Gigabyte GA-Z97X-GAMING G1 WIFI-BK Manual

GA-Z97X-Gaming

G1 WIFI-BK

User's Manual

Rev. 1001

12ME-Z97G1BK-1001R

Motherboard

GA-Z97X-Gaming G1 WIFI-BK

Motherboard

GA-Z97X-Gaming G1 WIFI-BK

Mar. 21, 2014

Mar. 21, 2014

Copyright

© 2014 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.

The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer

Information in this manual is protected by copyright laws and is the property of GIGABYTE.

Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice.

No part of this manual may be reproduced, copied, translated, transmitted, or published in any form or by any means without GIGABYTE's prior written permission.

Documentation Classifications

In order to assist in the use of this product, GIGABYTE provides the following types of

documentations:

For quick set-up of the product, read the Quick Installation Guide included with the product.For detailed product information, carefully read the User's Manual.

For product-related information, check on our website at: http://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0" means the revision of the motherboard is 1.0. Check your motherboard revision before updating motherboard BIOS, drivers, or when looking for technical information.

Example:

Table of Contents

Box Contents....................................................................................................................			6
Optional Items..................................................................................................................			6
GA-Z97X-Gaming G1 WIFI-BK Motherboard Layout.......................................................			7
GA-Z97X-Gaming G1 WIFI-BK Motherboard Block Diagram..........................................			8
Chapter 1 Hardware Installation......................................................................................			9
1-1	Installation Precautions.....................................................................................		9
1-2	Product Specifications....................................................................................		10
1-3	Installing the CPU and CPU Cooler................................................................		13
1-3-1		Installing the CPU...................................................................................................	13
1-3-2 Installing the CPU Cooler........................................................................................			15
1-4	Installing the Memory......................................................................................		16
1-4-1 Dual Channel Memory Configuration......................................................................			16
1-4-2		Installing a Memory.................................................................................................	17
1-5	Installing an Expansion Card..........................................................................		18
1-6	Setting up AMD CrossFire™/NVIDIA® SLI™ Configuration...............................		19
1-7	Back Panel Connectors..................................................................................		20
1-8	Onboard Buttons, Switches, and LEDs..........................................................		22
1-9	Changing the Operational Amplifier................................................................		24
1-10	Internal Connectors........................................................................................		25
Chapter 2 BIOS Setup...................................................................................................			35
2-1	Startup Screen................................................................................................		36
2-2	The Main Menu...............................................................................................		37
2-3	M.I.T................................................................................................................		40
2-4	System Information.........................................................................................		52
2-5	BIOS Features................................................................................................		53
2-6	Peripherals......................................................................................................		57
2-7	Power Management........................................................................................		61
2-8	Save & Exit.....................................................................................................		63
Chapter 3 Configuring SATA Hard Drive(s)...................................................................			65
3-1	Configuring Intel® Z97 SATA Controllers.........................................................		65
3-2	Configuring Marvell® 88SE9172 SATA Controllers.........................................		77
3-3	Installing the SATA RAID/AHCI Driver and Operating System.......................		82

- 4 -

Chapter 4 Drivers Installation........................................................................................		89
4-1	Chipset Drivers...............................................................................................	89
4-2	Application Software.......................................................................................	90
4-3	Information......................................................................................................	90

Chapter 5 Unique Features...........................................................................................			91
5-1	BIOS Update Utilities......................................................................................		91
	5-1-1	Updating the BIOS with the Q-Flash Utility.............................................................	91
	5-1-2	Updating the BIOS with the @BIOS Utility..............................................................	94
5-2	APP Center.....................................................................................................		95
	5-2-1	EasyTune................................................................................................................	96
	5-2-2	System Information Viewer.....................................................................................	97
	5-2-3	EZ Setup.................................................................................................................	98
	5-2-4	Fast Boot...............................................................................................................	103
	5-2-5	Smart TimeLock....................................................................................................	104
	5-2-6	Smart Recovery 2.................................................................................................	105
	5-2-7	USB Blocker..........................................................................................................	107
	5-2-8	Smart Switch.........................................................................................................	108
	5-2-9	Cloud Station.........................................................................................................	109
	5-2-10	Game Controller....................................................................................................	115

Chapter 6 Appendix.....................................................................................................			117
6-1	Qualcomm® Atheros Killer Network Manager...............................................		117
6-2	Configuring Audio Input and Output..............................................................		118
	6-2-1	Configuring 2/5.1-Channel Audio..........................................................................	118
	6-2-2	Creative Software Suite........................................................................................	118
	6-2-3	Configuring S/PDIF Out........................................................................................	122
	6-2-4	Configuring Audio Recording................................................................................	123
	6-2-5 Using the Sound Recorder....................................................................................		125
6-3	Troubleshooting............................................................................................		126
	6-3-1	Frequently Asked Questions ................................................................................	126
	6-3-2	Troubleshooting Procedure...................................................................................	127
6-4	Debug LED Codes........................................................................................		129
Regulatory Statements............................................................................................			133
Contact Us...............................................................................................................			135

- 5 -

Box Contents

55 GA-Z97X-Gaming G1 WIFI-BK motherboard 55 Motherboard driver disk

55 User's Manual

55 Quick Installation Guide

55 Six SATA cables

55 I/O Shield

55 One 2-Way SLI bridge connector

55 One 3-Way SLI bridge connector

55 One 4-Way SLI bridge connector

55 One 2-Way CrossFire bridge connector 55 3.5" Front Panel with 2 USB 3.0/2.0 ports

55 One GC-WB867D-I (including one antenna, one USB 2.0 cable, driver disk, and user's manual)

The box contents above are for reference only and the actual items shall depend on the product package you obtain. The box contents are subject to change without notice.

