Godex EZPi-1200, EZPi-1300 User Manual

Download

Page 1

User’s Manual

EZPi-1000 Series

P/N. 920-013011-01 Rev. A, 08.2009

Page 2

FCC COMPLIANCE STATEMENT

FOR AMERICAN USERS

This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense.

EMS AND EMI COMPLIANCE STATEMENT

FOR EUROPEAN USERS

This equipment has been tested and passed with the requirements relating to electromagnetic compatibility based on the standards EN 55022:1998+A1:2000+A2:2003, CISPR 22 , Class A EN 55024:1998+A1:2001+A2:2003, IEC 61000- 4 Series EN 61000-3-2 / 2000 & EN 61000-3-3 /

1995. The equipment also tested and passed in accordance with the European Standard EN55022 for the both Radiated and Conducted emissions limits.

EZPi-1000 SERIES

TO WHICH THIS DECLARATION RELATES

IS IN CONFORMITY WITH THE FOLLOWING STANDARDS

EN55022 : 1998,CLSPR 22, Class A / EN55024 : 1998IEC 61000-4 Serial / EN61000-3-2 : 2000 / EN 6100-3-3 : 1995 / CFR 47, Part 15/CISPR 22 3rd Edition : 1997, Class A / ANSI C63.4 : 2001 / CNS 13438 / IEC60950-1 : 2001 / GB4943 : 2001 / GB9254 : 1998 / GB17625.1 : 2003 /EN60950-1 : 2001

CAUTION Danger of explosion if battery is incorrectly replaced Replace only with the equivalent type recommended by the manufacture. Dispose of used batteries according to the manufacturer’s instructions.

Only use with power supply adapter model: WDS060240P (9A). Changes or modifications not expressly approved by the party responsible for complian ce could

void the user's authority to operate the equipment.

Specifications are subject to change without notice. EZPi-1000 User’s Manual

Page 3

Safety Instructions

Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben.

1. Die Geräte nicht der Feuchtigkeit aussetzen.

2. Bevor Sie die Geräte ans Stromnetz anschließen, vergewissern Sie Sich, dass die Spannung des Geräts mit der Netzspannung übereinstimmt.

3. Nehmen Sie das Gerät bei Überspannungen (Gewitter) vom Netz. Das Gerät könnte sonst Schaden nehmen.

4. Sollte versehentlich Flüssigkeit in das Gerät gelangen, so ziehen sofort den Netzstecker. Anderenfalls besteht die Gefahr eines lebensgefährlichen elektrischen Schlags.

5. Wartungs- und Reparaturarbeiten dürfen aus Sicherheitsgründen nur von autorisierten Personen durchgeführt werden.

6. Bei Wartungs- und Reparaturarbeiten müssen die Sicherheitsvorschriften der zuständigen Berufsverbände und Behörden unbedingt eingehalten werden.

7. Bei Verletzungen unbedingt den Arzt aufsuchen und die gegebenenfalls die zuständigen Stellen benachrichtigen. Unterlassung kann zum Verlust der Versicherungsleistungen führen.

EZPi-1000 User’s Manual

Page 4

Safety Instructions

Please read the following instructions seriously.

1. Keep the equipment away from humidity.

2. Before you connect the equipment to the power outlet, please check the voltage of the power source.

3. Disconnect the equipment from the voltage of the power source to prevent possible transient over voltage damage.

4. Don’t pour any liquid to the equipment to avoid electrical shock.

5. ONLY qualified service personnel for safety reason should open equipment.

6. Don’t repair or adjust energized equipment alone under any circumstances. Some one capable of providing first aid must always be present for your safety

7. Always obtain first aid or medical attention immediately after an injury. Never neglect an injury, no matter how slight it seems.

EZPi-1000 User’s Manual

Page 5

1. BARCODE PRINTER...................................................................5

1-1. Printer Accessories.........................................................................................................5

1-2. General Specifications....................................................................................................5

1-3. Communication Interface................................................................................................7

1-4. Printer Parts....................................................................................................................9

2. PRINTER INSTALLATION......................................................... 11

2-1. Ribbon Installation ........................................................................................................11

2-2. Label Installation...........................................................................................................13

2-3. Label Roll Core Installation Instruction.........................................................................14

2-4. Card / Hang tags Installation ........................................................................................15

2-5. PC Connection..............................................................................................................15

2-6. Driver Installation.......................................................................................................... 16

3. CONTROL PANEL.....................................................................18

3-1. Control Panel Introduction............................................................................................18

3-2. Control Keys Introduction..............................................................................................18

3-3. Setting mode.................................................................................................................20

3-4. Self-Test........................................................................................................................ 24

3-5. Dump Mode .................................................................................................................. 25

3-6. Auto Sensing................................................................................................................. 25

3-7. Keyboard Mode.............................................................................................................26

3-8. Error Messages.............................................................................................................29

4. ACCESSORY............................................................................. 31

4-1. Stripper Installation....................................................................................................... 31

4-2. Cutter Installation..........................................................................................................34

4-3. WLAN Module Installation.............................................................................................36

4-4. CF Card Adapter Installation.........................................................................................40

4-5. CF Card Instruction....................................................................................................... 41

5. MAINTENANCE AND ADJUSTMENT....................................... 42

5-1. Thermal Print Head Cleaning ....................................................................................... 42

5-2. Thermal Print Head Balance Adjustment......................................................................42

5-3. Print Line Adjustment.................................................................................................... 43

5-4. Adjust the cutter............................................................................................................43

5-5. Troubleshooting............................................................................................................ 44

EZPi-1000 User’s Manual

Page 6

1. Barcode Printer

1-1. Printer Accessories

After unpacking, please check the accessories that come with the package, and store appropriately.

