Grundig LXW 82-8625 IDTV, LXW 94-8625, LXW 94-8625 IDTV User Manual

COLOR TELEVISION

Xentia 32 LXW 82-8625 IDTV

Xentia 37 LXW 94-8625 IDTV

Installation 3 Remote control handset 4-5

Controls 4 Battery installation 5

Controls of

Front panel 6

Connections of

Back panel 7

Connection to

External equipment 8-12

Basic operation

On and Off 13 Programme selection 13 Volume adjustment 13 On screen language selection 13

On screen menus

Menu selection 14

Setting up TV stations 15-23

Sound adjustment 15-18 Picture adjustment 19-21 Child lock 22 Timer 23-25

DTV option Menu (in digital mode only) 26-29 Preset list Menu 30-32

Installation Menu 33 Other Menu 34 Connection of PC 35 PIP (Picture-In-Picture) Feature 36-37

Watching PIP 36 PIP Audio input 36 Moving the PIP 37 Sub picture size 37 Programme scan 37

Information Menu (In Digital mode only) 38 Teletext 39-40 Displayable Monitor Specification 41 Troubleshooting

Check list 43

Contents

Power

This set operates on an AC mains supply, the voltage is as indicated on the label on the back cover. Never apply DC power to the set. In the event of thunderstorms or powercuts, please pull out the aerial and mains plugs.

Warning

To prevent fire or shock hazard, do not expose the set to rain or moisture. Do not rub or strike the Active Matrix LCD with anything hard as this may scratch, mar, or damage the Active Matrix LCD permanently.

Service

Never remove the back cover of the set as this can expose you to very high voltage and other hazards. If the set does not operate properly, unplug it and call your dealer.

Aerial

Connect the aerial cable to the socket marked +75 on

the back cover. For the best reception an outdoor aerial should be used.

Location

Position your set so that no bright light or sunlight falls directly onto the screen. Care should be taken not to expose the set to any unnecessary vibration, moisture, dust or heat. Also ensure that the set is placed in a position to allow a free flow of air. Do not cover the ventilation openings on the back cover.

Cleaning

Unplug the set before cleaning the face of the LCD Screen. Dust the set by wiping the screen and the cabinet with a soft, clean cloth. If the screen requires additional cleaning, use a clean, damp cloth. Do not use liquid cleaners or aerosol cleaners.

Installation

To preserve the Environment, do not rubbish.

- All the functions can be controlled with the remote control handset.

- Some functions can also be adjusted with the buttons on the front panel of the set.

Remote control handset

Controls

Before you use the remote control handset, please install the batteries.

NUMBER BUTTONS

i BUTTON

selects a menu.

D/ E

(Programme Up/Down)

selects a programme or a menu item.

switches the set on from standby.

F / G (Volume Up/Down)

adjusts the volume.

adjusts menu settings.

accepts your selection or displays the

current mode.

TELETEXT BUTTONS

These buttons are used for teletext.

For further details, see the ‘Teletext’ section.

SCAN

switches on the programme scan mode

through 4/16 sub pictures.

Display the TV Guide in digital mode.

P AP (Picture And Picture)

selects the double window function.

PSM (Picture Status Memory)

recalls your preferred picture setting.

SIZE

adjusts the sub picture size.

VCR, SAT, DVD

Switches to operating a GRUNDIG video

recorder, a GRUNDIG satellite receiver

or a GRUNDIG DVD player.

Keep the appropriate button VCR, SAT, DVD

pressed down. Then press the appropri-

ate button

Note : The functions available depend on the

model of the device you are using.

Just try it out.

POWER

switches the set On from standby or Off to standby.

PIP

Switches the sub picture On or Off.

ARC

select your desired picture format. page stop in teletext mode.

SLEEP

sets the sleep timer. select a sub page number in teletext mode.

MUTE

switches the sound On or Off.

Zap function

returns to the previously viewed programme.

