Grizzly G1033Z User Manual
INTRODUCTION
The Model G1033Z is the same planer as the
Model G1033 with the upgrade of the chromed
3-roller extension rollers and 5 HP motor.
INVENTORY
1. Planer Unit .................................................. 1
2. Dust Hood .................................................. 1
3. Starter Switch Assembly ............................ 1
4. Table Extension Roller Assembly .............. 2
5. Handwheel ................................................. 1
6. Handwheel Handle .....................................
6. Hardware Bag :
— Hex Bolt M6-1 x 12 .................................
— Flat Washer 6mm ...................................
— Hex Bolt M10-1.5 x 25 ............................
— Flat Washer 1/2" .....................................
— Knife Setting Rod ....................................
— Knife Setting Gauge ...............................
— E-Clip Ring 9mm .....................................
—Hex Nut M12-1.75 ..................................
—Flat Washer 12mm .................................
—Direction Label ........................................
— Allen Wrench 3mm .................................
— Allen Wrench 4mm ................................
— Allen Wrench 5mm .................................
— Allen Wrench 6mm .................................
— Open End Wrench 8/10mm ....................
— Open End Wrench 12/14mm ..................
— Open End Wrench 17/19mm ..................
1
6
6
8
8
1
2
4
1
1
1
1
1
1
1
1
1
1
RECOMMENDED FOR SETUP
G1738—Rotacator™ Precision Planer Tool
The Rotacator is a dial indicator on a magnetic
base designed for quickly and accurately setting
the critical tolerances needed when adjusting
planers to avoid chattered cuts.
MANUAL INSERT
Model G1033Z
20" 5 HP Planer
Figure 1. Model G1033Z.
Figure 2. Rotacator™ Precision Planer Tool is
an important tool for setting up your planer for
the highest quality results.
Helps adjust infeed/outfeed rollers, pressure bars,
chip breakers, and bed rollers. Also a great setup
tool for other machines! Accurate to 0.001".
Indicator rotates 360˚.
G1033Z Replacement Parts
REF PART # DESCRIPTION
17 P1033Z017 MOTOR PULLEY
17-1 PSS04M SET SCREW M6-1 X 12
83 PVM58 V-BELT M-58 3L580
86 P1033Z086 SWITCH BRACKET
87 P1033Z087 MAGNETIC SWITCH MA-30
92 P1033Z092 STRAIN RELIEF MG25A
93 P1033Z093 MOTOR CORD 10AWG X 3C
109 P1033Z109 PLASTIC SWITCH CVR SCREW
211 P1033211 3 HOLE ROLLER BRACKET
212 P1033212 CHROME ROLLER
212-1 P1033Z212-1 PLASTIC BUSHING
212-2 P1033Z212-2 ROLLER ROD
218 PB02M HEX BOLT M6-1 X 12
COPYRIGHT © MARCH, 2005. BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR7023 PRINTED IN TAIWAN
REF PART # DESCRIPTION
219 PW01M FLAT WASHER 8MM
401 P1033Z401 CABINET STAND
405 P1033Z405 MOTOR MOUNT
414 P1033Z414 5 HP MOTOR
414-1 P1033Z414-1 MOTOR FAN COVER
414-2 P1033Z414-2 MOTOR FAN
414-3 P1033Z414-3 CAPACITOR COVER
414-4 P1033Z414-4 S CAP. 800M 250V 1-3/8 X 3-3/4
414-5 P1033Z414-5 JUNCTION BOX
415 P1033Z415 KEY 8 X 7 X 55
417 P1033Z417 POWER CORD 10AWG X 3C
418 P1033Z092 STRAIN RELIEF MG25A
20'' PLANER
MODEL G1033
INSTRUCTION MANUAL
COPYRIGHT © 1990 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
REVISED APRIL, 1999. PRINTED IN U.S.A.