 Barcode printer  Power cord  Switching Power  USB Cable  Label  Ribbon  Empty Ribbon Roll  Label Roll Core  Label Stop Plate  Quick Start Guide  CD (includes label editing software QLabel / Manual)

1-2. General Specifications

Model EZPi-1200 EZPi-1300

Print Method

Thermal Transfer / Direct Thermal

Resolution

203 dpi (8 dot/mm) 300 dpi (12 dot/mm)

Print Speed

6 IPS (150 mm/s) 4 IPS (100 mm/s)

Print Width

4.25” (108 mm) 4.16” (105.7 mm)

Print Length

Min. 0.39” (10 mm); Max. 68” (1727 mm)

Min. 0.39” (10 mm); Max. 30” (762 mm)

Memory

4MB Flash (2MB for user storage) ; 8MB SDRAM

Sensor Type

Adjustable reflective sensor. Fixed transmissive sensor, central aligned

Media

Types: Continuous form, gap labels, black mark sensing, and punched hole; label length set by auto sensing or programming Width: 1” (25.4 mm) Min. - 4.64” (118 mm) Max. Thickness: 0.003” (0.06 mm) Min. - 0.01” (0.25 mm) Max. Label roll diameter: Max. 5” (127 mm) Core diameter: 1”, 1.5”, 3” (25.4 mm, 38.1 mm, 76.2 mm)

Ribbon

Types: Wax, wax/resin, resin Length: 981’ (300 m) Width: 1.18” Min - 4.33” (30 mm - 110 mm) Max Ribbon roll diameter.: 2.67“ (68 mm) Core diameter: 1” (25.4 mm)

Printer Language

EZPL, GEPL (Godex Eltron® Printer Language)

Software

Label design software: QLabel-IV (for EZPL only) Driver & DLL: Windows 2000, XP and Vista

Resident Fonts

Bitmap fonts: 6, 8, 10, 12, 14, 18, 24, 30, 16X26 and OCR A & B Bitmap fonts 90°, 180°, 270° rotatable, single characters 90°, 180°, 270° rotatable Bitmap fonts 8 times expandable in horizontal and vertical directions Scalable fonts 90°, 180°, 270° rotatable

Download Fonts

Bitmap fonts 90°, 180°, 270° rotatable, single characters 90°, 180°, 270° rotatable

sian fonts 90°, 180°, 270° rotatable and 8 times expandable in horizontal and vertical directions Scalable fonts 90°, 180°, 270° rotatable 1-D Bar codes: Code 39, Code 93, Code 128 (subset A, B, C), UCC/EAN-128 K-Mart, UCC/EAN-128, UPC A / E (add on 2 & 5), I 2 of 5, I 2 of 5 with Shipping Bearer Bars, EAN 8 / 13 (add on 2 & 5), Codabar, Post NET, EAN 128, DUN 14, HIBC, MSI (1 Mod 10), Random Weight, Telepen, FIM, China Postal Code, RPS 128 and GS1 DataBar

Barcodes

2-D Bar codes: PDF417, Datamatrix code, MaxiCode, QR code and Micro QR code

EZPi-1000 User’s Manual

Page 7

Code Pages

CODEPAGE 437, 850, 851, 852, 855, 857, 860, 861, 862, 863, 865, 866, 869, 737 WINDOWS 1250, 1251, 1252, 1253, 1254, 1255 Unicode (UTF8, UTF16)

Graphics

Resident graphic file types are BMP and PCX, other graphic formats are downloadable from the software

Interfaces

Serial port: RS-232 (DB-9) USB port (default on) Parallel port: Centronics 36-pin PS2 port CF Card socket Ethernet 10/100Mbps print server (default off; disables USB when in use)

Control Panel

Backlit graphics LCD display: 128 x 64 dots or 4 lines x 16 characters Three mono-color status-LEDs: Power on, Ribbon out, Media out Control keys: FEED, PAUSE and CANCEL

Real Time Clock

Standard

Power

Auto Switching 100-240VAC, 50-60Hz

Environment

Operation temperature: 41°F to 104°F (5°C to 40°C) Storage temperature: -4°F to 122°F (-20°C to 50°C)

Humidity

Operation: 30-85%, non-condensing. Storage: 10-90%, non-condensing.

Agency

Approvals

CE(EMC), FCC Class A, CB, cUL, CCC

Dimension

Length: 11.2” (285 mm) Height: 6.8” (171 mm) Width: 8.9” (226 mm)

Weight

6.6 lbs (3.0Kg) ,excluding consumables

Options

Rotary Cutter Label Stripper External label roll holder for 10” (250 mm) O.D. label rolls External label rewinder

802.11 b/g wireless print server (Default off; disables USB when in use. Must remove PS2 port and Ethernet card to install)

Specifications are subject to change without notice. All company and/or product names are trademarks and/or registered trademarks of their respective owners.

