Hanna Instruments HI 9056 User Manual

Instruction Manual
HI 9056
HI 9057
Portable Microprocessor
Thermocouple
Thermometers
Manufacturers since 1978
These Instruments are in
Dear Customer, Thank you for choosing a Hanna Product.
Please read this instruction manual carefully before using the instrument.
This manual will provide you with the neces­sary information for a correct use of the instrument, as well as a precise idea of its versatility.
If you need more technical information, do not hesitate to e-mail us at tech@hannainst.com.
These instruments are in compliance with directives.
TABLE OF CONTENTS
Preliminary Examination ............................ 3
General Description ................................... 3
PRELIMINARY EXAMINATION
Remove the instrument from the packing ma­terial and examine it carefully to make sure that no damage has occurred during ship­ping. If there is any damage, notify your Dealer or the nearest Hanna Customer Ser­vice Center.
Each meter comes supplied complete with a 9V battery and instruction manual:
Note: Save all packing material until you are
sure that the instrument functions cor­rectly. All defective item must be returned in the original packing with the supplied accessories.
GENERAL DESCRIPTION
Functional Description &
Specifications of HI 9056 .......................... 5
Functional Description &
Specifications of HI 9057 .......................... 6
Operational Guide ...................................... 7
Display Codes Guide ............................... 11
Calibration ................................................ 12
Battery Replacement ............................... 12
Shockproof Rubber Boots ........................ 13
Accessories .............................................. 14
Warranty .................................................. 18
CE Declaration of Conformity ................. 19
HI 9056 performs temperature measure­ments using interchangeable K-type ther­mocouple probes.
HI 9057 performs temperature measure­ments with different types of thermocouples (K - J - T). This meter is equipped with a key that switches range from K-type to J-type or T-type thermocouples.
The non-linearity of the temperature probe is linearized by the built-in microprocessor, in order to achieve a high degree of accu­racy and resolution. Also the HI9056 accu­rately compensates for temperature drifts in the measurement circuit and the reference junction.
HI 9056 has two built-in K-type probe con­nectors. By simply pressing a button, the meter switches between the two readings on
the display. A "T" button will display the
difference between the two probe readings.
32
Standard features include:
• Interchangeable probes
• Clear Liquid Crystal Display
• Two year Warranty
• Possibility of switching between the Cen­tigrade and the Fahrenheit scale (for HI 9057 only)
• HOLD function that freezes the reading on the display (for HI 9057 only)
• HI-LO memory recall function (for HI 9057 only)
• Low battery detection.
All these functions are easily accessible through the keypad.
Self-explanatory symbols are used to re­mind the user of the operating mode or condition.
Hanna manufactures several K-type ther­mocouple probes for different applications. See pages 14-17 for more details.
FUNCTIONAL DESCRIPTION AND
SPECIFICATIONS FOR HI 9056
1. Liquid Crystal Display
2. ON/OFF Key
3. Reading Memory/Hold Key
4. Measurement Resolution Key (0.1 or 1)
5. Input Probe Selection Key (T1 or T2)
6. Temperatures Difference Key
7. Memory Recalling Key.
Specifications
Range -200.0 to 1370°C
Resolution 0.1°C (-200.0 to 999.9°C)
1°C (1000 to 1370°C)
Accuracy ±0.2% F.S. (@20°C / 68°F) for one year, excluding probe error
Typical EMC ±3°C Deviation ±6°F
Probe K-thermocouple (optional)
(see pages 14-17)
Battery 9V/300 hours of continuous use
Environment 0 to 50°C (32 to 122°F); 95% RH
Dimensions 180 x 83 x 40 mm (7.1 x 3.3 x 1.6")
Weight 350 g (12.4 oz.)
54
FUNCTIONAL DESCRIPTION AND
SPECIFICATIONS OF HI 9057
OPERATIONAL GUIDE
INITIAL PREPARATION
Remove the battery cover on the rear of your thermom­eter, unwrap the battery and connect it to the clip. Insert the battery into the compart­ment and replace the cover.
1. Liquid Crystal Display
2. ON/OFF Key
3. Reading Memory/Hold Key
4. Thermocouple Type Selection Key (K or J or T)
5. Minimum Temperature Recalling Key
6. Maximum Temperature Recalling Key
7. Measuring Scale key (°C or °F).
Specifications
Range K -200.0 to 1370°C / -300.0 to 2500°F
J -200.0 to 900.0°C / -300.0 to 1650°F
T -200.0 to 400.0°C / -300.0 to 750.0°F
Resolution 0.1°C (up to 999.9°C) 0.1°F(up to 999.9°F)
1°C (over 1000°C) 1°F (over 1000°F)
Accuracy K= ±0.2% F.S. (@20°C / 68°F) J = ±0.2% F.S.
T = ±0.5% F.S.
for one year, excluding probe error
Typical EMC ±3°C Deviation ±6°F Probe K, J and T thermocouple (optional)
(for K-thermocouple see pages 14-17)
Battery 9V/300 hours of continuous use Environment 0 to 50°C (32 to 122°F); 95% RH Dimensions 180 x 83 x 40 mm (7.1 x 3.3 x 1.6")
Weight 350 g (12.4 oz.)
