Gorenje KAS35ININVDC, KAS21INTT, KAS26ININVDC, KAS35INTT, KAS26INTT User Manual

...

USERS AND INSTALLATION MANUAL UPUTE ZA UPORABU I POSTAVLJANJE UPUTE ZA UPORABU I POSTAVLJANJE UPUTE ZA UPORABU I POSTAVLJANJE ІНСТРУКЦІЇ З ВИКОРИСТАННЯ ТА МОНТАЖУ

НАСТЕННАЯ СПЛИТ СИСТЕМА КОНДИЦИОНИРОВАНИЯ ВОЗДУХА ИНСТРУКЦИЯ

Thank you very much for purchasing this Air Conditioner. Please read this use and installation instructions carefully before installing and using this appliance and keep this manual for future reference.

FRANÇAIS

NEDERLANDS

USERS AND INSTALLATION MANUAL

Thank you very much for purchasing this Air Conditioner. Please read these use and installation instructions carefully before installing and using this appliance and keep this manual for future reference.

ITALIANO

ESPAÑOL

DEUTSCH

FRANÇAIS

PORTUGUÊS

NEDERLANDS

РУССКИЙ ЯЗЫК

Safety introduction 1 Preparation before use 3 Safety precautions 4

Installation instructions Installation diagram

Select the installation locations

Indoor unit installation

Outdoor unit installation

Air purging

Maintenance

Protection

Troubleshooting

Identification of parts

Indoor unit 18 Outdoor unit

Display introduction

Remote controller operating instructions. See" remote controller instructions".

-1-

1. To guarantee the unit work normally, please read the manual carefully before

installation, and try to install strictly according to this manual.

2. Do not let air enter the refrigeration system or discharge refrigerant when moving the air conditioner.

3. Properly ground the air conditioner into the earth.

4. Check the connecting cables and pipes carefully, make sure they are correct and

firm before connecting the power of the air conditioner.

5. There must be an air-break switch.

6. After installing, the consumer must operate the air conditioner correctly according to this manual, keep a suitable storage for maintenance and moving of the air conditioner in the future.

7. Fuse of indoor unit: T3.15A 250VAC or T5A 250VAC. Please refer to the screen printing on the circuit board for the actual parameters, which must be consistent with the parameters on the screen printing.

8. The installation instructions for appliances that are intended to be permanently connected to fixed wiring and have a leakage current that may exceed 10 mA, must state that the installation of a residual current device (RCD) having a rated residual operating current not exceeding 30 mA is advisable.

9. Warning: Risk of electric shock can cause injury or death: Disconnect all remote electric power supplies before servicing.

10. The maximum length of the connecting pipe between the indoor unit and outdoor unit should be less than 5 meters. It will affect the efficiency of the air conditioner if the distance longer than that length.

11. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

12. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children must not play with the appliance. Cleaning and user maintenance must not be made by children without supervision.

13. The batteries in remote controller must be recycled or disposed of properly. Disposal of Scrap Batteries --- Please discard the batteries as sorted municipal waste at the accessible collection point.

14. If the appliance is fixed wiring, the appliance must be fitted with means for disconnection from the supply mains having a contact separation in all poles that provide full disconnection under over voltage category III conditions, and these means must be incorporated in the fixed wiring in accordance with the wiring rules. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

-2-

15. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

16. The appliance must be installed in accordance with national wiring regulations.

17. The air conditioner must be installed by professional or qualified persons.

18. The appliance must not be installed in the laundry.

19. Regarding to installation, please refer to section “Installation instructions”.

20. Regarding to maintenance, please refer to section “Maintenance”.

-3-

When charging refrigerant into the system, make sure to charge in liquid state, if the refrigerant of the appliance is R410A. Otherwise, chemical composition of refrigerant R410A inside the system may change and thus affect performance of

the air conditioner. According to the character of refrigerant (R410A, the value of GWP is 2088), the pressure of the tube is very high, so be sure to be careful when you install and repair the appliance.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

The air conditioner must be installed by a professional engineer. The temperature of refrigerant circuit will be high, please keep the

interconnection cable away from the copper tube.