EZPi-1000 User’s Manual

Page 8

1-3. Communication Interface

Parallel Interface

Handshake : DSTB connects to the printer, BUSY connects to the host Interface cable : Parallel cable compatible to IBM PC Pin out : See below

PIN NO. FUNCTION TRANSMITTER 1 2-9 10 11 12 13 14 15 16 17 18 19-30 31 32 33 34-35 36

/Strobe Data 0-7 /Acknowledge Busy /Paper empty /Select /Auto-Linefeed N/C Signal Gnd Chasis Gnd +5V,max 500mA Signal Gnd /Initialize /Error Signal Ground N/C /Select-in

host / printer host printer printer printer printer host / printer

host host / printer printer

host / printer

Serial Interface

Serial Default Setting

9600 baud rate､no parity､8 data bits､1 stop bit､XON/XOFF protocol and RTS/CTS。

RS232 HOUSING (9-pin to 9-pin)

DB9 SOCKET DB9 PLUG

--- 1 1 +5V,max 500mA RXD 2 2 TXD TXD 3 3 RXD DTR 4 4 N/C GND 5 5 GND DSR 6 6 RTS RTS 7 7 CTS CTS 8 8 RTS

RI 9 9 N/C

PRINTER

【

Note】The total current output from parallel port and serial port altogether can not exceed

500mA.

USB Interface

Connector Type : Type B

PIN NO. 1 2 3 4

FUNCTION VBUS D- D+ GND

EZPi-1000 User’s Manual

Page 9

Internal Interface

UART1 wafer Ethernet module

N.C

TXD

RXD

TXD

CTS

RTS

GND

RTS

CTS

E_MD

RTS

CTS

E_RST

+5V

GND

+5V

UART2 wafer Expansion module

+5V

CTS

RTS

TXD

RXD

RTS

CTS

RXD

TXD

GND

EZPi-1000 User’s Manual

Page 10

1-4. Printer Parts

1. Cover Open Button

2. Top Cover

3. Label Roll Core

4. Ribbon Rewind Wheel

5. LCD Module Case

6. Printing Mechanism

7. Front Cover Piece

1. Ribbon Rewind Shaft + Empty Ribbon Roll

2. Locking Tenon (left/right)

3. CF Card Slot Cover

4. Print Head Pressure Adjustment Screw (left/right)

EZPi-1000 User’s Manual

Page 11

1. Ribbon Supply Shaft

2. Label Guide

3. Platen Roller

4. Print Line Adjustment Gear

5. Label Sensor

1. LCD Control Panel

2. Fan-Fold Label Insert

3. Connection Port for PS2 / Wireless LAN Antenna (Optional)

4. Power Switch

5. Ethernet Port

6. USB Port

7. Parallel Port

8. Serial Port (RS-232)

9. Power Socket

* The communication ports may vary depending on product types.

EZPi-1000 User’s Manual

Page 12

2. Printer Installation

This printer model has the following print modes: Thermal Transfer (TT) When printing, ribbon must be installed to transfer the print contents

onto the media.

Direct Thermal (DT) When printing, no ribbon is necessary; it only requires direct thermal

media. Please check which print mode you will use and then go into the Setting Mode to change the print mode setting if necessary.

2-1. Ribbon Installation

1. Place the printer on a

horizontal surface, and open the top cover by pressing the Cover Open Buttons on both sides.

2. Loosen and then lift the

upper print mechanism by pressing the locking tenons.

3. Place a new ribbon roll

onto the ribbon supply shaft.

EZPi-1000 User’s Manual

Page 13

4. Feed the ribbon from

the Ribbon Supply Shaft under the Print Head.

5. Wrap the ribbon around

the Ribbon Shaft and stick the ribbon onto the Empty Ribbon Roll Core.

6. Firmly close the upper

print mechanism.

EZPi-1000 User’s Manual

Page 14

2-2. Label Installation

1. Open the top cover by

pressing the Cover Open Buttons on both sides.

2. Insert the Label Roll

Core into the label roll.

3. Assemble the Label

Stop Plates on both sides of label roll.

4. Place the label roll into

the printer.

5. Loosen and lift the

upper print mechanism by pressing the locking tenons.

6. Feed the label through

the two Label Guides to the Tear-off Bar.

7. Align the label guides to

the edge of label.

8. Close the upper print

mechanism from the top to finish label installation.

EZPi-1000 User’s Manual

Page 15

2-3. Label Roll Core Installation Instruction

(A) 1” roll core installation

(B) 1.5” roll core installation

EZPi-1000 User’s Manual

Page 16

2-4. Card / Hang tags Installation

When installing cord tags, the tag hole must align with the sensor arrow (as indicated in figure), then use the Label Guide to secure the tags.

Sensor Detection Position

Sensor

2-5. PC Connection

1. Please make sure the printer is powered off.

2. Take the power cable, plug the cable switch to the power socket, and then connect the

other end of the cable to the printer power socket.

3. Connect the cable to the USB/parallel port on the printer and on the PC.

4. Power on the PC and the printer, then the printer’s LED light will start to flash.

EZPi-1000 User’s Manual

Page 17

2-6. Driver Installation

1. Insert product CD to your

computer’s CD Drive and find the "Windows Drives" folder.

2. Select the icon of driver file

and click it to start the installation.

3. Follow the instruction on

screen to keep the installation going. Then the Driver Wizard utility should run automatically.

4. Select "Install printer drivers".

5. Select printer model.

EZPi-1000 User’s Manual

Page 18

6. Select connection port.

7. Enter the printer name and

set printer sharing option.

8. A description page of printer

settings will be displayed after all settings are completed.

9. Check if all printer settings

are correct and then press Finish to start copying driver files.

10. Wait for file copying finished

and complete the installation.

11. After the driver installation is

complete, there should be a new printer model on Windows "Printer and Faxes" setting.