AV INPUT

Select DTV, TV, AV1, AV2, S-VIDEO, COMPONENT, PC-RGB, HDMI mode. switches the set on from standby.

PIP POSITION

relocates the sub picture in clockwise direction.

SSM (Sound Status Memory)

recalls your preferred sound setting.

STILL

freezes motion of the sub picture.

TIME

Display the time at the screen. Selects a favourite programme add and delete in digital mode.

- COLOURED BUTTONS

These buttons are used for teletext (only TELETEXT models) or programme edit.

PIP

P+

P-

SCAN

SIZE

PAP

POS

VCR

SAT

DVD

/ TV-G

TXT

/ Add Del

Tele Pilot 160A

Remote control handset

Battery installation

- Your remote control handset is powered by two AA type batteries.

- To insert batteries, turn the remote control handset over and remove the battery cover.

- Put the two batteries into the compartment observing battery polarity.

- Replace the cover.

To avoid damage from possible battery leakage, remove the batteries if you do not plan to use the remote control handset for an extended period time. Do not use batteries of differing age or type. Always discard of batteries safely.

Controls of

Front panel

1. MAIN POWER (I yy )

switches the set On or Off.

D / E

(Programme Up/Down)

selects a programme or a menu item. switches the set On from standby.

3. F / G (Volume Down/Up)

adjusts the volume. adjusts menu settings.

4. MENU

selects a menu.

5. TV/AV

selects DTV, TV, AV 1 , AV 2 , S-VIDEO, COMPO-

NENT

, PC-RGB, HDMI mode.

6. POWER (rr)

switches the set On from standby or On to standby.

7. POWER/STANDBY INDICATOR (rr)

illuminates red in standby mode. illuminates green when the set is switched On.

8. REMOTE CONTROL SENSOR

TV/ATV/AV

MENU MENUP

TV/ATV/AV

MENU MENU

7, 8

- Shown is a simplified representation of the set.

- Here shown may be somewhat different from your set.

- This manual explains the features available on the Xentia series.

Connections of

Back panel

1. HDMI INPUT / RGB INPUT / AUDIO INPUT SOCKETS

Connect the set output socket of the PERSONAL COMPUTER to this socket.

2. AUDIO INPUT / COMPONENT INPUT (480i / 576i / 480p / 576p / 720p / 1080i) SOCKETS

3. AUDIO/VIDEO SOCKET

Connect the audio/video out sockets of the VCR to AV

sockets of the set.

4. S-VIDEO INPUT

connect video out from an S-VIDEO VCR to the SVIDEO input.

5. SERVICE SOCKET

6. AERIAL SOCKET

7. Digital Audio (OPTICAL)

Connect digital audio from various types of equipment.

Note : In standby mode, these ports will not work.

8. POWER CORD SOCKET

This set operates on an AC power. The voltage is indicated on the Specifications page. Never attempt to operate the set on DC power.

RGB INPUTRGB INPUT

AUDIO INPUTAUDIO INPUT

SERSERVICEVICE OPTICALOPTICAL

AUDIO INPUTAUDIO INPUT

AUDIOAUDIO

R L

COMPONENT INPUT (480i/480p/720p/1080i)

Y PbP

S-VIDEOS-VIDEO

ANTANT. IN. IN

AC INPUTAC INPUT

HDMI INPUTHDMI INPUT

AV1V1

VIDEOVIDEO

AUDIOAUDIO

AV2V2

VIDEOVIDEO

AUDIOAUDIO

1 2 3 4 5 6 7 8

Connection to

External equipment

- You can connect additional equipment, such as VCRs, camcorders etc. to your set. However please check with your manufacturers instruction books for specific information. Make sure all connections are made with both your set and additional appliance unplugged from the mains to avoid damaging your equipment. Here shown may be somewhat different from your set.

Connect the RF out socket of the VCR to the aerial socket on the back of the set.

Connect the aerial cable to the RF aerial in socket of the VCR.

