Gaylord PG-BDL-BB User Manual

MODEL “PG-BDL-BB”

SERIES FILTER HOOD

GENERAL SPECIFICATIONS

Furnish Gaylord Exhaust Hood Model “PG-_____-BDL-BB-_______”
as shown on plans and in accordance with the following specifications:

GENERAL: Each exhaust hood shall be designed specifically for the
cooking equipment being covered.

The exhaust hood shall be configured with two separate exhaust
plenums and two exhaust duct collars. Each plenum shall include a
stationary grease collecting gutter at the bottom of the grease extraction
device, sloped to a drain at one end to a removable stainless steel
grease cup. The sloped gutter shall be concealed by an apron which
extends the full length of the hood. Continuous front and rear brackets
shall be provided to facilitate hanging from the overhead building
structure. Each exhaust hood shall contain one or more stainless steel
baffle filters. Filters shall be self draining, UL classified and mounted no
less than a 45° angle from horizontal.

o Fuse Link Activated Fire Damper (Series Prefix PG) The exhaust
hood shall include a fire damper located in each exhaust duct collar. The
damper shall be activated by fuse link(s), and upon activation, the
damper shall close, and act as a fire barrier to prevent flame from
entering the duct system. The damper shall be manually reset without
the use of tools and without opening or removing access panels. The
exhaust hood shall be UL listed under the category “Exhaust Hood with
Exhaust Damper.”

o Exhaust Hood without Fire Damper (Optional - Series Prefix
PG-ND) The exhaust hood shall be UL listed under the category

“Exhaust Hood without Exhaust Damper.”

CONSTRUCTION: The ventilator shall be of all stainless steel con­struction, not less than 18 gauge, type 300 series. All exposed surfaces
shall be a number 4 finish. The use of aluminized steel, galvanized steel,
or 430 stainless steel is not acceptable.

LIGHT FIXTURES: The exhaust hood shall be equipped with o 100
watt surface mounted incandescent, o 150 watt recessed incandes­cent, o recessed fluorescent, light fixtures. Light fixtures shall be
factory pre-wired to a single connection point. Exhaust hoods built in
multiple sections shall be furnished with coiled flex conduit for intercon­necting sections, in the field by others.

ACCEPTANCE & APPROVALS: The exhaust hood shall be UL, CUL
and NSF listed. The exhaust hood shall comply with all requirements of
NFPA-96, IMC, UMC, BOCA, and SBCCI model codes.

ITEM NO. _______________

APPLICATION

Island style for all double island arrangements.

FEATURES

• UL, CUL and NSF Listed

• “Super Capture”TM Lip - Enhances Capture
and Reduces Exhaust Volume

• Complies With The IMC, UMC, BOCA and
SBCCI Mechanical Codes

• Complies With All Requirements of NFPA-96

OPTIONAL ACCESSORIES

• Decorative Facings and Trim

• Built-in Light & Fan Switch

• Built-in Fire Extinguishing Systems

DESCRIPTION

The Gaylord “PG” series exhaust hood is an economy hood that
maintains the “standards” in materials, construction and quality found
in all Gaylord Water-Wash and Non Water-Wash high efficiency
extractor ventilators. The “PG” series hood uses stainless steel baffle
filters as a standard. A fuse link activated fire damper is standard, or
the hood may be provided without a fire damper.

The “PG” series has been tested to UL standard 710 and is listed either
under the category “Exhaust Hood with Exhaust Damper” or “Exhaust
Hood without Exhaust Damper.”

OPTIONAL EQUIPMENT

1. Exhaust Fans, Supply Fans, & Roof Top Units

2. Fire Extinguishing Systems

3. Utility Distribution Systems

4. Pollution Control Systems

GAYLORD INDUSTRIES

10900 S.W. AVERY STREET • TUALATIN, OREGON 97062 U.S.A.

PHONE: [phone] • FAX: [phone] • email: [e-mail]

www.gaylordusa.com

MODEL “PG - ____ -BDL-BB- ____”

ND

For exact model designation add appropriate
suffixes.
Example: “PG-BDL-BB-108”

DEPTH

OF

VENTILATOR

ITEM NO. ______________________ EST. WT. _________________________

LENGTH _____________ WIDTH ______________ HEIGHT ______________

EXHAUST - CFM ________________ DUCT SIZE ____________ S.P. ______

(SIDE A)

EXHAUST - CFM ________________ DUCT SIZE ____________ S.P. ______

(SIDE B)

LIGHTS VOLTAGE

qq

100W SURFACE INCANDESCENT

q

qq
qq

150W RECESSED INCANDESCENT

q

qq
q q

RECESSED FLUORESCENT

q

q q

q q

120 VOLTS

q

q q
q q

220/240 VOLTS

q

q q

The manufacturer reserves the right to
modify the materials and specifica­tions resulting from a continuing pro­gram of product improvement or the
availability of new materials

TYPICAL SECTION VIEW

ENGINEERING DATA

Mechanical Requirements

The amount of exhaust volume required is dependent upon the type and
volume of cooking. The model “PG-BDL-BB” may be designed with different
air volumes from one side to the other as determined by the cooking
equipment. Refer to the Master Engineering Data Sheet in the Engineering
Data section of the Gaylord catalog for the charts on determining exhaust
volume, duct sizes, and static pressure.

Electrical

A Gaylord stop/start switch, Model C-150, may be provided as an option for
each exhaust fan. Lights to be on separate circuit, 120 volt standard, 220/
240 volt optional.

Form No. PG-BDL-BB 0307 / 30719 © Copyright 2007, Gaylord Industries Litho USA

Ventilator Lengths

Maximum unit length 16'-0". For greater lengths, join two or more sections
together. Check to ensure that there is adequate access into building and
kitchen area.

Note: Ventilators manufactured outside North America; maximum unit length

*

10'-0".

Hanging Weight

Ventilator Width 8'-0" 9'-0" 10'-0" 11'-0"
Wt. / Lineal ft. Lbs. 130 140 150 160