Page 1
Item # _____________________________________
Quantity ___________________________________
C.S.I. Section 11400
CLe STEAM
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
STANDARD FEATURES
■ Stainless steel 33" long chamber
■ Positive forced circulation of high velocity
heated air
■ Fits CLe models
■ High velocity industrial type blower-dryer is
quiet, giving truly high performance at a low
sound level
■ 2 H.P. blower
■ 55 lbs. per hour steam consumption
DIRECTION OF OPERATION
❑ Right to Left
❑ Left to Right
BLOWER-DRYER ACCESSORY
MODEL
❑ CLe Steam Blower-Dryer
Specications, Details and Dimensions on Inside and Back.
For use with
CLe Series Dishwashers
CLe STEAM BLOWER-DRYER ACCESSORY
VOLTAGE
❑ 480/60/3
❑ 208-240/60/3
F-40265 – CLe Steam Blower-Dryer Accessory Page 1 of 4
Page 2
CLe STEAM
BLOWER-DRYER ACCESSORY L-R
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Page 2 of 4 F-40265 – CLe Steam Blower-Dryer Accessory
Page 3
CLe STEAM
S
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
BLOWER-DRYER ACCESSORY R-L
F-40265 – CLe Steam Blower-Dryer Accessory Page 3 of 4
Page 4
CLe STEAM
BLOWER-DRYER ACCESSORY
DESIGN: To promote rapid drying of tableware and
trays by forced circulation of high velocity heated air
through the blower dryer.
Heavy-duty direct drive industrial fan blows room
air through a steam coil and large area ducting.
Heated air directed vertically downward to drying
area through rectangular orice covering full width of
chamber. Bafes below conveyor redirect air upward
within drying area and minimize heating of discharge
table or hot air contact with clean-dish operator at
end of machine.
Any object which will pass through the machine will
be handled at the dryer area without necessity of
readjusting blower plenum upward or downward.
CONSTRUCTION: Chamber construction is stainless
steel, welded and bolted. Vent is 4" x 16" inside
dimension and contains a locking type control
damper.
Stainless steel wrap-around encloses entire external component assembly consisting of steam coils,
motor and blower. Blower dryer is approximately
173⁄8" above height of machine.
Tank portion is constructed of stainless steel with
legs and lower cross-members of 15⁄8" stainless steel
tubing and stainless steel adjustable feet.
701 S Ridge Avenue, Troy, OH 45374
1-888-4HOBART • www.hobartcorp.com
Conveyor is Hobart “Dual Drive” with stainless steel
pawls, designed to connect to CLe warewasher.
STEAM COILS: One double rowed heavy-duty high
efciency aluminum nned copper tube type heat
exchanger. The steam blower comes with one of each
of the following connections: a 1 inch female I.P.S.
steam, and a 3⁄4 inch I.P.S. steam condensate connections. Steam requirements are 55 lbs. at 20 psi.
Maximum steam pressure 25 psi.
BLOWER: Industrial fan-type with direct drive wheel.
Housing of welded construction.
2 H.P. Blower direct drive motor. Exhaust requirement
is 200 to 400 CFM.
MOTOR: Splashproof enclosure, ventilated design.
Furnished only in three-phase electrical specications
of the basic CLe Model in 208-240/60 and 480/60.
The controller circuit operates on 115 volts supplied
by the transformer on the dishwasher.
MOTOR CONTROL: Ambient temperature
compensated automatic resetting solid state overload protection, pre-wired. Operation controlled by
dishwasher motor switch, i.e. blower functions only
during machine operation.
As continued product improvement is a policy of Hobart, specications are subject to change without notice.
Page 4 of 4 F-40265 – CLe Steam Blower-Dryer Accessory
F-40265 (REV. 09/09) LITHO IN U.S.A. (H-01)
Loading...