Before using the air conditioner, be sure to check and preset as the following. Remote Controller presetting

Each time after the remote control is replaced with new batteries or is energized, remote control auto presetting heat pump. If the air conditioner you purchased is a Cooling Only one, heat pump remote controller can also be used.

Back-light function (optional)

Hold down any button of the remote controller for about 2 seconds, the back-light will be turned on. It will be turned off automatically after about 10 seconds.

Auto Restart Presetting

The air conditioner has Auto-Restart function. You can set or cancel this function when the air conditioner is running.

Hold down the emergency button (ON/OFF) for a few seconds, this function will be set if you

hear beep twice. If you just hear beep once, this function will be canceled.

This appliance is made of recyclable or re-usable material. Scrapping must be carried out in compliance with local waste disposal regulations. Before scrapping it, make sure to cut off the mains cord so that the appliance cannot be re-used. For more detailed information on handling and recycling this product, contact your local authorities who deal with the separate collection of rubbish or the shop where you bought the appliance.

SCRAPPING OF APPLIANCE

This appliance is marked according to the European Directive 2012/19/EC, Waste Electrical and Electronic Equipment (WEEE).

This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling.

Note

Preset

-4-

Symbols in this Use and Care Manual are interpreted as shown below.

Be sure not to do.

Pay attention to such a situation.

Grounding is essential.

Warning: Incorrect handling could

cause a serious hazard, such as death, serious injury, etc.

Use correct power supply in accordance with the rating plate requirement. Otherwise, serious faults or hazard may occur, or a fire may break out.

Keep the power supply circuit breaker or plug from dirt. Connect the power supply cord to it firmly and correctly, lest an electric shock or a fire break out due to insufficient contact.

Do not use the power supply circuit breaker or pull off the plug to turn it off during operation. This may cause a fire due to spark, etc.

It is harmful to your health if the cool air reaches you for a long time. It is advisable to let the airflow be directed to the entire room.

Prevent the air flow from reaching the gas burners and stove.

Do not touch the operation buttons when your hands are wet.

Never insert a stick or similar obstacle to the unit. Since the fan rotates at high speed, this may cause an injury.

Do not repair the appliance by yourself. If this is done incorrectly, it may cause an electric shock, etc.

Do not put any objects on the outdoor unit.

OFF

SMART MODE

TEMP.

SUPER

FAN SPE ED

TEMP.

FEEL SLEEP

It is the user's responsibility to make the appliance be grounded according to local codes or ordinances by a licensed technician.

CLOCK TIMER ON TI MER OFF

QUIET DIM MER EC ONO MY

Turn off the appliance by remote control first before cutting off power supply if malfunction occurs.

Do not knit, pull or press the power supply cord, lest the power supply cord be broken. An electric shock or fire is probably caused by a broken power supply cord.

OFF

-5-

Distance from wall

should be over 50mm

Distance from ceiling

should be over 200 mm

Distance from the obstacle should be over 3000mm.

Distance from the wall

should be over 50mm

Distance from floor should be

over 2500mm.

Distance from the obstacle should be over 500mm.

Air intake distance from

the wall should be over 250mm

Air intake distance from the wall

should be over 250mm

Above figure is only a simple presentation of the unit, it may not match the external appearance of the unit you purchased.

Installation must be performed in accordance with the national wiring standards by authorized personnel only.

over 250mm

Installation diagram

-6-

Location for Installing Indoor Unit

Where there is no obstacle near the air outlet and air can be easily blown to every corner. Where piping and wall hole can be easily arranged. Keep the required space from the unit to the ceiling and wall according to the installation diagram on the previous page. Where the air filter can be easily removed. Keep the unit and remote controller 1m or more away from television, radio etc. Keep as far as possible from fluorescent lamps. Do not put anything near the air inlet to obstruct it from air absorption. Install on a wall that is strong enough to bear the weight of the unit. Install in a place that will not increase operation noise and vibration. Keep away from direct sunlight and heating sources. Do not place flammable materials or combustion apparatuses on top of the unit.

