Hanna Instruments HI 9063 User Manual
Instruction Manual
HI 9063
Portable Waterproof
Microprocessor
K-Type Thermocouple
Thermometer
www.hannainst.com
Dear Customer,
Thank you for choosing a Hanna product.
This manual will provide you with the necessary information
for correct operation. Please read it carefully before using the
meter. If you need additional technical information, do not
hesitate to e-mail us at tech@hannainst.com.
This instrument is in compliance with the directives.
PRELIMINARY EXAMINATION
Remove the instrument from the packing material and examine it carefully to make sure that no damage has occurred
during shipping. If there is any noticeable damage, notify
your Dealer or the nearest Hanna Office.
Note: Save all packing materials until you are sure that the
instrument functions correctly. Any defective item must
be returned in the original packaging together with
the supplied accessories.
FUNCTIONAL DESCRIPTION SPECIFICATIONS
Range (*)
Resolution
Accuracy
Typical EMC
Deviation
Battery Type
Life
Probe
Environment
Dimensions
Weight
(*) Range may be limited by probe.
0.1°C (up to 199.9°C) / 1°C (outside)
0.1°F (up to 399.9°F) / 1°F (outside)
approx. 2000 hours of continuous use
K-type thermocouple (see “Accessories”)
-10 to 50ºC (14 to 122ºF); RH 100%
-50.0 to 1350°C
-58.0 to 2462°F
±0.2% F.S.
for 1 year, excluding probe error
±3°C / ±6°F
(with HI 766 probes)
4 x 1.5V AA (IEC LR6)
196 x 80 x 60 mm (7.7x3.1x2.4")
500 g (1.1 lb.)
WARRANTY
All Hanna Instruments meters are warranted for two years against defects in workmanship and materials when used for their intended purpose
and maintained according to instructions. Sensors and probes are war-
ranted for a period of six months.
This warranty is limited to repair or replacement free of charge.
Damages due to accidents, misuse, tampering or lack of prescribed maintenance are not covered.
If service is required, contact the dealer from whom you purchased the instrument. If under warranty, report the model number, date of purchase, serial
number and the nature of the failure.
First obtain a Returned Goods Authorization number from the Customer Service department, then return the instrument with the Authorization # included
along with shipment costs prepaid. If the repair is not covered by the warranty, you will be notified of the charges.
When shipping any instrument, make sure it is properly packaged for complete protection.
Hanna Instruments reserves the right to modify the design, construction and
appearance of its products without advance notice.
GENERAL DESCRIPTION
HI 9063 is a waterproof, microprocessor-based, K-type thermocouple thermometer, which provides very accurate
measurements in a wide range of temperatures.
The meter is also provided with low battery detection and
BEPS (Battery Error Preventing System), which turns the unit
off when the batteries are discharged avoiding erroneous
readings caused by low battery level.
HI 9063 features include autoranging capability, dual-level
LCD for simultaneously displaying of maximum and minimum
measured temperatures, °C/°F selection button and hold
function.
The meter is supplied complete with four 1.5V AA batteries
and instruction manual.
1. Temperature probe connector
2. Liquid Crystal Display
3. ON/OFF key
4. Measuring unit selection key
5. HOLD key
6. HI/LO values reset key
1. Current temperature value
2. HOLD indicator
3. Low battery indicator
4. Minimum temperature value
5. Maximum temperature value
6. K-type probe indicator
7. Measuring unit, °C or °F
FACTORY RECALIBRATION
All Hanna Instruments thermometers have been accurately
pre-calibrated at the factory.
It is generally recommended to have all thermometers
recalibrated at least once a year.
For an accurate annual recalibration, contact your nearest
Hanna Service Center.
OPERATIONAL GUIDE
INITIAL PREPARATION
Each meter is supplied complete with
batteries.
Remove the back cover, unwrap the
batteries and install them while paying attention to their polarity.
Connect a K-type thermocouple probe to
the meter.
To switch on, press the ON/OFF key on
the front of the meter.
If the meter does not come on, make
sure that the batteries are correctly
installed.
The thermometer will carry out a self diagnostic test routine,
the LCD will show all segments for a few seconds (or as long as
ON/OFF is held), followed by the percentage indication of the remaining
battery life.
The thermometer then enters normal measurement mode.
If a temperature probe is plugged in, the meter displays the
measured temperature.
If no probe is plugged in, or if reading
is over-range, the display shows flashing dashes.
