Hitachi BZ-1M User Manual

Projector

BZ-1

(Type nos. BZ-1, BZ-1M)

User's Manual (detailed)
Operating Guide

Thank you for purchasing this projector.

WARNING

product. Be sure to read “Safety Guide” first. After reading them, store them in a
safe place for future reference.

About this manual

Various symbols are used in this manual. The meanings of these symbols are
described below.

WARNING

CAUTION

NOTICE This entry notices of fear of causing trouble.

NOTE

• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.

• The manufacturer assumes no responsibility for any errors that may appear in
this manual.

• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.

Trademark acknowledgment

• Mac® is a registered trademark of Apple Inc.

• Windows
Corporation in the U.S. and/or other countries.

• VESA and DDC are trademarks of the Video Electronics Standard Association.

•

HDMI, the HDMI logo, and High-Definition Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United States and other countries.

• Trademark PJLink is a trademark applied for trademark rights in
Japan, the United States of America and other countries and areas.

• Blu-ray Disc

•

StarBoard® is a registered trademark of Hitachi Solutions, Ltd. in Japan and other countries.

All other trademarks are the properties of their respective owners.

• The information in this manual is subject to change without notice.

®

►Before using this product, please read all manuals for this

This symbol indicates information that, if ignored, could possibly
result in personal injury or even death due to incorrect handling.

This symbol indicates information that, if ignored, could possibly
result in personal injury or physical damage due to incorrect
handling.

Please refer to the pages written following this symbol.



, DirectX®, DirectDraw® and Direct3D® are registered trademarks of Microsoft

TM

and Blu-rayTM are trademarks of Blu-ray Disc Association.

1

Read this Safety Guide first.

Projector

User's Manual - Safety Guide

Thank you for purchasing this projector.

WARNING •

correct usage through understanding. After reading, store them in a safe place for
future reference. Incorrect handling of this product could possibly result in personal injury
or physical damage. The manufacturer assumes no responsibility for any damage caused
by mishandling that is beyond normal usage defined in these manuals of this projector.

Before using, read these user's manuals of this projector to ensure

NOTE

• The manufacturer assumes no responsibility for any errors that may appear in
this manual.

• The reproduction, transmission or use of this document or contents is not
permitted without express written authority.

• The information in this manual is subject to change without notice.

About The Symbols

Various symbols are used in this manual, the user’s manual and on the product
itself to ensure correct usage, to prevent danger to the user and others, and to
prevent property damage. The meanings of these symbols are described below.
It is important that you read these descriptions thoroughly and fully understand
the contents.

This symbol indicates information that, if ignored, could

WARNING

CAUTION

Typical Symbols

This symbol indicates an additional warning (including cautions). An
illustration is provided to clarify the contents.

possibly result in personal injury or even death due to
incorrect handling.

This symbol indicates information that, if ignored, could
result possibly in personal injury or physical damage
due to incorrect handling.

This symbol indicates a prohibited action. The contents will be clearly
indicated in an illustration or nearby (the symbol to the left indicates that
disassembly is prohibited).

This symbol indicates a compulsory action. The contents will be clearly
indicated in an illustration or nearby (the symbol to the left indicates that
the power plug should be disconnected from the power outlet).

1

Safety Precautions

WARNING

Never use the projector if a problem should occur.

Abnormal operations such as smoke, strange odor, no image, no sound,
excessive sound, damaged casing or elements or cables, penetration of
liquids or foreign matter, etc. can cause a fire or electrical shock.
In such case, immediately turn off the power switch and then disconnect the
power plug from the power outlet. After making sure that the smoke or odor
has stopped, contact your dealer. Never attempt to make repairs yourself
because this could be dangerous.

• The power outlet should be close to the projector and easily accessible.

Use special caution for children and pets.

Incorrect handling could result in fire, electrical shock, injury, burn or vision
problem.
Use special caution in households where children and pets are present.

Do not insert liquids or foreign object.

Penetration of liquids or foreign objects could result in fire or electrical shock.
Use special caution in households where children are present.
If liquids or foreign object should enter the projector, immediately turn off the
power switch, disconnect the power plug from the power outlet and contact
your dealer.

• Do not place the projector near water (ex. a bathroom, a beach, etc.).

• Do not expose the projector to rain or moisture. Do not place the projector
outdoors.

• Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc
on or around the projector.

• Do not place metals, combustibles, etc on or around the projector.

• To avoid penetration of foreign objects, do not put the projector into a case
or bag together with any thing except the accessories of the projector,
signal cables and connectors.

Never disassemble and modify.

The projector contains high voltage components. Modification and/or disassembly of
the projector or accessories could result in fire or electrical shock.

• Never open the cabinet.

• Ask your dealer to repair and clean insider.

Do not give the projector any shock or impact.

If the projector should be shocked and/or broken, it could result in an injury,
and continued use could result in fire or electrical shock.
If the projector is shocked, immediately turn off the power switch, disconnect
the power plug from the power outlet and contact your dealer.

Do not place the projector on an unstable surface.

If the projector should be dropped and/or broken, it could result in an injury,
and continued use could result in fire or electrical shock.

• Do not place the projector on an unstable, slant or vibrant surface such as

a wobbly or inclined stand.

• Use the caster brakes placing the projector on a stand with casters.

• Do not place the projector in the side up position, the lens up position or

the lens down position.

• In the case of a ceiling installation or the like, contact your dealer before

installation.

Disconnect the

plug from the
power outlet.

Do not

disassemble.

2

Safety Precautions (continued)

WARNING

Be cautious of High temperatures of the projector.

High temperatures are generated when the lamp is lit. It could result in fire or
burn. Use special caution in households where children are present.
Do not touch about the lens, air fans and ventilation openings during use or
immediately after use, to prevent a burn. Take care of ventilation.

• Keep a space of 30 cm or more between the sides and other objects such

as walls.

• Do not place the projector on a metallic table or anything weak in heat.

• Do not place anything about the lens, air fans and ventilation openings of

the projector.

• Never block the air fan and ventilation openings.

• Do not cover the projector with a tablecloth, etc.

• Do not place the projector on a carpet or bedding.

Never look through the lens or openings when the lamp is on.

The powerful light could adversely affect vision.
Use special caution in households where children are present.

Use only the correct power cord and the correct power outlet.

Incorrect power supply could result in fire or electrical shock.

• Use only the correct power outlet depending on the indication on the

projector and the safety standard.

• The enclosed power cord must be used depending on the power outlet to

be used.

Be cautious of the power cord connection.

