Futaba ATTACK BFR, ATTACK, ATTACK R User Manual
Futaba
DIGITAL PROPORTIONAL
RADIO CONTROL
New ATTACK
New ATTACK-R
New ATTACK-BFR
•The NEW ATTACK, NEW ATTACK-R is a high performance 2 channel digital proportional
R/C set based on the acclaimed ATTACK and has a built-in BEC (Battery Eliminator
Circuitry) system.
•The NEW ATTACK-BFR is the newest 2 channel digital proportional R/C set with a builtin ASP (Adjustable Safety Position) system, plus the functions of the NEW ATTACK.
Thank you for purchasing a Futaba digital proportional radio control set.
Please read this manual carefully before using your set.
CONTENTS AND RATINGS ............ 2
TRANSMITTER FP-T2NBL, FP-T2NBR AND
FP-T2NBFR ...................... 2
LOADING THE PENLIGHT BATTERIES . .3
STEERING TRIM LEVER ADJUSTMENT. .3
THROTTLE STICK NEUTRAL LEVER
OPERATION
CRYSTAL
REPLACEMENT
Since the power receiver and servo power is supplied from the running
Nicd battery, there is no troublesome wiring and the vehicle can be made
lighter.
It is a safety system which protects the vehicle against loss of control due
to a discharged Nicd by detecting a drop in the voltage of the running
Nicd battery which is a shared power supply and stops the vehicle.
....................
...........
SYSTEM
SYSTEM
CONTENTS
RECEIVER AND SERVOS ............. 5
4
4
& ASP SYSTEM
SWIVEL
USING
ASP
ASP
IF ASP OPERATES ..............
WHEN VEHICLE DOES NOT RUN ....
STICK
SETTING
THE
FREQUENCY
SETTING
OPERATION
...................
...........
FLAG
.................
......
4
7
8
9
10
10
FEATURES OF NEW ATTACK NEW ATTACK-R AND NEW ATTACK-BFR
The NEW ATTACK, NEW ATTACK-R has a BEC function.
The NEW ATTACK-BFR has BEC & ASP functions.
•The
BEC (Battery Eliminator Circuitry)
circuit (regulator). Since the running Nicd battery can also be used as the receiver servo
power supply, there is no troublesome wiring and the vehicle can be made lighter.
(Installed in NEW ATTACK, NEW ATTACK-R and NEW ATTACK-BFR.)
•The
ASP (Adjustable
safety
system
which protects the
Safety
Position)
by detecting a drop in the voltage of the shared power supply Nicd battery and automatically
sets
the
throttle
servo
to the
then allows steering with the remaining power before steering control is lost. When the
voltage of the running Nicd battery recovers, ASP is automatically reset and the normal
running functions are recovered by turning on the transmitter power switch. (Installed
in NEW ATTACK-BPR)
World's first safety system that allows running of the vehicle up to the finish
line while using the capacity of the power supply to the fullest without a loss of
steering control even when the voltage of the running Nicd battery drops.
•Transmitter is Built-in servo reverse switches. (New ATTACK-R, NEW ATTACK-BFR)
system
vehicle
drive
system
is a high performance constant voltage
prevents
against
motor off position
loss
loss
of control due
of
steering
preset
to a discharged
control.
It
is
a
Nicd
at the transmitter
TRANSMITTER FP-T2NBL/T2NBR/T2NBFR
•ASP (Adjustable Safety Position) system allows safe
recovery without a loss of steering control. (T2NBFR
only)
•New swivel stick system that allows selection
stick lever operating direction over a range of 10°.
•Racing specification short
operation extremely easy.
•New
neutral
lever
of the throttle stick in two stages. Perfectly matched to
the throttle position of motor and engine cars. The stick
can be changed to a ratchet system by installing an
optional slider.
•
Servo
reverse
Since each servo can be switched between forward and
reverse from the outside of the transmitter, linkage
hookup is extremely easy. (T2NBR, T2NBFR)
• Level meter shows the state of the battery at a
•Crystal
• Hook. Optional neck strap can be used.
can be changed from the outside. (Except 72.I
75MHz)
allows setting of
switches (steering
aluminum stick lever makes
the
neutral
& throttle).
of the
position
glance.
RECEIVER FP-R102GF
•BEC (Battery Eliminator Circuitry) system allows
sharing of the running Nicd battery and eliminates the
need for a regulator and diode.
•High
performance 2 channel
when used with the proper transmitter.
•Crystal socket uses a new type of highly reliable subminiature pins. Reliability is increased and the crystal
can be changed from the outside.
receiver
with
ASP system
SERVO FP-S128
SMALL, RUGGED, HIGH NEUTRAL SERVO
•Skew type armature motor.
Movement of the trimmer by even one notch is tracked
by a skew type motor which displays a performance
near that of a coreless motor.
• New indirect drive potentiometer improves
and shock resistance and neutral accuracy.
• Futaba low-power custom 1C provides extremely
torque, narrow dead band, and superior tracking.