G1033 20" Planer -1-
Table Of Contents
PAGE
1. SAFETY
SAFETY RULES FOR POWER TOOLS ..................................................................................2-3
ADDITIONAL SAFETY INSTRUCTIONS FOR PLANERS ..........................................................4
2. CIRCUIT REQUIREMENTS
220V OPERATION ......................................................................................................................5
FUSING ........................................................................................................................................5
GROUNDING................................................................................................................................5
EXTENSION CORDS ..................................................................................................................5
3. INTRODUCTION
COMMENTARY ............................................................................................................................6
UNPACKING ................................................................................................................................7
PARTS INVENTORY....................................................................................................................7
CLEAN UP....................................................................................................................................8
SITE CONSIDERATIONS ............................................................................................................8
4. ASSEMBLY
OVERVIEW ..................................................................................................................................9
EXTENSION ROLLERS ..............................................................................................................9
HANDWHEEL ..............................................................................................................................9
DUST HOOD ..............................................................................................................................10
SWITCH......................................................................................................................................10
KNIFE SETTING JIG ..................................................................................................................11
5. ADJUSTMENTS
CHAIN ADJUSTMENT................................................................................................................12
TABLE ADJUSTMENT ..............................................................................................................12
CHAIN DRIVE ............................................................................................................................13
BED ROLLERS ..........................................................................................................................14
KNIFE INSPECTION ..................................................................................................................15
KNIFE ADJUSTMENT ................................................................................................................15
FEED ROLLER SPEED..............................................................................................................16
ROLLER ADJUSTMENT ......................................................................................................16-17
SPRING TENSION ....................................................................................................................17
CHIP BREAKER ........................................................................................................................18
PRESSURE BAR........................................................................................................................18
CHIP DEFLECTOR ....................................................................................................................19
STATIC CHAIN ADJUSTER ......................................................................................................19
SCALE ADJUSTMENT ..............................................................................................................20
ANTI-KICKBACK FINGERS ......................................................................................................20
6. OPERATIONS
TEST RUN..................................................................................................................................21
OPERATIONAL TIPS ................................................................................................................21
WOOD CHARACTERISTICS ....................................................................................................22
7. MAINTENANCE
GENERAL ..................................................................................................................................23
KNIVES ......................................................................................................................................23
LUBRICATION............................................................................................................................24
BELT TENSION..........................................................................................................................25
BELT ALIGNMENT ....................................................................................................................25
8. CLOSURE
MACHINE DATA ........................................................................................................................27
TROUBLESHOOTING................................................................................................................28
PARTS BREAKDOWN AND PARTS LISTS ........................................................................29-35
ADJUSTMENT BLOCK PATTERN ............................................................................................36
WIRING DIAGRAM ....................................................................................................................37
WARRANTY AND RETURNS ....................................................................................................38
-2- G1033 20" Planer
Safety Instructions For Power Tools
SECTION 1: SAFETY
5. KEEP CHILDREN AND VISITORS
AWAY. All children and visitors should be
kept a safe distance from work area.
6. MAKE WORK SHOP CHILD PROOF with
padlocks, master switches, or by removing
starter keys.
7. DON’T FORCE TOOL. It will do the job
better and safer at the rate for which it was
designed.
8. USE RIGHT TOOL. Don’t force tool or
attachment to do a job for which it was not
designed.
1. KEEP GUARDS IN PLACE and in working
order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to
see that keys and adjusting wrenches are
removed from tool before turning on.
3. KEEP WORK AREA CLEAN. Cluttered
areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use power tools in damp or
wet locations, or where any flammable or
noxious fumes may exist. Keep work area
well lighted.
For Your Own Safety Read Instruction
Manual Before Operating This Equipment
Indicates an imminently hazardous situation which, if not
avoided, WILL result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not
avoided, MAY
result in minor or moderate injury. It may also
be used to alert against unsafe practices.
This symbol is used to alert the user to useful information
about proper operation of the equipment.
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words which are intended to convey the level
of importance of the safety messages. The progression of symbols is described below.
Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.
NOTICE
G1033 20" Planer -3-
9. USE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition. Conductor size should be in accordance
with the chart below. The amperage rating
should be listed on the motor or tool nameplate. An undersized cord will cause a drop
in line voltage resulting in loss of power and
overheating. Your extension cord must also
contain a ground wire and plug pin. Always
repair or replace extension cords if they
become damaged.
Minimum Gauge for Extension Cords
10. WEAR PROPER APPAREL. Do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewelry which may get
caught in moving parts. Non-slip footwear is
recommended. Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also
use face or dust mask if cutting operation is
dusty. Everyday eyeglasses only have
impact resistant lenses, they are NOT safety
glasses.
12. SECURE WORK. Use clamps or a vise to
hold work when practical. It’s safer than
using your hand and frees both hands to
operate tool.
LENGTH
AMP RATING 25ft 50ft 100ft
0-6 18 16 16
7-10 18 16 14
11-12 16 16 14
13-16 14 12 12
17-20 12 12 10
21-30 10 10 No
Safety Instructions For Power Tools
13. DON’T OVERREACH. Keep proper foot-
ing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep
tools sharp and clean for best and safest
performance. Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing
and changing accessories, such as blades,
bits, cutters, and the like.