Incorrect connection of the power cord could result in fire or electrical shock.

• Do not touch the power cord with a wet hand.

• Check that the connecting portion of the power cord is clean (with no dust),

before using. Use a soft and dry cloth to clean the power plug.

• Insert the power plug into a power outlet firmly. Avoid using a loose,

unsound outlet or contact failure.

Be sure to connect with ground wire.

Connect the ground terminal of AC inlet of this unit with the ground terminal
provided at the building using the correct power cord; otherwise, fire or
electric shock can result.

• Don’t take the core of power cord away.

Surely connect

the ground wire.

3

Safety Precautions (continued)

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass.
The lamp can break with a loud bang, or burn out. When the bulb bursts,
it is possible for shards of glass to fly into the lamp housing, and for gas
containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.
Be careful in handling the power cord and external connection

cables.

If you keep using a damaged the power cord or cables, it can cause a fire
or electrical shock. Do not apply too much heat, pressure or tension to the
power cord and cables.
If the power cord or cables is damaged (exposed or broken core wires, etc.),
contact your dealer.

• Do not place the projector or heavy objects on the power cord and cables.

Also, do not place a spread, cover, etc, over them because this could result
in the inadvertent placing of heavy objects on the concealed power cord or
cables.

• Do not pull the power cord and cables. When connecting and

disconnecting the power cord or cables, do it with your hand holding the plug
or connector.

• Do not place the cord near the heater.

• Avoid bending the power cord sharply.

• Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The
battery may explode if not handled properly.

• Keep the battery away from children and pets. If swallowed consult a

physician immediately for emergency treatment.

• Do not allow the battery in a fire or water.

• Avoid fire or high-temperature environment.

• Do not hold the battery with the metallic tweezers.

• Keep the battery in a dark, cool and dry play.

• Do not short circuit the battery.

• Do not recharge, disassemble or solder the battery.

• Do not give the battery a physical impact.

• Use only the battery specified in the other manual of this projector.

• Make sure the plus and minus terminals are correctly aligned when loading

the battery.

• If you observe a leakage of the battery, wipe out the flower and then

replace the battery. If the flower adheres your body or clothes, rinse well with
water.

• Obey the local laws on disposing the battery.

4

Safety Precautions (continued)

CAUTION

Be careful in moving the projector.

Neglect could result in an injury or damage.

• Do not move the projector during use. Before moving, disconnect the

power cord and all external connections, and close the slide lens door or
attach the lens cap.

• Avoid any impact or shock to the projector.

• Do not drag the projector.

• For moving the projector, use the enclosed case or bag if provided.

Do not put anything on top of the projector.

Placing anything on the projector could result in loss of balance or falling,
and cause an injury or damage. Use special caution in households where
children are present.

Do not attach anything other than specified things to the projector.

Neglect could result in an injury or damage.

• Some projector has a screw thread in a lens part. Do not attach anything

other than specified options (such as conversion lens) to the screw thread.

Avoid a smoky, humid or dusty place.

Placing the projector in a smoke, a highly humid, dusty place, oily soot or
corrosive gas could result in fire or electrical shock.

• Do not place the projector near a smoky, humid or dusty place (ex.

a smoking space, a kitchen, a beach, etc.). Do not place the projector
outdoors.

• Do not use a humidifier near the projector.

Take care of the air filter to normal ventilate.

The air filter should be cleaned periodically. If the air filter becomes clogged
by dust or the like, internal temperature rises and could cause malfunction.
The projector may display the message such as “CHECK THE AIR FLOW”
or turn off the projector, to prevent the internal heat level rising.

• When the indicators or a message prompts you to clean the air filter, clean

the air filter as soon as possible.

• If the soiling will not come off the air filter, or it becomes damaged, replace

the air filter.

• Use the air filter of the specified type only. Please order the air filter

specified in the other manual of this projector to your dealer.

• When you replace the lamp, replace also the air filter. The air filter may be

attached when you buy a replacement lamp for this projector.

• Do not turn on the projector without air filter.

Avoid a high temperature environment.

The heat could have adverse influence on the cabinet of the projector and
other parts. Do not place the projector, the remote control and other parts in
direct sunlight or near a hot object such as heater, etc.

Avoid Magnetism.

Manufacture strongly recommends to avoid any magnetic contact that is not
shielded or protected on or near the projector itself. (ie.,. Magnetic Security
Devices, or other projector accessory that contains magnetic material that has not
been provided by the manufacture etc.) Magnetic objects may cause interruption
of the projector's internal mechanical performance which may interfere with cooling
fans speed or stopping, and may cause the projector to completely shut down

.

5

Safety Precautions (continued)

CAUTION

Remove the power cord for complete separation.

• For safety purposes, disconnect the power cord if the projector is not to be

used for prolonged periods of time.

• Before cleaning, turn off and unplug the projector. Neglect could result in

fire or electrical shock.

Ask your dealer to cleaning inside of the projector about every
year.

Accumulations of dust inside the projector cause result in fire or malfunction.
Cleaning inside is more effective if performed before every humid periods
such as rainy season.

• Do not clean inside yourself because it is dangerous.

NOTE

Do not give the remote control any physical impact.

A physical impact could cause damage or malfunction of the remote control.

• Take care not to drop the remote control.

• Do not place the projector or heavy objects on the remote control.

Take care of the lens.

• Close the slide lens door or attach the lens cap to prevent the lens surface being

scratched when the projector is not used.

• Do not touch the lens to prevent fog or dirt of the lens that cause deterioration of display

quality.

• Use commercially available lens tissue to clean the lens (used to clean cameras,

eyeglasses, etc.). Be careful not to scratch the lens with hard objects.

Take care of the cabinet and the remote control.

Incorrect care could have adverse influence such as discoloration, peeling paint, etc.

• Use a soft cloth to clean the cabinet and control panel of the projector and the remote

control. When excessively soiled dilute a neutral detergent in water, wet and wring out the
soft cloth and afterward wipe with a dry soft cloth. Do not use undiluted detergent directly.

• Do not use an aerosol sprays, solvents, volatile substances or abrasive cleaner.

• Before using chemical wipes, be sure to read and observe the instructions.

• Do not allow long-term close contact with rubber or vinyl.

About bright spots or dark spots.

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of
liquid crystal displays, and such do not constitute or imply a machine defect.

Be careful of printing of the LCD panel.

If the projector continues projecting a still image, inactive images or 16:9 aspect images in
case of 4:3 panel, etc., for long time, the LCD panel might possibly be printed.

Disconnect the

plug from the
power outlet.

