Hetronic RXMFSESCANHS1 User Manual
User’s Manual
RX-MFS-ESCAN-HS1
1. DESCRIPTION
RX-MFS-ESCAN-HS1 is a MFS 2.4GHz receiver with 2 CAN Interfaces, 2 independent E-Stop Relay Outputs, 2 Application Relay Outputs, 4
optional 0~10V, 0~20mA analog or 0~30V digital inputs, a USB and an optional RS232 interface. It shall be equipped with RTC and SD card
for data logging capability. It is designed for applications using CAN bus topology to integrate a number of devices and operating on 12 or 24V
battery.
The function of this device is to provide a bidirectional RF control to CAN bridge in a machine control application, along with standard Main
Contact safety functionality. Receiver and CAN settings shall be H-Link configurable and are saved to an on-board EEPROM.
RX-MFS-ESCAN-HS1 uses the MFS 2.4GHz communication protocol. The decoder receives control packets at a 1%-10% duty cycle to the
receiver and transmits one feedback packet for every control packet. The feedback packets are sent on one of the sixteen IEEE 802.15.4 ISMband channels, ranging from 2.405-2.480GHz. The channels and duty cycle are configured with the H-Link software. The packets are DSSS OQPSK modulated using an on-board surface-mount transceiver and then amplified through an on-board surface-mount bi-directional RF Front
End. The RF signal goes through a surface-mounted SMA connector, through a 50-ohm coaxial cable to an external antenna for
transmission/reception. The external antenna is a Hetronic Gainflex 2.4GHz antenna (Hetronic Part Number 56506605) with a nominal gain of
3dB.
The antenna is Model: 56506605 – Manufacturer: APEX - Gainflex Type GK 442TF R Half wave flexible dipole – maximum power
10W – TNC Plug Reverse Polarity
Antenna Gain: 3 dB
Note: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
Note: The RX-MFS-ESCAN-HS1 is shipped with the FCC/IC ID label attached. The FCC/IC ID label must not be
removed. See Figure 3 for additional labeling information.
FCC ID Number: LW9-RXMFSCANHS1
IC ID Number: 2119B-RXMFSCANHS1
RSS-Gen license-exempt notice:
“This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.”
RSS-Gen antenna notice 1:
“Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference
to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type
d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité
nécessaire à l'établissement d'une communication satisfaisante. ”
Loading...