Optional Items

2-port USB 2.0 bracket (Part No. 12CR1-1UB030-6*R)eSATA bracket (Part No. 12CF1-3SATPW-4*R)

3.5" Front Panel with 2 USB 3.0/2.0 ports (Part No. 12CR1-FPX582-2*R)HDMI-to-DVI adapter (Part No. 12CT2-HDMI01-1*R)

- 6 -

GA-Z97X-Gaming G1 WIFI-BK Motherboard Layout

PW_SW RST_SW

KB_MS_USB

ATX_12V_2X4

DVI

DP

R_USB30

HDMI

USB30_LAN2 Renesas® uPD720210

USB30_LAN1

LGA1150

Debug LED (Note)

CMOS SW

ATX

AUDIO

SYS_FAN1

PLX®

PEX8747

CPU_OPT

Intel® GbE

PCIEX16_1

CPU_FAN

TI Burr Brown®

LAN

OPA2134

PCIEX1_1

GA-Z97X-Gaming G1 WIFI-BK

CAP_SW2

CAP_SW1

PCIEX8_1

Qualcomm®

Atheros Killer

E2201 LAN

PCIEX1_2

PLX®

PEX8605

		USB30	ATX4P
		F
4 2	3 1		GSATA3
DDR3 DDR3	DDR3	DDR3		7 68
				9
Intel® Z97		Marvell®
		88SE9172

	PCIEX16_2
		B_BIOS	iTE®
Creative®	PCIEX1_3		Super I/O
Sound Core 3D		BBIOS_LED	BAT
		M_BIOS

PCIEX8_2 MBIOS_LED

Marvell® 88SE9172

SATA 3 1 0

CLR_CMOS

SATA_EXPRESS

SATA 3 3 2 5 4

SYS_

FAN2

BIOS_

SW

SYS

_FAN5

F_USB3

F_USB1

F_AUDIO

SYS_

FAN3

F_

USB2

SB

SYS_

FAN4

F_

PANEL

(Note) For debug code information, please refer to Chapter 6.

- 7 -

GA-Z97X-Gaming G1 WIFI-BK Motherboard Block Diagram

2 PCI Express x8				2 PCI Express x8					CPU CLK+/- (100 MHz)
					or		LGA1150			DDR3 1600/1333 MHz
	or									Dual Channel Memory
		x16			x16		CPU
		PCIExpress			PCIExpress					HDMI
									DisplayPort
		1			1					DVI
	x16					x16
								FDI
Switch		x16			x16	Switch	DMI2.0
PCIe CLK		PLX® PEX8747
(100 MHz)										1 SATA Express
		PCI Express Bus								or
										2 SATA 6Gb/s
3 PCI Express x1
			LAN1
						LAN2				4 SATA 6Gb/s
			RJ45
						RJ45
			Qualcomm®						Renesas		®
x1	x1	x1	Atheros Killer			Intel®	GbE		uPD720210 Hub
PLX® PEX8605			E2201 LAN			LAN					4 USB 3.0/2.0
					x1		x1			4 USB 3.0/2.0
							Intel® Z97
PCI Express Bus		x1				x1
PCIe CLK (100 MHz)		Marvell®			Marvell®					8 USB 2.0/1.1
		88SE9172		88SE9172
		2 SATA 6Gb/s		2 SATA 6Gb/s					Dual BIOS
									LPC Bus	iTE®
					Creative®					Super I/O
					Sound Core						PS/2 KB/Mouse
						3D
		Rear Speaker Out	Center/Subwoofer Speaker Out		Headphone/Speaker Out	Line Out MIC/Line In	S/PDIF Out
	For detailed product information/limitation(s), refer to "1-2 Product Specifications."
							- 8 -

Chapter 1 Hardware Installation

1-1 Installation Precautions

The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's manual and follow these procedures:

•• Prior to installation, make sure the chassis is suitable for the motherboard.

•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or warranty sticker provided by your dealer. These stickers are required for warranty validation.

•• Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components.

•• When connecting hardware components to the internal connectors on the motherboard, make sure they are connected tightly and securely.

•• When handling the motherboard, avoid touching any metal leads or connectors.

•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap, keep your hands dry and first touch a metal object to eliminate static electricity.

•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an electrostatic shielding container.

•• Before unplugging the power supply cable from the motherboard, make sure the power supply has been turned off.

•• Before turning on the power, make sure the power supply voltage has been set according to the local voltage standard.

•• Before using the product, please verify that all cables and power connectors of your hardware components are connected.

•• To prevent damage to the motherboard, do not allow screws to come in contact with the motherboard circuit or its components.

•• Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing.

•• Do not place the computer system on an uneven surface.

•• Do not place the computer system in a high-temperature environment.

•• Turning on the computer power during the installation process can lead to damage to system components as well as physical harm to the user.