6

Safety Precautions (continued)

NOTE

About consumables.

Lamp, LCD panels, polarizors and other optical components, and air filter and cooling fans
have a different lifetime in each. These parts may need to be replaced after a long usage
time.

• This product isn’t designed for continuous use of long time. In the case of continuous use

for 6 hours or more, or use for 6 hours or more every day (even if it isn’t continuous), or
repetitious use, the lifetime may be shortened, and these parts may need to be replaced
even if one year has not passed since the beginning of using.

• Any inclining use beyond the adjustment range explained in these user’s manuals may
shorten the lifetimes of the consumables.

Before turning on the power, make the projector cool down adequately.

After turning the projector off, pushing the restart switch or interrupting of the power supply,
make the projector cool down adequately. Operation in a high temperature state of the
projector causes a damage of the electrode and un-lighting of the lamp.

Avoid strong rays.

Any strong ray (such as direct rays of the sun or room lighting) onto the remote control
sensors could invalidate the remote control.

Avoid radio interference.

Any interfering radiation could cause disordered image or noises.

• Avoid radio generator such as a mobile telephone, transceiver, etc. around the projector.

About displaying characteristic.

The display condition of the projector (such as color, contrast, etc.) depends on
characteristic of the screen, because the projector uses a liquid crystal display panel. The
display condition can differ from the display of CRT.

• Do not use a polarized screen. It can cause red image.

Turn the power on/off in right order.

To prevent any trouble, turn on/off the projector in right order mentioned below unless
specifying.

• Power on the projector before the computer or video tape recorder.

• Power off the projector after the computer or video tape recorder.

Take care not to fatigue your eyes.

Rest the eyes periodically.

Set the sound volume at a suitable level to avoid bothering other people.

• It is better to keep the volume level low and close the windows at night to protect the

neighborhood environment.

Connecting with notebook computer

When connecting with notebook computer, set to valid the RGB external image output
(setting CRT display or simultaneous display of LCD and CRT).
Please read instruction manual of the notebook for more information.

7

Lamp

WARNING

The projector uses a high-pressure mercury glass lamp. The lamp can break with a
loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time.

Note that each lamp has a different lifetime, and some may burst or burn out soon after
you start using them. In addition, when the bulb bursts, it is possible for shards of
glass to fly into the lamp housing, and for gas containing mercury to escape from the
projector’s vent holes.

About disposal of a lamp • This product contains a mercury lamp; do not put in trash.
Dispose of in accord with environmental laws.
For lamp recycling, go to www.lamprecycle.org. (in USA)
For product disposal, contact your local government agency or www.eiae.org (in the US)
or www.epsc.ca (in Canada).
For more information, call your dealer.

• If the lamp should break (it will make a loud bang when it does), unplug
the power cord from the outlet, and make sure to request a replacement
lamp from your local dealer. Note that shards of glass could damage the
projector’s internals, or cause injury during handling, so please do not try to
clean the projector or replace the lamp yourself.

Disconnect

the plug from

the power

outlet

• If the lamp should break (it will make a loud bang when it does), ventilate
the room well, and make sure not to breathe the gas that comes out of the
projector vents, or get it in your eyes or mouth.

• Before replacing the lamp, make sure the power switch is off and the
power cable is not plugged in, then wait at least 45 minutes for the lamp to
cool sufficiently. Handling the lamp while hot can cause burns, as well as
damaging the lamp.

HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE

• Do not open the lamp cover while the projector is suspended from above.
This is dangerous, since if the lamp’s bulb has broken, the shards will
fall out when the cover is opened. In addition, working in high places is
dangerous, so ask your local dealer to have the lamp replaced even if the
bulb is not broken.

• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose screws
could result in damage or injury.

• Use the lamp of the specified type only.

• If the lamp breaks soon after the first time it is used, it is possible that
there are electrical problems elsewhere besides the lamp. If this happens,
contact your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst
during use.

• Using the lamp for long periods of time, could cause it dark, not to light up
or to burst. When the pictures appear dark, or when the color tone is poor,
please replace the lamp as soon as possible. Do not use old (used) lamps;
this is a cause of breakage.

8

Regulatory Notices

FCC Statement Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.

WARNING: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver

is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC

(Federal Communication Commission) equipment provided that the following conditions
are met. Some cables have to be used with the core set. Use the accessory cable or a
designated-type cable for the connection. For cables that have a core only at one end,
connect the core to the projector.

CAUTION: Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA
NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of
WARNING in this manual), when a problem occurs with the equipment, first refer to the
“Troubleshooting” section of the “Operating Guide”, and run through the suggested checks.
If this does not resolve the problem contact your dealer or service company. They will tell
you what warranty condition is applied.

9

Contents

Introduction . ..............3



SETUP menu ..............45

Features . .....................3

Checking the contents of package

... 3

Part names . ...................4

Setting up . ................7

Arrangement ...................7

Connecting with your devices
Connecting to a power supply

......9

.....14

Using the security bar and slot . . . . 15

AUDIO menu . .............48

SCREEN menu .............50

Using the cable cover ...........16

Remote control ............17

Installing the batteries ...........17

About the remote control signal . . . 17
Changing the frequency of remote control signal
Using as a simple PC mouse & keyboard