Location for Installing Outdoor Unit

Where it is convenient to install and well ventilated. Avoid installing it where flammable gas could leak. Keep the required distance from the wall.

The pipe length between indoor and outdoor unit should be not more than 5 meters in factory default status, but it can go up to maximum 15 meters with additional refrigerant charge.

Keep the outdoor unit away from greasy dirt, vulcanization gas exit. Avoid installing it by the roadside where there is a risk of muddy water. A fixed base where it is not subject to increased operation noise. Where there is not any blockage of the air outlet. Avoid installing under direct sunlight, in an aisle or sideway, or near heat sources and ventilation fans. Keep away from flammable materials, thick oil fog, and wet or uneven places.

Model

Max. allowed pipe length without additional refrigerant (m)

Limit of pipe length (m)

Limit of Elevation Difference H (m)

Required amount of

additional refrigerant (g/m)

2kW~5,3kW

15 5

6kW~7,3kW

15 5

8,8kW~10kW

If the height or pipe length is out of the scope of the table, please consult the dealer.

-7-

1. Installing the Mounting Plate

Decide an installing location for the mounting plate according to the indoor unit location and piping direction. Keep the mounting plate horizontally with a horizontal ruler or dropping line.

Drill holes of 32mm in depth on the wall for fixing the plate.

Insert the plastic plugs to the hole, fix the mounting plate with tapping screws.

Inspect if the mounting plate is well fixed. Then drill a hole for piping.

Tapping screw

Mounting plate

Note: The shape of your mounting plate may be different from the one above, but the installation method is similar.

Note: As the above figure shows, the six holes matched with tapping screw on the mounting plate must be used to

fix the mounting plate, the others are prepared.

2. Drill a Hole for Piping

Decide the position of hole for piping according to the location of mounting plate.

Drill a hole on the wall. The hole should tilt a little downward toward outside.

Install a sleeve through the wall hole to keep the wall tidy and clean.

3. Indoor Unit Piping Installation

Put the piping (liquid and gas pipe) and cables through the wall hole from outside or put them through from inside after indoor piping and cables connection complete so as to connect to outdoor unit. Decide whether to saw the unloading piece off in accordance with the piping direction (as shown below).

Piping direction

trough

Unloading

piece

Saw the unloading piece

off along the trough

Note: When installing the pipe at the directions

1,2 or 4, saw the corresponding unloading piece

off the indoor unit base.

After connecting piping as required, install the drain hose. Then connect the power cords. After connecting, wrap the piping, cords and drain hose together with thermal insulation materials.

Indoor unit installation

-8-

Piping Joints Thermal Insulation:

Wrap the piping joints with thermal insulation materials and then wrap with vinyl tape.

Piping Thermal Insulation:

a. Place the drain hose under the piping. b. Insulation material uses polythene foam over 6mm in thickness.

Note: Drain hose is prepared by user.

Drain pipe should point downward for easy drain flow. Do not arrange the drain pipe twisted, sticking out or wave

around, do not immerse the end of it in water. If an extension drain hose is connected to the drain pipe, make sure to thermal insulated when passing along the indoor unit.

When the piping is directed to the right, piping, power cord, and drain pipe should be thermal insulated and fixed onto the back of the unit with a piping fixer.

Base

Piping fixer

Base

drain hose

large pipe

small pipe

Piping fixer

Base

drain hose

large pipe

small pipe

Hook here

A. Insert the pipe fixer to the slot.

B. Press to hook the pipe fixer onto the base.

Note: The unit of 5,3kW#,7kW#,10,5kW is bigger than the unit of 5,3kW#,7kW#,10,5kW

-9-

4. Connecting of the Cable Indoor Unit

Connect the power connecting cord to the indoor unit by connecting the wires to the terminals on the control board individually in accordance with the outdoor unit connection.

Note: For some models, it is necessary to remove the cabinet to connect to indoor unit terminal.

Outdoor Unit

1). Remove the access door from the unit by loosening the screw. Connect the wires to the terminals on the control board individually as the following.

2). Secure the power connecting cord onto the control board with cable clamp.

3). Reinstall the access door to the original position with the screw.

