Page 1
DS-6700HQHI-SATA Series Encoder Quick Start Guide
1
DS-6700HQHI-SATA Encoder
Quick Start Guide
UD.6L0202B2169A0
Page 2
DS-6700HQHI-SATA Series Encoder Quick Start Guide
1
Quick Start Guide
COPYRIGHT ©2015 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of Hangzhou
Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be “Hikvision”). This user
manual (hereinafter referred to be “the Manual”) cannot be reproduced, changed, translated, or distributed,
partially or wholly, by any means, without the prior written permission of Hikvision. Unless otherwise stipulated,
Hikvision does not make any warranties, guarantees or representations, express or implied, regarding to the
Manual.
About this Manual
This Manual is applicable to DS-6700HQHI-SATA Series Encoder.
The Manual includes instructions for using and managing the product. Pictures, charts, images and all other
information hereinafter are for description and explanation only. The information contained in the Manual is
subject to change, without notice, due to firmware updates or other reasons. Please find the latest version in the
company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH
ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND
ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR
PURPOSE, AND NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS
DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL,
CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS,
DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR
DOCUMENTATION, IN CONNECTION WITH THE USE OF THIS PRODUCT, EVEN IF HIKVISION HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR
ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER
ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;
HOWEVER, HIKVISION WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS
USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE
LATER PREVAILS.
Page 3
DS-6700HQHI-SATA Series Encoder Quick Start Guide
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE" and comply
therefore with the applicable harmonized European standards listed under the EMC Directive
2004/108/EC, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection
points. For more information see: www.recyclethis.info
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted
municipal waste in the European Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a
designated collection point. For more information see: www.recyclethis.info
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.
Page 4
DS-6700HQHI-SATA Series Encoder Quick Start Guide
3
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or
end-user.
● In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation
and region. Please refer to technical specifications for detailed information.
● Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with
100~240 VAC, 48VDC or 12 VDC according to the IEC60950-1 standard. Please refer to technical
specifications for detailed information.
● Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire
hazard.
● Please make sure that the plug is firmly connected to the power socket.
● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then
please contact the service center.
Warnings Follow these
safeguards to prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.
Page 5
DS-6700HQHI-SATA Series Encoder Quick Start Guide
4
Preventive and Cautionary Tips
Before connecting and operating your device, please be advised of the following tips:
• Ensure unit is installed in a well-ventilated, dust-free environment.
• Unit is designed for indoor use only.
• Keep all liquids away from the device.
• Ensure environmental conditions meet factory specifications.
• Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it
may cause damage to the sensitive electronics within the unit.
• Use the device in conjunction with an UPS if possible.
• Power down the unit before connecting and disconnecting accessories and peripherals.
• A factory recommended HDD should be used for this device.
• Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or
equivalent type only. Dispose of used batteries according to the instructions provided by the battery
manufacturer.
Page 6
DS-6700HQHI-SATA Series Encoder Quick Start Guide
5
Table of Content
Chapter 1 Panel Description ......................................................................................................................... 6
1.1 Front Panel ..................................................................................................................................................... 6
1.2 Rear Panel ...................................................................................................................................................... 6
Chapter 2 Installation .................................................................................................................................... 8
2.1 Pre-Installation ............................................................................................................................................... 8
2.2 Installation ...................................................................................................................................................... 8
2.3 Hard Disk Installation ..................................................................................................................................... 8
Chapter 3 Activation and Initializing Network Configuration for the Encoder ..................................... 10
3.1 Setting the Admin Password via Web Browser ............................................................................................ 10
3.2 Setting Admin Password and Modifying Network Parameters via Client Software ..................................... 11
Chapter 4 Access to DS-6700HQHI-SATA by Web Browser ................................................................... 14
4.2 Starting Live View ....................................................................................................................................... 15
4.3 Operating PTZ Control ................................................................................................................................. 15
4.4 Recording ..................................................................................................................................................... 16
4.5 Playback ....................................................................................................................................................... 18
4.6 Log ............................................................................................................................................................... 20
Page 7
DS-6700HQHI-SATA Series Encoder Quick Start Guide
6
Chapter 1 Panel Description
1.1 Front Panel
DS-6708HQHI-SATA/DS-6716HQHI-SATA:
Figure 1. 1 DS-6708HQHI-SATA/DS-6716HQHI-SATA Front Panel
Table 1. 1 Indicator Description
Indicator
Description
1
POWER
Lights in green when the device is powered on.