..18

. . 18

OPTION menu . ............56

Interactive pen . ...........19

Power on/off . .............20

Operating . ...............22

NETWORK menu ...........67

Adjusting the volume ............22

Temporarily muting the sound .....22

Selecting an input signal .........22

Searching an input signal . .......24

SECURITY menu ...........74

Selecting an aspect ratio ......... 24

Adjusting the projector's elevator . . 25

Adjusting the zoom and focus .....25

Using the automatic adjustment feature

Adjusting the position . ..........27

Correcting the keystone distortions

... 26

Presentation tools . ........80

.. 27

Using the magnify feature ........28

Temporarily freezing the screen . . . 29
Temporarily blanking the screen . . 29

Using the menu function . .......30

EASY MENU. . . . . . . . . . . . . . . 32

INTERACTIVE, ASPECT,

KEYSTONE, PERFECT FIT

D-ZOOM,

, PICTURE MODE,

KEYSTONE,

Maintenance .............101

ECO MODE, MIRROR, RESET, FILTER TIME,
L

ANGUAGE, ADVANCED MENU, EXIT

INTERACTIVE menu . .......34

INTERACTIVE

PICTURE menu . ...........35

BRIGHTNESS, CONTRAST, GAMMA, COLOR TEMP,

Troubleshooting . .........109

COLOR, TINT, SHARPNESS, ACTIVE IRIS, MY MEMORY

IMAGE menu . .............38

ASPECT, OVER SCAN, V POSITION, H POSITION,
H

PHASE, H SIZE, AUTO ADJUST EXECUTE

INPUT menu . .............41

PROGRESSIVE, VIDEO NR, COLOR SPACE,
V

IDEO FORMAT, HDMI FORMAT, HDMI RANGE,

C

OMPUTER IN, FRAME LOCK, RESOLUTION

2

Specifications ............122



D-ZOOM, D-SHIFT, PICT.POSIT.H,

KEYSTONE, KEYSTONE, PERFECT FIT

UTO ECO MODE, ECO MODE,

A
S

TANDBY MODE, MONITOR OUT

MIRROR,

,

VOLUME, SPEAKER, AUDIO SOURCE,
H

DMI AUDIO, MIC LEVEL, MIC VOLUME

LANGUAGE, MENU POSITION, BLANK,
S

TAR T UP,

M

ESSAGE, SOURCE NAME, TEMPLATE, C.C.

M

yScreen

, M

yScreen Lock

,

AUTO SEARCH, DIRECT POWER ON,
A

UTO POWER OFF, USB TYPE B, LAMP TIME,

F

ILTER TIME, MY BUTTON, MY SOURCE,

S

ERVICE

SETUP, PROJECTOR NAME, MY IMAGE,
A

MX D.D., PRESENTATION, INFORMATION,

S

ERVICE

SECURITY PASSWORD CHANGE,

M

T
M

Interactive Function
PC-LESS Presentation

PASSWORD, PIN LOCK,

yScreen

RANSITION DETECTOR, MY TEXT PASSWORD,

Y TEXT DISPLAY, MY TEXT WRITING

.........80

.......87

Thumbnail Mode, Full Screen Mode,
Slideshow mode, Playlist

USB Display

..............

96

Right-Click menu, Floating menu,
Options window

Replacing the lamp ............101

Cleaning and replacing the air filter . 103

Replacing the internal clock battery
Caring for the mirror and lens

. . 105

......106

Other care ...................107

Related messages . ...........109

Regarding the indicator lamps . . . 111

Resetting all settings ........... 113

Phenomena that may be easy
to be mistaken for machine defects

.. 113

Introduction

Introduction

Features

The projector provides you with the broad use by the following features.

 The unique lens and mirror system realizes ultra short distance

projection,which gives you more various way of use.

 The motorized lens door offers you very simple use of the projector.

The double layer filter system is expected to function longer and offers you



less maintenance frequency.

 The HDMI port can support various image equipment which have digital

interface to get clearer pictures on a screen.

 This projector can be controlled and monitored via LAN connection.
 This projector's network supports the PJLink
 The Interactive Pen included with the projector allows you to write or

draw directly on the projected image. Also, you can control the connected
computer on the screen in the same way as using a mouse.

TM

 PJLink

PJLinkTM enables central control of projectors manufactured by different vendors

is a unified standard for operating and controlling data projectors.

and projectors can be operated by a controller. PJLink
can be managed and controlled at any time and in any place, regardless of
manufacturer.
For the command of PJLink
For specifications of PJLink
and Information System Industries Association.

URL: http://pjlink.jbmia.or.jp (as of Jun. 2011)

TM

, see “Technical”.

TM

, see the web site of the Japan Business Machine

TM

standard.

TM

compliant equipment

Checking the contents of package

Please see the Contents of package section in the User’s Manual (concise)
which is a book. Your projector should come with the items shown there. Require
of your dealer immediately if any items are missing.

NOTE

to use the original packing materials when moving the projector. Use special
caution for the lens.

• Keep the original packing materials, for future reshipment. Be sure

3

Introduction

Part names

Projector

(1) Lamp cover (101)

The lamp unit is inside.
(2) Control panel (
(3) Elevator feet (x 2) (25)
(4) Remote sensor (17)
(5) Lens (

106)
(6) Intake vents
(7) Filter cover (103)

The air filter and intake vent
are inside.

(8) Battery cover

The internal clock battery is

inside.
(9) Speaker (
(10) Exhaust vent
(11) AC IN (AC inlet) (
(12) Ports (5)
(13) Security bar (15)
(14) Security slot (15)
(15) Lens door (
(16) Mirror (106)
(17) Spacer (Small) (25)
(18) Spacer (Large) (25)
(19) PEN sensor (

5)

12, 22, 48)

14)

106)

107)

(17)

Small

(4)

(3)

(7)

(5)

(6)

(1)

(8)

(15)

HOT!

(2)

(13)

(11)

(18)

Large

(16)

(12)

(14)

(10)

HOT!

(9)

(19)

WARNING

►HOT! : Do not touch around the lamp cover and the exhaust
vents during use or just after use, since it is too hot.

►Be careful not to pinch your finger with the lens door, to prevent an injury.

►Never look into the projection lens or mirror while the projection lamp lights,

since the projection lamp ray may cause a trouble on your eyes.

►Do not use the security bar and slot to prevent the projector from falling down,
since it is not designed for it.

CAUTION

►Maintain normal ventilation to prevent the projector from
heating up. Do not cover, block or plug up the vents. Do not place anything that
can stick or be sucked to the vents, around the intake vents. Clean the air filter
periodically.

4

Control panel

Introduction

(1) STANDBY/ON button (20)
(2) INPUT button (
(3) POWER indicator (
(4) TEMP indicator (

22)

20, 111, 112)

111, 112)

(3)

(4)

(6)

(5) LAMP indicator (111, 112)
Buttons ◄/►/▲/▼
(6) FOCUS +/- buttons

when no menu is displayed (26),

(5)

(7)

(2)

(1)

or Cursor ◄/► buttons when a menu is displayed (30). FOCUS +/- function

is invalid when the USB TYPE A port is selected as the input source.

(7) MENU buttons

when no menu is displayed (30), or Cursor ▲/▼ buttons when a menu is
displayed (

30).

The ◄/►/▲/▼ buttons on the projector work only as the cursor buttons while the
template is displayed (54).

