Groen HY-6SE w/TDC/3-20 General Manual

HyPerSteam Pressureless Steamer

Description

Steamer shall be a Groen HyPLUS™ Model HY-6SEw/
TDC/3-20, stainless steel twin cavity, 6 pan pressureless
steamer, with 20 quart tilting steam jacketed kettle, and
cabinet mounted (specify 24, 36 or 48) electric steam
boiler, per Bulletin 78Aa and as follows:

Construction

Steamer cavities and cabinet base shall be all stainless
steel construction. Steamer unit shall have a unitized
body with removable right side panel providing access
to internal component. Steamer doors are all stainless
steel with strong continuous hinge, are field reversible
and provided with a one piece, replaceable seal. Hidden
magnetic door switch cuts power to blower and steam
flow to that cavity, when the door is opened. Pan support
racks shall be polished stainless steel and removable for
easy cleaning. Wide drip sink with condensate drain is
positioned under cavity doors.

Kettle shall have one piece welded construction of Type
304 stainless steel, with reinforced rim and butterfly
shaped pouring lip. Kettle support legs shall be heavy
tubular stainless steel. Flush mounted pouring sink with
splash shield standard.

36” wide cabinet base shall have stainless steel frame
with all stainless steel top deck, removable front access
doors, with side and rear panels standard. Front and rear
legs shall have adjustable bullet feet. Flanged feet are an
available option.

Finish

Cabinet exterior, including door, shall be finished to a #3
uniform finish. Cavity interiors are electro polished stain­less steel. Kettle exterior shall be polished to a bright high
buff finish.

ASME Code & UL Approval

Cabinet mounted boiler shall be ASME Code constructed
and National Board Registered for operation up to 15
PSI. Steamer unit and cabinet mounted boiler shall be
UL listed.

Sanitation

Unit shall be designed and manufactured to meet NSF
known health department and sanitation codes and be
NSF listed.

Controls

Steamer cavity controls shall be mounted on the front
panel for easy replacement or repair and will include a
separate ON-OFF/60 minute timer control with constant
steam setting, for each cavity. Kettle steam control valve
and HOT/COLD water faucet handles will be front mounted
with boiler controls. Electric boiler shall be provided with
a gas control valve, power-ON switch, RESET light, start
switch, low water sensor, pop safety valve, water level
sight glass and outside cabinet mounted pressure gauge.

Performance Features

Unit will shut off if water level is low or unit builds too
much pressure. When power switch is turned “off,” the
boiler automatically drains to reduce sediment build-up,
after water has cooled to 70ºF.

Each steamer cavity shall have a powerful side mounted
blower, which increases steam velocity and provides effi­cient steam distribution throughout cavity and between

loaded pans.

Cabinet Base Steam Source

Unit shall have twin electric-heated, cabinet-mounted
pressure boiler to provide atmospheric steam to each
chamber at a temperature of approximately 212ºF and
steam to kettle at approximately 12 PSI. The 24KW model
delivers 2.2 boiler horsepower, the 36 KW model delivers

3.5 boiler horsepower and the 48 KW model delivers 4.7
boiler horsepower.

Hot & Cold Water Faucet

Unit shall be provided with hot and cold water faucet with
swing spout standard.

Pan Capacity

Pan Size Per Cavity Total

12 x 20 x 1” 6 12

12 x 20 x 2 1/2” 3 6

12 x 20 x 4” 2 4

Options/Accessories

Independent cold water to condensate spray
Cover and-or basket insert for kettle

Installation

Specify 208, 240 or 480 Volt, 3 phase, 60 cycle electrical
service. Unit requires 1/2” NPT cold water supply line, 3/8”
NPT hot water supply line for faucet and 11/4” NPT free
venting drain.

Steam Source for Adjacent Equipment

A 1/2” NPT power take-off valve shall be standard. To ensure
proper performance, boiler must be sized to meet boiler
horsepower requirements of steamer cavities, 20 quart
kettle AND additional equipment. Appropriate steam traps
and piping must be installed for that additional equipment.

Water Supply Requirements

All water boiler systems are subject to contamination and
failure due to mineral content found in most water supplies.
To minimize service problems, a water treatment (soften­ing) system is recommended when water quality is found to
exceed limits stated on other side and in operator manual.

