Hitachi C28WF532N User Manual

Users Guide

C28WF532N

SCREEN

Dear HITACHI customer

Congratulations on your purchase of the very latest state of the art

technology from Hitachi. At Hitachi we pride ourselves on producing high

quality televisions with outstanding picture and audio capabilities. Together

with Hitachi’s reputation for superior reliability, you should enjoy many years

of trouble free operation from your TV.

Software Notice

It is prohibited for the end user of this product to copy, reverse engineer

or reverse compile the software included therein, save to the extent

permitted by law.

Caution

To prevent scratching or damaging the tube face, do not knock or rub

the surface with sharp or hard objects. Clean the screen with a soft cloth

moistened with warm water and dry with a soft cloth. A mild soap may be

used if the screen is extremely dirty. Do not use harsh or abrasive cleaners!

Important

Please read this Users Guide thoroughly, especially the Safety

Notes on Page 4. Mis-use may cause damage to your television,

which could shorten its lifespan, or cause injury to yourself. Should

you encounter any difficulty in the set-up or operation of your

television, firstly refer to the Trouble Shooting Guide at the rear of

this manual.

In the unlikely event of a problem occurring with your TV, switch off at the mains

socket, pull out the plug, and contact your dealer immediately.

Under no circumstances remove the rear cover of your TV.

Never guess or take any chances with electrical equipment

of any kind - it is better to be safe than sorry!

Virtual Dolby Surround

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”

and the double-D symbol are trademarks of Dolby Laboratories.

contents

safety aspects

television safety ................................................................................4

battery safety and installation............................................................5

TV controls overview

front control panel details ..................................................................6

rear socket and scart details. ............................................................7

set-up

aerial, decoder, VCR and DVD installation ........................................8

handset controls

programme tuning ............................................................................9

television/VCR operation....................................................................10

Teletext functions ..............................................................................11

tuning in

TV set up and automatic tuning procedure ......................................12

manual tuning procedure ..................................................................14

programme sort ................................................................................16

programme name change and download ........................................17

Viewlink ..............................................................................................18

customer I.D. ....................................................................................20

password change ..............................................................................21

programme, sound and vision adjustment

picture controls ..................................................................................22

Dolby Virtual and NICAM sound controls ..........................................23

audio and equaliser controls ............................................................24

television features

sleep timer and On Screen Display ..................................................26

wide screen viewing ..........................................................................27

Teletext operation ............................................................................29

other equipment

other equipment connection ............................................................30

signal source entry ............................................................................31

audio visual setup ..............................................................................33

other features

language and installation ..................................................................34

programme download and demo mode ..........................................35

information

trouble shooting guide ......................................................................36

guarantee ..........................................................................................37

HITACHI environmental notice ..........................................................38

technical data ....................................................................................39

television safety

safety aspects

This television has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured.

DO NOT cut off the fitted mains plug as it may contain a special radio interference filter, the

removal of which could lead to impaired performance. If you wish to extend the lead, obtain an appropriate extension lead or consult your dealer.

DO NOT continue to operate the equipment if you are in any doubt about it working normally or if it is damaged in any way - switch off, withdraw the mains plug and consult your dealer.

IF you intend placing this TV into a cabinet or a wall alcove, please ensure there is at least a 100mm (10cm) gap to the sides, rear and top of the TV. This is to allow for adequate ventilation during your TV's operation.

DO NOT leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or handicapped people.

DO NOT obstruct the ventilation of the equipment, for example with curtains or soft furnishings. Overheating will cause damage and shorten the lifespan of your equipment.

DO NOT use makeshift stands and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved stand or legs with the fixings provided according to the instructions.

DO NOT allow electrical equipment to be exposed to rain or moisture.

DO be careful with any glass panels or doors on equipment.

DO consult your dealer if you are in any doubt about installation, operation or safety of your equipment.

DO place your TV on a flat surface, or if supplied, the stand accessory.

DO NOT remove any fixed cover as this may expose dangerous voltages.

DO ensure that all connections, (including the mains plug, extension leads and inter-connections

between the pieces of equipment), are properly made and in accordance with the manufacturers instructions. Switch off and withdraw the mains plug before making or changing connections.

DO NOT listen to headphones at high volume, as such use can permanently damage your hearing.

DO read the operating instructions before you attempt to use the equipment.

DO NOT use equipment such as personal stereos or radios so that you are distracted from the

requirements of traffic safety. It is illegal to watch television whilst driving.

DO NOT place hot objects such as candles or nightlights on, or close to, equipment. High temperatures can melt plastic and lead to fires.

DO observe the manufacturers instructions when connecting extension leads to your TV. The fuse should be a 5 Amp fuse with the safety symbols and displayed. If you are in any doubt about the extension installation, please consult a competent electrician.

DO NOT place objects filled with liquids, e.g. a vase, on, or close to the equipment, to avoid spillages into the inside of the apparatus.

SHOULD you require to replace the fuse in the moulded plug with a new fuse, then please replace with one of the same value, type and approval as the original. Ensure the fuse cover is returned to its original position.

