Geovision GV-EBD4700, GV-EBD4711, GV-EBD8711, GV-TBL4710, GV-TBL8710 Quick Start Guide
...
Quick Start Guide
GV-IP Camera
GV-EBD Series
GV-ABL / TBL Series
GV-ADR / TDR Series
GV-AVD / TVD Series
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
UBN-QG-L
© 2019 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Ta
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
November 2019
iwan
Contents
Note for Connecting to GV-VMS / DVR / NVR ........................................................ ii
Note for Installing C
Note for Powering the Camera ............................................................................... ii
Note for Face Detection ......................................................................................... iii
Note for People C
1. GV-EBD Series .................................................................................................. 1
1.1 Packing List................................................................................................... 2
1.2 Overview ....................................................................................................... 3
1.2.1 GV-EBD2702 / 4700 / 8700 ............................................................................................3
1.2.2 GV-EBD4711 / 8711......................................................................................................... 4
1.3 Installation ..................................................................................................... 5
1.3.1 GV-EBD2702 / 4700 / 8700 Installation ........................................................................5
1.3.2 GV-EBD4711 / 8711 Installation ..................................................................................... 8
2. GV-ABL / TBL Series........................................................................................11
2.1 Packing List................................................................................................. 12
2.2 Overview ..................................................................................................... 13
2.2.1 GV-ABL2701 / 2703 / 4701 / 4703 & TBL2703 / 4703.............................................. 13
2.2.2 GV-ABL2702 / 4712 / 8712 & TBL4710 / 8710 ..........................................................14
amera Outdoor....................................................................... ii
ounting ...................................................................................... iv
2.3 Installation ................................................................................................... 15
3. GV-ADR / TDR Series...................................................................................... 18
3.1 Packing List................................................................................................. 19
3.2 Overview ..................................................................................................... 20
3.3 Installation ................................................................................................... 21
4. GV-AVD / TVD Series ...................................................................................... 24
4.1 Packing List................................................................................................. 25
4.2 Overview ..................................................................................................... 26
4.3 Installation ................................................................................................... 27
5. Waterproofing the Cable ................................................................................ 29
6. Accessing the C
6.1 System Requirements ................................................................................. 31
6.2 Looking Up the Dynamic IP Address ........................................................... 32
6.3 Configuring the IP Address.......................................................................... 34
7. The Web Interface........................................................................................... 35
8. Upgrading System Firmware ......................................................................... 37
9. Restoring to Factory Default.......................................................................... 38
amera ................................................................................... 31
i
Note for Connecting to GV-VMS / DVR / NVR
The GV-IPCAM is designed to work with and record on GV-VMS / DVR / NVR, a video
management system.
Once the camera is connected to the GV-VMS / DVR / NVR, the resolution set on
the GV-VMS / DVR / NVR will override the resolution set on the camera’s Web
interface. You can only change the resolution settings through the Web interface
when the connection to the GV-VMS / DVR / NVR is interrupted.
The login password of the camera cannot contain the character “&” or any
whitespace when connecting to GV-VMS.
The Video Analytic features under Intelligent (See 3.5 Intelligent in the User’s
Manual) cannot be integrated with GV-VMS / DVR / NVR
Note for Installing Camera Outdoor
When installing the camera outdoor, be sure that:
1. The camera is set up above the junction box to prevent water from entering the
camera along the cables.
2. Any PoE, power, audio and I/O cables are waterproofed using waterproof silicon
rubber or the like.
3. The screws are tightened and the cover is in place after opening the camera
cover.
Note for Powering the Camera
The Camera is powered by PoE. If you want to power the camera using the power
connector, an optional power adapter is required.
ii
Note for Face Detection
To use the camera’s built-in face detection feature (see 3.5.1.7 Face Detection in the
User’s Manual), not supported by GV-ABL2701 / 2703 / 4701 / 4703, GV-ADR2701 /
2702 / 4701 / 4702, GV-TBL series, GV-TDR2702 / 4702 and GV-TVD series, it is
recommended to install the camera according to the criteria listed below:
Surveillance Condition
The camera shall be installed at a site with uniform, sufficient lighting, where the
face(s) to be detected are fully illuminated.
Example of Recommended Scene Example of Non-recommended Scene
Camera Position
The camera shall be mounted at a recommended height of 2.5 ~ 3 m.
The camera shall be mounted with a recommended depression angle of around
10°.
The camera shall be positioned so that the face(s) to be detected are directly
aligned with the lens of the camera, with a horizontal deviation of no greater than
30°, a vertical deviation of no greater than 15° and a face size of at least 120
pixels.
iii
Note for People Counting
To use the camera’s built-in people counting feature (see 3.5.1.8 People Counting in
the User’s Manual), not supported by GV-ABL2701 / 2703 / 4701 / 4703,
GV-ADR2701 / 2702 / 4701 / 4702, GV-TBL series, GV-TDR2702 / 4702 and GV-TVD
series, it is recommended to install the camera according to the criteria listed below:
Surveillance Condition
The camera shall be installed at a site with uniform, sufficient lighting, where the
person(s) to be counted are fully illuminated.
The camera shall be installed at an entrance or exit with an ideal width of 1 ~ 4 m,
where the persons(s) to be counted move toward the lens of the camera in single
file.
Example of Recommended Scene Example of Non-recommended Scene
Camera Position
The camera shall be mounted at a recommended height of 3 ~ 5 m.
The camera shall be mounted with a recommended depression angle of 70 ~ 80°.
The camera shall be positioned so that the person(s) to be counted face toward
the lens of the camera and are displayed on the image with a shoulder size of
between 120 ~ 160 pixels.
iv
1. GV-EBD Series
Camera Type Model No.
GV-EBD2702 (IP67)
GV-EBD4700 (IP67)
Eyeball IP Dome
GV-EBD4711 (IP67)
GV-EBD8700 (IP67)
GV-EBD8711 (IP67)
1
1.1 Packing List
H.265 Target Eyeball Dome
Screw Kit
Waterproof Rubber Set
Drill Template Paster
Download Guide
Warranty Card
2
1.2 Overview
1.2.1 GV-EBD2702 / 4700 / 8700
GV-EBD Series
1
No. Description
1 Bottom ring
2 Housing
3 Lens
4 Infrared indicator
5 Power connector (DC 12 V)
6 Ethernet connector / PoE
3
1.2.2 GV-EBD4711 / 8711
No. Description
1 Bottom ring
2 Housing
3 Microphone
4 Lens
5 Power connector (DC 12 V)
6 Ethernet connector / PoE
7 Micro SD card slot and default button compartment
8 Default button
9 Micro SD card slot
Note: If the default button doesn’t respond after pressing for 15 seconds, reboot the
camera and try again within 10 minutes of rebooting.
4
GV-EBD Series
1
1.3 Installation
The Target Eyeball Dome is designed for outdoors. With the standard package, you
can install the camera on the ceiling. Or you can purchase optional mounting
accessories to mount the dome on a wall.
Below are the instructions for Ceiling Mount. There are two kinds of Ceiling Mount:
Concealed Installation and Open Installation. In Concealed Installation, the cables
are hidden in the ceiling. In Open Installation, the cables are led out from the open slot
on t he bottom ring.
1.3.1 GV-EBD2702 / 4700 / 8700 Installation
For Concealed Installation
1. Stick the drill template paster to the ceiling and drill three holes according to the
drill template.
8
2. Insert the screw anchors.
5
3. Remove the bottom ring by turning it anticlockwise.
Bottom Ring
4. Connect the cables and secure the camera.
5. Adjust the monitoring direction.
6
Loading...