Grandstream Networks GWN7600LR Quick Installation Guide
Grandstream Networks, Inc.
126 Brookline Ave, 3rd Floor
Boston, MA 02215. USA
Tel : +1 (617) 566 - 9300
Fax: +1 (617) 249 - 1987
www.grandstream.com
For Warranty and RMA information, please visit www.grandstream.com
Outdoor Long Range 802.11ac Wave-2
GWN7600LR
WiFi Access Point
Quick Installation Guide
Content
English................................................................................1
简体中文............................................................................8
Español..............................................................................14
Français..............................................................................21
Deutsch..............................................................................28
Italiano...............................................................................35
Русскй...............................................................................42
Português.......................................................................... 49
Polski................................................................................ 56
EN
OVERVIEW
This long range WiFi access point is designed to provide extended coverage support and is ideal for outdoor WiFi solutions thanks to its waterproof casing and heat resistant technology. The GWN7600LR comes
equipped with dualband 2x2:2 MU-MIMO with beam-forming technology
and a sophisticated antenna design for maximum network throughput
and extended WiFi coverage range of up to 300 meters. To ensure easy
installation and management, the GWN7600LR uses a controller-less
distributed network management design and an embedded controller
within the product’s web user interface. This allows each access point to
manage a network of up to 30 GWN APs independently without needing separate controller hardware/software and without a single pointof-failure. Its easy installation and management features packed with
extra coverage support and advanced performance features, make the
GWN7600LR an ideal outdoor access point for mid-size wireless network deployments.
PRECAUTIONS
● Do not attempt to open, disassemble, or modify the device.
● Do not expose this device to temperatures out the range of -30 °C to
60 °C for operating and -30°C to 70°C for storage
● Do not expose the GWN7600LR to environments outside of the follow-
ing humidity range: 5-95% RH (non-condensing).
● Do not power cycle your GWN7600LR during system boot up or rm-
ware upgrade. You may corrupt rmware images and cause the unit to
malfunction.
PACKAGE CONTENTS
4 x Screw
(PM8 x 115)
2 x Assembled
Screw
4 x Screws and
Anchors
1 x Quick Installation Guide
1 x GPL Statement
4 x Locknut
GWN7600LR PORTS
Port Description
NET/POE Ethernet RJ45 port (10/100/1000Mbps) supporting
PoE/ PoE+.
NET Ethernet RJ45 port (10/100/1000Mbps) to your
router or another GWN76xx.
RESET
Factory reset button. Press for 7 seconds to reset
factory default settings.
1 x GWN7600LR
Access Point
1 x Cover Bracket
~1~
1 x Base Bracket
POWERING AND CONNECTING THE GWN7600LR
GWN7600LR can be powered on via PoE switch using following steps:
Step 1: Plug a RJ45 Ethernet cable into the network port of the GWN-
7600LR.
~2~
Step 2: Plug the other end into the uplink port of the power over Ethernet
(PoE) switch.
Network Port
RJ45 Ethernet Cable
to power over Ethernet
(PoE) Switch
HARDWARE INSTALLATION
GWN7600LR can be mounted horizontally or vertically on a metal bar.
Please refer to the following steps for the appropriate installation.
4. Connect the Ethernet cable (RJ45) to the correct ports of your GWN7600LR.
5. Align the GWN7600LR with the Base Bracket and pull it down to the
right position.
6. Install the 2x Assembled screws to x GWN7600LR on the Mounting
Bolt.
4
5
Vertical Mounting
1. Prepare the Cover Bracket by inserting the 4 screws (PM8) into corresponding holes.
2. Attach the Cover Bracket with screws on the vertical Mounting Bolt
where GWN7600LR will be installed.
3. Assemble the Base Bracket with the Cover Bracket using provided
locknuts and screws (PM8).
3
1 2
~3~
Horizontal Mounting
1. Prepare the Cover Bracket by inserting the 4 screws (PM8) into corresponding holes.
2. Attach the Cover Bracket with screws on the horizontal Mounting Bolt
where GWN7600LR will be installed.
3. Assemble the Base Bracket with the Cover Bracket using provided
locknuts and screws (PM8).