2
STATUS
Lights in green when data is being read from or written to HDD.
3
Tx/Rx
1. Does not light when the network is not connected;
2. Blinks in green when the data is transmitting/receiving;
3. Blinks at higher frequency when the data for transmitting/receiving is
larger.
1.2 Rear Panel
DS-6708HQHI-SATA:
Figure 1. 2 DS-6708HQHI-SATA Rear Panel
DS-6716HQHI-SATA:
Page 8
DS-6700HQHI-SATA Series Encoder Quick Start Guide
7
Figure 1. 3 DS-6716HQHI-SATA
Table 1. 2 Interface Description
Description
1
VIDEO IN
2
AUDIO IN, RCA Connector
3
AUDIO OUT, RCA Connector
4
LAN Network Interface
5
RS-485 Serial Interface
6
12 VDC Power Input
7
Power Switch
8
ALARM IN and ALARM OUT
9
GND
Page 9
DS-6700HQHI-SATA Series Encoder Quick Start Guide
8
Chapter 2 Installation
2.1 Pre-Installation
The DS-6700HQHI-SATA Series Encoder is advanced surveillance equipment that should be
installed with care. Please take into consideration the following precautionary steps before
installation of the Encoder.
1. Keep all liquids away from the Encoder.
2. Install the Encoder in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory specifications.
4. Install a manufacturer recommended HDD.
2.2 Installation
During the installation of the Encoder:
1. Use brackets for rack mounting.
2. Ensure there is ample room for audio and video cables.
3. When installing cables, ensure that the bend radius of the cables are no less than five times than
its diameter.
4. Connect both the alarm and RS-485 cable.
5. Allow at least 2cm (≈0.75") of space between racks mounted devices.
6. Ensure the Encoder is grounded.
7. Environmental temperature should be within the range of -10º C to 55º C, 14º F to 13º F.
8. Environmental humidity should be within the range of 10% to 90%.
2.3 Hard Disk Installation
Prior to Installation
The device is factory installed with no hard disk. Refer to the following instructions to install the
hard disk according to the total capacity calculated in terms of the Schedule Recording Settings. The
installation and removal of the hard disk should be operated by qualified professionals.
Before installing a hard disk drive, please make sure the power is disconnected from the device. A
factory recommended HDD should be used for this installation.
Tools Required: Screwdriver.
Steps:
1. Use the screwdriver to unfasten the screws on both sides and rear panel of the device, and then
remove the cover from the chassis.
Page 10
DS-6700HQHI-SATA Series Encoder Quick Start Guide
9
2. Place the HDD into the slot of the chassis and then secure it in position by fastening the screws
at the bottom of the chassis.
3. Take out the HDD data line from the accessories box. Plug one end of the data line to the
circuit board and the other end to the data line port of HDD. Connect the power cord to HDD
in the same way.
4. Replace the cover and then tighten the screws on both sides and rear panel of the device.
Page 11
DS-6700HQHI-SATA Series Encoder Quick Start Guide
10
Chapter 3 Activation and Initializing
Network Configuration for the Encoder
3.1 Setting the Admin Password via Web Browser
Steps:
1. Power on the encoder, and connect the encoder to the network.
2. Input the IP address into the address bar of the web browser, and click Enter to enter the activation interface.
The default IP address of the network encoder is 192.0.0.64. You are recommended to change the default IP
address after your access.
Figure 3. 1 Activation Interface
3. Create a password and input the password into the password field.
STRONG PASSWORD RECOMMENDED– We highly recommend that you create a strong
password of your own choosing (using 8-16 characters, including upper case letters, lower case letters,
numbers, and special characters) in order to increase the security of your product. And we recommend that
you reset your password regularly, especially in the high security system, resetting the password monthly or
weekly can better protect your product.
4. Confirm the password.
5. Click OK to save the password and enter the live view interface.
Page 12
DS-6700HQHI-SATA Series Encoder Quick Start Guide
11
3.2 Setting Admin Password and Modifying
Network Parameters via Client Software
The client software is a versatile video management software for multiple kinds of devices.