4) Use a recognized circuit breaker for 7kW model or above between the power source and the unit. A disconnecting device to adequately disconnected all supply lines must be fitted.

Caution:

1. Never fail to have an individual power circuit specifically for the air conditioner. As for the method of

wiring, refer to the circuit diagram posted on the inside of the access door.

2. Confirm that the cable thickness is as specified in the power source specification.

3.Check the wires and make sure that they are all tightly fastened after cable connection.

4. Be sure to install an earth leakage circuit breaker in wet or moist area.

Cable Specifications

Capacity

(kW)

Power cord

Power connecting cord

Power connecting cord1

Main power supply

Type

Normal cross

- sectional area

Type

Normal cross

- sectional area

Type

Normal cross

- sectional area

1,5 ~ 3,8

H05VV-F

0.75~1.5mm2X3

H07RN-F H05RN-F

1.5mm2X3

0.75~1.0mm2X3

H05RN-F

0.75mm2X2

(Heat-pump)

To indoor

4,1 ~ 7

H05VV-F

1.5~2.5mm2X3

H07RN-F

1.5~2.5mm2X3

H05RN-F

0.75mm2X2

(Heat-pump)

To indoor

5,3 ~ 8,8

H05VV-F

1.5~2.5mm2X3

H07RN-F

1.5~2.5mm2X4

H05RN-F

0.75mm2X2

(Heat-pump&Optional)

To indoor

5,3 ~ 8,8

H07RN-F

2.5mm2X3

H05RN-F H07RN-F

1.0mm2X3

1.0mm2X4Cooling only

H05RN-F

0.75mm2X3

(Heat-pump)

To outdoor

7 ~ 10,6

H07RN-F

2.5~4.0mm2X3

H05RN-F H07RN-F

0.75mm2X4

1.0mm2X4

H05RN-F

0.75mm2X2

(Heat-pump&Optional)

To outdoor

7 ~ 10,6

H07RN-F

1.5mm2X5

H05RN-F

0.75mm2X4

H05RN-F

0.75mm2X2

(Heat-pump)

To outdoor

The cord may be different from the list above. It may be used as the next list. And it can be larger. 0-6A, use 0.75mm2 or 18AWG. 0-10A, use 1mm2 or 16AWG. 0-16A, use 1.5mm2 or 14AWG. 0-20A, use 2.5mm2 or 14AWG. 0-25A, use 2.5mm2 or 12AWG. 0-32A, use 4mm2.

Front

Terminal

Cabine

Indoor

Chassi

Access door Terminal(ins

ide)

Outdoor unit

The figures in this manual are based on the external view of a standard model. Consequently, the shape may differ from that of the air conditioner you have selected.

-10-

Wiring Diagram

Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

Note: All the wires may be of different colors. The indicators ‘1L 2L 3L’ may be ‘4 5 6’ or others.

And the terminal may be different from the material object.

1,5kW~7kW Model

For above models, the power supply is connected from indoor unit. For these models, the ground wire may be connected to the electric box directly.

5,3kW~8,8kW Model

For above models, the power supply is connected from indoor unit. For these models, the ground wire may be connected to the electric box directly.

5,3kW~8,8kW Model

For these models, the power supply is connected from outdoor unit, with a circuit breaker.

-11-

Warning: Before obtaining access to terminals, all supply circuits must be disconnected.

Note: All the wires may be of different colors. The indicators ‘1L 2L 3L’ may be ‘4 5 6’ or others.

And the terminal may be different from the material object.

7kW~10,6kW Model

For these models, the power supply is connected from outdoor unit, with a circuit breaker. All the wires may be different colors.

Defrost cable (for heat-pump air conditioner only, and it`s an optional part)

After connection, the defrost wire should be well wrapped with a wrapping tape and the connector should be put inside the unit.

Overheat protection or high-pressure protection cable (it`s an optional part)

After connection, the wire should be well wrapped with a wrapping tape and the connector should be put inside the unit.

Ionizer (The ionizer is an optional part)

After connection, the ionizer will work automatically.