3
2
1
~4~
4. Connect the Ethernet cable (RJ45) to the correct ports of your GWN7600LR.
5. Align the GWN7600LR with the Base Bracket and pull it down to the
right position.
6. Install the 2x Assembled screws to x GWN7600LR on the Mounting
Bolt.
4
5
CONNECT TO GWN7600LR DEFAULT WIFI NETWORK
GWN7600LR can be used as standalone access point out of box, or
after factory reset with Wi-Fi enabled by default.
After powering the GWN7600LR and connecting it to the network,
GWN7600LR will broadcast a default SSID based on its MAC address
GWN[MAC’s last 6 digits] and a random password.
Note: GWN7600LR’s default SSID and password information are
printed on the MAC tag of the unit.
~5~
ACCESSING THE CONFIGURATION INTERFACE
A computer connected to the GWN7600LR’s SSID, or to the same network as the GWN7600LR can discover and access its conguration interface using one of the below methods:
Method 1: Discover GWN7600LR using its MAC Address
1. Locate the MAC address on the MAC tag of the unit, which is on the
underside of the device, or on the package.
2. From a computer connected to same network as the GWN7600LR,
type in following address using GWN7600LR’s MAC address on your
browser https://gwn_<mac>.local
Example: If a GWN7600LR has the MAC address 00:0B:82:8C:4D:F8,
this unit can be accessed by typing https://gwn_000b828c4df8.local on
the browser.
~6~
Method 2: Discover GWN7600LR using GWN Discovery Tool
1. Download and install GWN Discovery Tool from the following link:
http://www.grandstream.com/tools/GWNDiscoveryTool.zip
2. Open the GWN DiscoveryTool, and click on Scan.
3. The tool will discover all GWN76XX Access Points connected on
the network showing their MAC and IP addresses.
4. Click on Manage Device to be redirected directly to the GWN-
7600LR’s conguration interface, or type in manually the displayed IP
address on your browser.
Using one of the above methods, the login screen will appear. Type in
“admin” in both Username and Password elds and click on Sign In.
概述
概述
此远程无线Wi-Fi接入点是为支持更大的信号覆盖面而设计的。此设备凭
借着良好的防水和耐热技术成为了户外Wi-Fi的理想设备。GWN7600LR
利用聚束技术支持双频段的2x2:2MU-MIMO，同时利用复杂的天线设计
以提供最大化的网络吞吐量以及高达300米的Wi-Fi覆盖面。为保证安装
和管理的简易性，GWN7600采用无控制器的分布式网络管理设计。通过
在产品的网页用户界面中嵌入控制器，实现每个接入点在保证不会产生故
障点的情况下，无需借助其他控制器硬件/软件就能独立管理由多达30个
GWN76xx系列AP构成的网络。凭借着安装和管理的简易性以及支持大
面积覆盖和其他优越的性能，GWN7600LR成为了理想的部署中型无线
网络的企业级无线AP。
注意事项
● 不要尝试打开，拆解或修改设备。
● 不要将本设备暴露在温度-30℃至60℃的工作环境或-30℃至70℃的储
存环境以外。
● 不要将本设备暴露在环境湿度如下范围以外：5-95％RH（无冷凝）。
● 系统启动或固件升级期间不要中断电源。这可能会损坏设备固件，并
导致设备故障。
包装内容
ZH
Notes:
● Make sure hat the GWN7600LR is not already paired with another
GWN76xx Access Point as slave, or GWN7000 Router Series, other-
wise the conguration interface cannot be accessed
● If the GWN7600LR is already paired, make sure to unpair it rst, or
do a factory reset.
● It is customer’s responsibility to ensure compliance with local regula-
tions for frequency bands, transmit power and others.