Ports (
(1) USB TYPE A port

(2) LAN port
(3) HDMI port
(4) USB TYPE B port
(5) MIC port
(6) AUDIO IN1 port
(7) AUDIO IN2 port
(8) AUDIO IN3 (L,R)

9 ~ 13)

(9) AUDIO OUT (L,R) ports
(10) COMPUTER IN1 port
(11) COMPUTER IN2 port
(12) MONITOR OUT port
(13) CONTROL port
(14) VIDEO port
(15) S-VIDEO port

ports

USB
TYPE A
DC5V

0.5A

LAN

(2)

(1)

CONTROL

(4)

USB TYPE B

MONITOR OUT

(13) (15)

(3) (11)

HDMI

MIC

AUDIO IN2

(7)

(5) (9)

AUDIO IN3AUDIO IN1

R

L

(6)(12)

(8) (14)

(10)

COMPUTER IN1COMPUTER IN2

AUDIO OUT

R

L

S-VIDEO

VIDEO

5

Introduction

Remote control

(1) VIDEO button (
(2) COMPUTER button (
(3) SEARCH button (
(4) STANDBY/ON button (

23)

23)

24)

20)

(5) ASPECT button (24)
(6) AUTO button (26)
(7) BLANK button (29)
(8) MAGNIFY - ON button (

28)

(9) MAGNIFY - OFF button (28)
(10) MY SOURCE/DOC.CAMERA button (23, 60)
(11) VOLUME - button (22)
(12) PAGE UP button (18)
(13) PAGE DOWN button (

18)

(14) VOLUME + button (22)
(15) MUTE button (22)
(16) FREEZE button (29)
(17) MY BUTTON - 1 button (

59)

(18) MY BUTTON - 2 button (59)
(19) KEYSTONE button (27)
(20) FOCUS - button (26)
(21) FOCUS + button (

26)

(22) D-ZOOM - button (25)
(23) D-ZOOM + button (25)
(24) POSITION button (27, 31)
(25) MENU button (30, 31)
(26) ▲/▼/◄/► cursor buttons (

30)

(27) ENTER button (30, 31)
(28) ESC button (30)
(29) RESET button (30)
(30) Battery cover (

17)

(2)
(1)
(6)
(5)
(16)
(8)
(9)
(19)

VIDEO

ASPECT

MAGNIFY

ON

OFF

KEYSTONE

(17)
(20)

POSITION

(21)
(24)
(26)
(28)

the remote control

MY SOURCE/

COMPUTER

DOC.CAMERA

AUTO

SEARCH

PAGE

FREEZE

MY BUTTON



FOCUS





ENTER

ESC

Back of

(10)
(4)
(3)

BLANK

VOLUME

UP

DOWN

MUTE



D-ZOOM



MENU

(7)
(12)

㧗

(14)

࡯

(11)
(13)



(15)
(18)
(23)
(22)

RESET

(25)
(27)
(29)

(30)

Interactive pen

(1) Pen tip (

19)
(2) SIDE BUTTON No.0 button (85)
(3) SIDE BUTTON No.1 button (85)
(4) Battery cover (19)

NOTE

• Interactive Pen is henceforth denoted as

“pen”.

6

(2)

(3)

(1)

(4)

Setting up

Setting up

Install the projector according to the environment and manner the projector will be
used in.

Arrangement

Refer to table T-1 and figures F-1 and F-2 at the end of User's Manual (concise) to determine
the screen size and projection distance.

The values shown in the table are calculated for a full size screen: 1280 x 800
a Screen size (diagonal)

• For the case of installation in special conditions such as on the wall or ceiling, the
specified mounting accessories and service may be required. Tabletop use must be
setup with the designated optional accessories. Before installing the projector, consult
your dealer about your installation.

•

The screen position may shift after installation if the projector is mounted on locations
such as the wall or ceiling, due to the flexibility of the plastic projector body. If readjustment
is necessary, consult with your dealer or service personnel.

• The projected image position and/or focus may change during warm-up (approx. 30
minutes after the lamp is turned on) or when the ambient conditions change. Readjust
the image position and/or focus as necessary.

• Since the projector features an ultra short throw, be aware that it is required to select a
screen carefully to have better performance.

- A soft screen such as a pull-down screen may cause serious distortion of a projected

image. A hard screen such as a board screen is recommended for use with this
projector.

- A high-gain screen such as a bead screen that has narrow viewing angle is not suitable

for this projector. A low-gain screen (around 1.0) such as a matte screen that has wide
viewing angle is recommended for use with this projector.

- A screen with a weave pattern may cause moiré on the projected image, which is not

a failure of the projector. A screen that has less moiré effects is recommended for use
with this projector.

b1 , b2

Projection distance (±8%)

c1 , c2

Screen height (±8%)

NOTE

• The projector may make a rattling sound when tilted, moved or
shaken, since a flap to control the air flow inside of the projector has moved. Be
aware that this is not a failure or malfunction.

►

WARNING

Place the projector in a stable horizontal position. If the
projector falls or is knocked over, it could cause injury and/or damage to the
projector. Using a damaged projector could then result in fire and/or electric shock.

• Do not place the projector on an unstable, slanted or vibrational surface such

as a wobbly or inclined stand.

• Do not place the projector on its side or front position. To place the projector

on its rear position for the table top use, it is required to use the designated
optional parts. Consult with your dealer.

•

Consult with your dealer before a special installation such as on the wall or ceiling.

(continued on next page)

7

Setting up

Arrangement (continued)

WARNING

►Place the projector in a cool place, and ensure that there is
sufficient ventilation. The high temperature of the projector could cause fire,
burns and/or malfunction of the projector.

• Do not stop-up, block or otherwise cover the projector's vents.

• Keep a space of 30 cm or more between the sides of the projector and other

objects such as walls.

• Do not place or attach anything that would block the lens or vent holes.

• Do not place the projector on metallic thing or anything weak in heat.

• Do not place the projector on carpet, cushions or bedding.

• Do not place the projector in direct sunlight or near hot objects such as heaters.

Do not place the projector where the air from an air conditioner or similar unit
will blow on it directly.

•

Do not place anything near the projector lens or vents, or on top of the projector.

•

Do not place anything that may be sucked into or stick to the vents on the

bottom of the projector. This projector has some intake vents also on the bottom.
►Do not place the projector anyplace where it may get wet. Getting the projector
wet or inserting liquid into the projector could cause fire, electric shock and/or
malfunction of the projector.

• Do not place the projector in a bathroom or the outdoors.

• Do not place anything containing liquid near the projector.

•

Do not place the projector where any oils, such as cooking or machine oil, are used.
►Use only the mounting accessories the manufacturer specified, and leave
installing and removing the projector with the mounting accessories to the
service personnel.

• Read and keep the user’s manual of the mounting accessories used.

CAUTION

►Avoid placing the projector in smoky, humid or dusty place.
Placing the projector in such places could cause fire, electric shock and/or
malfunction of the projector.