16. REDUCE THE RISK OF UNINTENTIONAL STARTING. Make sure switch is in off
position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended accessories. The use of improper
accessories may cause risk of injury.
18. CHECK DAMAGED PARTS. Before fur-
ther use of the tool, a guard or other part
that is damaged should be carefully
checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding of moving parts, breakage of parts,
mounting, and any other conditions that
may affect its operation. A guard or other
part that is damaged should be properly
repaired or replaced.
19. NEVER LEAVE TOOL RUNNING UNATTENDED. TURN POWER OFF. Don’t
leave tool until it comes to a complete stop.
-4- G1033 20" Planer
Additional Safety Instructions For Planers
No list of safety guidelines can be complete. Every shop environment is different.
Always consider safety first, as it applies to
your individual working conditions. Use
this and other machinery with caution and
respect. Failure to do so could result in
serious personal injury, damage to equipment or poor work results.
1. Ensure that the machine sits firmly on the
floor before use. Any “wobbles” must be
corrected by shimming or blocking before
operation.
2. This machine is not designed to process
any other material except wood.
3. Never position fingers or thumbs near the
infeed roller.
4. Long stock should always be fully support-
ed by some type of support fixture.
5. Do not operate planer with dull or damaged
knives.
6. Ensure that the planer is properly adjusted
before using.
7. Do not remove excessive amounts of
wood in a single pass.
8. Inspect your stock before planing. Reject
stock with defects and foreign material
9. Do not attempt to remove jams until power
is disconnected and all moving parts have
come to a complete stop.
10. Provide adequate infeed and outfeed
space for operating the planer.
11. Do not plane wood less than 12" long and
1
⁄
4" thick.
12. Do not plane lumber with loose knots or
knots that may become loose during
planing.
Operating this equipment has the potential
to propel debris into the air which can
cause eye injury. Always wear safety glasses or goggles when operating equipment.
Everyday glasses or reading glasses only
have impact resistant lenses, they are not
safety glasses. Be certain the safety glasses you wear meet the appropriate standards of the American National Standards
Institute (ANSI).
Like all power tools, there is danger associated with the Model G1033 20" Planer.
Accidents are frequently caused by lack of
familiarity or failure to pay attention. Use
this tool with respect and caution to lessen
the possibility of operator injury. If normal
safety precautions are overlooked or
ignored serious personal injury may occur.
G1033 20" Planer -5-
220V Operation
SECTION 2: CIRCUIT REQUIREMENTS
The Model G1033 should be fused at 30 amps.
Fusing at amperage ratings higher than 30 amps
will not adequately protect the motor. You are
cautioned that equipment that is returned to us
for service that shows evidence of being overfused will be repaired or replaced totally at the
customer’s expense, regardless of the present
warranty status.
Fusing
We do not recommend the use of extension cords
on 220V equipment. It is much better to arrange
the placement of your equipment and the
installed wiring to eliminate the need for extension cords. Should it be necessary to use an
extension make sure the cord is rated Hard
Service (grade S) or better. Refer to the chart in
Section 1: Safety Instructions to determine the
minimum gauge for the extension cord. The
extension cord must also contain a ground wire
and plug pin. Always repair or replace extension
cords when they become worn or damaged.
Extension Cords
Grounding
This equipment must be grounded. Please
ensure that this machine is continuously
grounded from the motor to the machine frame
and then to a known ground. Verify that any
existing electrical outlet and circuit you intend
to plug into is actually grounded. If it is not, it
will be necessary to run a separate 12 A.W.G.
copper grounding wire from the outlet to a
known ground. Under no circumstances should
the grounding pin from any three-pronged plug
be removed. Serious injury may occur.
Figure 1. Twist-lock style 30A connector.
In the event of an electrical short, grounding
reduces the risk of electric shock by providing a
path of least resistance to disperse electric current. This tool is equipped with a power cord having an equipment-grounding conductor. The outlet must be properly installed and grounded in
accordance with all local codes and ordinances.
The 3 HP G1033 Planer motor is wired to operate at 220V only. A 220V plug that matches your
220V receptacle must attach to the end of the
power cord. Plugs and receptacles can be purchased at your local hardware store or home
center. When connecting to 220V, ensure that
the electrical circuit is in fact a 220V circuit.
Contact your local electrical contractor if uncertain about converting to 220V operation. A wiring
diagram for the motor and switch is provided at
the back of this manual should more detail be
needed.