•• If you are uncertain about any installation steps or have a problem related to the use of the product, please consult a certified computer technician.

- 9 -

Hardware Installation

1-2 Product Specifications

CPU	Support for Intel® Core™ i7 processors/Intel® Core™ i5 processors/
	Intel® Core™ i3 processors/Intel® Pentium® processors/Intel® Celeron® processors

in the LGA1150 package

(Go to GIGABYTE's website for the latest CPU support list.)

L3 cache varies with CPU

Chipset		Intel® Z97 Express Chipset
Memory		4 x DDR3 DIMM sockets supporting up to 32 GB of system memory
		* DuetoaWindows32-bitoperatingsystemlimitation,whenmorethan4GBofphysical
		memory is installed, the actual memory size displayed will be less than the size of
		the physical memory installed.

Dual channel memory architecture

Support for DDR3 1600/1333 MHz memory modules

Support for non-ECC memory modules

Support for Extreme Memory Profile (XMP) memory modules

(GotoGIGABYTE'swebsiteforthelatestsupported memoryspeedsandmemory modules.)

Onboard		Integrated Graphics Processor:
Graphics		-	1 x DVI-I port, supporting a maximum resolution of 1920x1200@60Hz
		-	1 x HDMI port, supporting a maximum resolution of 4096x2160@24Hz or
			2560x1600@60Hz
			* Support for HDMI 1.4a version.
		-	1 x DisplayPort, supporting a maximum resolution of 4096x2160@24Hz or
			3840x2160@60Hz
			* Support for DisplayPort 1.2 version.
		-	Support for up to 3 displays at the same time
		-	Maximum shared memory of 1 GB
Audio		Creative® Sound Core 3D chip
	TI Burr Brown® OPA2134 operational amplifier
	Support for Sound Blaster Recon3Di
	High Definition Audio
		2/5.1-channel
	Support for S/PDIF Out
LAN		1 x Qualcomm® Atheros Killer E2201 chip (10/100/1000 Mbit) (LAN1)
	1 x Intel® GbE LAN phy (10/100/1000 Mbit) (LAN2)
			* Teaming is not supported.
Wireless		Wi-Fi 802.11 a/b/g/n/ac, supporting 2.4/5 GHz Dual-Band
Communication		Bluetooth 4.0, 3.0+HS, 2.1+EDR
module		Support for 11ac wireless standard and up to 867 Mbps data rate
			* Actual data rate may vary depending on environment and equipment.
Expansion Slots		2 x PCI Express x16 slots, running at x16 (PCIEX16_1~2)
			* Foroptimumperformance,ifonlyonePCIExpressgraphicscardistobeinstalled,be
			sure to install it in the PCIEX16_1 slot; if you are installing two PCI Express graphics
			cards, it is recommended that you install them in the PCIEX16_1 and PCIEX16_2
			slots.

Hardware Installation

- 10 -

Expansion Slots 2 x PCI Express x16 slots, running at x8 (PCIEX8_1~2)

*The PCIEX8_1 slot shares bandwidth with the PCIEX16_1 slot and the PCIEX8_2 slot with PCIEX16_2. The PCIEX16_1/PCIEX16_2 slot will operate at up to x8 mode when the PCIEX8_1/PCIEX8_2 is populated.

(All PCI Express x16 slots conform to PCI Express 3.0 standard.)

3 x PCI Express x1 slots

(The PCI Express x1 slots conform to PCI Express 2.0 standard.)

Multi-Graphics		Support for 4-Way/3-Way/2-Way AMD CrossFire™/NVIDIA® SLI™ technology
Technology
Storage Interface		Chipset:
		-	1 x SATA Express connector
		-	6 x SATA 6Gb/s connectors (SATA3 0~5)
		-	Support for RAID 0, RAID 1, RAID 5, and RAID 10
			(SATA Express and SATA3 4/5 connectors can only be used one at a time.)
		2 x Marvell® 88SE9172 chips:
		-	4 x SATA 6Gb/s connectors (GSATA3 6~9)
		-	Support for RAID 0 and RAID 1
USB		Chipset:
		-	4 x USB 3.0/2.0 ports (2 ports on the back panel, 2 ports available through
			the internal USB header)
		-	8 x USB 2.0/1.1 ports (2 ports on the back panel, 6 ports available through
			the internal USB headers)
		Chipset + Renesas® uPD720210 USB 3.0 Hub:
		-	4 x USB 3.0/2.0 ports on the back panel

Internal

Connectors

1 x 24-pin ATX main power connector1 x 8-pin ATX 12V power connector1 x PCIe power connector

1 x SATA Express connector10 x SATA 6Gb/s connectors1 x CPU fan header

1 x water cooling fan header (CPU_OPT)

5 x system fan headers1 x front panel header

1 x front panel audio header1 x USB 3.0/2.0 header

3 x USB 2.0/1.1 headers1 x Clear CMOS jumper1 x power button

1 x reset button

1 x Clear CMOS button

2 x audio gain control switches

8 x onboard voltage measurement points2 x BIOS switches

Back Panel

Connectors

1 x PS/2 keyboard/mouse port1 x optical S/PDIF Out connector1 x DVI-I port

1 x DisplayPort1 x HDMI port

- 11 -

Hardware Installation

Back Panel

Connectors

2 x USB 2.0/1.1 ports6 x USB 3.0/2.0 ports2 x RJ-45 ports

5 x audio jacks (Center/Subwoofer Speaker Out, Rear Speaker Out, Line In/Mic In, Line Out, Headphone)

I/O Controller

iTE® I/O Controller Chip

Hardware

Monitor

System voltage detection

CPU/System/Chipset temperature detectionCPU/CPU OPT/System fan speed detectionCPU/System overheating warning

CPU/CPU OPT/System fan fail warningCPU/CPU OPT/System fan speed control

*Whether the fan speed control function is supported will depend on the cooler you install.