TO prevent scratching or damaging the tube face, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth moistened with warm water and dry with a soft cloth. A mild soap may be used if the screen is extremely dirty. Do not use harsh or abrasive cleaners!

NEVER let anyone, especially children, push anything into holes, slots, or any other opening in the case - this could result in a fatal electrical shock. Under NO circumstances remove the rear cover of your TV!

NEVER guess or take chances with electrical equipment of any kind - it is better to be safe than sorry!

always

battery safety and installation

safety aspects

1. When inserting the batteries make sure the polarities are correct, that is, ‘+’ to ‘+’, ‘-’ to ‘-’.

2. Replace the batteries with the equivalent ‘AA’ type.

3. Discard old batteries safely, following the battery safety guidelines.

battery installation

Remove cover of handset by lifting up the cover at the recess.

Insert batteries into handset as shown and replace cover.

Take care to fit your batteries

correctly, observing the plus

‘+’ and minus ‘-’ marks on the battery and appliance.

Incorrect fitting can cause

leakage, or in extreme

cases, fire or explosion.

always

Replace the whole set of batteries at one time, taking care not to mix old and new

batteries of different types,

since this can result in leakage, or in extreme

cases, fire or explosion.

always

Store unused batteries in

their packaging and away

from metal objects which may cause a short circuit resulting in leakage, or in

extreme cases, fire or

explosion.

always

Remove dead batteries from

equipment, and all batteries

from equipment that is to be

left for long periods of time without any use. Otherwise the batteries may leak and

cause damage.

never!

Never dispose of batteries in

fire as this can cause an

explosion.

Respect the environment -

always dispose of batteries

in an environmentally friendly

manner.

never!

Never attempt to recharge

ordinary batteries, either in a

charger or by applying heat to

them. They may leak, cause

fire or even explode.

Rechargeable NiCAD batteries

and chargers can be

purchased from any good

High Street electrical retailer.

CHARGE

+-+-+-+

This will be lit when

your TV is on and when in

standby mode, and flash

when a function

from your remote control

is being sent to the TV.

This is for reading

commands sent

from your remote control

handset.

Use this to switch your TV on and

off. (When switched off using this button

your TV consumes no power - unlike

when in standby mode).

To use the controls push the door in and release.

These sockets are for

use with external

equipment.

This socket is for use

with external equipment.

Used with

headphones (3.5mm stereo

jack plug required).

Used to access your

on screen MAIN MENU for

TV features adjustment.

Used to change the TV

channel up ‘+’ or down ‘-’ (or

cursor up and down when using the

On Screen Display menus).

Used to increase ‘+’, or decrease ‘-’ your TV's sound (or cursor right and left when in On

Screen Display menus).

on/off button

TV mode light

infra-red lens

television controls door panel

headphone socket

S-VHS sockets

audio/video sockets

volume buttons

program buttons

menu button

front control panel details

TV controls overview

AV4

Use this socket to connect

ordinary VHS, S-VHS or Hi8

equipment to your TV.

(Connect VCR to AV1 for

Viewlink).

AV4

AUDIO

LINE OUT

AV1

AV2

Use this to connect

digital video broadcasting

equipment, home

computers and home

entertainment systems to

your TV.

This should be

permanently connected to

an RF source - i.e your

aerial antenna.

AV2 scart input

AV1 scart input

RF aerial socket

Before

connecting external

equipment, please

consult

audio visual

setup section.

rear socket and scart details

TV controls overview

important note on installation

If you intend placing this TV into a cabinet or wall alcove, please ensure there is at least a 100mm (10cm) gap to the sides, rear and top of the television. This

is to allow for adequate ventilation.

Do not allow soft furnishings, such as curtains to be draped over the TV whilst

in operation.

Never place the TV onto a carpet during normal operation - this could obstruct

ventilation slots on the base of the TV.

Always place the TV on a flat surface, or if supplied, the stand accessory.

Failure to observe the above guidelines could result in serious

overheating of your TV, or even, in extreme cases, fire.

Use this to connect

digital video broadcasting

equipment, home computers, home

entertainment systems and

DVD players etc. to your

TV.

AV4 scart input

Use this to connect to

external amplifier or Hi-Fi

system.

audio output (RCA)

AV1

AV2

AUDIO

LINE OUT

TV Setup

AUX

VCR TV

OUT

AV4

AV1

AV2

AV4

AV1

AV2

OUT

AV1/TV

AV2/

DECODER

OUT

aerial, decoder, VCR and DVD installation

set-up

IMPORTANT

NOTE :

When you

connect your VCR

to your television,

the Audio Visual

option has to be

set correctly to

ensure best picture

quality - see audio

visual setup section.

Connect aerial connection lead to

the STB/Decoder ‘in’ socket marked

DVD PLAYER/COMPUTER/GAMES

SCART LEADS * (optional)

RF LEADS (1 SUPPLIED)

VHS video equipment

should be connected to the

AV1 scart socket located at the

rear of your TV. A dedicated

programme number may be

assigned to AV1, allowing you

easier access to external

equipment viewing. How to assign an

AV signal to dedicated programme

numbers is explained in signal

source entry section.

* Scart leads should be

fitted between your TV and

other equipment to enhance

your picture and sound quality.