Refer to online documents and FAQ for more detailed information:
http://www.grandstream.com/our-products
~7~
1 x GWN7600LR 无线
接入点
4 x 螺丝
(PM8 x 115)
2 x 组合螺丝
1 x 安装支架后盖
4 x 螺丝和螺帽 4 x 防松螺母
1 x 快速安装手册
1 x GPL 声明
1 x 安装支架底座
~8~
GWN7600LR 端口
硬件安装
GWN7600LR可以安装在横向和纵向杆子上。
请按照如下步骤进行正确安装。
纵杆安装
1. 将4个(PM8)螺丝插入安装支架后盖的四个螺丝孔中备用。
2. 将装有螺丝的安装支架后盖的凹槽对准将要安装GWN7600LR的纵杆并
卡入。
3. 利用安装包内的防松螺母和（PM8）螺丝，将安装支架后盖和安装支
架底座组装起来。
Port Description
NET/POE
NET
RESET
以太网RJ45端口（10/100 /1000Mbps），支持PoE/
PoE+。
以太网RJ45端口（10/100 /1000Mbps），连接至路
由器或另一个GWN76xx。
恢复出厂设置按钮。按7秒恢复出厂默认设置。
上电和连接 GWN7600LR
通过如下方式可对GWN7600LR 进行PoE供电：
Step 1: 将以太网电缆的RJ45端口插入GWN7600LR的网络端口中；
Step 2: 将电缆的另一端插入交换机的PoE级联端口。
网络端口
RJ45电缆连接到以太网
供电的（PoE）交换机
或者PoE供电转换头。
~9~
3
2
1
4. 将以太网电缆RJ45连接到GWN7600LR正确的端口,并合上接口后盖。
5. 将GWN7600LR对准安装支架底座并自上而下卡入直至主机背面的定
位柱顶住底座。
6. 将2颗组合螺丝拧入主机背面的螺孔中，直至GWN7600LR牢牢固定
在安装支架上。
4
5
~10~
横杆安装
连接到GWN7600LR默认的无线网络
1. 将4个(PM8)螺丝插入安装支架后盖的四个螺丝孔中备用。
2. 将装有螺丝的安装支架后盖的凹槽对准将要安装GWN7600LR的横杆
并卡入。
3. 利用安装包内的防松螺母和（PM8）螺丝，将安装支架后盖和安装支
架底座组装起来。
3
1
4. 将以太网电缆RJ45连接到GWN7600LR正确的端口,并合上接口后盖。
5. 将GWN7600LR对准安装支架底座并自上而下卡入直至主机背面的定位
柱顶住底座。
6. 将2颗组合螺丝拧入主机背面的螺孔中，直至GWN7600LR牢牢固定在
安装支架上。
2
4
新的GWN7600LR会有默认的WiFi广播。 恢复出厂设置也能使默认WiFi
启动。
将GWN7600LR上电起机并连接至网络，GWN7600LR会广播默认的
SSID。该SSID是基于设备的MAC地址后六位： GWN[MAC后六位]，并
且使用随机的密码。
注意：GWN7600LR的默认SSID和随机密码打印在设备的MAC地址贴纸
上。
访问配置页面
将电脑连接到GWN7600LR广播的无线网，或GWN7600LR所在的局域
网。就可以用以下的几种方式来发现并访问GWN7600LR 的配置页面：
方法1：用MAC地址来发现GWN7600LR。
~11~
1. 在设备的背面的贴纸上，或者设备的外包装盒上可以找到设备的MAC
地址。
2. 在连接到GWN7600LR广播的无线网，或GWN7600LR所在的局域网
5
的电脑上，用浏览器输入网址：https://gwn_<mac>.local
比如：如果GWN7600LR的MAC地址为00:B8:8B:7E:7E:7E，那么则输入
https://gwn_00b88b7e7e7e.local
~12~
方法2：用GWNDiscoveryTool发现GWN7600LR。
1. 从下面的连接下载GWNDiscoveryTool: http://www.grandstream.