	BIOS		2 x 128 Mbit flash
		Use of licensed AMI UEFI BIOS
		Support for DualBIOS™
		PnP 1.0a, DMI 2.7, SM BIOS 2.7, ACPI 2.0
	Unique Features		Support for APP Center
				* Available applications in APP Center may differ by motherboard model. Supported
				functions of each application may also differ depending on motherboard
				specifications.
			-	@BIOS
			-	EasyTune
			-	EZ Setup
			-	Fast Boot
			-	Game Controller
			-	Cloud Station
			-	ON/OFF Charge
			-	Smart TimeLock
			-	Smart Recovery 2
			-	System Information Viewer
			-	USB Blocker
			Support for Q-Flash
		Support for Smart Switch
		Support for Xpress Install
	Bundled		Norton® Internet Security (OEM version)
	Software		Intel® Rapid Start Technology
		Intel® Smart Connect Technology
		Intel® Smart Response Technology
	Operating	Support for Windows 8.1/8/7
	System
	Form Factor		ATX Form Factor; 30.5cm x 24.4cm

*GIGABYTE reserves the right to make any changes to the product specifications and product-related information without prior notice.

*Please visit the Support & Downloads\Utility page on GIGABYTE's website to check the supported operating system(s) for the software listed in the "Unique Features" and "Bundled Software" columns.

Hardware Installation

- 12 -

1-3	Installing the CPU and CPU Cooler
	Read the following guidelines before you begin to install the CPU:
	••	Make sure that the motherboard supports the CPU.
		(Go to GIGABYTE's website for the latest CPU support list.)
	••	Always turn off the computer and unplug the power cord from the power outlet before installing the
		CPU to prevent hardware damage.
	••	Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly. (Or you may
		locate the notches on both sides of the CPU and alignment keys on the CPU socket.)
	••	Apply an even and thin layer of thermal grease on the surface of the CPU.
	••	Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
		of the CPU may occur.
	••	Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
		that the system bus frequency be set beyond hardware specifications since it does not meet the
		standard requirements for the peripherals. If you wish to set the frequency beyond the standard
		specifications, please do so according to your hardware specifications including the CPU, graphics
		card, memory, hard drive, etc.

1-3-1 Installing the CPU

A. Locate the alignment keys on the motherboard CPU socket and the notches on the CPU.

LGA1150 CPU Socket

Alignment Key

Alignment Key

Pin One Corner of the CPU Socket

	LGA1150 CPU
Notch	Notch

Triangle Pin One Marking on the CPU

- 13 -

Hardware Installation

B. Follow the steps below to correctly install the CPU into the motherboard CPU socket.

•• Before installing the CPU, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the CPU.

•• To protect the socket contacts, do not remove the protective plastic cover unless the CPU is inserted into the CPU socket. Save the cover properly and replace it if the CPU is removed.

Step 1:

Gently press the CPU socket lever handle down and away from the socket with your finger. Then completely lift the CPU socket lever and the metal load plate/plastic cover will be lifted as well.

Step 3:

Once the CPU is properly inserted, carefully replace the load plate. When replacing the load plate, make sure the front end of the load plate is under the shoulder screw. Then press the CPU socket lever. The protective plastic cover may pop off from the load plate during the process of engaging the lever. Remove the cover. (Save the cover properly and always replace it when the

CPU is not installed.)

Step 2:

Hold the CPU with your thumb and index fingers. Align the CPU pin one marking (triangle) with the pinonecorneroftheCPUsocket(oryoumayalign the CPU notches with the socket alignment keys) and gently insert the CPU into position.

Step 4:

Finally, secure the lever under its retention tab to complete the installation of the CPU.

NOTE:

Hold the CPU socket lever by the handle, not the lever base portion.

Hardware Installation

- 14 -

1-3-2 Installing the CPU Cooler

Follow the steps below to correctly install the CPU cooler on the motherboard.

Step 1:

Apply an even and thin layer of thermal grease on the surface of the installed CPU.

Step 3:

Place the cooler atop the CPU, aligning the four push pins through the pin holes on the motherboard. Push down on the push pins diagonally.

						Male
Direction of						Push Pin
the Arrow Sign						The Top
on the Male
						of Female
Push Pin
						Push Pin
						Female
						Push Pin

Step 2:

Before installing the cooler, note the direction of the arrow signonthemalepushpin.(Turningthe push pin along the direction of arrow is to remove the cooler, on the contrary, is to install.)

Step 4:

You should hear a "click" when pushing down each push pin. Check that the Male and Female push pins are joined closely.

(Refer to your CPU cooler installation manual for instructions on installing the cooler.)