When operating at 220V, we recommend using a
NEMA-style 6-30 plug and outlet. See Figure 1.
You may also “hard-wire” the planer directly to
your panel, provided you place a disconnect
switch near the machine.
-6- G1033 20" Planer
SECTION 3: INTRODUCTION
Commentary
We are proud to offer the Grizzly Model G1033
20" Planer. The Model G1033 is part of a growing
Grizzly family of fine woodworking machinery.
When used according to the guidelines set forth
in this manual, you can expect years of troublefree, enjoyable operation and proof of Grizzly’s
commitment to customer satisfaction.
The Model G1033 is designed for heavy-duty professional use. It features a powerful 3HP,
220V/240V single-phase motor, four-knife cutterhead, 2-speed automatic feed, precision-ground
table and a both a chipbreaker and a pressure
bar to support the stock as it moves through the
machine.
A number of optional accessories for the Model
G1033 are available through the Grizzly catalog.
They include a heavy-duty mobile base, roller
stands, replacement knives and Planer Pal
®
planer jigs, which are invaluable when setting up or
adjusting your planer’s cutting knives.
We are also pleased to provide this manual with
the Model G1033. It was written to guide you
through assembly, review safety considerations,
and cover general operating procedures. It represents our effort to produce the best documentation possible. If you have any comments regarding this manual, please write to us at the address
below:
Grizzly Industrial, Inc.
C
/O Technical Documentation
P.O. Box 2069
Bellingham, WA 98227-2069
Most importantly, we stand behind our machines.
If you have any service questions or parts
requests, please call or write us at the location
listed below.
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G1033 as supplied when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
Whenever possible, though, we send manual
updates to all owners of a particular tool or
machine. Should you receive one, we urge you to
insert the new information with the old and keep
it for reference.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: (570) 546-9663
Fax: (800) 438-5901
E-Mail: techsupport@grizzly.com
Web Site: http://www.grizzly.com
To operate this, or any power tool, safely
and efficiently, it is essential to become as
familiar with its characteristics as possible.
The time you invest before you begin to use
your Model G1033 will be time well spent.
DO NOT operate this machine until you are
completely familiar with the contents of this
manual. Make sure you read and understand all of the safety procedures. If you do
not understand something, DO NOT operate the machine.
G1033 20" Planer -7-
Unpacking
This planer is shipped from the factory in a carefully packed carton. If you find the machine to be
damaged after you’ve signed for delivery and the
truck and driver are already gone, you will need
to file a freight claim with the carrier. Save the
containers and all packing materials for inspection by the carrier or their agent. Without the
packing materials, filing a freight claim can be difficult. If you need advice regarding this situation,
please call us immediately.
The Model G1033 is a heavy machine (770
lbs. shipping weight). DO NOT over-exert
yourself while unpacking or moving your
machine – get assistance. In the event that
your planer must be moved up or down a
flight of stairs, be sure that the stairs are
capable of supporting the combined weight
of people and the machine. Failure to use
care while assembling or moving could
result in serious personal injury.
Parts Inventory
Take a quick inventory of the parts and put them
aside for assembly later. After all the parts have
been removed from the container, you should
have:
• Planer Unit
• Dust Hood
• Hand Wheel
• Starter Switch
• Rollers (2)
• Knife Gauge
• Bolt Bag
(2) 12mm Snap Rings
(2) 10mm Flat Washers
(8) M10x1.5 Hex Bolts
(8) 6mm Flat Washers
(4) Snap Rings
(6) M10x1.5 Hex Bolts
(6) Flat Washers
In the event that any non-proprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them, or, for the sake of expediency, replacements can be obtained at your local
hardware store.
NOTICE
A full parts list and breakdown can be found
toward the end of this manual. For easier
assembly, or to identify missing parts,
please refer to the detailed illustrations at
the end of the manual.
-8-
G1033 20" Planer
Site Considerations
FLOOR LOAD
Your G1033 Planer represents a large weight
load in a small footprint. Most commercial floors
are suitable for the Model G1033. Some residential floors may require additional build up to support both machine and operator.
WORKING CLEARANCES
Working clearances can be thought of as the distances between machines and obstacles that
allow safe operation of every machine without
limitation. Consider existing and anticipated
machine needs, size of material to be processed
through each machine, and space for auxiliary
stands and/or work tables. Also consider the relative position of each machine to one another for
efficient material handling. Be sure to allow yourself sufficient room to safely run your machines in
any foreseeable operation.