EZPi-1000 User’s Manual

Page 19

3. Control Panel

3-1. Control Panel Introduction

Control keys

FEED PAUSE

CANCEL

LED indicators

Power (Ready)

The Power (Ready) light is to indicate the power on status and the printer is ready to print.

Ribbon Ribbon status indication

Media Media status indication

3-2. Control Keys Introduction

FEED Key

After pressing the FEED key, printer will send the media (according to media type) to the specified stop position. When printing with continuous media, pressing the FEED key will feed media out to a certain length. When printing with gap labels, pressing the FEED key will feed one label at a time. If the label is not sent out to a correct position, please proceed to do the Auto Sensing (see page

25).

Pause Key

When pressing the Pause key in standby mode (ready to print), the printer will go into the Pause Mode, and LCD Display will indicate “Pause”. At this status, printer is not able to receive any command. Then pressing the Pause key once again, the printer will get out of the Pause mode and go back to standby mode.

Pressing the Pause key while printing, printer will suspend the print job. When the Pause key is pressed one more time, the printer will continue with the rest of the print job. For example, when printing with a print job that contains 10 labels and then press the Pause key to suspend the print job after 2 labels are printed out. If the Pause key is pressed again, the printer will print out remaining 8 labels to complete the print job.

Cancel Key

The Cancel key is used to cancel current print job. The LCD Display will show “Print job is cancelled” when pressing the Cancel key during printing. For example, when p rinting with a print job that contains 10 labels and then press the Cancel key after 2 labels are printed out. The remaining 8 labels will not be printed, and the printer goes back to standby mode.

EZPi-1000 User’s Manual

Page 20

With different combinations of FEED PAUSE and CANCEL keys, the printer can perform various functions as follows:

Item Key Beep LCD Message Description

Self test

+ Power

3 beeps Self test

Press and hold

key and turn on the printer until the buzzer beeps 3 times.

Dump mode

+ Power

3 beeps Æ 1 beep

Now in Dump

Mode

After entering Self test Mode, keep holding

key until the

buzzer beep once.

Auto

sensing

+ Power

3 beeps

Auto sensing

Mode

Press and hold

key and turn on the printer until the buzzer beeps 3 times.

Go to

default

+ +

Power on

2 beeps twice

Go to default

Press and hold

& keys and turn on the printer until the buzzer beeps 2 times. The printer setting will go to default.

Download

mode

+ Power

1 beep

DL MODE

Vx.xx

Press and hold

key and turn on the printer until the buzzer beeps once. This mode is only for firmware downloading.

Setting

mode

3 beeps Setting mode

When Power on, press and hold

key about 3 to 4 seconds

until the buzzer beep 3 times.

EZPi-1000 User’s Manual

Page 21

3-3. Setting mode

In the Setting Mode, changes can be made according to requirement on the printing mode, options, media type, and parallel interface (printer can only go into setting when connected to PC by parallel cable, USB cable, or serial cable).

1. Power on the printer and make sure it is on “Ready to print” status.

2. Press and hold Pause key about 3 to 4 seconds until the buzzer beep 3 times, and then the LCD will display “Setting Mode”.

3. In the Setting Mode, the keys have the following functions:

: MINUS / Enter

: MENU / NEXT

: PLUS / Exit

4. Before exiting the Setting mode, the LCD will prompt to ask whether save the settings or not. After user’s response on whether do or do not save the settings, printer will exit from Setting mode and return to standby mode.

Press and hold

key about 3 to 4 seconds until the buzzer beep 3 times and LCD shows

Setting mode. The LCD monitor will show different options on the bottom.

After entering to Setting mode, the first line on LCD display indicates the setting item and the second line is current value of setting.

Press "Enter" key to enter into one of setting item, the current setting value will be marked in black and other unselected values will be listed in normal font.

In adjustment type of setting items, the first line indicates the current item and the second line indicates current value.

Plus: press

key to increase the value

Minus: press

key to decrease the value

Next: press

key to go to next item

EZPi-1000 User’s Manual

Page 22

Below are general descriptions of setting items.

Darkness

Default: 15

Set the darkness of printing result. The setting value is from 0 to 19 and the default value is 15.

Speed

Set the speed of printing.

Adjust Stop Position

Default: 0

Set the stop position of printing. The setting value is from 0 to

10.

Printhead Position

Default: 0

Set the position of print head when printing. The setting value is from -100 to 100.

Printing mode

Default: Thermal Transfer Thermal Transfer:

when printing, a ribbon must be installed to transfer the print contents onto the media. Direct Thermal: when printing, no ribbon is necessary; it only requires direct thermal media.

Option Setup

Default: Option OFF Strip Mode:

turn on the stripper function

Cutter Mode: turn on the cutter function None: select this to turn off the stripper and cutter functions.

Sensor Setup

Default: Gap paper Black Mark: for label or plain paper with black mark in the

back Gap: for labels with liner and gap, or hang tags. The default is set to be gap paper.