Step 5:

After the installation, check the back of the motherboard. If the push pin is inserted as the picture above shows, the installation is complete.

Step 6:

Finally, attach the power connector of the CPU cooler to the CPU fan header (CPU_FAN) on the motherboard.

Use extreme care when removing the CPU cooler because the thermal grease/tape between the CPU cooler and CPU may adhere to the CPU. Inadequately removing the CPU cooler may damage the CPU.

- 15 - Hardware Installation

1-4 Installing the Memory

Read the following guidelines before you begin to install the memory:

•• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.

(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)

•• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.

•• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.

1-4-1 Dual Channel Memory Configuration

This motherboard provides four DDR3 memory sockets and supports Dual Channel Technology. After the memory is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling

Dual Channel memory mode will double the original memory bandwidth.

The four DDR3 memory sockets are divided into two channels and each channel has two memory sockets as following:

Channel A: DDR3_2, DDR3_4Channel B: DDR3_1, DDR3_3

Dual Channel Memory Configurations Table

	DDR3_4 DDR3_2		DDR3_3	DDR3_1
Two Modules	- -	DS/SS	- -	DS/SS
	DS/SS	- -	DS/SS	- -
Four Modules	DS/SS	DS/SS	DS/SS	DS/SS

(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)

DDR3_1

DDR3_3

DDR3_2

DDR3_4

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.

1.Dual Channel mode cannot be enabled if only one DDR3 memory module is installed.

2.When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of the same capacity, brand, speed, and chips be used and installed in the same colored DDR3 sockets. For optimum performance, when enabling Dual Channel mode with two memory modules, we recommend that you install them in the DDR3_1 and DDR3_2 sockets.

Hardware Installation

- 16 -

1-4-2 Installing a Memory

Before installing a memory module, make sure to turn off the computer and unplug the power cord from the power outlet to prevent damage to the memory module. DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs. Be sure to install DDR3 DIMMs on this motherboard.

Notch

DDR3 DIMM

ADDR3 memory module has a notch, so it can only fit in one direction. Follow the steps below to correctly install your memory modules in the memory sockets.

Step 1:

Note the orientation of the memory module. Spread the retaining clip at the right end of the memory socket. Place the memory module on the socket. As indicated in the picture on the left, place your fingers on the top edge of the memory, push down on the memory and insert it vertically into the memory socket.

Step 2:

The clip at the right end of the socket will snap into place when the memory module is securely inserted.

- 17 -

Hardware Installation

1-5 Installing an Expansion Card

Read the following guidelines before you begin to install an expansion card:

•• Make sure the motherboard supports the expansion card. Carefully read the manual that came with your expansion card.

•• Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage.

PCI Express x1 Slot

PCI Express x16 Slot

Follow the steps below to correctly install your expansion card in the expansion slot.

1.Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.

2.Align the card with the slot, and press down on the card until it is fully seated in the slot.

3.Make sure the metal contacts on the card are completely inserted into the slot.

4.Secure the card's metal bracket to the chassis back panel with a screw.

5.After installing all expansion cards, replace the chassis cover(s).

6.Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your expansion card(s).

7.Install the driver provided with the expansion card in your operating system.

Example: Installing and Removing a PCI Express Graphics Card:

•• Installing a Graphics Card:

Gently push down on the top edge of the card until it is fully inserted into the PCI Express slot. Make sure the card is securely seated in the slot and does not rock.

•• Removing the Card:

Gently push back on the lever on the slot and then lift the card straight out from the slot.

Hardware Installation

- 18 -

1-6 Setting up AMD CrossFire™/NVIDIA® SLI™ Configuration

A.System Requirements

-- Windows 8.1/8/7 operating system

-- A CrossFire/SLI-supported motherboard with two or more PCI Express x16 slots and correct driver -- CrossFire/SLI-ready graphics cards of identical brand and chip and correct driver

(Current GPUs that support 3-Way/4-Way CrossFire technology include the ATI Radeon™ HD 3800, HD 4800, HD 5800 series, and AMDRadeon™ HD 6800, HD 6900, HD 7800, and HD 7900 series. Current GPUs that support 3-Way/4-Way SLI™ technology include the NVIDIA 8800 GTX, 8800 Ultra, 9800 GTX,

GTX 260, GTX 280, GTX 470, GTX 480, GTX 570, GTX 580, GTX 590, and GTX 600 series.) For the latest GPU support information, please refer to the AMD/NVIDIA® website.)

-- CrossFire (Note)/SLI bridge connectors

-- A power supply with sufficient power is recommended (Refer to the manual of your graphics cards for the power requirement)

B.Connecting the Graphics Cards

Step 1:

Observe the steps in "1-5 Installing an Expansion Card" and install CrossFire/SLI graphics cards on the PCI

Express x16 slots. (To set up a 2-Way configuration, we recommend installing the graphics cards on the PCIEX16_1 and PCIEX16_2 slots.)

Step 2:

Insert the CrossFire (Note)/SLI bridge connectors in the CrossFire/SLI gold edge connectors on top of the cards.

Step 3:

Plug the display cable into the graphics card on the PCIEX16_1 slot.

