GBC H210, H310 User Manual
HeatSeal™H210/ H310
ABC Office
800.658.8788
www.abcoffice.com
2
31
HeatSeal™H210/ H310 HeatSeal™H210/ H310
4 5
Electrical safeguards
• The unit must be connected to a supply voltage corresponding to the
electrical rating shown on the unit.
• Unplug the unit before moving it, or when it is not in use for an extended
period of time.
• Do not operate with a damaged supply cord or plug. Do not alter the
attachment plug. The plug is configured for the appropriate electrical
supply.
• Do not overload electrical outlets beyond their capacity; fire or electrical
shock could result.
• The unit is intended for indoor use only.
• Never push objects through the cabinet slots. Do not spill liquid of any
kind on this product.
• Close supervision is required when this product is used near children.
Service
• Do not attempt to service or repair the pouch laminator yourself. Unplug
the unit and contact an authorized GBC service representative for any
required repairs.
Cleaning
General safeguards
• Use the unit only for its intended purposes of laminating documents.
• Do not place anything in the throat opening of the laminator other than
pouches/documents/carriers.
• Place unit on a secure, stable work area to prevent the unit from falling
and possibly causing personal injury and damage to the unit.
• Follow all warnings and instructions marked on the unit.
• The socket outlet shall be installed near the equipment and shall be
easily accessible.
• Do not block the vent slots, this will cause the laminator to overheat.
Safety instructions
YOUR SAFETY AS WELL AS THE SAFETY OF OTHERS IS
IMPORTANT TO GBC. IN THIS INSTRUCTION MANUAL AND ON THE
PRODUCT ARE IMPORTANT SAFETY MESSAGES. READ THESE
MESSAGES CAREFULLY.
THE FOLLOWING WARNING IS FOUND ON THE PRODUCT IN SEVERAL
LANGUAGES.
This safety message means that you could be seriously hurt or killed if you
open the product and expose yourself to hazardous voltage.
The following ISO and IEC symbols appear on this product, and their
meaning is as follows:
Electrical shock hazard.
Do not open. No user
servicable parts inside.
Refer servicing to qualified
service personnel.
WARNING
Caution: Unplug this product before cleaning.
THE SAFETY ALERT SYMBOL PRECEDES EACH
SAFETY MESSAGE IN THIS INSTRUCTION MANUAL.
THIS SYMBOL INDICATES A POTENTIAL PERSONAL
SAFETY HAZARD THAT COULD HURT YOU OR
OTHERS, AS WELL AS CAUSE PRODUCT DAMAGE
OR PROPERTY DAMAGE.
WARNING: FOR YOUR PROTECTION DO NOT CONNECT
THE POUCH LAMINATOR TO ELECTRICAL POWER
UNTIL YOU READ THESE INSTRUCTIONS COMPLETELY.
KEEP THESE INSTRUCTIONS IN A CONVENIENT
LOCATION FOR FUTURE REFERENCE. TO GUARD
AGAINST INJURY, THE FOLLOWING BASIC SAFETY
PRECAUTIONS MUST BE OBSERVED IN THE SET-UP
AND USE OF THIS PRODUCT.
Important safeguards
• Wipe exterior only with a damp cloth. Do not use detergents
or solvents.
Important: Before operating your new laminator, lift up the exit tray located at the rear of the machine and lock it in place (fig. 1).
Special notice
Thank you, for your recent purchase of a GBC Pouch Laminator. Your new
laminator may emit a slight odour during the initial stage of operation. It is
normal and will diminish after several hours of operation.
Do not attempt to do single sided lamination. This will destroy the carrier.
Release
On/Off
Heat
Cold
Warranties
Operation of this machine is guaranteed for two years from date of
purchase, subject to normal use. Within the guarantee period, GBC will
at its own discretion either repair or replace the defective machine free
of charge. Defects due to misuse or use for inappropriate purposes are
not covered under the guarantee. Proof of date of purchase will be
required. Repairs or alterations made by persons not authorised by GBC
will invalidate the guarantee. It is our aim to ensure that our products
perform to the specifications stated. This guarantee does not affect the
legal rights which consumers have under applicable national legislation
governing the sale of goods.