-12-

1. Install Drain Port and Drain Hose (for heat-pump model only)

The condensate drains from the outdoor unit when the unit operates in heating mode. In order not to disturb your neighbor and protect the environment, install a drain port and a drain hose to direct the condensate water. Just install the drain port and rubber washer to the chassis of the outdoor unit, then connect a drain hose to the port as the right figure shown.

2. Install and Fix Outdoor Unit

Fix with bolts and nuts tightly on a flat and strong floor. If installed on the wall or roof, make sure to fix the supporter well to prevent it from shaking due to serious vibration or strong wind.

3. Outdoor Unit Piping Connection

Remove the valve caps from the 2-way and 3-way valve.

Connect the pipes to the 2-way and 3-way valves separately according to the required torque.

4. Outdoor Unit Cable Connection (see previous page)

The air which contains moisture remaining in the refrigeration cycle may cause a malfunction on the compressor. After connecting the indoor and outdoor units, release air and moisture from the refrigerant cycle using a vacuum pump, as shown below.

Note: To protect the environment, be sure not to discharge the refrigerant to the air directly.

Outdoor unit installation

Air purging

Drain hose (prepared by user)

Rubber pad (optional)

Place under the leg pedestal

-13-

How to Purge Air Tubes: (1). Unscrew and remove caps from 2 and 3-way valves.

(2). Unscrew and remove cap from service valve. (3). Connect vacuum pump flexible hose to the service valve. (4). Start vacuum pump for 10-15 minutes until reaching a vacuum of 10 mm Hg absolutes. (5). With vacuum pump still running, close the low-pressure knob on vacuum pump manifold. Then

stop vacuum pump.

(6). Open 2-way valve 1/4 turn, then close it after 10 seconds. Check tightness of all joints using

liquid soap or an electronic leak detector.

(7). Turn 2 and 3-way valves stem to fully the valves. Disconnect vacuum pump flexible hose. (8). Replace and tighten all valve caps.

-14-

Dangerous!

Electric

shock!

Front panel maintenance

Cut off the power supply

Turn off the appliance first before disconnecting from power supply.

Grasp position "a" and pull outward to remove the front panel.

Wipe with a soft and dry cloth.

Use soft moisture cloth

Use a dry and

to clean if the front panel

soft cloth to

is very dirty;

clean it.

Never use volatile substance such as gasoline or polishing powder to clean the appliance.

Never sprinkle water onto the indoor unit

Reinstall and shut the front panel.

Reinstall and shut the front panel by pressing position "b" downward.

Air filter maintenance

Stop the appliance, cut off the power supply and remove the air filter.

1. Open the front panel.

2. Press the handle of the filter gently

from the front.

3. Grasp the handle and slide out the filter.

Clean and reinstall the air filter.

If the dirt is conspicuous, wash it with a solution of detergent in lukewarm water. After cleaning, dry well in shade.

Close the front panel again.

Clean the air filter every two weeks

if the air conditioner operates in an extremely dusty environment.

It is necessary to clean the air filter after using it for about 100 hours.

-15-

Operating condition

The protective device maybe trip and stop the appliance in the cases listed below.

*For Tropical (T3) Climate condition models, the temperature point is 55℃instead of 43℃. The temperature of some products is allowed beyond the range. In specific situation, please consult the dealer. If the air conditioner runs in COOLING or DRY mode with door or window opened for a long time when relative humidity is above 80%, dew may drip down from the outlet.

Noise pollution

Install the air conditioner at a place that can bear its weight in order to operate more quietly.

Install the outdoor unit at a place where the air discharge and the operation noise would not annoy

your neighbors.

Do not place any obstacles in front of the air outlet of the outdoor unit lest it increases the noise level.

Features of protector

1. The protective device will work at following cases.

Restarting the unit at once after operation stops or changing mode during operation, you need to wait for 3 minutes. Connect to power supply and turn on the unit at once, it may start 20 seconds later.

2. If all operation has stopped, press ON/OFF button again to restart. Timer should be set again if it has been canceled.

Features of HEATING mode

Preheat

At the beginning of the HEATING operation, the airflow from the indoor unit is discharged 2-5 minutes later.