Continuous: for continuous paper Baud Rate: Default - 9600 bits

4800 bits 9600 bits 19200 bits 38400 bits 57600 bits 115200 bits

Parity: Default - None Parity

None Parity Odd Parity Even Parity

Data Bits: Default - 8 bits

7 bits 8 bits

COM Port Set

Stop Bits: Default - 1 bit

1 bits 2 bits

Auto Sensor

Default: Auto Mode Auto Mode: auto sense the label type (black mark, gap &

plain paper) and length

Gap Mode: detects gap paper Black Mark Mode: detects black mark label

LCD Language

Default: English

English Simplified Chinese Traditional Chinese Spanish Italian Deutsch French Turkish

EZPi-1000 User’s Manual

Page 23

Code Page

Default: Code Page 850

Code Page850 Code Page852 Code Page437 Code Page860 Code Page863 Code Page865 Code Page857 Code Page861 Code Page862 Code Page855 Code Page866 Code Page737 Code Page851 Code Page869 Windows 1252 Windows 1250 Windows 1251 Windows 1253 Windows 1254 Windows 1255

Keyboard Setup

Default: US

US UK French German Spanish Italian Finnish Dutch Belgian

Keyboard Mode

Default: Recall Label Recall Label：Recall label from memory card.

Keyboard Setup：Setting the keyboard. Code page Setup：Setting the code page. Printing Option: Set the print quantity.

Clock Setup: Set the clock and clock display. Exit KB Mode：Exit PS2 KB Mode.

Buzzer Setup

Default: ON

ON OFF

Smart Backfeed

Default: ON ON: This function must install stripper or cutter. OFF

Password

Default: OFF ON: When password protect enable, the password is required

for entering Setting Mode.

OFF

Top of Form

Default: ON ON: Start each printing from the Top-of-Form position. OFF

USB / Ethernet

Default: USB USB: Set the USB port as active port. Ethernet: Set the Ethernet port as active port.

Preview

Preview and check all settings.

【

Note 1】“Default Setting” is the original settings from the factory, if other changes are made on

the settings, then follow the new settings.

【

Note 2】Printer will store the previous settings after power off, thus if settings are to be

changed again, please enter the Setting Mode to reset.

EZPi-1000 User’s Manual

Page 24

The diagram of Setting Mode

 To enter the Setting mode, please press and hold the Pause key about 3 to 4 seconds until

the buzzer beeps 3 times and LCD shows "Setting mode".

 Item with the ”＊" sign is default setting.

EZPi-1000 User’s Manual

Page 25

3-4. Self-Test

The Self-Test function will help user to check whether the printer is operating normally. The printer will go back to standby mode after printing a Self-Test page. Below are the Self-Test procedures:

1. Power off the printer, press and hold the FEED key.

2. Power on the printer while still holding the FEED key until the printer beeps 3 times and the LCD Display would show “Self Test”, and then release the FEED key.

3. After about 1 second, printer would automatically print out a Self-Test page as follow. This means the printer is working properly.

EZXXXX : VX.XXX Serial port :96,N,8,1 int-usb sw setting: ext-USB

1 DRAM installed Image buffer size : 1500K 000 FORM(S) IN MEMORY 000 GRAPHIC (S) IN MEMORY 000 FONT(S) IN MEMORY 000 ASIAN FONT(S) IN MEMORY 000 DATABASE(S) IN MEMORY 000 TTF(S) IN MEMORY 2048K BYTES FREE MEMORY ^S4 ^H19 ^R000 ~R200 ^W100 ^Q100,3 Option : ^D0 ^O0 ^AD See-through Volt: 4.8 3.7 2.4(2.3) Code Page: 850

Model & Version Serial port setup USB port setting

Test pattern Number of DRAM installed

Image buffer size Number of forms Number of graphics Number of fonts Number of Asian fonts Number of Databases Number of Scalable fonts Free memory size Speed, Density, Ref. Point, Print direction Label width, Form length Cutter, Stripper, Mode Sensor Setting Code Page

Self-Test includes the internal printer data setting.

EZPi-1000 User’s Manual

Page 26

3-5. Dump Mode

When the print result doesn’t match the label setting, it’s recommended to go into the Dump Mode to check whether there is a mistake in data transmission between the printer and the PC. For example, when printer receives 8 commands, yet without processing these commands, only printed out the contents of the commands, this will confirm whether the commands were received correctly. Test procedures to enter the Dump Mode are as follows:

1. Power off the printer, press and hold the FEED key.

2. Power on the printer (while still holding the FEED key).

3. When LCD Display shows “DUMP MODE BEGIN,” then release the FEED key. Printer will automatically print “DUMP MODE BEGIN.” This means the printer is already in Dump Mode.

4. Send commands to the printer, and check if printed content matches the commands that just be sent.

To cancel (get out of) the Dump Mode, please press the FEED key, and then the printer will automatically print “OUT OF DUMP MODE.” This indicates that the printer is back to the standby mode.

3-6. Auto Sensing

Printer can automatically detect the paper length and record it. By this way, users do not need to set the paper length and the printer can accurately detect the position of paper gap.

1. Check if the paper is loaded properly.

2. Power off the printer, press and hold the Pause key.

3. Power on the printer while still holding the Pause key until the printer beeps 3 times and the LCD Display shows “Auto Sensing mode,” then release the Pause key. The printer will automatically detect the label size/length and record the information.

4. LCD Display shows the results of measurement.

The printer will be back to standby mode after displaying the result of Auto Sensing.

EZPi-1000 User’s Manual

Page 27

3-7. Keyboard Mode

EZPi-1000 series printer can support keyboard with PS2 interface. To connect the PS2 keyboard, please do as follows:

1. Please be sure the printer power is on and is showing no error message.

2. Power off the printer and then plug the PS2 keyboard connector into the socket in the back

of printer.

3. Power on the printer, the message “Enter keyboard Mode [y/n]” will be displayed on the

LCD. Press FEED key on LCD control panel or press “Y” on PS2 keyboard to enter the Keyboard Mode.