Origin of Manufacture

Steamer/Kettle Combination shall be designed and manu­factured in the United States.

model HY-6SE w/TDC/3-20

6-Pan Capacity
Stainless Steel
Pressureless Steamer/
Kettle Combination

With Electric
Pressure Boiler in
Cabinet Base

Short Form

Unit shall be a Groen HyPLUS™
pressureless steamer Model
HY-6SE w/TDC/3-20, with 20
quart tilting kettle powered
by electric pressure boiler
mounted in 36” wide cabinet
base, per Bulletin 78Aa. All
stainless steel construction
with two independent steamer
chambers, each with powerful
blower to circulate steam
within cavity and individual
60 minute timer with constant
steam setting. Steamer doors
are insulated, field reversible,
with easy open latch and
hidden magnetic door switch.
Drip sink with condensate
drain is provided under cavity
doors. Three (21/2” deep)
pan capacity per chamber.
Cabinet base has stainless
steel frame, all stainless steel
exterior, with removable front
access doors and adjustable
bullet feet. Pouring sink and
HOT/COLD water faucet
provided for kettle. Boiler
ASME code constructed for 15
PSI maximum, with choice of
24, 36, or 48KW power input.
Power take-off to divert steam
to adjacent equipment is
standard. UL listed, unit comes
standard with automatic boiler
drain. See other side for water,
drain and electric connections
required. Made in USA.

Applications

Pasta
Rice
Vegetables (Fresh & Frozen)
Seafood (Fresh & Frozen)
Poultry
Potatoes
Eggs
Meats
Reheat Cook-Chill &
Prepared Foods

1055 Mendell Davis Drive, Jackson, MS 39272
888-994-7636, unifiedbrands.net

Please reference our website for the most
updated product information and specifications.

Groen HyPerSteam, Page 14

160179C

Revised 08/09

7

(192)

Model HY-6SE w/TDC/3-20

P/N 121505 REV G

1

21

4

(540)

1

18

2

(470)

9

16

1

2

4

3

6

CONDENSATE
DRAIN VENT

SINK

DRAIN

5

1

8

2

(216)

CLEARANCE
SEE NOTE 1

(102)

4

(508)

20

5

57

(1453)

9

26

16

(675)

1

(38) MIN.

1

2

5

(67) MAX.

2

8

4

(117)

TM

READY ON

WATER FILL

LOW WATER

HIGH PRESSURE

5
8

36

(918)

A

E

M

T

S

1
8

SERVICE CONNECTIONS:

DRAIN CONNECTION: 1-1/4" NPT

1

(INCLUDES AUTOMATIC & MANUAL BOILER, STEAMERS, CONDENSATE SPRAY, KETTLE & SINK)

2

COLD WATER SUPPLY: 1/2" NPT (FOR BOILER, CONDENSATE SPRAY & FAUCET)

3

OPTION: SEPARATE CONDENSATE SPRAY 3/8" NPT (ADD KIT #MS102210)

4

HOT WATER SUPPLY: 3/8" NPT (FOR FAUCET)

MAIN ELECTRICAL CONNECTION (ALL UNITS): 1-31/32" DIA. HOLE

5

(REF. 1-1/2" CONDUIT KNOCK-OUT)

STEAM POWER TAKE-OFF: 1/2" NPT

6

NOTES:

1. DIMENSIONS IN BRACKETS ( ) ARE MILLIMETERS.

MAXIMUM

HEATER ELEMENT CURRENT

*

208V 240V 480V

1

UN-TREATED

(OPTIONAL)

DETAIL VIEW

29A58A67A

58A116A134A

4

3

2

23

(586)

2

(51)

WATER
SUPPLY
CONN.

121505 REV. G

6

1

16

5

24

16

(618)

24KW

36KW

100A 87A 44A

48KW

* AMPS (EACH LINE), 3 PHASE

3

16

5

3

8

8

(213)

ADJUSTABLE

BULLET FEET

34

(868)

3

16

OF WATER CONNECTIONS

(IF SECOND CONNECTION ORDERED)

TREATED
WATER
SUPPLY
CONN.

1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net

© 2009 Unified Brands. All Rights Reserved. DOVER® and the DOVER® Logo are registered
trademarks in the United States [and various other countries] of Unified Brands, a
wholly-owned subsidiary of Dover Corporation.