5
6
7
4
Operation, hot lamination
Specifications
Electrical
Machine Dimensions
Machine Weight
Maximum Pouch Width
Maximum Pouch Thickness
Maximum Thru-put Thickness
Warm-Up Time
(2 x 75 mic)
GBC HeatSeal H210
120V / 60Hz / Amps / W
400 x 173 x 117.5mm (15.75” x 6.75” x 4.62”)
2.7 kg (6 lbs.)
241mm (9.5”)
5mil.
1.0 mm (.040”)
5 minutes
Connect power cord to appropriate power source.
Push the power button to turn the power "ON" (fig. 2). The inside of
the laminator will glow red.
Using the lamination guideline table here below, select the appropriate
temperature setting for the pouch gauge thickness and material you
are laminating.
• If the laminated item appears to be cloudy, it means that the
laminator temperature is not hot enough. Allow the laminator to heat
for a few more minutes then run the pouch through again.
• If the laminated item is wavy, the TEMPERATURE is too hot.Verify
temperature selector is set at the appropriate temperature.
• Always allow sufficient time for the laminator to adjust to changes in
temperature setting.
The inside of the laminator will glow green when the laminator has
reached operating temperature.
Position the document to be laminated into a GBC laminating pouch,
so that the document is aligned to the folded sealed edge and the right
and left borders are equal and insert the pouch into the
carrier (fig. 3).
Insert the carrier straight into the machine,
leading with the folded
edge
(fig. 4).
The carrier will automatically exit the rear of the machine. After the
carrier has stopped moving, immediately place it on a flat surface to
cool for one minute before handling (fig. 5).
If you have finished laminating, push the switch to turn "OFF" the
machine.
Register this product online at www.gbc.com
1
2
3
4
5
6
7
8
Helpful lamination hints
Temperature setting Guidelines:
When laminating thin paper with light ink coverage, set the
temperature dial at the low end of the range. Thick paper and heavy
ink coverage require higher settings. Temperature settings will vary due
to the finish, chemistry and heat absorption properties of the material
being laminated.
Before laminating important or unique documents always run a test
pouch through the laminator using a similar type document.
As soon as the lamination is completed, remove from the rear of the
machine and place on a cool flat surface for cooling to prevent the
pouch from curling.
Your Laminator is equipped with an
automatic shut-off function.
If the machine remains idle for one hour, the heater function will
automatically shut down. To reset the machine for operation, push
the power button off first and back on again.
1
2
3
4
GBC HeatSeal H310
120V / 60Hz / Amps / W
476 x 173 x 117.5mm (18.75” x 6.75” x 4.62”)
3.75 kg (8.25 lbs.)
318mm (12.5”)
5mil.
1.0 mm (.040”)
6 minutes
Copy Paper Setting
Glossy Paper Setting
Photo Paper Setting
2 - 4
4 - 6
7 - 8
4 - 6
6 - 8
9 - 10
3 mil. 5 mil.
Operation, cold lamination
Connect power cord to appropriate power source.
Rotate the temperature dial to the "cold" position (fig. 2).
Push the power button to turn the power "ON" (fig. 2).
The inside of the laminator will glow green.
Use and laminate your GBC cold pouch.
(Pressure sensitive—non-thermal laminating pouch)
1
2
3
4
5
Anti-jam feature: Important Information
How to use the release lever.
If carrier jams or is fed improperly, turn off the laminator immediately.
Press the release lever down to release the motor from the rollers (fig. 6).
Pull your carrier out of the laminator while pressing the release lever
down (fig. 7).
Continue laminating.
1
2
3
4
CARRIER
CARRIER
ABC Office
800.658.8788
www.abcoffice.com
Loading...