Store the VCR channel on a desired programme number using the ‘Manual programme tuning’ sec- tion.

Select the programme number where the VCR channel is stored.

Press the PLAY button on the VCR.

Connect to Aerial socket

- If you connect an S-VIDEO VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input.

- To avoid picture noise (interference), leave an adequate dis-

tance between the VCR and set.

Use the INPUT SELECT button on the remote control to select

AV 1 or AV 2 .

(If connected to S-VIDEO, select the S-Video external input source.)

Insert a video tape into the VCR and press the PLAY button on the

VCR. (See VCR owner’s manual)

Watching VCR

SERVICE OPTICAL

S-VIDEOS-VIDEO

ANTANT. IN. IN

AC INPUTAC INPUT

VCR

SERVICE OPTICAL

S-VIDEOS-VIDEO

ANTANT. IN. IN

AV1V1

VIDEOVIDEO

AUDIOAUDIO

AV2V2

VIDEOVIDEO

AUDIOAUDIO

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

< Back panel of the set >

< Back panel of VCR >

Connection to

External equipment

- After subscribing for a local cable TV station and installing a converter you can watch cable TV.

- For further information of cable TV, contact the local cable TV station.

In using connection 1

Select programme number in programme switch of cable box.

Match the set programme with selected programme of cable box.

Select your desired programme with the remote control for cable box.

In using connection 2 Use the INPUT SELECT button on the remote control and select

AV 1 or AV 2 .

Tune to cable service provided channels using the cable box.

SERVICE OPTICAL

S-VIDEOS-VIDEO

ANTANT. IN. IN

AC INPUTAC INPUT

SERVICE

S-VIDEOS-VIDEO

AV1V1

VIDEOVIDEO

AUDIOAUDIO

AV2V2

VIDEOVIDEO

AUDIOAUDIO

Cable

(R) AUDIO (L) VIDEO

VCR

Cable

(R) AUDIO (L) VIDEO

VCR

Watching Cable TV

When connecting the set to an external source, match the colours of AUDIO/VIDEO input jacks on the set with the output jacks on the audio/video equipment: Video = yellow, Audio (Left) = white, Audio (Right) = red.

Use the INPUT SELECT button on the remote control to select AV 1 or AV 2 .

Operate the corresponding external equipment. See external equipment operating guide.

SERVICE OPTICAL

S-VIDEOS-VIDEO

ANTANT. IN. IN

AV1V1

VIDEOVIDEO

AUDIOAUDIO

AV2V2

VIDEOVIDEO

AUDIOAUDIO

AUDIO VIDEO

Watching external AV source

For cable TV

< Cable Box >

< Back panel of the set >

Camcorder

Video game set

< Back panel of the external

equipment >

Connection to

External equipment

• Component Input ports

You can get better picture quality if you connect DVD player with component input ports as below.

How to connect

Connect DVD video inputs to Y, PB, PR of COMPONENT (DVD INPUT) and audio inputs to Audio sockets of AUDIO INPUT.

How to use

Turn on the DVD player, and insert a DVD.

Use INPUT SELECT button on the remote control to select Component. Refer to the DVD player's manual for oper-

ating instructions.

Watching DVD

SERVICE OPTICAL

S-VIDEOS-VIDEO

ANTANT. IN. IN

AV2V2

VIDEOVIDEO

AUDIOAUDIO

AUDIO INPUTAUDIO INPUT

AUDIOAUDIO

R L

COMPONENT COMPONENT INPUT INPUT

(480i/480p/720p/1080i)(480i/480p/720p/1080i)

Y P

AV1V1

VIDEOVIDEO

AUDIOAUDIO

(R) AUDIO (L)

S-VIDEO

< Back panel of the set >

< Back panel of a DVD player >

Component ports of the

set

Y PB

Video output ports of DVD player

Y Y Y Y

B-Y

Cb PB

R-Y

Cr P

Connection to

External equipment

Connect the signal cable from the monitor output socket of

the DVD player or Set top Box to the HDMI INPUT socket

of the set.