Scart leads are essential if you

have a stereo TV and VCR and

wish to obtain stereo sound from your

equipment. These leads can be

purchased from your Hitachi

dealer or any good High Street

electrical retailer.

Connect STB/Decoder ‘out’ to VCR

‘in’ socket marked .

Connect VCR ‘out’ to TV ‘in’ socket

marked .

VCR

STB/DECODER

AERIAL

Press this

button to leave the

menu you are on and

return to normal TV

operation.

This button is

used to enter the

main menu. This is

where your TV’s

features options are

displayed.

Use this button

to move the menu

selection box right.

Use this button to

move the menu

selection box left.

Use this button

to move the menu

selection box down.

cursor down

cursor up

television

exit

cursor right

The handset controls shown below are

used when programming your TV and to

adjust the sound and picture features.

cursor left

Use this button to

move the menu

selection box up.

This button is used

to confirm a

highlighted

selection.

programme tuning

handset controls

This button is

used to return to the

previous on screen

menu you were

viewing, or to cancel a

selection.

number/letter buttons

These number buttons can also be used to enter letters, which

are required for some features e.g. programme name change etc.

To enter letters: Press the number key twice for the first

corresponding letter (written above the key), three times for the

second etc.

Example: Press number key 2, twice for ‘A’, three times for ‘B’ and

four times for ‘C’.

This allows you

to directly input

known broadcasting

CH or

frequency numbers.

frequency

Use this button

to display the current

time on screen.

time

Used to switch

your TV in and out of

standby mode.

standby

Used to

increase ‘+’ or

decrease ‘-’ your

TV’s volume.

volume

controls

Used to select

a signal source for

external equipment.

AV setup

This button

allows you to switch

the TV’s sound on and

off.

sound mute

Press this button

to view the current

TV status.

info

The handset controls

shown here are used when your

TV is in normal operation.

Press both

buttons

simultaneously to

record what is being

viewed (only available

if VCR is Viewlink

compatible -see

Viewlink section).

VCR/record

Used to change

channels either up

‘+’ or down ‘-’.

programme controls

television/VCR operation

handset controls

Press both

buttons

simultaneously to stop

recording (only

available if VCR is

Viewlink compatible -

see Viewlink section).

VCR/stop

This button allows you to switch between the various

wide screen features

of your TV

(see wide screen

viewing section).

16:9 button

This allows you

to directly input

known broadcasting

CH or

frequency numbers.

frequency

VCR Operation

Your handset incorporates controls for operation of HITACHI Video Cassette Recorders. These

controls are PLAY, STOP, REWIND, FAST FORWARD and PAUSE.

To PLAY : Press the VCR and Play buttons on your handset simultaneously. To STOP : Press the VCR and Stop buttons on your handset simultaneously. To REWIND : Press the VCR and Rewind buttons on your handset simultaneously. To FAST FORWARD : Press the VCR and Fast Forward buttons on your handset simultaneously. To PAUSE : Press the VCR and Pause buttons on your handset simultaneously.

Teletext functions

handset controls

(red, green,

yellow, blue)

On certain pages in

teletext, these will

have coded instructions

i.e. a shortcut to a

teletext page or title.

colours

Restores TV

picture whilst the TV

is l

ooking for the

entered

Teletext page.

Use this to

access a subtitle

service directly rather

than through a teletext

service (subject to

subtitle service

broadcasting).

Use this button

to expand the size of

the teletext page on

view.

Press this

button to return to

normal TV operations

when in the teletext

mode.

Used in Teletext

mode to show hidden

information eg. quiz

pages answers.

reveal

television

expand

subtitles

Pressing this

button will take you to

the index.

index

In teletext mode

- views the previous page.

In TV mode - returns

from your current

viewing channel to the

previous one.

swap

Use this to

‘freeze’ the teletext

page on display to

prevent the page

changing (press again

to continue).

hold

Press this

button to use the

Teletext services.

teletext

update

The handset

controls shown here

are used when you are

operating Teletext.

See ‘Teletext operation’

section for details of

Teletext services

TV set-up and automatic tuning procedure

tuning in

important note on VCR and satellite

Do not switch your TV on until all external equipment is connected. If you have a Video

Cassette Recorder or a Satellite receiver connected to this TV please ensure that they

are switched on before automatic tuning begins. In the case of a VCR, if it is not Viewlink

compatible, insert a pre-recorded tape and begin playback of your equipment. If it is

Viewlink compatible leave VCR in Standby. (See Viewlink section of this manual for

details). With a Satellite receiver select Sky News. These measures ensure that all your

external equipment is tuned in during the autotune procedure.

The first screen

viewed will ask you to

choose the language of

your TV’s display. Use the

LEFT/RIGHT cursor buttons

to choose your language.

To make your

programme tuning

easier, HITACHI have

installed an automatic

tuning procedure to

find the programmes.

Switch your TV on.

connecting to the mains socket

Important - If you have not already done so, please read the television safety section before connecting your television and external equipment.

insert plug...

...and switch on

important note - on-screen help

When using the

menus of your Television,

extra on screen help will be

displayed in this window.

+ 28 hidden pages