• Fiberglass reinforced PBT (polybutylene terephthalate)
injection molded servo case is mechanically strong
invulnerable to glow fuel.
•Strong polyacetal resin ultra-precision servo gear fea-
tures smooth operation, positive neutral, and very little
backlash.
• Fiberglass reinforced epoxy resin PC board with thru-
the-hole plating improves servo amp vibration and shock
resistance.
• Three pin connector eliminates faulty contact and im-
proves reliability against vibration and shock. Housing
has a reverse insertion prevention mechanism.
•Special grommet simplifies mounting
has an excellent cushioning effect.
•Six special adjustable splined horns.
•High 48.7oz.jn (3.5kg-cm) maximum output torque
allows use in almost any model.
of the servo and
vibration
high
and
1
CONTENTS AND RATINGS
Transmitter
Receiver
Servo
Battery holder
FP-T2NBL x 1
FP-R102GFx 1
FP-S128x2
R2-BSS-N x 1
Others
Transmitter FP-T2NBL/T2NBR T2NBFR
Operating system
Transmitting
frequency
Modulation
Power requirement
Current drain
2 nick
27MHz, bands 1 to 6 72, 75MHz
AM (Amplitude Modulation)
12.0V, penlight battery x 8
170mA
TRANSMITTER FP-T2NBL/T2NBR/T2NBFR
• Nomenclature
•The
name
of
each
part of
the
shown in the figure. Learn them before operating your set.
When running the vehicle, extend the antenna
fully.
transmitter
Receiving
frequency
Intermediate
frequency
Selectivity
Receiving range
Power supply
Dimensions
Weight
is
FP-T2NBR x 1
FP-R102GF x 1
FP-S128x2
R2-BSS-N x 1
Switch, frequency flag, spare horn
Ratings are subject to change without prior notice.
Receiver FP-R102GF
27MHz band. bands 1 to 6
72. 75MHz
455kHz
3kHz/-3dB
550 yards (500m) on the ground
when used with FP T2NBLIA1 the
best
radio
wave
condition
environment)
4.8V to 8 4V
7.2V/13mA. 4 8V/33mA
1.46 x2.19x0.75 in
(37 x 55.5 x 19mm)
1.34
oz
138g)
BEC & ASP functions
of
Before using the set, check the remaining
battery capacity by checking the level meter.
Good
FP-T2NBFR x 1
FP-R102GF x 1
FP-S128x 2
R2BSS-N x 1
Control system
Operating angle
Power
requirement
Current drain
(IDLE)
Output torque
Operating speed
Dimensions
Weight
SERVO FP-S128
pulse width control
One side 45° or more
4.8V
-6
6.0V. 8mA (at Idle)
48.7 oz.in. 13.5 kg-cm)
0.24 sec/60
16x08x 1.6 in.
(40.5 x 20 x 40.5mm)
1.92oz. 153g)
Caution No good
Change the battery.
Frequency flag
Neutral lever
Throttle trim
Throttle stick
ASP setting
trimmer
ASP setting
switch
(NEW ATTACK-BFR only)
Servo reverse switches
(NEW ATTACK-R, NEW ATTACK-BFR)
Antenna
Level meter
Handle
Hook
Steering stick
Steering trim
Power switch
Transmitter
crystal holder
2
•LOADING THE PENLIGHT BATTERIES
• Remove the battery cover at the rear and insert eight penlight batteries in the correct polarity.
Remove the cover by push-
ing here and sliding down.
• Extend the antenna fully and set the power switch to ON.
The level meter pointer should deflect to the silver zone. If the pointer does not move, or moves very little, check for poor battery contact, incorrect battery polarity, or faulty batteries.
• If the pointer of the level meter deflects to the red zone, the range of
the radio waves will become short. When the pointer drops to the
boundary between the silver and red zones, change the batteries.
•The
trim
levers
are
used
to fine
adjust
the
used to adjust the neutral position and for correcting the running
steering
posture after the mechanism is mounted. After test running, make
corrections with the rod adjuster, etc. and operate the set with the
trim levers in the neutral position as much as possible.
angle.
They
•Servo reverse switches
(NEW ATTACK-R. NEW ATTACK-BFR)
• This switch makes servo rotation to anotherdirection.
• After fixed servos onto your model, and found
that rotation is wrong-way, switch to another
direction.
•Servo reverse switches are located at bottom of
Transmitter case like drawing below:
•Steering trim lever adjustment
When vehicle was run straight.
are
Load the eight pen-light
batteries while paying care-
ful attention to their-polarity.
Steering servo
reverse
switch
Normal Reverse
When vehicle was run straight •
Throttle
servo reverse
switch
Normal Reverse
When vehicle turns
to the right
Move the trim lever slowly
to the left so that the vehicle runs straight.
•Adjust the trim lever so that the vehicle runs straight on a smooth road.
The throttle trim lever is used to fine adjust the speed controller stop position, etc.
Move the trim lever slowly
to the right so that the
vehicle runs straight.
3
When vehicle turns
to the left
Loading...