Defrost

In HEATING operation, the appliance will defrost (de-ice) automatically to raise efficiency. This procedure usually lasts 2-10 minutes. During defrosting, fans stop operation. After defrosting completes, it returns to HEATING mode automatically.

Note: Heating is NOT available for cooling only air conditioner models.

HEATING

Outdoor air temperature is over 24oC

Outdoor air temperature is below -7oC

Room temperature is over 27oC

COOLING

Outdoor air temperature is over *43oC

Room temperature is below 21oC

DRY

Room temperature is below 18oC

-16-

The following cases may not always be a malfunction, please check it before asking for service.

Trouble

Does not run

Analysis

If the protector trip or fuse is blown. Please wait for 3 minutes and start again,

protector device may be preventing unit to work. . If batteries in the remote controller exhausted.

If the plug is not properly plugged.

No cooling or heating air

Is the air filter dirty? Are the intakes and outlets of the air

conditioner blocked？ Is the temperature set properly？

Ineffective control

If strong interference (from excessive static electricity discharge, power supply voltage abnormality) presents, operation will be abnormal. In such case, disconnect from the power supply and connect back 2-3 seconds later.

Does not operate immediately

don't run

Changing mode during operation, 3 minutes will delay.

Peculiar odor

This odor may come from another source such as furniture, cigarette etc., which is sucked in the unit and blows out with the air.

A sound of flowing water

Caused by the flow of refrigerant in the air conditioner, not a trouble.

Defrosting sound in heating mode.

Cracking sound is heard

The sound may be generated by the expansion or contraction of the front panel due to change of temperature.

Spray mist from

the outlet

Mist appears when the room air becomes very cold because of cool air discharged from indoor unit during COOLING or DRY operation mode.

The compressor indicator (red) lights on constantly, and indoor fan stops.

The unit is shifting from heating mode to defrost. The indicator will turn off within ten minutes and return to heating mode.

-17-

Identification of parts

Front Panel

Air Intake

Display Panel

Emergency Panel

Air Outlet

Vertical Adjustment

Louver

Horizontal Adjustment

Louver

Air Filter

Remote Controller

Air Intake

Pipes and Power

Connection Cord

Drain Hose

Note: Condensate water drains

at COOLING or DRY operation.

Air Outlet

Indoor unit

Outdoor unit

The figures in this manual are based on the external view of a standard model. Consequently, the shape may differ from that of the air conditioner you have selected.

-18-

Temperature indicator

Display set temperature. It shows FC after 200 hours of usage as reminder to clean the filter. After filter cleaning press the filter reset button located on the indoor unit behind the front panel in order to reset the display (optional).

Running indicator

Run

Timer

Sleep

Comp.

It lights up when the AC is running.

It flashes during defrosting.

Timer indicator

It lights up during set time.

Sleep indicator

It lights up in sleep mode.

Compressor indicator

It lights up when the compressor is on.

Super indicator

It lights up in super mode.

Mode indicator

Heating displays orange, others display white

Fan speed indicator

Signal Receptor

Smart WIFI indicator 10

It lights up during WIFI is on.

9 5 4 3 2

VG/VL series

-19-

4 2 1

VT series

5 4 3

SF/DG(Right side) series

1 2

4 2 1 5 3

SE series

-20-

NS/DE series

NT series

4 2 1 5 3

VQ/TE/TF/DA/DG(Middle)/DH/DL(Right side) series

-21-

VM series

3 5 1 2 4

4 5 1

NM/DF series

NK series

TA/TC series

TQ/TR series

optional

Timer

Comp.

Run

Sleep

The symbols may be different from these models, but the functions are similar.

SC series

SA/TD/TG/TS/DB/DC/DJ/DK/DL(Middle) series

Emergency button 11

To let the AC run or stop by pressing the button.

4 2 1 5 3

VC series

Timer

Comp.

Run

Sleep

UPUTSTVO ZA UPOTREBU I POSTAVLJANJE

Zahvaljujemo na kupovini ovog klima uređaja. Molimo da pre postavljanja i upotrebe uređaja pažljivo pročitate ovo uputstvo za postavljanje i

upotrebu, kao i da ga sačuvate za buduću upotrebu.