• Do not place the projector near humidifiers, smoking spaces or a kitchen. Also

do not use an ultrasonic humidifier near the projector. Otherwise chlorine and
minerals contained in tap water are atomized and could be deposited in the
projector causing image degradation or other problems.

►

Position the projector to prevent light from directly hitting the projector's remote sensor.
►Do not place the product in a place where radio interference may be caused.
►Do not place this product in a magnetic field.
►If the projector is used at an altitude of about 1600 m or higher, set FAN
SPEED of the SERVICE item in the OPTION menu to HIGH (

61). Otherwise,
set it to NORMAL. If the projector is used with a wrong setting, it may cause
damage to the projector itself or the parts inside.

8

Setting up

Connecting with your devices

Before connecting the projector to a device, consult the manual of the device to
confirm that the device is suitable for connecting with this projector and prepare
the required accessories, such as a cable in accord with the signal of the device.
Consult your dealer when the required accessory did not come with the product or
the accessory is damaged.
After making sure that the device and projector are turned off, connect them
following the instructions below.

►

WARNING

a fire or damage to the device and the projector.

- Use only the accessories specified or recommended by the projector’s

manufacturer. Consult your dealer when the required accessory did not come
with the product or the accessory is damaged. It may be regulated under some
standard.

- For a cable with a core at only one end, connect the end with the core to the

projector. That may be required by EMI regulations.

- Neither disassemble nor modify the projector and the accessories.

- Do not use the damaged accessory. Be careful not to damage the accessories.

Route a cable so that it is neither stepped on nor pinched out.

CAUTION

in operation, unless that is directed in the manual of the device. Otherwise it may
cause malfunction in the device or projector.
►Be careful not to mistakenly connect a connector to a wrong port. Otherwise it
may cause malfunction in the device or projector.

- When connecting a connector to a port, make sure that the shape of the

connector fits the port.

- Tighten the screws to connect a connector equipped with screws to a port.

- Use the cables with straight plugs, not L-shaped ones, as the input ports of the

projector are recessed.

Use only the appropriate accessories. Otherwise it could cause

►Do not turn on or off the projector while connected to a device

(continued on next page)

9

Setting up

Connecting with your devices (continued)

About Plug-and-Play capability

• Plug-and-Play is a system composed of a computer, its operating system
and peripheral equipment (i.e. display devices). This projector is VESA DDC
2B compatible. Plug-and-Play can be used by connecting this projector to a
computer that is VESA DDC (display data channel) compatible.

- Take advantage of this feature by connecting a computer cable to the
COMPUTER IN1 port (DDC 2B compatible). Plug-and-Play may not work
properly if any other type of connection is attempted.

-

Please use the standard drivers in your computer as this projector is a Plug-and­Play monitor.

• When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in
COMPUTER IN of the INPUT menu, that port will accept component video
signals (

•

When the USB TYPE B port and the computer's USB type A port are connected,

43).

you can use the USB TYPE B port as a picture input port from the computer, use
the remote control as a simple mouse and keyboard of the computer, or use the
Interactive Function (18, 57).

Computer

VCR/DVD/Blu-ray Disc

player

LAN

Cr/Pr

Cb/Pb

Y

COMPONENT

L

OUT

AUDIO

R

VIDEO

L

OUT

AUDIO

R

S-VIDEO

OUT

AUDIO

R

L

USB
TYPE A
DC5V

0.5A

LAN

(continued on next page)

10

CONTROL

USB TYPE B

MONITOR OUT

HDMI

MIC

AUDIO IN2

USB

(A)

HDMI

COMPUTER IN1COMPUTER IN2

DISPLAY

S-VIDEO

AUDIO OUT

AUDIO IN3AUDIO IN1

R

L

R

L

VIDEO

AUDIO

OUT

RS-232C

Connecting with your devices (continued)

Setting up

NOTE

• Before connecting the projector to a computer, consult the computer’s
manual and check the compatibility of the signal level, the synchronization
methods and the display resolution output to the projector.

- Some signal may need an adapter to input this projector.

- Some computers have multiple screen display modes that may include some

signals which are not supported by this projector.

- Although the projector can display signals with resolution up to UXGA

(1600X1200), the signal will be converted to the projector’s panel resolution
before being displayed. The best display performance will be achieved if the
resolutions of the input signal and the projector panel are identical.

• If you connect this projector and a notebook computer, you need output the
display to an external monitor, or output simultaneously to the internal display
and an external monitor. Consult the computer's manual for the setting.

• Depending on the input signal, the automatic adjustment function of this
projector may take some time and not function correctly.

- Note that a composite sync signal or sync-on-green signal may confuse the

automatic adjustment function of this projector (

43).

- If the automatic adjustment function does not work correctly, you may not see

the dialog to set the display resolution. In such a case, use an external display
device. You may be able to see the dialog and set an appropriate display
resolution.

• To use the Interactive Function, it is necessary to install the “StarBoard
Software” in the DVD-ROM on the computer.

(continued on next page)

11

Setting up

Connecting with your devices (continued)

• If you insert a USB storage device, such as a USB memory, into the USB TYPE
A port and select the port as the input source, you can view images stored in the

device (87).

• You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug.
In that case, the built-in speaker outputs the sound from the microphone, even
while the sound from the projector is output. You can input line level signal to the
MIC port from equipment such as wireless microphone. Select HIGH in the MIC
LEVEL item of the AUDIO menu when you input line level audio signal to the
MIC port. In the normal mode, the volume of the microphone can be adjusted
separately from the volume of the projector using the menu (49).

In the standby mode, the volume of the microphone is adjustable with the

VOLUME +/- buttons on the remote control, in synchronization with the volume
of the projector (22).

Even when the sound of projector is set to mute mode by the AUDIO SOURCE

function (

48), the volume of the microphone is adjustable.

In both modes (standby or normal), the MUTE button on the remote control

works on the sounds of the microphone and the projector (22).

Monitor

Microphone system

RGB IN

Speakers

(with an amplifier)

R

L

USB storage

CAUTION

device

USB
TYPE A
DC5V

0.5A

LAN

CONTROL

USB TYPE B

MONITOR OUT

HDMI

MIC

AUDIO IN2

►Before removing the USB storage device from the port of the

COMPUTER IN1COMPUTER IN2

S-VIDEO

AUDIO OUT

AUDIO IN3AUDIO IN1

R

L

R

L

VIDEO

projector, be sure to use the REMOVE USB function on the thumbnail screen to
secure your data (90).

NOTE

• If a loud feedback noise is produced from the speaker, move the

microphone away from the speaker.