While in the keyboard mode, you may press "Esc" key (or press CANCEL key on LCD panel) anytime to go back to the previous page, and at the end you will be prompted to exit the keyboard mode. When “Exit Keyboard Mode [y/n]” message is displayed on the LCD, enter “y” (or press FEED key on LCD panel) to leave the PS2 keyboard mode. To re-enter the keyboard mode, just restart the printer or select the "Keyboard mode" function in setting mode. To change the keyboard setting, please refer to the "Setting Mode diagram" in Chapter 3.3 .

Print a label with stored form in Keyboard Mode

^FTEST1 ^Q100,3 ^W100 ^H10 ^P1 ^S2 ^AD ^C1 ^R0 ~Q+0 ^O0 ^D0 ^E12 ~R200 ^L Dy2-me-dd Th:m:s C0,00001,+1,Serial Number V00,16,Product Name,jc0 V01,16,Price,jc0 AF,330,566,1,1,0,0,^C0 AH,212,168,1,1,0,0,^V00 AG,308,396,1,1,0,0,^V01 E

1. At least one label form has to be stored in printer before you can print with keyboard mode. To create a sample label form as above figure shows, please copy printing commands that listed on left column and send it to printer via QLabel or Hyper Terminal.

2. The sample label form includes 2 variables and 1 serial number: "Product name", "Price" and "Serial Number". The printing will not start until the values of 3 variables are provided.

3. Power off the printer, plug the connector of PS2 keyboard, and then power on the printer again.

4. Press “y “ to enter Keyboard mode

5. Press Enter to confirm the file selection

* Note: press either ↑ or ↓ can select previous or next label format

EZPi-1000 User’s Manual

Page 28

6. LCD will show the Serial Number Prompt.

7. Key in the start value. (Example:00001)

8. LCD will show the first Variable Prompt.

9. Key in the variable data. (Example: Apple)

10. LCD will show the second Variable Prompt.

11. Key in the variable data. (Example:

199)

12. LCD shows the Print quantity.

13. Key in the print quantity. (Example: 3)

EZPi-1000 User’s Manual

Page 29

14. The printer will print out 3 labels that include user-defined variables and serial number.

EZPi-1000 User’s Manual

Page 30

3-8. Error Messages

If problems occur that prevent the printer printing normally, the printer will beep as warning, and error messages will be displayed.

Quickly blinking

Slowly blinking Light is on

LED Message Light

LCD

Message

Display

Ribbon Media

Beep Description Solution

Print Head

is opened

both lights

are on

4 beeps

twice

Thermal Print Head is not firmly closed.

Re-open the Thermal Print Head and make sure it is closed tightly.

Entering

the

Cooling

Process

blinking

simultaneously

Thermal Print Head temperatur e high.

Printer goes back to standby mode after cooling.

Ribbon not installed, and printer shows error message.

Make sure the printer is in the Direct Thermal mode.

Out of

ribbon or

check

ribbon

sensor

3 beeps

twice

Ribbons used up or ribbon supply shaft not moving.

Replace with new ribbon roll.

Unable to detect paper.

Make sure the movable sensor mark is at the correct position, if the sensor is still unable to detect paper, and then go through Auto Sensing again.

Out of

media or

check

media gap

sensor

1 beep

twice

Label used up.

Replace with new label roll.

Check

paper

setting

1 beep

twice

Paper jam.

Possible causes: card tags, paper falling into the gap behind the platen roller, can’t find label gap/black mark, black mark paper out. Please adjust according to actual usage.

CF Card

not found

blinking

simultaneously

2 beeps

twice

CF Card is not formatted.

Please follow the instruction on Chapter 4-5 to format the CF Card.

EZPi-1000 User’s Manual

Page 31

Memory

Full

2 beeps

twice

Memory is full

Delete unnecessary data in the memory or use CF Card.

Filename

can not be

found

2 beeps

twice

Can’t find the file

Use “~X4” command to print out all the files, then check whether the file exist and the names are correct.

Filename

repeated

2 beeps

twice

File name is repeated

Change the file name and download again.

EZPi-1000 User’s Manual

Page 32

4. Accessory

4-1. Stripper Installation

1 Stripper Module 2 Screw (TAP 3*8) x 2pcs

【

Note1】 Please power off

the printer before installing the stripper module.

【

Note2】 Label liner thickness

is recommended to be 0.06mm ± 10% with basic weight 65g/

㎡

± 6%.

【

Note3】The max width for

stripper is 110mm

1. Open the top cover by pressing the Cover Open Buttons on both sides.

2. Loosen and then lift the upper print mechanism by pressing the locking tenons.

3. Unlock the front cover piece by pushing locks inward.

4. Lift/take off the front cover piece according to the direction shown in the figure.

EZPi-1000 User’s Manual

Page 33

5. Plug in the stripper connector onto the switchboard socket. (refer to right figure)

【

Note】

There are 2 sockets on the converting boards (one is for stripper installation, and another one is for cutter), before plug the connector into socket, please check the pin first.

6. Place the left side of the stripper first, and then fit the right side.

7. Hold the stripper module and tighten the screws.

8. Feed the label through the Label Guides.

【

Note】The label / paper used

for stripper is suggested to be at least 20mm in height.

【

Suggestion】When printing

with stripper module, it is suggested to set the stop position (^E) to 9.