ITALIANO

ESPAÑOL

DEUTSCH

FRANÇAIS

PORTUGUÊS

NEDERLANDS

РУССКИЙ ЯЗЫК

Sadržaj

Bezbednosni saveti 1 Pre upotrebe 3 Mere opreza 4

Upustvo za postavljanje Prikaz postavljanja

Izaberite mesta postavljanja

Postavljanje unutrašnje jedinice

Postavljanje spoljašnje jedinice

Čišćenje vazduhom

Održavanje

Uklanjanje teškoća

Opis delova

Unutrašnja jedinica 18

Spoljašnja jedinica

Prikaz displeja

Za rukovanje daljinskim upravljačem pogledajte "uputstva za upotrebu daljinskog upravljača".

Sadržaj

-1-

1. Da biste obezbedili nesmetano funksionisanje uređaja, najpre pažljivo pročitate

uputstvo i striktno ga se pridržavate prilikom postavljanja uređaja.

2. Nemojte dozvoliti da vazduh prodre u rashladni sistem ili ispustite rashladno sredstvo dok pomerate klima uređaj.

3. Pravilno uzemljite klima uređaj.

4. Pažljivo proverite priključne kablove i creva i uverite su da su ispravni i

pričvršćeni pre nego što priključite klima uređaj na napon.

5. Mora postojati prekidač za isključenje vazduha.

Nakon postavljanja uređaja potrošač mora pravilno rukovati klima uređajem, u skladu sa ovim uputstvom, koje takođe mora odgovarjauće čuvati za

buduće održavanje i premeštanje klima uređaja.

6. Osigurač unutrašnje jedinice: T3.15 A 250 VAC ili T5 A 250 VAC. Za stvarne parametre pratite prikaz na natpisnoj pločici, koji moraju da budu u skladu sa parametrima na displeju.

7. U uputstvu za postavljanje uređaja namenjenih stalnom priključenju na

fiksno ožičenje sa strujom odvoda koja može da premaši 10 mA mora biti

navedeno da se preporučuje postavljanje uređaja za diferencijalnu zaštitu

(RCD) sa naznačenom preostalom radnom strujom koja ne prekoračuje 30 mA.

8. Upozorenje: opasnost od strujnog udara može da uzrokuje povrede ili smrt. Pre servisiranja isključite sve jedinice udaljenog napajanja električnom energijom.

9. Priključno crevo između unutrašnje i spoljašnje jedinice ne sme da bude duže od 5 metara. Veća dužina creva će da utiče efikasnost klima uređaja.

10. Ovaj uređaj ne smeju sa koriste osobe (uključujući i decu) sa smanjenim

fizičkim, senzornim ili duševnim sposobnostima, kao ni osobe sa

nedovoljnim iskustvom i znanjem, osim ako nisu dobili nadzor ili uputstvo za upotrebu uređaja od lica koje je odgovorno za njihovu bezbednost. Decu morate nadgledati da biste sprečili da se igraju uređajem.

11. Ovaj uređaj mogu da koriste deca starija od 8 godina i osobe sa

smanjenim fizičkim, senzornim ili duševnim sposobnostima, kao i osobe sa

nedovoljnim iskustvom i znanjem samo ako su na bezbedan način dobili nadzor ili uputstvo za upotrebu uređaja te razumeju uključene opasnosti.

Deca ne smeju da se igraju sa uređajem. Deca bez nadzora ne smeju da

obavljaju čišćenje ni korisničko održavanje .

12. Baterije iz daljinskog upravljača moraju pravilno da se odl ažu i recikliraju. Odlaganje otpadnih baterija --- Molimo da baterije odlažete odvojeno od komunalnog otpada na odgovarajućem mestu za sakupljanje.

13. Ako je uređaj namenjen stalnom priključenju na fiksno ožičenje, mora da

bude opremljen zaštitom za isključenje iz naponske mreže sa odvojenim

kontaktima na svim polovima, koja obezbeđuje potpuno isključenje pod uslovima prenaponske kategorije III i koja mora da bude ugrađena u fiksno ožičenje u skladu sa pravilima ožičenja.