• This projector doesn't support plug-in power for the microphone.

(continued on next page)

12

Setting up

Connecting with your devices (continued)

To use network functions of the projector, connect the LAN port with the
computer's LAN port, or with an access point that is connected to the computer
with wireless LAN, using a LAN cable. To use NETWORK BRIDGE function,
also connect the CONTROL port and an RS-232C port of the external device to
communicate as a network terminal. See the User's Manual - Network Guide for
details of the network functions.

Access point Computer

LAN

RS-232C

COMPUTER IN1COMPUTER IN2

S-VIDEO

AUDIO OUT

AUDIO IN3AUDIO IN1

R

L

R

L

VIDEO

CAUTION

HDMI

CONTROL

USB TYPE B

MIC

MONITOR OUT

AUDIO IN2

USB
TYPE A
DC5V

0.5A

LAN

►Before connecting the projector to a network system be sure
to obtain the consent of the administrator of the network (67).
►

Do not connect the LAN port to any network that might have the excessive voltage.

NOTE

• If an oversized USB storage device blocks the LAN port, use a USB

extension cable to connect the USB storage device.

13

Setting up

Connecting to a power supply

Put the connector of the power cord into the

1.

AC IN (AC inlet) of the projector.
Firmly plug the power cord’s plug into the

2.

outlet. In a couple of seconds after the
power supply connection, the POWER
indicator will light up in steady orange.
Please remember that when the DIRECT
POWER ON function activated (
connection of the power supply make the
projector turn on.

Make sure that the cover is not attached to

3.

the pen sensor when the interactive pen is
used.

56), the

AC IN

Power cord

PEN sensor

WARNING

incorrect or faulty connections may result in fire and/or electrical shock.

• Do not touch the power cord with a wet hand.

• Only use the power cord that came with the projector. If it is damaged, consult

your dealer to get a new one. Never modify the power cord.

• Only plug the power cord into an outlet whose voltage is matched to the power

cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.

• Do not distribute the power supply to multiple devices. Doing so may overload

the outlet and connectors, loosen the connection, or result in fire, electric shock
or other accidents.

• Keep the sensor cover away from children and pets. Be careful so that they do

not put it into their mouth.

NOTICE ►Please ensure that dust is not adhered to the pen sensor as it will
deteriorate the performance of the sensor. With the exception of installing the
projector in high places, you can use the sensor cover provided to keep the pen
sensor from getting dusty when it is not in use. Take care not to lose the cover
for the pen sensor when it is not in use.

►Please use extra caution when connecting the power cord, as

14

Using the security bar and slot

A commercial anti-theft chain or wire up to
10 mm in diameter can be attached to the
security bar on the projector.
Also this product has the security slot for
the Kensington lock.
For details, see the manual of the security
tool.

Anti-theft chain or wire

Setting up

Security slot

Security bar

WARNING

►Do not use the security bar and slot to prevent the projector
from falling down, since it is not designed for it.

CAUTION

►Do not place anti-theft chain or wire near the exhaust vents.
It may become too hot.

NOTE

• The security bar and slot is not comprehensive theft prevention

measures. It is intended to be used as supplemental theft prevention measure.

15

Using the cable cover

Utilize the cable cover as the guard and blind for the connecting parts.

Connect the signal cables and the power cord to the projector first.

1.

Combine parts as shown in figure,

2.

and assemble the cable cover.

3

Setting up

1

1

Insert the three knobs on the cable cover into the three holes on the projector

3

.

as shown in the figure. Pass the cables through the holes on the bottom of

3

the cable cover.

1

1

2

3

3

2

knobs

2

2

CAUTION

►Be careful not to pinch the cables in the cable cover, to
prevent damage to the cables.
►Use the cable cover that is supplied with the projector. Do not attempt any
modifications to the cable cover.

16

Remote control

Remote control

Installing the batteries

Please insert the batteries into the remote control before using it. If the remote control
starts to malfunction, try to replace the batteries. If you will not use the remote control for
long period, remove the batteries from the remote control and store them in a safe place.

Holding the hook part of the battery

1.

cover, remove it.
Align and insert the two AA batteries

2.

(HITACHI MAXELL or HITACHI MAXELL
ENERGY, Part No.LR6 or R6P) according

to their plus and minus terminals as indicated in the remote control.
Replace the battery cover in the direction of the arrow and snap it back into place.

3.

213

WARNING

directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fi re, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specifi ed. Do not use batteries of different

types at the same time. Do not mix a new battery with used one.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a fi re or water. Keep batteries in a dark, cool and dry place.

•

If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

About the remote control signal

The remote control works with the projector’s remote
sensor. This projector has a remote sensor on the front.
The sensor senses the signal within the following range
when the sensor is active:

60 degrees (30 degrees to the left and right of the sensor)
within 3 meters about.

NOTE

If it is diffi cult to send the signal to the sensor directly, attempt to make the signal refl ect.

• The remote control uses infrared light to send signals to the projector (Class 1
LED), so be sure to use the remote control in an area free from obstacles that
could block the remote control’s signal to the projector.

•

The remote control may not work correctly if strong light (such as direct sun
light) or light from an extremely close range (such as from an inverter fl uorescent
lamp) shines on the remote sensor of the projector. Adjust the position of
projector avoiding those lights.

•

►Always handle the batteries with care and use them only as

Remote

sensor

30º

30º

Approx.

3 m

The remote control signal refl ected in the screen or the like may be available.

17

Remote control

Changing the frequency of remote control signal

The accessory remote control has the two choices on signal
frequency Mode 1:NORMAL and Mode 2:HIGH. If the remote control
does not function properly, attempt to change the signal frequency.
In order to set the Mode, please keep pressing the combination of
two buttons listed below simultaneously for about 3 seconds.

(1) Set to Mode 1:NORMAL... VOLUME - and RESET buttons
(2) Set to Mode 2:HIGH... MAGNIFY OFF and ESC buttons

Please remember that the REMOTE FREQ. in the SERVICE item of
the OPTION menu (

63)

of the projector to be controlled should be

set to the same mode as the remote control.

ON

OFF

ASPECT

MAGNIFY

KEYSTONE

POSITION

FOCUS



ESC

Using as a simple PC mouse & keyboard

The accessory remote control works as a simple mouse
and keyboard of the computer, when the projector’s USB
TYPE B port and the computer’s type A USB port are
connected and MOUSE is selected for the USB TYPE B
item in the OPTION menu (

57).