LIGHTING AND OUTLETS
Lighting should be bright enough to eliminate
shadow and prevent eye strain. Electrical circuits
should be dedicated or large enough to handle
combined motor amp loads. Outlets should be
located near each machine so power or extension cords are not obstructing high-traffic areas.
Be sure to observe local electrical codes for proper installation of new lighting, outlets, or circuits.
Make your shop “child safe”. Ensure that
your workplace is inaccessible to youngsters by closing and locking all entrances
when you are away. Never allow visitors in
your shop when assembling, adjusting or
operating equipment.
Clean Up
The unpainted surfaces are coated with a waxy
oil to protect it from corrosion during shipment.
Remove this protective coating with with a solvent cleaner or citrus-based degreaser. Avoid
chlorine-based solvents as they may damage
painted surfaces should they come in contact.
Always follow the usage instructions on the product you choose for clean up.
Many of the solvents commonly used to
clean machinery can be highly flammable,
and toxic when inhaled or ingested. Always
work in well-ventilated areas far from potential ignition sources when dealing with solvents. Use care when disposing of waste
rags and towels to be sure they do not create fire or environmental hazards. Keep children and animals safely away when cleaning and assembling this machine.
Do not use gasoline or other petroleumbased solvents to remove this protective
coating. These products generally have
low flash points which makes them
extremely flammable. A risk of explosion
and burning exists if these products are
used. Serious personal injury may occur.
Some die-cut metal parts may have sharp
edges (called “flashing”) on them after they
are formed. Please examine the edges of all
die-cut metal parts before handling them.
Failure to do so could result in injury.
G1033 20" Planer -9-
SECTION 4: ASSEMBLY
Overview
Most of your G1033 Planer has been assembled
at the factory, but some parts must be assembled
or installed after delivery. We have organized the
assembly process into steps. Please follow along
in the order presented here.
TOOLS REQUIRED: Most of the tools required
for assembly are included with the planer.
However, you will also need a Phillips
®
and regular screwdriver, metric wrenches, as well as a
feeler gauge for adjustments.
Extension Rollers
The Model G1033 is supplied with extension
rollers on both the infeed and outfeed ends of the
table. The roller assemblies are identical for both
infeed and outfeed. To attach the extension
rollers:
1. Attach an extension bar to the end of each
roller and secure with the 12mm snap rings
provided.
2. The assembled extension rollers attach to
the ends of the planer’s table. Match the
tapped holes on the side of the table to the
extension bars and attach with the M10 x
1.5 Hex Bolts and washers provided. See
Figure 2.
3. Before final tightening, run a straight edge
across the table and past each roller.
Position the rollers flush with the table and
tighten the Hex Bolts securely.
Figure 2. Extension roller attachment.
Extension
Mounting Bolts
Hand Wheel
The hand wheel operates the chain driven system which raises and lowers the table to control
cutting depth. To attach the hand wheel:
1. Place the handwheel on the worm gear
shaft and secure with hex nut and washer
provided. See Figure 3.
2. Attach the handle to the handwheel and
tighten hex nut.
Figure 3. Attaching handwheel.
-10- G1033 20" Planer
Dust Hood
The G1033 features a dust hood with a 5'' dust
port. It is only to be used in conjunction with a
dust collection system. Install the dust hood as
follows:
1. Match the mounting holes on the dust hood
with the tapped holes on the outfeed end of
the cutterhead casting.
2. Using the six M6-1.0 Hex bolts provided,
secure the dust hood to the cutterhead
casting. See Figure 4.
See note regarding the use of a dust collector
and chip deflector adjustment in the adjustment
section of this manual.
Figure 4. Dust hood in place.
Switch
The magnetic ON/OFF switch supplied with the
Planer is pre-wired to the motor. The remaining
step requires connecting the switch to the planer's head casting. To attach the switch:
1. Align the holes on the flanges at the back of
the switch box with the tapped holes on the
front left corner of the head casting.
2. Using the socket head cap screws provid-
ed, attach the switch box assembly to the
head casting. See Figure 5.
The G1033 is shipped without a plug. Now would
be a good time to attach the appropriate plug
specified in Section 2: Circuit Requirements.
Figure 5. Attaching switch.
Do not attempt to make any adjustments to
this machine or perform routine maintenance without unplugging it from its power
source. Serious injury could result.
DO NOT attach the dust hood if you do not
intend to connect the Model G1033 to a dust
collection system. Accumulated wood chips
could cause a malfunction, resulting in personal injury or damage to the planer.
Loading...