9. Peel off the first label, and feed the liner through the roller and the Tear-off Bar.

EZPi-1000 User’s Manual

Page 34

10. Follow the direction as shown in figure to feed the liner across the stripper.

11. Close the upper print mechanism and the stripper.

12. Press the FEED key to adjust the position of label and complete the installation.

EZPi-1000 User’s Manual

Page 35

4-2. Cutter Installation

1 Cutter Module 2 Screw (TAP 3*8) x 2pcs

【

Note1】

Please power off the printer before installing the cutter module.

【

Note2】

Do not cut self-adhesive labels! The traces of adhesive will pollute the rotary knife and impair safe operation! The service life of the cutter is 500,000 cuts with 160g/

㎡

paper weight and 250,000 cuts with 200g/

㎡

paper

weight.

【

Note3】

The max paper cutting width is 116mm

【

Note4】

The label / paper that used for cutting is suggested to be at least 30mm in height.

1. Open the top cover by pressing the Cover Open Buttons on both sides.

2. Loosen and then lift the upper print mechanism by pressing the locking tenons.

3. Unlock the front cover piece by pushing locks inward.

4. Lift/take off the front cover piece according to the direction shown in the figure.

5. Plug in the cable connector of the cutter module onto the switchboard socket.

【

Note】

Before plug the connector into socket, please check the pin first.

EZPi-1000 User’s Manual

Page 36

6. Place the left side of the stripper first, and then fit the right side.

7. Flip the cutter module downward to open the cutter.

8. Hold the cutter module and lock it with screws

9. After the screws are locked, flip to close the cutter module.

10. Feed the label through the Label Guides.

11. Close the mechanism to complete the cutter module installation.

【

Note】

It is not suggested to use label-inside paper when printing with cutter module.

12. Press the FEED key to adjust the position of label and complete the installation.

【

Suggestion】

When printing with cutter module, it is suggested to set the stop position (^E) to 30.

EZPi-1000 User’s Manual

Page 37

4-3. WLAN Module Installation

1 Ethernet Cable 1.8M 2 Secure Screw*1 3 Bracket Screw*2 4 Module Bracket 5 WLAN module 6 Module Connection Wire

7 WLAN Antenna

8 Nut (for Antenna)

9 Washer (for Antenna) 10 Fixture Plate 11 Antenna Bracket

1. Make sure the power is off and the power cable is unplugged. Place the printer onto a smooth surface and flip the whole printer unit upside down.

2. Unscrew the screws as indicated in figure.

3. Press the Cover Open Button and open the top cover.

4. Remove the middle compartment and the top cover.

5. Unplug the Ethernet Module Connection Wire.

EZPi-1000 User’s Manual

Page 38

6. Unscrew the Ethernet Module Secure Screw.

7. Remove the Ethernet Module and its connection wire.

8. Unscrew the screw of PS2 Port with long-nose pliers

9. Unscrew the Ground Wire Screw and unplug the connection wire of PS2 Port to remove the PS2 Port.

10. Tighten the Ground Wire Screw.

11. Secure the WLAN module onto the bracket.

12. Cut the cable tie on the Module Connection Wire. Then Plug the connector into the socket on WLAN module.

【

Note】

Please cut the cable tie carefully. Do not damage the Module Connection Wire.

EZPi-1000 User’s Manual

Page 39

13. Align the WLAN module to the Ethernet port and plug into it.

14. Secure the module onto the back plate.

15. Thread the Module Connection Wire through the other connection wires on the mainboard as the direction showed in figure. Then arrange the Antenna Connection Wire as the arrow showed.

【

Note】

Please organize all cables and wires well before putting middle compartment and top cover back to ensure that the printer can be assembled correctly.

16. Thread Antenna Connection Wire through the hole on the Antenna Bracket. Then put the Antenna Connection Wire and Antenna Bracket on the Antenna port as figure showed.

EZPi-1000 User’s Manual

Page 40

17. Put the Fixture Plate first then the Washer and tighten the Nut to mount Antenna Connection Wire on the printer.

【

Note】

It is suggested to tighten the Nut with long-nose pliers when mounting the Antenna Connection Wire.

18. Turn the Antenna according to the direction as arrow showed to mount it on the Antenna Connection Wire. The angle of Antenna can be adjusted if needed.

19. To complete the installation, reassemble the middle compartment and tighten the screws onto the bottom of the printer, then put the top cover back.

【

Note1】

After the WLAN module installation is completed, please send the "^XSET,USBETHERNET,1" printer command to printer for activating the Ethernet connection function. Please mind that USB port will be deactivated once the Ethernet connection function is activated.

【

Note2】

The first time setting operation must be performed with Ethernet (wired) connection before you can access wireless network.

EZPi-1000 User’s Manual

Page 41

4-4. CF Card Adapter Installation

1 CF Card Adapter (Front) 2 CF Card Adapter (Back)

【

Note】

Please power off the printer before installing the CF Card Adapter.

1. Open the top cover by

pressing the Cover Open Buttons on both sides.

2. Take off the label roll

core.

3. Open and remove the

plastic cover from the inner base.

4. Check the

correspondent pins and sockets to plug the adapter card onto the main board.

【

Note】

Please make sure the sockets and the pins are match, otherwise the pins may get damaged.

5. Close the plastic cover.

EZPi-1000 User’s Manual

Page 42

4-5. CF Card Instruction

EZPi-1000 series printers can read the CF Card after installed the CF Card Adapter. If the built-in memory is insufficient for storing label formats, graphics or fonts, users can use CF Card as external memory to provide more memory space.