Sadržaj

-2-

14. Ako je priključni kabl oštećen, mora ga zameniti proizvođač, ovlašćeni serviser, odnosno drugo kvlaifikovano lice, da bi se sprečila opasnost.

15. Uređaj mora da bude postavljen u skladu sa nacionalnim propisima od ožičenju.

16. Postavljanje klima uređaja mora da izvrši stručno, odnosno kvalifikovano osoblje.

17. Uređaj ne sme da bude postavljen u perionici veša.

18. Za postavljanje uređaja pratite poglavlje “Uputstvo za postavljanje”.

19. Za održavanje uređaja pratite poglavlje “Održavanje”.

Sadržaj

-3-

Podešavanje postavki unapred

Ako je za punjenje sistema rashladnim sredstvom predviđeno sredstvo R410A, napunite uređaj rashladnim sredstvom u tečnom stanju. U suprotnom bi mogao da se promeni hemijski sastav rashladnog sredstva R410A u unutrašnjosti sistema, što bi uticalo na rad klima uređaja.

S obzirom na simbol rashladnog sredstva (R410A – vrednost GWP je 2088),

pritisak cevi je veoma visok, zato budite pažljivi prilikom postavljanja i popravke

uređaja. Ako je priključni kabl oštećen, mora ga zameniti proizvođač, ovlašćeni serviser

ili drugo kvalifikovano lice, da bi se sprečila opasnost.

Klima uređaj mora da izvrši stručno, odnosno kvalifikovano osoblje.

Neka kabl za međusobno spajanje bude udaljen od bakarne cevi, jer će

temperatura kruga rashladnog srestva biti visoka.

Pre upotrebe klima uređaja proverite i podesite postavke unapred:

Svaki put kad stavite ili zamenite baterije u daljinskom upravljaču, automatski je podešeno daljinsko upravljanje toplotne pumpe. Ako je klima uređaj koji ste kupili namenjen samo hlađenju, takođe možete da koristite daljinski upravljač toplotne pumpe.

Funkcija osvetljenja pozadine (opciono)

Pritisnite bilo koji taster daljinskog upravljača u trajanju od oko 2 sekunde i uključiće se osvetljenje pozadine. Automatski će se isključiti nakon 10 sekundi.

Automatsko ponovno pokretanje postavki podešenih unapred

Klima uređaj ima funkciju automatskog ponovnog pokretanja. Tu funkciju možete da podesite ili poništite dok klima uređaj radi.

Pritisnite taster za zaustavljanje (ON/OFF) u trajanju od nekoliko sekundi i funkcija je podešena

ako čujete dvostruki zvučni signal. Ako čujete jednostruki zvučni signal, funkcija je poništena.

Ovaj uređaj je proizveden od materijala koji može da se reciklira, odnosno ponovo upotrebi. Odlaganje mora da bude izvršeno u skladu sa lokalnim propisima o zbrinjavanju otpada. Pre odlaganje proverite da li je mrežni kabl odrezan da biste sprečili ponovnu upotrebu uređaja. Za više informacija o postupanju i recikliranju ovog proizvoda obratite se lokalnim telima koja su nadležna za odvojeno sakupljanje otpada ili prodajnom mestu na kom ste kupili uređaj.

ODLAGANJE UREĐAJA

Ovaj uređaj je označen u skladu sa evropskom direktivom 2012/19/EC o otpadnoj električnoj i elektronskoj opremi (WEEE).

Ovaj simbol znači da se proizvod ne sme odlagati sa drugim kućnim otpadom i važi širom EU. Da biste sprečili štetu za životnu sredinu ili ljudsko

zdravlje zbog nekontrolisanog odlaganja otpada, reciklirajte ovaj proizvod i dajte svoj doprinos održivoj ponovnoj upotrebi materijalnih izvora. Za vrećanje starih proizvoda koristite sisteme sakupljanja i odlaganja ili se obratite prodajnom mestu na kom ste ih kupili. Oni mogu preuzeti ovaj proizvod u svrhu ekološki besprekornog recikliranja.

Napomena

+ 119 hidden pages