To switch on, press ON/OFF on the front of the unit.
ON
OFF
The thermometer performs a self diagnostic test. The LCD dispalys all the segments at once, to ensure none are
BAT HOLD K J T
ºC ºF HI LO
missing.
After the test, the thermometer will switch to the measurement mode.
If a temperature probe is plugged in, the unit will display the temperature.
If the probe is not plugged in, the display will show "----".
To switch your thermometer off, press ON/ OFF again.
MEASURING SCALE (°C/°F) (HI 9057 only)
When the meter is turned on, it automati­cally defaults to the °C scale. Measurements can be performed on either the Centigrade or the Fahrenheit scale.
76
To change the scale, press °C/°F once.
°C °F
°F
Check the highest or lowest measured tem­perature by pressing the respective HI or LO key. The appropriate display indicator, "HI" or "LO", will light up together with the value retrieved from memory.
MEASUREMENT RESOLUTION
When switched on, HI 9056
°C
and HI 9057 default to a 0.1 digit resolution (see specifi­cations).
These instruments automatically change the resolution to 1 degree when the measured temperature is higher than 999.9°C.
In HI 9056, when the tem- perature is lower than
999.9°C it is possible to change the resolution by pressing the 0.1/1 key.
HOLD MODE (HI 9057 only)
The reading hold function is activated by the HOLD key.
To freeze the measured temperature on the display, press and hold the HOLD key. "HOLD" is displayed when this key is pressed.
°C
°C
HI
LO
Release the key to resume normal opera­tion.
CLEAR HI-LO FUNCTION (HI 9057 only)
By pressing HI and LO simultaneously the present measurement reading is assigned in memory as the highest and lowest tempera­ture reading, i.e. both "HI" and "LO" will have equal temperature readings.
HOLD
As soon as the HOLD key is released, the meter returns to normal operational mode.
HI-LO FUNCTION (HI 9057 only)
Maximum and minimum temperatures are monitored throughout a continuous measur­ing process.
The values may be recalled or cleared at any time during the measurement.
MEMORY FUNCTION (HI 9056 only)
The memory & hold function is activated by MEM HOLD. The measured temperature is stored in memory and frozen on the display when this function key is pressed and held.
MEM
HOLD
98
The memory value will be overridden each time the memory & hold function is acti­vated. A blinking "MEM" on display indi­cates the operating mode.
Press and hold MR to recall previously stored temperature reading. In this mode of opera­tion, the display indicator "MEM" is shown.
TEMPERATURE DIFFERENCE (HI 9056 only)
The difference between the temperature measured by the two probes can be dis-
played by simply pressing T. A "" will
appear on the left-hand of the display to indicate this function.
MEM
If no data is found, "----" will be displayed.
THERMOCOUPLE TYPE SELECTION (HI 9057 only)
By pressing KJT the user is allowed to set the thermometer according to the connected thermocouple type, and the related symbol will be displayed, i.e.:
K for K-Type, J for J-Type, T for T-Type.
KTJ
PROBE INPUT SELECTION (HI 9056 only)
When switched on, the in­strument automatically shows the temperature measured by
K 1
Probe 1 and a "K1" appears on the LCD display.
To view the input temperature of Probe 2, press T1/T2 and "K2" will be displayed.
K 2
LOW BATTERY DETECTION
To save battery life, HI 9056 and HI 9057 will switch off after 5 minutes.
When the battery is low the user is prompted by the word "BAT" to substitute the bat­tery (see page 12).
DISPLAY CODES GUIDE
Display Description
---- The probe is not connected to the instrument
BAT Weak battery, needs to be replaced
HI 9056:
HOLD Freezes current reading on display and stores MEM the reading into memory
MEM Indicates the value of the temperature stored
K1 or K2 Temperature at probe 1 or 2 respectively
∆∆
Difference between temperatures at the two
∆∆
HI 9057:
°C The instrument is reading in the Centigrade
°F The instrument is reading in the Fahrenheit
HI Displays the highest measured temperature
LO Displays the lowest measured temperature
HOLD Freezes current reading on display
K,J or T Thermocouple probe type in use
or the reading is out of range
into memory
probes
scale
scale
1110
CALIBRATION
SHOCKPROOF RUBBER BOOTS
All Hanna Instruments thermometers have been accurately pre-calibrated at the fac­tory.
It is generally recommended to have all thermometers recalibrated at least once a year.
For an accurate annual recalibration, con­tact your nearest Hanna Service Center.
BATTERY REPLACEMENT
When the battery is low the user is warned by the "BAT" indication on the instrument's display. Re­place the battery immedi­ately.
Battery should only be replaced in a safe area using the battery type specified in this instruction manual (see page 17).
Remove the battery com­partment cover on the rear of the meter and replace the 9V battery with a new one. Make sure the battery contact is tight before re­placing the cover.
The meter may turn on au­tomatically when a new bat­tery is connected. You can turn it off by pressing ON/OFF.
These rubber boots are specially made to prolong the life of your instruments and to prevent damage due to accidental falls.
