Groen HY-6SE-36 User Manual

HYPERSTEAM PRESSURELESS STEAMER

PROJECT NAME:

LOCATION:

ITEM NO:

MODEL HY-6SE-36

Steamer shall be a direct steam powered Groen HyPLUS Model HY-6SM, stainless steel twin cavity, 6 pan
cabinet mounted pressureless steamer, per Bulletin 76Ca and as follows.

CONSTRUCTION: Steamer cavities and cabinet

base shall be all stainless steel construction. Steamer unit
shall have a unitized body, with removable right side panel
providing access to internal components. Steamer doors are
all stainless steel with strong continuous hinge and are field
reversible for left or right swing. Doors shall be insulated
and provided with a one-piece, replaceable seal. Easy
open handle and latch shall provide positive lock and seal
when door is pushed or slammed shut. Hidden magnetic
door switch cuts power to blower and steam flow to that
cavity, when the door is opened. Pan support racks shall be
polished stainless steel and removable for easy cleaning.
Wide drip sink with condensate drain is positioned under
cavity doors. 36” wide cabinet base shall have stainless steel
frame with all stainless steel top deck, with hinged front
access panel and removable side and rear panels standard.
Front and rear legs shall have adjustable bullet feet. Flanged
feet are an available option.

FINISH: Cabinet exterior including doors shall be finished

to a #3 uniform finish. Cavity interiors are polished stainless
steel. Control panel face plates shall be smudge resistant
polyester film, ensuring maximum ease in cleaning and
maintaining a brilliant finish.

ASME CODE & UL LISTING: Cabinet mounted

boiler shall be ASME Code constructed and National Board
registered for operation up to 15 PSI. Steamer unit and
cabinet mounted boiler shall be UL listed.

SANITATION: Unit shall be designed and constructed

to meet NSF and known health department and sanitation
codes and be NSF listed.

CONTROLS: Steamer cavity controls shall be mounted

on the front panel for easy replacement or repair and will
include separate ON-OFF/60 minute timer control with
constant steam setting, for each cavity. Electric boiler shall be
provided with a power-ON switch, RESET light, start switch,
low water sensor, pop safety valve, water level sight glass
and outside cabinet mounted pressure gauge.

PERFORMANCE FEATURES: Unit will shut off

if water level is low or unit builds too much pressure. When
power switch is turned “off,” the boiler automatically drains to
reduce sediment build-up, after water has cooled to 170°F.

Each steamer cavity shall have a powerful side mounted
blower, which increases steam velocity and provides
efficient steam distribution throughout cavity and between
loaded pans.

CABINET BASE STEAM SOURCE: Unit

shall have an electric heated cabinet mounted pressure
boiler to provide atmospheric steam to each chamber
at a temperature of approximately 212°F. The 24KW
model delivers 2.2 boiler horsepower, the 36KW model
delivers 3.5 boiler horsepower and the 48 KW model
delivers 4.7 boiler horsepower.

PAN CAPACITY:

Pan Size/Type Per cavity Total

12 x 20 x 1” 6 12

12 x 20 x 2 1/2” 3 6

12 x 20 x 4” 2 4

INSTALLATION: Specify 208, 240 or 480 Volt, 3

phase, 60 cycle electrical service. Unit requires 1/2” NPT
cold water supply line and 1 1/4” NPT free venting drain.

STEAM SOURCE FOR ADJACENT
EQUIPMENT:

shall be standard. To ensure proper performance, boiler
must be properly sized to meet boiler horsepower
requirements of steamer cavities AND additional
equipment. Appropriate steam traps and piping must be
professionally installed.

A 1/2” NPT power take-off valve

WATER SUPPLY REQUIREMENTS: All

water boiler systems are subject to contamination
and failure due to mineral content found in most
water supplies. To minimize service problems, a water
treatment (softening) system is recommended when
water quality is found to exceed limits stated below and
in operator manual. Recommended MINIMUM water
quality standards are: Total dissolved solids (TDS) content
should not exceed 30 parts per million; and the water pH
should be 7.0 to higher.

ORIGIN OF MANUFACTURE: Designed and

manufactured in the United States.

QTY:

MODEL NO:

AIA NO:

SIS NO:

6-Pan capacity stainless steal
pressureless steamer, with electric
pressure boiler in cabinet base.
(model HY-6SE-36 shown)

OPTIONS/ACCESSORIES:

Flanged mounting feet
Independant water supply to

consensate spray

HyPerSteam

160177 RevB

Revised 04/11

30

(778)

(76)

5
8

3

1

2

2

(64)

4

3

21

16

(538)

SEE NOTE 1

7

(192)

HY-6SE-36

1

21

4

(540)

1

18

2

(470)

9

16

1

14

(365)

FLUE

3

18

16

(462)

2

5

3

6

3
8

CONDENSATE
DRAIN VENT

4

CLEARANCE
SEE NOTE 1

6

(152)

NATURAL

PROPANE

RECOMMENDED

INCOMING GAS PRESSURE

5" W.C. (MIN.)

14" W.C. (MAX.)

11" W.C. (MIN.) 14" W.C. (MAX.)

*

INCHES WATER COLUMN

INPUT RATE (BTU/HR.): 200,000

OPERATING

*

GAS PRESSURE

OUTPUT RATE (BTU/HR.): 120,000

CLEARANCECLEARANCE
SEE NOTE 1

24

(51)(102)

BOILER HORSEPOWER: 3.7

P/N 121511 REV D

*

3.5" W.C.

10.0" W.C.

3

57

16

(1453)

9

26

16

(675)

5

4

(117)

8

36

(918)

1
8

1

2

1
2

5

(67) MAX.

8

(38) MIN.

SERVICE CONNECTIONS:

DRAIN CONNECTION: 1-1/4" NPT

1

(INCLUDES AUTOMATIC & MANUAL BOILER, STEAMERS, & CONDENSATE SPRAY)

2

COLD WATER SUPPLY: 1/2" NPT (FOR BOILER & CONDENSATE SPRAY)

3

OPTION: SEPARATE CONDENSATE SPRAY 3/8" NPT (ADD KIT #MS102210)

4

ELECTRICAL CONNECTION: 7/8" DIA. HOLE (REF. 1/2" CONDUIT KNOCK-OUT)

5

GAS CONNECTION: 1/2" NPT

6

STEAM POWER TAKE-OFF: 1/2" NPT

NOTES:

1. MINIMUM CLEARANCE FROM COMBUSTIBLE MATERIALS

RIGHT SIDE 2" (51)

LEFT SIDE 4" (102)

REAR 6" (152)

2. DIMENSIONS IN BRACKETS ( ) ARE MILLIMETERS.

ADJUSTABLE

BULLET FEET

34

(868)

2

1

TREATED
WATER
SUPPLY
CONN.

DETAIL VIEW

3

(98)

(51)

UN-TREATED

WATER
SUPPLY
CONN.

(OPTIONAL)

4

11

9

16

(246)

3

16

OF WATER CONNECTIONS

(IF SECOND CONNECTION ORDERED)

6

3

1

23

16

(586)

7
8

5

24

(618)

5

16

2

121511 REV D

1055 Mendell Davis Drive, Jackson, MS 39272, 888-994-7636, unifiedbrands.net

© 2013 Unified Brands. All Rights Reserved. Unified Brands is a wholly-owned subsidiary of Dover Corporation.