If a measurement is slightly over the range of the meter
specifications, the display flashes the closest full-scale value.
To switch the thermometer OFF, press the ON/OFF key.
MEASURING SCALE (°C/°F)
The instrument is factory set to the °C scale, but measurements can
be performed in either the Celsius or Fahrenheit scale.
Press the °C/°F button to select the desired
scale.
HOLD MODE
The HOLD function is activated by pressing the HOLD key.
The measured temperature is held on the
display until HOLD is pressed again.
The "H" tag blinks on the display to
indicate the HOLD mode.
Note: Although the display is frozen, internally the meter
continues measuring and updating Hi and Lo values.
HIGH/LOW TEMPERATURES
The maximum and minimum temperatures are continuously monitored and
displayed in the lower portion of the
LCD.
Note: When reading goes over-range, the Hi and Lo values
display dashes until cleared.
CLEAR FUNCTION
Upon pressing the CLEAR key, the
current reading is assigned to the
highest and lowest temperature values. The High/Low values may be
cleared at any time during measurement.
BATTERY REPLACEMENT
The instrument is powered by four 1.5 V alkaline batteries
and is provided with the Battery Error Prevention System
(BEPS), which turns the unit off when a low battery signal is
detected.
When the remaining battery level is
less than 10%, a warning symbol
blinks on the display to indicate a low
battery condition.
It is recommended to replace the batteries as soon as the low
battery condition is detected.
Battery replacement must only take place in a nonhazardous
area using four 1.5V alkaline batteries.
In order to replace rundown batteries, simply remove the two
screws on the rear cover of the instrument and replace the
four batteries with new ones paying attention to the correct
polarity.
Reattach the cover and tighten the two screws.
ACCESSORIES
K-TYPE THERMOCOUPLE PROBES
with integral handle, 1 m (3.3’) cable & mini-connector:
HI 766A Roller surface probe, max 320°C/600°F
HI 766B Surface probe, max 650°C/1200°F
HI 766B1 90º Surface probe, max 450°C/840°F
HI 766B2 Spring-loaded, surface probe, max
900°C/1650°F
HI 766B3 Spring-loaded, small surface probe with
insulated shaft, max 200°C/390°F
HI 766C Penetration probe, max 900°C/1650°F
HI 766C1 Ultra-fast Penetration probe, max 300°C/
570°F
HI 766D Air probe, max 300°C/570°F
HI 766E1 General purpose probe, max 900°C/1650°F
HI 766E2 General purpose probe, max 900°C/1650°F
HI 766F High temperature, flexible wire probe
without handle, max 1100°C/2000°F
HI 766F1 Flexible wire probe without handle, max
480°C/ 900°F
HI 766TR1 Penetration probe, max 250°C/482°F
HI 766TR2 Penetration long probe, max 250°C/482°F
HI 766TV1 Pipe clamp probe, max 200°C/390°F
with detachable handle & mini-connector (to be used
in conjunction with the HI 766HD probe handle):
HI 766PA Roller surface probe, max 320°C/600°F
HI 766PB Surface probe, max 650°C/1200°F
HI 766PC Penetration probe, max 900°C/1650°F
HI 766PD Air probe, max 300°C/570°F
HI 766PE1 General purpose probe, max 900°C/1650°F
HI 766PE2 General purpose probe, max 900°C/1650°F
grill surface probe:
HI 766B4 Grill surface probe with 70 cm (27.6’’)
cable (protected with stainless steel jacket),
max 250°C/482°F
HI 7664B4S Spare stainless steel sensor for HI766B4 probe
OTHER ACCESSORIES
HI 710021 Spare protective case
HI 721317 Rugged carrying case
HI 766EX Extension cable for K-type probes
HI 766HD Rugged thermocouple probe handle with
1m (3.3') cable fitted with mini-connector
CE DECLARATION OF CONFORMITY
Recommendations for Users
Before using this product, make sure that it is entirely suitable for the environment in which it is used.
Operation of this instrument in residential areas could cause unacceptable interference to radio and
TV equipment, requiring the operator to take all necessary steps to correct interference.
Any variation introduced by the user to the supplied equipment may degrade the instruments' EMC
performance.
To avoid electrical shock, do not use these instruments when voltage at the measurement surface
exceeds 24 Vac or 60 Vdc.
To avoid damage or burns, do not perform any measurement in microwave ovens.
IST9063R1 06/05
Loading...