Connect the audio cable from the PC to the AUDIO INPUT

sockets of the set.

Press the INPUT SELECT button to select HDMI.

Switch on the HDMI, and the HDMI screen appears on the set.

HDMI input signal : 480p-60Hz, 576p-50Hz, 720p-50Hz,

720p-60Hz, 1080i-50Hz, 1080i-60Hz.

HDMI Interface with HDCP Copy Protection enables alldigital rendering of video without the losses.

This TV SET can receive the High-Definition Multimedia Interface(HDMI) or Input of Digital Visual Interface(DVI).

Connecting HDMI

RGB INPUTRGB INPUT

AUDIO INPUTAUDIO INPUT

AUDIOAUDIO

R L

COMPONENT COMPONENT INPUT INPUT (480i/480p/720p/1080i)(480i/480p/720p/1080i)

Y PbP

HDMI INPUTHDMI INPUT

HDMI OUTPUTHDMI OUTPUT

(R) (R) AUDIO (L)AUDIO (L)

< Back panel of the set >

< DVI signal input only>

Connection to

External equipment

Connect the signal cable from the monitor output socket

of the PERSONAL COMPUTER to the RGB INPUT sock-

et of the set.

Connect the audio cable from the PC to the AUDIO INPUT sockets of the set.

Press the INPUT SELECT button to select PC-RGB.

Switch on the PC, and the PC screen appears on the set.

The set can be operated as the PC monitor.

RGB input signal : 480p-60Hz, 576p-50Hz, 720p-50Hz,

720p-60Hz, 1080i-50Hz, 1080i-60Hz.

Connecting PC

RGB INPUT

AUDIO INPUT

HDMI INPUT

AUDIO INPUTAUDIO INPUT

AUDIOAUDIO

R L

RGB OUTPUTRGB OUTPUT

(R) (R) AUDIO (L)AUDIO (L)

< Back panel of the set >

- Send the set’s audio to external audio equipment (stereo system) via the Digital Audio Output (Optical)

Caution : Do not look into the optical output port. Looking

at the laser beam may damage your vision.

How to connect

Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.

Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment.

Note : Digital Audio Output works, when it’s inputted HDMI signal to the set.

Connecting Digital Audio

SERVICE OPTICAL

S-VIDEO

ANT.IN. IN

AC INPUTAC INPUT

AV2

VIDEO

AUDIO

< Back panel of the set >

Basic operation

Press the F / G button to adjust the

volume.

If you want to switch the sound off,

press the MUTE button.

You can cancel it by pressing the

MUTE, F / G, button.

You can select a programme number with the

D / E

or NUMBER buttons.

Press the main power button to switch the set on.

If the set is in standby mode, press

the POWER,

D / E

buttons on the remote control handset to switch it on fully.

Press the POWER button on the

remote control handset.

The set reverts to standby mode.

Press the main power button again to switch the set off.

On and Off

Programme selection

Volume adjustment

Press the button and then use

D / E

button to select the Installation menu.

Press the OK button and then use

D / E

button to select Language.

Press the OK button and then use

D / E

button to select your desired language.

All the on screen displays will appear in the selected language.

Press the button to return to normal TV viewing.

On screen language selection

- The dialogue between you and your set takes place on screen with an operator menu. The buttons required for the operating steps are also displayed.

Press the button and then use

D / E

button to display each

menu.

Press the OK button and then use

D / E

button to select a menu item.

Press the OK button to display the sub

menu or the pull-down menu.

Change the setting of an item in the sub

or pull-down menu with F / G or

D / E

You can move to the higher level menu with F button and to move to the lower level menu press the G button.

Note : Menus may vary according to input mode.

On screen menus

Menu selection

INFO

GRUNDIG

Settings

Preset list

Installation

PIP

Information

Select and open

Exit

P+

P-

+ 30 hidden pages