C. Configuring the Graphics Card Driver

C-1. To Enable CrossFire Function

After installing the graphics card driver in the operating system,

go to the Catalyst Control Center. Browse to Performance\ AMD CrossFireX™ Configuration and ensure the Enable

CrossFireX™ check box is selected. If your system has more than two CrossFire cards, select the GPU combination you want to use and click Apply. (Available combination options are dependent on the number of graphics cards.)

C-2. To Enable SLI Function

After installing the graphics card driver in the operating system, go to the NVIDIA Control Panel. Browse to the ConfigureSLI,Surround,

PhysX screen and ensure Maximize 3D performance is enabled.

(Note) The bridge connector(s) may be needed or not depending on your graphics cards.

•Procedure and driver screen for enabling CrossFire/SLI technology may differ by graphics cards and driver version.

Refer to the manual that came with your graphics cards for more information about enabling CrossFire/SLI technology.

• When two or more graphics cards are installed, we recommend that you connect the SATA power cable from the power supply to the ATX4P connector to ensure system stability.

- 19 -

Hardware Installation

1-7 Back Panel Connectors

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. You can connect a USB DAC to this port or use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.

PS/2 Keyboard/Mouse Port

Use this port to connect a PS/2 mouse or keyboard.

DVI-I Port

The DVI-I port conforms to the DVI-I specificationand supports a maximum resolution of 1920x1200@60 Hz (the actual resolutions supported depend on the monitor being used). Connect a monitor that supports DVI-I connection to this port.

DisplayPort

DisplayPort delivers high quality digital imaging and audio, supporting bi-directional audio transmission. DisplayPort can support both DPCP and HDCP content protection mechanisms. You can use this port to connect your DisplayPort-supported monitor. The maximum supported resolution is 4096x2160@24Hz or 3840x2160@60Hz, but the actual resolutions supported are dependent on the monitor being used.

After installing the DisplayPort device, make sure the default device for sound playback is the

DisplayPort device. (The item name may differ from operating system. Refer to the HDMI settings information on the previous page for the configuration dialog box.)

USB 3.0/2.0 Port

The USB 3.0 port supports the USB 3.0 specification and is compatible to the USB 2.0/1.1 specification. Use this port for USB devices such as a USB keyboard/mouse, USB printer, USB flash drive and etc.

HDMI Port

The HDMI port is HDCP compliant and supports Dolby True HD and DTS HD

MasterAudioformats.Italsosupportsupto192KHz/24bit8-channelLPCMaudio output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is 4096x2160@24Hz or 2560x1600@60Hz, but the actual resolutions supported are dependent on the monitor being used.

After installing the HDMI device, make sure to set the default sound playback device to HDMI. (The item name may differ depending on your operating system. The screenshot below is from Windows 8.1)

In Windows 8.1, select Apps>Control Panel>Hardware and Sound>Sound>Playback, set Intel(R) DisplayAudio to the default playback device.

Hardware Installation

- 20 -

Triple Display Configurations for the Onboard Graphics:

Triple-display configurations are supported after you install motherboard drivers in OS. Only dual-display configurations are supported during the BIOS Setup or POST process.

RJ-45 LAN Port (LAN2)

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.

Connection/

Connection/Speed LED:

Activity LED:

Speed LED

Activity LED

State

Description

State

Description

Orange

1 Gbps data rate

Blinking

Data transmission or receiving is occurring

Green

100 Mbps data rate

On

No data transmission or receiving is occurring

Off

10 Mbps data rate

LAN Port

RJ-45 LAN Port (LAN1)

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following describes the states of the LAN port LEDs.

Connection/

Connection/Speed LED:

Activity LED:

Speed LED

Activity LED

State

Description

State

Description

Orange

1 Gbps data rate

Blinking

Data transmission or receiving is occurring

Green

100 Mbps data rate

Off

No data transmission or receiving is occurring

Off

10 Mbps data rate

LAN Port

Line In/Mic In Jack

The line in/Mic in jack. Use this audio jack for line in devices such as optical drive, walkman, microphone, etc.

Line Out

The line out jack. Use this audio jack for a 2-channel speaker. This jack can be used to connect front speakers in a 5.1-channel audio configuration.

Optical S/PDIF Out Connector

This connector provides digital audio out to an external audio system that supports digital optical audio. Before using this feature, ensure that your audio system provides an optical digital audio in connector.

Center/Subwoofer Speaker Out Jack

Use this audio jack to connect center/subwoofer speakers in a 5.1-channel audio configuration.

Rear Speaker Out

Use this audio jack to connect rear speakers in a 5.1-channel audio configuration.

Headphone/Speaker Out Jack

This audio output jack supports audio amplifying function. For better sound quality, it is recommended that you connect your headphone/speaker to this jack(actual effects may vary by the device being used).

Refertotheinstructionsonsettingupa2/5.1-channelaudioconfiguration inChapter6,"Configuring

2/5.1-Channel Audio."

•• When removing the cable connected to a back panel connector, first remove the cable from your device and then remove it from the motherboard.

•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to prevent an electrical short inside the cable connector.

- 21 -

Hardware Installation

1-8 Onboard Buttons, Switches, and LEDs

BIOS Switches and BIOS LED Indicators

The BIOS switch (BIOS_SW) allows users to easily select a different BIOS for boot up or overclocking, helping to reduce BIOS failure during overclocking. The SB switch allows enabling or disabling of the Dual

BIOS function. The LED indicator (MBIOS_LED/BBIOS_LED) shows which BIOS is active.