They and are available in two different col­ors:
HI 710009 = blue colored
HI 710010 = orange colored
Select the proper color according to your preference.
1312
ACCESSORIES
K-Type Thermocouple Probes with detachable handle & mini-connec­tor
(to be plugged into HI 766HD probe handle):
HI 766PA Roller surface probe, max 320°C/600°F
100mm
4"
280mm
11"
7.8"
HI 766PB Surface probe, max 650°C/1200°F
200mm
7.9"
HI 766PC Penetration probe, max 900°C/1650°F
155mm
6.1"
3mm
0.12"
HI 766PE1 General use probe, max 900°C/1650°F
155mm
6.1"
3mm
0.12"
HI 766PE2 General use probe, max 900°C/1650°F
200mm
7.8"
HI 766HD Rugged thermocouple probe handle
with 1 m (3.3' ) cable fitted with a mini­connector
with integral handle, 1 m cable & mini­connector:
HI 766A Roller surface probe, max 320°C/600°F
5mm
0.20"
100mm
4"
HI 766PD Air probe, max 300°C/570°F
250mm
9.8"
3mm
0.12"
280mm
11"
420mm
13.3"
16.5"
HI 766B Surface probe, max 650°C/1200°F
400mm
15.7"
260mm
10.2"
1514
HI 766B1 90° surface probe, max 450°C/840°F
300mm
11.8"
30mm
1.2"
HI 766E2 General use probe, max 900°C/1650°F
360mm
13.8" 220mm
8.5"
5mm
0.2"
HI 766B2 Surface probe, max 900°C/1650°F
8mm
0.3"
130mm
5.1"
HI 766B3 Small surface probe with insulated shaft,
max 200°C/390°F
5mm
0.2"
130mm
5.1"
HI 766C Penetration probe, max 900°C/1650°F
260mm
10.3" 120mm
4.8"
3mm
0.12"
HI 766D Air probe, max 300°C/570°F
385mm
15.2" 245mm
9.6"
3mm
0.12"
HI 766F High temperature wire probe without
handle, max 1100°C/2000°F
255mm
10"
1.5mm
0.06"
HI 766F1 Flexible probe without handle, max
480°C/900°F
2mm
1m
3.3’
0.08"
HI 766TV1 Pipe clamp probe, max 200°C/390°F
35mm
Max.
1.4"
HI 766E1 General use probe, max 900°C/1650°F
260mm
10.2"
120mm
4.7"
3mm
0.12"
Other accessories:
HI 710002 Soft carrying case
HI 710009 Blue rubber boot
HI 710010 Orange rubber boot
1716
WARRANTY
All Hanna Instruments meters are guaranteed for two years against defects in workmanship and materials when used for their intended purpose and maintained according to instruc­tions. The electrodes and the probes are guaranteed for a period of six months. This warranty is limited to repair or replacement free of charge.
Damage due to accident, misuse, tampering or lack of prescribed maintenance are not covered.
If service is required, contact the dealer from whom you purchased the instrument. If under warranty, report the model number, date of purchase, serial number and the nature of the failure. If the repair is not covered by the warranty, you will be notified of the charges incurred. If the instrument is to be returned to Hanna Instruments, first obtain a Returned Goods Authorization number from the Cus­tomer Service department and then send it with shipping costs prepaid. When shipping any instrument, make sure it is properly pack­aged for complete protection.
To validate your warranty, fill out and return the enclosed warranty card within 14 days from the date of purchase.
All rights are reserved. Reproduction in whole or in part is prohibited without the written consent of the copyright owner, Hanna Instruments Inc., 584 Park East Drive, Woonsocket, Rhode Island, 02895 , USA.
Hanna Instruments reserves the right to modify the design, construction and ap­pearance of its products without advance notice.
CE DECLARATION OF CONFORMITY
Recommendations for Users
Before using these products, make sure that they are entirely suitable for the environment in which they are used.
Operation of these instruments in residential areas could cause unacceptable interferences to radio and TV equipment, requiring the operator to take all neces­sary steps to correct interferences.
Any variation introduced by the user to the supplied equipment may degrade the instrument's EMC performance.
In particular cases the instruments could turn off. In such cases they can be turned on by pressing the ON/OFF key.
To avoid electrical shock, do not use these instruments when voltages at the measurement surface exceed 24VAC or 60 VDC.
To avoid damages or burns, do not perform any measurement in microwave ovens.
1918
HANNA LITERATUREHANNA LITERATURE
HANNA LITERATURE
HANNA LITERATUREHANNA LITERATURE
Hanna publishes a wide range of catalogs and handbooks for an equally wide range of applications. The reference literature currently covers areas such as:
• Water Treatment
• Process
• Swimming Pools
• Agriculture
• Food
• Laboratory
• Thermometry
and many others. New reference material is constantly being added to the library.
For these and other catalogs, handbooks and leaflets, contact your dealer or the Hanna Customer Service Center nearest to you. To find the Hanna Office in your vicinity, check our home page at www.hannainst.com.
http://www.hannainst.com
MAN9056R2 04/00
Loading...