Funai MJ840G User Manual

Download

PrecautionsSetupVCR FunctionsDVD FunctionsEspañol Information

INSTRUCCIONES EN ESPAÑOL INCLUIDAS.

Supplied Accessories

AC outlets

Plug in

From TV

From DVD/VCR

Please refer to “Connections” on page 6.

Cable TV

signal

ANT-OUT

ANT-IN

RF cable (supplied)

(Back of DVD/VCR)

(Back of TV)

Antenna

Connect

(Back of TV)

Disconnect

Antenna

Cable TV

signal

Basic TV Connection

If you need additional operating assistance

after reading this owner’s manual, please call

TOLL FREE : 1-866-845-9436

Table of Contents

Remote control (NB177UD) with two AA batteries

RF cable (WPZ0901TM002)

Audio/Video cables (WPZ0102TM015 / WPZ0102LTE01)

Owner’s Manual (1VMN22699)

Owner's Manual

DVD/CD Player with Video Cassette Recorder

MJ840G

Owner’s Manual

Please read before using this unit.

Precautions

Laser Safety ................................................................................. 2

■ Important Safeguards ................................................................ 3

Location and Handling ................................................................. 4

Avoid the Hazards of Electrical Shock and Fire .......................... 4

Moisture Condensation Warning .................................................. 4

About Copyright ........................................................................... 4

Symbols Used in This Manual .....................................................4

Maintenance ................................................................................. 4

■ About the Video Cassettes and Discs ...................................... 5

Playable Video Cassettes ............................................................ 5

Playable Discs ............................................................................. 5

Unplayable Discs ......................................................................... 5

Setup

■ Connections ................................................................................ 6

RF Output Channel ...................................................................... 6

Hint for Cable Box or Satellite Box .............................................. 6

Connection to an Audio System .................................................. 6

Connection to a TV ...................................................................... 7

■ Preparation for Use .................................................................... 8

Turn on the Unit for the First Time............................................... 8

To Add or Delete Channels ......................................................... 8

Clock Setup .................................................................................. 8

■ Function Overview ..................................................................... 9

Front Panel Indicator .................................................................... 9

VCR / DVD Switching .................................................................. 9

Front & Rear Terminals................................................................ 9

Remote Control ........................................................................... 10

Installing the Batteries for the Remote Control ........................... 10

VCR Functions

■ Playback ..................................................................................... 11

■ Other Operations ....................................................................... 11

Index Search ............................................................................... 11

Time Search ................................................................................ 11

Auto Repeat ................................................................................ 12

■ Recording ................................................................................... 12

Recording & OTR (One Touch Recording) ................................. 12

Timer Recording ......................................................................... 12

Hints for OTR and Timer Recording ...........................................13

Copying a Video Tape ................................................................ 14

DVD Functions

■ Playback ..................................................................................... 15

■ On-Screen Display ..................................................................... 16

■ Search Functions ...................................................................... 17

Using Track Search .................................................................... 17

Using Title / Chapter Search ....................................................... 17

Using Time Search ..................................................................... 17

Marker Setup .............................................................................. 17

■ Repeat / Random / Programmed Playback ............................. 18

Repeat Playback / Repeat A-B Playback

Random Playback / Programmed Playback ...............................18

■ Special Settings ......................................................................... 19

Subtitle Language / Audio Language / Camera Angle

Black Level Setting / Stereo Sound Mode / Virtual Surround ..... 19

■ DVD Setup .................................................................................. 20

LANGUAGE Setting .................................................................... 20

DISPLAY Setting ......................................................................... 21

AUDIO Setting ............................................................................ 21

PARENTAL Setting ..................................................................... 22

OTHERS Setting ......................................................................... 22

Reset to the Default Setting (Except for PARENTAL Setting) .... 23

Information

■ Troubleshooting Guide ............................................................. 23

■ Specifications ............................................................................ 24

■ Language Code List .................................................................. 24

■ Limited Warranty ....................................................................... 28

■ Español ....................................................................................... 29

■ Quick Use Guide ........................................................................ 31

Precautions

–

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED

HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO

BEAM.

LOCATION: INSIDE, NEAR THE DECK MECHANISM.

WARNING

: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

RADIO-TV INTERFERENCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications

to this equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE

DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

Precautions

Laser Safety

For Customer Use: Read carefully the information located at the back of this unit and enter below the Model No. and the Serial No. Retain this information for future reference.

Model No. ____________________ Serial No. ____________________

Make your contribution to the environment!!!

• Used up batteries do not belong in the dust bin.