Get the client software from the supplied disk or the official website, and install the software according to the
prompts. Follow the steps to activate the camera.
Steps:
1. Run the client software and the control panel of the software pops up, as shown in the figure below.
Figure 3. 2 Main Interface
2. Click the Device Management icon to enter the Device Management interface, as shown in the figure below.
Figure 3. 3 Device Management
Page 13
DS-6700HQHI-SATA Series Encoder Quick Start Guide
12
3. Check the device status from the device list, and select an inactive device.
4. Click the Activate button to pop up the Activation interface.
5. Create a password and input the password in the password field, and confirm the password.
STRONG PASSWORD RECOMMENDED– We highly recommend that you create a strong
password of your own choosing (using 8-16 characters, including upper case letters, lower case letters,
numbers, and special characters) in order to increase the security of your product. And we recommend that
you reset your password regularly, especially in the high security system, resetting the password monthly or
weekly can better protect your product.
Figure 3. 4 Activation Interface
6. Click OK button to start activation.
7. Click the Modify Netinfo button to pop up the Network Parameter Modification interface, as shown in the
figure below.
Figure 3. 5 Modify Network Parameter
Page 14
DS-6700HQHI-SATA Series Encoder Quick Start Guide
13
8. Change the device IP address to the same subnet with your computer by either modifying the IP address
manually or checking the checkbox of Enable DHCP.
9. Input the password to activate your IP address modification.
Page 15
DS-6700HQHI-SATA Series Encoder Quick Start Guide
14
Chapter 4 Access to DS-6700HQHI-SATA
by Web Browser
The DS-6700HQHI-SATA can also be accessed by WEB Browser for configuration and operation. The supported
WEB browsers include: Internet Explorer 6/7/8/9 and above, Firefox 3.5 and above, Chrome 8 and above, Safari
5.0.2 and above.
Open WEB browser, input the IP address of DS-6700HQHI-SATA (e.g., http://192.0.0.64) and then press the
Enter key on PC. The login interface is displayed.
When the HTTPS feature is enabled, the system will use the HTTPS login mode (e.g., https://192.0.0.64) by
default. You can also input http://IP address/index.asp (e.g., http://192.0.0.64/index.asp) if you want to use HTTP
mode to log into the device.
Figure 4. 1 Login Interface
Input the user name and password to log into the system.
In the Login dialog box, if you have entered the wrong password for 7 times for the admin user or 5 times for the
normal user, the current user account will be locked for 60 seconds.
You should download and install the plug-in for the first time to use.
Figure 4. 2 Message from Webpage
Page 16
DS-6700HQHI-SATA Series Encoder Quick Start Guide
15
4.2 Starting Live View
1. In the live view window, select a playing window by clicking the mouse.
2. Double-click a camera from the device list to start the live view.
Figure 4. 3 Live View Interface
3. You can click the button on the toolbar to start the live view of all cameras on the device list.
Refer to the following table for the description of buttons on the live view window:
Icon
Description
Select the split window mode
/
Start/Stop live view
Capture pictures in live view mode
/
Manually start/stop recording
Enable e-PTZ
Previous page
Next page
/
Audio on/off
/
Start/Stop two-way audio
Switch to full-screen live view mode.
Before using two-way audio function or recording with audio, please select the Video Type to Video & Audio
under Remote Configuration > Camera Settings >Video Settings.
4.3 Operating PTZ Control
Before you start:
Page 17
DS-6700HQHI-SATA Series Encoder Quick Start Guide
16
1. Make sure the encoder is connected with the camera/dome which supports PTZ function. Connect the R+ and
R- terminals of the pan/tilt unit or speed dome to RS-485 T+ and RS-485 T- terminals of the
DS-6700HQHI-SATA respectively.
2. The baud rate, PTZ control and address configured in the RS-485 Settings interface (Remote
Configuration > Serial Port Settings > 485 Serial Port) must be the same with the parameters of the
connected pan/tilt unit or speed dome.
Operating PTZ Control
In live view mode, you can use the PTZ control buttons to realize pan/tilt/zoom control of the camera lens.
There will be 8 directional buttons (up, down, left, right, upper left, upper right, bottom left, bottom right) on the
display window when the mouse is located in the relative positions.