com/support/tools
2. 打开GWNDiscoveryTool，并点击Scan（扫描）。
3. 这个软件将帮助你发现局域网下所有的GWN7600LR并显示他们MAC
地址和IP地址。
4. 点击Manage Device（管理设备）后，你将被引导到GWN7600LR的
配置界面。或者也可以通过在浏览器中输入所查找到GWN7600LR的IP
地址。
使用上面所述的一种方法，你会看到一个登陆界面。在用户名和密码均
输入默认的”admin”，点击Sign in （登陆）。
备注 :
● 确认GWN7600LR并没有被配对到另一个GWN76XX无线AP，否则配
置界面将会显示设备已配对，导致无法登陆配置页面。
● 如果GWN7600LR已经被配对，请从它的配主那里解除配对，或者恢
复该设备的出厂设置。
● 遵守当地关于频带、发射功率及其他相关法规是每个用户的责任。
RESUMEN
Este punto de acceso Wi de largo alcance está diseñado para proporcionar soporte de cobertura extendida. Ideal para soluciones Wi en ex-
teriores gracias a su caja impermeable y tecnología resistente al calor. El
GWN7600LR viene equipado con tecnología MU-MIMO 2x2:2 de doble
banda con formación de haces y un sosticado diseño de antena para
máximo rendimiento de red y alcance de cobertura Wi extendida de
hasta 300 metros. Para garantizar la facilidad en su instalación y manejo,
el GWN7600LR emplea un diseño de gestión de redes distribuidas sin
controladores y un controlador integrado dentro de la interfaz de usuario
web del producto. Esto permite que cada punto de acceso gestione una
red de hasta 30 puntos de acceso GWN de manera independiente sin
necesitar hardware/software de controlador por separado y sin un punto
único de fallo. Su facilidad de instalación y manejo junto con el soporte
de cobertura adicional y las características avanzadas de rendimiento,
hacen del GWN7600LR un punto de acceso ideal para exteriores para
instalaciones de red inalámbrica de tamaño mediano.
PRECAUCIONES
● No intente abrir, desarmar o modicar el dispositivo
● No exponga este dispositivo a temperaturas fuera del rango de -30°C
a 60 °C en funcionamiento y desde -30 °C a 70 °C cuando se encuentre
almacenado.
● No exponga el GWN7600LR a entornos fuera del siguiente rango de
humedad: 5-95% RH (sin condensación).
● No apague su GWN7600LR durante el reinicio del sistema o actual-
ización de Firmware.Puede corromper la imagen del rmware y causar
un mal funcionamiento de la unidad.
CONTENIDO DEL PAQUETE
ES
欲获取详细的话机使用信息，请在以下链接中下载GWN7600LR用户手册。
http://www.grandstream.com/support
~13~
1 x GWN7600LR Punto
de Acceso
1 x Soporte de
Cubierta
~14~
1 x Soporte de Base
Paso 1: Conecte un cable Ethernet RJ45 en el puerto de red del GWN7600LR.
4 x Tornillos
(PM8 x 115)
2 x Tornillos de
Ensamblaje
4 x Tornillos y Anclajes
1 x Guía de instalación Rápida
1 x Declaración GPL
4 x Tuercas
de Bloqueo
PUERTOS GWN7600LR
Puerto Descripción
NET/POE Puerto Ethernet RJ45 (10/100/1000Mbps) con so-
porte de PoE/ PoE+.
NET Puerto Ethernet RJ45 (10/100/1000Mbps) para su
router u otro GWN7600LR.
RESET Botón de reinicio de fábrica. Presione por 7 segun-
dos para llevar a los ajustes de fábrica.
Paso 2: Conecte el otro extremo del cable en el puerto del switch (PoE).
Puerto de Red
Cable Ethernet RJ45
para Switch (PoE)
INSTALACIÓN DE HARDWARE
El GWN7600LR puede ser montado horizontal y verticalmente sobre una
barra de metal. Porfavor consulte los siguientes pasos para la apropiada
instalación.
Montaje Vertical
1. Prepare el soporte de cubierta insertando los 4 tornillos (PM8) dentro
de los oricios correspondientes
2. Fije el soporte de cubierta con los tornillos en el Perno de Montaje
vertical donde el GWN7600LR será instalado.
3. Monte el soporte base con el soporte de la cubierta utilizando las tuer-
cas de bloqueo y tornillos de jación (PM8) suministrados.
1
2
3
ENCENDIENDO Y CONECTANDO EL GWN7600LR
GWN7600LR puede ser alimentado usando un switch PoE por medio
de los siguientes pasos:
~15~
~16~
Loading...