BIOS_SW

2

1

2

1

SB

2

1

2

MBIOS_LED BBIOS_LED SB		BIOS_SW
			1

1:Main BIOS (Boot from the main BIOS)

2:Backup BIOS (Boot from the backup BIOS)

1:Dual BIOS

2:Single BIOS

BIOS LED Indicators:

MBIOS_LED (The main BIOS is active)

BBIOS_LED (The backup BIOS is active)

Quick Buttons

This motherboard has 3 quick buttons: power button, reset button, and clear CMOS button. The power button and reset button allow users to quickly turn on/off or reset the computer in an open-case environment when they want to change hardware components or conduct hardware testing. Use this button to clear the BIOS configuration and reset the CMOS values to factory defaults when needed.

PW_SW RST_SW

CMOS_SW

PW_SW: Power button RST_SW: Reset button CMOS_SW: Clear CMOS Button

••		Always turn off your computer and unplug the power cord from the power outlet before clearing
		the CMOS values.
••		NOTE: Do not use the clear CMOS button when the system is on, or the system may shutdown
		and data loss or damage may occur.
•• Aftersystemrestart,gotoBIOSSetuptoloadfactorydefaults(selectLoadOptimizedDefaults)or
		manuallyconfiguretheBIOSsettings(refertoChapter2,"BIOSSetup,"forBIOSconfigurations).
Hardware Installation											- 22 -

Audio Gain Control Switches

The two switches allow for audio gain control for the headphone/speaker out jack on the back panel. Please make sure the two dips are set in the same position and are set according to your headphone specification (actual effects may vary by the device being used).

	CAP_SW2 (Left Channel)					CAP_SW1 (Right Channel)
2					1	2				1

CAP_SW2	1: 2.5x (Default)
CAP_SW1

2: 6x

Voltage Measurement Points

Users can use a multimeter to measure component voltages, including VRIN, VIOD, VSA, VAXG, VIOA, VRING, VDIMM, and VCORE. You can employ following way to measure component voltages.

						Pin 1		VRIN
						Pin 1		VIOD	Pin No.	Definition
						Pin 1		VSA	1	Power
						Pin 1		VAXG	2	GND
						Pin 1		VIOA
						Pin 1		VRING
						Pin 1		VDIMM
						Pin 1		VCORE

Steps:

Connecttheredleadofthemultimetertothepin1(Power)ofavoltage measurement point and the black lead to the pin 2 (ground).

- 23 -

Hardware Installation

1-9 Changing the Operational Amplifier

Step 1:

Use an IC extractor to carefully grip the IC's sides and extract it from the socket.

Step 2:

Align the notch on your OP chip with the notch on the socket and gently press the chip into the socket until seated.

For purchasing the IC extractor and OP Chip, please contact the local dealer.

Hardware Installation

- 24 -

1-10 Internal Connectors

1	4	6

		2
	5	3
		12

						9
						8
15						7
						8
						14
11	5	5	13	5	5	10

1)	ATX_12V_2X4	9)	GSATA3 6/7/8/9
2)	ATX	10)	F_PANEL
3)	ATX4P	11)	F_AUDIO
4)	CPU_FAN	12)	F_USB30
5)	SYS_FAN1/2/3/4/5	13)	F_USB1/F_USB2/F_USB3
6)	CPU OPT	14)	CLR_CMOS
7)	SATA_EXPRESS	15)	BAT
8)	SATA3 0/1/2/3/4/5

Read the following guidelines before connecting external devices:

•• First make sure your devices are compliant with the connectors you wish to connect.

•• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power cord from the power outlet to prevent damage to the devices.

•• After installing the device and before turning on the computer, make sure the device cable has been securely attached to the connector on the motherboard.

- 25 -

Hardware Installation

1/2) ATX_12V_2X4/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)

With the use of the power connector, the power supply can supply enough stable power to all the components on the motherboard. Before connecting the power connector, first make sure the power supply is turned off and all devices are properly installed. The power connector possesses a foolproof design. Connect the power supply cable to the power connector in the correct orientation.

The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected, the computer will not start.

To meet expansion requirements, it is recommended that a power supply that can withstand high power consumption be used (500W or greater). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

12 24

1

13

ATX

			ATX_12V_2X4:
			Pin No.	Definition
	5	8	1	GND (Only for 2x4-pin 12V)
	1	4	2	GND (Only for 2x4-pin 12V)
	ATX_12V_2X4		3	GND
			4	GND
			5	+12V (Only for 2x4-pin 12V)
			6	+12V (Only for 2x4-pin 12V)
			7	+12V
			8	+12V
	ATX:
	Pin No.	Definition	Pin No.	Definition
	1	3.3V	13	3.3V
	2	3.3V	14	-12V
	3	GND	15	GND
	4	+5V	16	PS_ON (soft On/Off)
	5	GND	17	GND
	6	+5V	18	GND
	7	GND	19	GND
	8	Power Good	20	-5V
	9	5VSB (stand by +5V)	21	+5V
	10	+12V	22	+5V
	11	+12V (Only for 2x12-pin	23	+5V (Only for 2x12-pin ATX)
		ATX)
	12	3.3V (Only for 2x12-pin	24	GND (Only for 2x12-pin
		ATX)		ATX)

Hardware Installation

- 26 -

3)ATX4P (PCIe Power Connector)

The power connector provides auxiliary power to the onboard PCI Express x16 slots. When two or more graphics cards are installed, we recommend that you connect the SATA power cable(s) from the power supply to the ATX4P connector to ensure system stability.