Click on the directional buttons to control the pan/tilt movement.
Figure 4. 4 PTZ
Click the zoom/iris/focus buttons to realize lens control.
Refer to the following table for description of PTZ control buttons:
Table 4. 1 Button Description
Button
Description
Zoom in/out
Focus near/far
Iris open/close
Light on/off
Wiper on/off
Adjust speed of pan/tilt movement
(level 1to 7 is selectable)
4.4 Recording
Before you start
Make sure the Encoder is connected with HDD (for DS-6700HQHI-SATA) or network disk, and the HDD or
network disk has been initialized for the first time to use.
Two recording types can be configured: Manual and Scheduled. The following section introduces the
configuration of scheduled recording.
Page 18
DS-6700HQHI-SATA Series Encoder Quick Start Guide
17
Steps:
1. Click Remote Configuration > Camera Settings > Schedule Settings to enter record schedule settings
interface.
2. Select the camera to configure the record schedule.
3. Check the checkbox of Enable Record Schedule to enable recording schedule.
Figure 4. 5 Schedule Settings Interface
4. Click Edit to enter the Edit Schedule interface.
5. Choose the day in a week to configure scheduled recording.
Figure 4. 6 Edit Schedule
1) Configure All Day or Customized Period Record:
If you want to configure the all-day recording, please check the All Day checkbox.
If you want to record in different time sections, check the Customize checkbox. Set the Start Time and
End Time of each period.
Page 19
DS-6700HQHI-SATA Series Encoder Quick Start Guide
18
The time of each period can’t be overlapped. Up to 8 periods can be configured.
2) Select a Record Type. The record type can be Normal, Motion, Alarm, Motion & Alarm, and Motion |
Alarm.
3) Check the checkbox of Select All and click Copy to copy settings of this day to the whole week. You can
also check any of the checkboxes before the date and click Copy.
4) Click OK to save the settings and exit the Edit Schedule interface.
6. On the Schedule Settings interface, click Advanced to configure advanced record parameters.
7. Click Save to validate the above settings.
4.5 Playback
Purpose:
The recorded video files can be remotely played back through the WEB browser.
Steps:
1. Click Playback on the menu bar to enter playback interface:
Figure 4. 7 Playback Interface
2. Click the camera from the device list for playback.
3. Select the date from the calendar and click Search.
Figure 4. 8 Calendar
Page 20
DS-6700HQHI-SATA Series Encoder Quick Start Guide
19
4. Click the button to play the video file searched on the current date.
Figure 4. 9 Playback Interface
5. Use the buttons on the toolbar to operate in playback mode
Figure 4. 10 Toolbar
Table 4. 2 Button Description
Button
Operation
Button
Operation
Select window-division mode
Reverse
/
Play/Pause
Stop playing
Slow forward
Fast forward
Play by single frame
Stop all channels from playing
Capture pictures in playback mode
Download video files
/
Start/Stop clipping video files
/
Audio on/off
Switch to full-screen live view mode.
6. You can drag the progress bar with the mouse to locate the exact playback point, or input the time and click
button to locate the playback point.
Figure 4. 11 Playback Point
Figure 4. 12 Progress Bar
The color of the video on the progress bar stands for the different video types.
Page 21
DS-6700HQHI-SATA Series Encoder Quick Start Guide
20
Figure 4. 13 Color Bar
4.6 Log
Purpose:
The operation, alarm, exception and information of the device can be stored in log files, which can be viewed and
exported at any time.
Before you start
The Log function can be realized only when the Encoder is connected with HDD (for DS-6700HQHI-SATA) or
network disk. And make sure the HDD or network disk has been initialized for the first time to use.
Steps:
1. Click Log on the menu bar to enter the Log interface.
2. Set the log search conditions to refine your search, including the Major Type, Minor Type, Start Time and
End Time.
3. Click the Search button to start searching log files.
4. The matched log files will be displayed on the list shown below.
Up to 100 log files can be displayed each time.
Figure 4. 14 Log Interface
5. You can click the button to save the searched log files to local directory.
0102041050505
Page 22
DS-6700HQHI-SATA Series Encoder Quick Start Guide
21
Loading...