When using the CF card, please follow the instruction as below:

1. Please power off the printer before installing or removing CF Card from the card slot.

2. The CF Card cannot be used for printer’s external memory until it is formatted in FAT16. When the printer has detected that the CF card is not formatted in FAT16, it will beep 3 times and the Status led light will flash orange.

3. If user wants to format the CF Card, just press the “FEED” key, and then the printer will start to format the CF Card in FAT16. When the format is complete, the LED light will turn to green.

4. If choose not to format the CF Card, just open the Top Cover of printer and wait for the turn-on procedure complete.

5. After the format is complete, a file folder named “Godex” would be created automatically. This folder is for storing all the data from the printer, please don’t do any change on it.

6. The specification of CF Card that is supported by the printer is as follow:

z Compact Flash Type I z Compact Flash (CF) v1.4 specification z Capacity: 128MB ~ 1GB z File system: FAT16

EZPi-1000 User’s Manual

Page 43

5. Maintenance and Adjustment

5-1. Thermal Print Head Cleaning

Unclear printouts may be caused by dusty print head, ribbon stain or label liner glue. Therefore when printing, it’s necessary to keep the top cover closed. Also, check and prevent paper/label from being stained or dusty to ensure print quality and to prolong the print head life. Print head cleaning instructions are as follows:

1. Power-off the printer.

2. Open the top cover.

3. Take out the ribbon.

4. Open the print head by pressing the locking tenons.

5. If on the print head (see blue arrow) there’s label pieces or other stain, please use a soft cloth with industrial use alcohol to wipe away the stain.

【

Note1】

Weekly cleaning on the print head is recommended.

【

Note2】

When cleaning the print head with soft cloth, make sure there is no any metal or hard particles attached on it.

5-2. Thermal Print Head Balance Adjustment

When printing with different label materials or using different ribbon types, unbalanced print quality may occur due to the media material differences, thus it’s necessary to adjust the Thermal Print Head pressure.

1. Open the top cover.

2. Take out the ribbon.

3. Turning the print head adjustment screws slightly by screwdriver to increase or decrease print head pressure.

EZPi-1000 User’s Manual

Page 44

5-3. Print Line Adjustment

To get better printing balance and quality, use print head adjusting gear to adjust the contacting surface between print head and label.

1. When turning print head adjusting gear counter-clockwise (as arrow 1 shows), print head would move in the direction where arrow A shows.

2. When turning print head adjusting gear clockwise (as arrow 2 shows), print head would move in the direction where arrow B shows.

5-4. Adjust the cutter

1. A cutter-adjusting hole is present on the side of cutter (where A is pointing to).

2. The cutter will not work properly if there is a paper jam. Turn the power off and use a #M3 hexagon wrench inserted into the hole “A”, and then turn it counter-clockwise.

3. Power on the printer after clearing the paper jam, the cutter will reset automatically.

【

Note】

The label / paper used for cutting is suggested to be at least 30mm in height.

EZPi-1000 User’s Manual

Page 45

5-5. Troubleshooting

Problem Recommended Solution

Power on the printer, but the LED does not light up

♦ Check the power connector is plugged correctly

LED light turns red (power/status) after printing stops

♦ Check for soft ware setting or program command errors ♦ Replace with suitabl e label or ribbon ♦ Check if label or ribb on is all out ♦ Check if label is jammed/ta ngled up ♦ Check if mechanism is not closed(Thermal Print Head not

positioned correctly)

♦ Check if sensor is blocked by paper/label ♦ Check for abnormal cutter function or of no actions (if cutter

is installed) Printing started, but nothing was printed on the label

♦ Check if label is placed up side down or if label is not

suitable for the application

♦ Select the correct printer driver ♦ Select the correct label and print type

When printing, label is jammed/tangled up

♦ Clean the label jam, and if label is stuck on Thermal Print

Head, please remove it by using soft cloth with alcohol When printing, only part of the contents were printed

♦ Check if label or ribbon is stuck on the Thermal Print Head ♦ Check if application software has errors ♦ Check if start position setting has errors ♦ Check if ribbon has wrinkles ♦ Check if ribbon supply shaft is creating friction with the

platen roller. If the platen roller needs to be replaced,

please contact your reseller for more information

♦ Check if power supply is correct When printing, part of the label wasn’t printed completely

♦ Check if Thermal Print Head is stained or dusted

♦ Use internal command “~T” to check Thermal Print Head

can print completely

♦ Check the media quality Printout not in desired position

♦ Check if sensor is covered by paper or dust

♦ Check if liner is suitable for use, please contact reseller for

more information

♦ Check if label roll edge is aligned with Label Width Guide When printing, page skipping occurs

♦ Check if error occurs on la bel height setting

♦ Check if the sensor is cove red by dust

Unclear printout

♦ Check print darkness setting

♦ Check if Thermal Print Head is covered with glue or stain

When using cutter, label wasn’t cut straight

♦ Check if label is set up straight When using cutter, label

wasn’t cut successfully

♦ Check wheth er label thickness exceeds 0.2mm When using cutter, label

couldn’t feed or abnormal cutting occurs

♦ Check if the cutter is installed properly

♦ Check if the label is install ed prpperly

When using stripper, abnormal function occurs

♦ Check if stripper sen so r is covered with dust

♦ Check if label is installe d properly

【

Note】

Your dealer is knowledgeable about printers, printing software, and your unique system. Please contact your local dealer for further technical support.

EZPi-1000 User’s Manual