		Pin No.	Definition
		1	NC
		2	NC
	1	3	NC
		4	GND
		5	GND
		6	GND
	15	7	VCC
		8	VCC
		9	VCC
		10	GND
		11	GND
		12	GND
		13	+12V
		14	+12V
		15	+12V

4/5) CPU_FAN/SYS_FAN1/2/3/4/5 (Fan Headers)

All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.

When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be installed inside the chassis.

CPU_FAN:

Pin No.

Definition

1

1

GND

2

+12V

CPU_FAN

3

Sense

4

Speed Control

SYS_FAN1/2/3/4/5:

Pin No.

Definition

1

1

1

GND

2

Speed Control

SYS_FAN1

SYS_FAN2/3/4/5

3

Sense

4

VCC

•• Be sure to connect fan cables to the fan headers to prevent your CPU and system from overheating. Overheating may result in damage to the CPU or the system may hang.

•• Thesefanheadersarenotconfigurationjumperblocks.Donotplaceajumpercapontheheaders.

- 27 -

Hardware Installation

6)CPU_OPT (Water Cooling CPU Fan Header)

The fan header is 4-pin and possesses a foolproof insertion design. When connecting a fan cable, be sure to connect it in the correct orientation (the black connector wire is the ground wire). The speed control function requires the use of a fan with fan speed control design.

							Pin No.	Definition
							1	GND
	1						2	Speed Control
							3	Sense
							4	VCC

7)SATA_EXPRESS (SATA Express Connector)

The SATA Express connector supports a single SATA Express device.

SATA Express and SATA3 4/5 connectors can only be used one at a time.

Hardware Installation

- 28 -

8) SATA3 0/1/2/3/4/5 (SATA 6Gb/s Connectors, Controlled by Intel® Z97 Chipset)

The SATAconnectors conform to SATA6Gb/s standard and are compatible with SATA3Gb/s and SATA1.5Gb/s standard. Each SATA connector supports a single SATA device. The Intel® Chipset supports RAID 0, RAID 1,

RAID 5, and RAID 10. Refer to Chapter 3, "Configuring SATA Hard Drive(s)," for instructions on configuring

a RAID array.				Pin No.	Definition
	SATA3			1	GND
				2	TXP
7			1	3	TXN
				4	GND
7			1
				5	RXN
1	3	2		6	RXP
				7	GND
0	5	4

9)GSATA3 6/7/8/9 (SATA 6Gb/s Connectors, Controlled by Marvell® 88SE9172 Chips)

The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA 1.5Gb/s standard. Each SATA connector supports a single SATA device. The Marvell® chip supports RAID

0 and RAID 1. Refer to Chapter 3, "Configuring SATAHard Drive(s)," for instructions on configuring a RAID array.

							Pin No.	Definition
		GSATA3					1	GND
	7		1				2	TXP
							3	TXN
				7	9
			1
		7		6	8
							4	GND
							5	RXN
							6	RXP
							7	GND

•• ARAID 0 or RAID 1 configuration requires at least two hard drives. If more than two hard drives are to be used, the total number of hard drives must be an even number.

•• ARAID 5 configuration requires at least three hard drives. (The total number of hard drives does not have to be an even number.)

•• A RAID 10 configuration requires four hard drives.

•• To enable hot-plugging for the SATA ports, refer to Chapter 2, "BIOS Setup," "Peripherals\SATA

Configuration," for more information.

- 29 -

Hardware Installation

10)F_PANEL (Front Panel Header)

Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator on the chassis to this header according to the pin assignments below. Note the positive and negative pins before connecting the cables.

Power LED Power Switch Speaker

PLED+ PLED

-PW

SPEAK+

-SPEAK

PW+

-

2

20

1

19

HD-

CI+

-

-

LED+ LED LED-

RES+

_ _

HD+ RES-

CI

PWR PWR PWR_

Hard Drive

Reset

Power LED

Activity LED

Switch

Chassis Intrusion

Header

•• PLED/PWR_LED (Power LED, Yellow/Purple):

System Status	LED
S0	On
S3/S4/S5	Off

Connects to the power status indicator on the chassis front panel. The LED is on when the system is operating. The LED is off when the system is in S3/

S4 sleep state or powered off (S5).

•• PW (Power Switch, Red):

Connects to the power switch on the chassis front panel. You may configure the way to turn off your system using the power switch (refer to Chapter 2, "BIOS Setup," "Power Management," for more information).

•• SPEAK (Speaker, Orange):

Connects to the speaker on the chassis front panel. The system reports system startup status by issuing a beep code. One single short beep will be heard if no problem is detected at system startup.

•• HD (Hard Drive Activity LED, Blue):

Connects to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data.

•• RES (Reset Switch, Green):

Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart.

•• CI (Chassis Intrusion Header, Gray):

Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has been removed. This function requires a chassis with a chassis intrusion switch/sensor.

The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assignments are matched correctly.

Hardware Installation

- 30 -