hobart CU60 Owner’s Manual

CU SERIES

COMPACT UNDERCOUNTER FOOD STORAGE CABINETS

MODEL

CU27 ML-111169 CUF27 ML-111170 CUS27 ML-111171

CU48 ML-111175 ML-111185 CUF48 ML-111176 ML-111186 CUS48 ML-111177 ML-111187

CU60 ML-111178 ML-111188 CUF60 ML-111179 ML-111189 CUS60 ML-111180 ML-111190

701 S. RIDGE AVENUE

TROY, OHIO 45374-0001

937 332-3000

www.hobartcorp.com

FORM 34057 Rev. C (Jan. 2002)

SANDWICH PREP TABLES REFRIGERATOR / FROZEN FOOD

STORAGE CABINETS

MODEL CUS27

MODEL CUS48

MODELS CU27 or CUF27

MODELS CU48 or CUF48

MODEL CUS60

MODELS CU60 or CUF60

– 2 –

Installation, Operation and Care of

CU SERIES COMPACT UNDERCOUNTER

FOOD STORAGE CABINETS

SAVE THESE INSTRUCTIONS

GENERAL

CU Series are 27", 48" or 60" wide refrigerator, frozen food or sandwich preparation type food storage cabinets. The cabinets measure 29 are insulated with urethane foam. CU Series condensing units are front breathing, ventilate from the bottom at the front of the cabinet and cannot be enclosed underneath. CU Series refrigerator and sandwich prep compressors utilize R134A refrigerant. CUF27 frozen food cabinet uses R134A; CUF48 and CUF60 frozen food cabinets use R404A.

Cabinet interior is DuraFinish exterior back and bottom are galvanized steel.

Cabinet doors have spring-loaded hinges that stay open at 105° and self-close below 90°. Doors can be reverse-hinged at the installation site. Vinyl door gaskets with magnetic seal are easy to clean.

CU Series wire shelves are supported by adjustable clips and pilasters.

CU Series cabinets are self-contained and are equipped with cord and plug, standard.

Options include the following: 6" Legs, a variety of Casters, a 6" high Front Ventilated Utility Base (27" wide only), Field-Installed Stainless Steel Worktop with Backsplash, Field-Installed Stainless Steel Worktop with Backsplash and Removable Polyethylene Worktop, Stack Kit (CU27 or CUF27 only), additional Shelves, Overshelves and Stainless Steel Clad Back. Some options are not available on all models.

/2" high, exclusive of legs, casters or cabinet base. Cabinet walls

aluminum. Exterior is stainless steel, on front, sides and top. The

INSTALLATION

Prior to installation, test the electrical service to assure that it agrees with the specifications on the machine data plate located on the upper left wall inside the cabinet.

UNPACKING

Immediately after unpacking, check for possible shipping damage. If the refrigerator is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery.

Do not lay the refrigerator on its back, front or sides.

LOCATION

Condenser performance is dependent on adequate ventilation for cooling purposes. Adequate clearance MUST be provided for the ventilator locations underneath. There are no clearance requirements for sides, rear or top. If installing over a 27" wide utility base, provide adequate clearance at rear of unit to clean the condenser coil (refer to pages 6 and 15).

NOTE: Do not install the cabinet without legs, casters or front-ventilated utility base.

– 3 –

LEGS OR CASTERS

WARNING: THE CABINET MUST BE BLOCKED AND STABLE BEFORE INSTALLING LEGS OR

CASTERS.

Raise up and block the cabinet a minimum of 7" from the floor and thread the legs into the Threaded Holes on the bottom of the cabinet (Fig. 1). Thread optional casters into the Threaded Holes on the bottom of the cabinet in the same way (Fig. 2). Casters with brake should be installed at the front. Tighten securely using octagon-shaped head of Bolt underneath — not round flange on top.

THREADED HOLE

BOLT

RAISE

Fig. 1 Fig. 2

LOWER

PL-56125

PL-53353

LEVELING

Level the cabinet using a spirit level or pan of water in the bottom of the cabinet. On units with legs, turn the adjustable feet in or out to level the cabinet side-to-side and front-to-back. Units with casters should be placed on level floors.

SHELVES (Fig. 3)

PILASTER KEYHOLE SUPPORT

Shelves and Shelf Clips are packed with the unit. For each Shelf, insert four Shelf Clips into the Pilaster Slots at the same height. The Shelf Clips

PILASTER KEYHOLE

PILASTER

SHELF CLIP

have a small projection on top which holds the Shelf in position and prevents it from slipping forwards. After installing the Shelf Clips on the Pilasters, place the Shelves on the Shelf Clips.

SLOT

– 4 –

SHELF

PL-53057

Fig. 3

SANDWICH PREP TOP ASSEMBLY (Figs. 4, 5)

On sandwich prep tables (Fig. 5), the top shelf, cutting board and cover may require assembly.

1. Place the Shelf on top of the rear of the unit. Secure by screwing four threaded Pins through base of Shelf and top of unit (Fig. 4).

2. Install Cutting Board Support. Secure with two threaded Pins and two Bolts per Flange (Fig. 4) (wider units may be equipped with an additional third Pin in the center).

3. Assemble Cutting Board to Cutting Board Support (Pins holding Cutting Board Support

CUTTING BOARD

fit through holes in Cutting Board when properly aligned — Fig. 4).

4. To install Cover, flex Cover so side Pins fit in holes at lower front corners of Shelf (Fig. 4). Cover pivots up to open.

SHELF

PINS (4)

PINS (2)

Fig. 4

CUTTING BOARD SUPPORT

FLANGE (1 OR 2)

BOLTS (2 PER FLANGE)

COVER

– 5 –

Fig. 5

+ 11 hidden pages