(1) PAGE UP key: Press PAGE UP button.
(2) PAGE DOWN key: Press PAGE DOWN button.
(3) Mouse left button: Press ENTER button.
(4)

Move pointer: Use the cursor buttons ▲, ▼, ◄ and ►.
(5) ESC key: Press ESC button.
(6) Mouse right button: Press RESET button.

NOTICE

►Improper use of the simple mouse & keyboard
function could damage your equipment. While using this
function, please connect this product only to a computer. Be
sure to check your computer’s manuals before connecting this
product to the computer.

USB TYPE B

USB TYPE B

port

(3)

(5)

OFF

VIDEO

ASPECT

MAGNIFY

ON

KEYSTONE

POSITION

FOCUS



ESC

AUTO

FREEZE



COMPUTER

AUTO

FREEZE



MY BUTTON



MY BUTTON



ENTER

ENTER

SEARCH

PAGE

DOWN



MY SOURCE/

DOC.CAMERA

SEARCH

PAGE

DOWN



BLANK

VOLUME

UP

㧗

࡯

MUTE



(1)(2)

D-ZOOM



MENU

RESET

BLANK

(1)

VOLUME

UP

㧗

࡯

(2)

MUTE



D-ZOOM



MENU

(4)

RESET

(6)

NOTE

When the simple mouse & keyboard function of this product does not work

correctly, please check the following.

• When a USB cable connects this projector with a computer having a built-in pointing
device (e.g. track ball) like a laptop Computer, open BIOS setup menu, then select the
external mouse and disable the built-in pointing device, because the built-in pointing
device may have priority to this function.

Windows 95 OSR 2.1 or higher is required for this function. And also this function may not work

•
depending on the computer’s configurations and mouse drivers. This function can work with the
computer which can operate general USB mouse or keyboard.

• You cannot do things like press two buttons at once (for instance, pressing two buttons
at the same time to move the mouse pointer diagonally).

This function is activated only when the projector is working properly. This function is not

•
available in any of the following cases:

- While the lamp is warming up. (The POWER indicator blinks in green.)

- When either USB TYPE A or USB TYPE B port is selected.

- While displaying BLANK

, TEMPLATE

(54)

or MY IMAGE

(70)

screen.

(29)

- When any menu is displayed on the screen.
While using the cursor buttons to operate the sound or screen functions such as adjusting the

-
sound volume, correcting the keystone, correcting the picture position and magnifying the screen.

18

Interactive pen

Interactive pen

Installing the battery

Turn the battery cover of the pen to the left to open

1.

it.
As illustrated in the diagram, insert the AAA battery

2.

into the battery cover with the - end facing the front.

(HITACHI MAXELL or HITACHI MAXELL ENERGY,
Part No. LR03)

Attach the battery cover by turning it to the right

3.

until it is completely closed.

Exchanging the tip of the pen

When the tip of the pen is shortened due to wearing,
exchange it according to the following procedure.

Remove the tip of the pen referring to the

1.

illustration.
Fit a new tip into the place and push it so that it

2.

clicks.

The tip of
the pen

WARNING

directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fire, injury and/or pollution of the surrounding environment.

• Be sure to use only the batteries specified.

• Do not hold a battery with tweezers or the like.

•

Make sure the plus and minus terminals are correctly aligned when loading a battery.

• Keep a battery away from children and pets.

• Do not recharge, short circuit, solder or disassemble a battery.

•

Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.

•

If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.

• Obey the local laws on disposing the battery.

• Keep the tip of the pen away from children and pets. Exercise care to prevent
them from swallowing the tip of the pen or the pack of spare accidentally. If
swallowed consult a physician immediately for emergency treatment.

►Always handle the batteries with care and use them only as

► Do not drop the pen or mishandle it.CAUTION

19

Power on/off

Turning on the power

Make sure that the power cord is firmly

1.

and correctly connected to the projector
and the outlet.

Make sure that the POWER indicator is

2.

steady orange (111).
Confirm that there is nothing that the lens

3.

door hits while opening. Press STANDBY/
ON button on the projector or the
remote control. The lens door opens, the
projection lamp lights up, and the POWER
indicator begins to blink green. When the
power is completely on, the indicator will
stop blinking and light in steady green
(

111).

WARNING ►Never look into the projection lens or mirror while

the projection lamp lights, since the projection lamp ray may cause
a trouble on your eyes.
►Be careful not to pinch your finger with the lens door, to prevent
an injury.
►Do not place the projector vertically with the lens door open
as shown in the figure on the right. It could cause malfunction or
injury. Tabletop use must be set up with the designated optional
accessories.
►Do not stand under the projector mounted on the wall or ceiling,
when its lens door is opening or closing. Moreover, do not look at
the mirror when the lens door is opening or closing.
►Never touch a lens door or mirror. If the mirror is broken, the
projected image will be distorted. Close the lens door, and contact
your dealer.

STANDBY/ON button
POWER indicator

Power on/off

MY SOURCE/

VIDEO

COMPUTER

DOC.CAMERA

ASPECT

AUTO

SEARCH

BLANK

MAGNIFY

PAGE

VOLUME

FREEZE

UP

ON

㧗

DOWN

OFF

࡯

MY BUTTON

MUTE

KEYSTONE





D-ZOOM

FOCUS









MENU

POSITION

ENTER

ESC

RESET

20

Power on/off

Turning off the power

Press the STANDBY/ON button on the projector or the remote control.

1.

The message “Power off?” will appear on the screen for about 5 seconds.
Confirm that there is nothing that the lens door

2.

hits while closing.
Press the STANDBY/ON button again while the
message appears.
If the pen sensor is within easy reach, attach
the sensor cover provided to keep it from
getting dusty.
The projector lamp will go off, and the POWER indicator will begin blinking in
orange. The lens door will close right after the lamp goes off.
However, to maintain better picture quality, the lens door will close after the
lamp has been cooled down when the projector is installed upside down such
as in ceiling mount installation. Then POWER indicator will stop blinking and
light in steady orange when the lamp cooling is complete (

Do not turn the projector on for about 10 minutes or more after turning it off.
Also, do not turn the projector off shortly after turning it on. Such operations might
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.

111).

WARNING

prevent an injury.

►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be
close to the projector and easily accessible.

NOTE

prior to the connected devices.

•

This projector has the function that can make the projector automatically turn on/

off. Please refer to the DIRECT POWER ON
items of the OPTION menu.

• Turn the power on/off in right order. Please power on the projector

►Be careful not to pinch your finger with the lens door, to

(56)

and AUTO POWER OFF

(57)

21