• You can dispose of them at a collection point for used up batteries or special wastes. Contact your council for details.

The lightning ﬂ ash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufﬁ cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The caution marking is located on the rear of the cabinet.

Precautions

–

1. Read Instructions - All the safety and operating instructions should be read before the appliance is operated.

2. Retain Instructions- The safety and operating instructions should be retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the operating instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should be followed.

5. Cleaning - Unplug this video product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. EXCEPTION: A product that is meant for uninterrupted service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.

6. Attachments - Do not use attachments not recommended by the video product manufacturer as they may cause hazards.

7. Water and Moisture- Do not use this video product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.

8. Accessories - Do not place this video product on an unstable cart, stand, tripod, bracket, or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the appliance should follow the manufacturer's instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

9. Ventilation - Slots and openings in the cabinet are pro

vided for ventilation and to ensure reliable operation of the video product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the video product on a bed, sofa, rug, or other similar surface. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instructions have been adhered to.

10. Power Sources - This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

11. Grounding or Polarization - This video product is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.

12. Power Cord Protection - Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.

13. Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the video product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/ NFPA No. 70, provides information with regard to proper

grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)

FIGURE A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

ANTENNA LEAD WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

NEC – NATIONAL ELECTRICAL CODE

S2898A

14. Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the video product due to lightning and power-line surges.

15. Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

16. Overloading - Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

17. Object and Liquid Entry - Never push objects of any kind into this video product through any openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the video product.

18. Servicing - Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

19. Damage Requiring Service - Unplug this video product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the

video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by

following the operating instructions. Adjust only those

controls that are covered by the operating instructions

as an improper adjustment of other controls may result

in damage and will often require extensive work by a

qualified technician to restore the video product to its

normal operation. e. If the video product has been dropped or damaged in

any way. f. When the video product exhibits a distinct change in

performance this indicates a need for service.

20. Replacement Parts - When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.

21. Safety Check - Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.

22. Heat - This video product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

IMPORTANT SAFEGUARDS

Precautions

–

Maintenance

SERVICING

• Please refer to relevant topics on the “Troubleshooting Guide” on page 23 before returning the product.

• If this unit becomes inoperative, do not try to correct the problem by yourself. There are no user-serviceable parts inside. Turn off, unplug the power plug, and please call our help line mentioned on the front page to locate an Authorized Service Center.

CLEANING THE CABINET

• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits, ammonia or abrasive.

CLEANING DISCS

• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center to out. Do not wipe in a circular motion.

• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analog records.

CLEANING THE DISC LENS

• If this unit still does not perform properly although you refer to the relevant sections and to “Troubleshooting Guide” in this Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

DISC HANDLING

• When you handle a disc, hold it by its edge and try not to touch the surface of the disc.

• Always store the disc in its protective case when it is not used.

AUTO HEAD CLEANING

• Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.

• Playback picture may become blurred or interrupted while the TV program reception is clear. Dirt accumulated on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in your unit may need to be cleaned.

1. Please visit your local Audio/Video store and purchase a

good quality VHS Video Head Cleaner.

2. If a Video Head Cleaner does not solve the problem,

please call our help line mentioned on the front page to locate an Authorized Service Center.

Location and Handling

•

Do not stand this unit up vertically. Install this unit in a horizontal and stable position. Do not place anything directly on top of this unit. Do not place this unit directly on top of the TV.

• Depending on the TV, noise or disturbance of the picture and/or sound may be generated if this unit is placed too close to your TV. In this case, please ensure enough space between your TV and this unit.

• Do not cover or place this unit in enclosed spaces to prevent excessive temperature build up.

•

Do not place this unit in direct sunlight, or near heat sources.

• Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.

• Keep this unit away from strong magnetic objects.

• Do not place any object containing water or other liquids on this unit. In the event that liquid should enter the cabinet, unplug this unit immediately and contact the retailer or an Authorized Service Center immediately.

• Do not remove this unit cabinet. Touching parts inside the cabinet could result in electric shock and/or damage to this unit. For service and adjustment inside the cabinet, call a qualified dealer or an Authorized Service Center.

• Be sure to remove disc and video tape and unplug the AC power cord from the output before carrying this unit.

Avoid the Hazards of Electrical Shock and Fire

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from AC wall outlet. Grasp it by the plug.

• If, by accident, water is spilled on this unit, unplug the power cord immediately and take the unit to our Authorized Service Center for servicing.

•

Do not put your fingers or objects into the unit cassette holder.

Moisture Condensation Warning

Moisture may form inside this unit under the following conditions:

• Immediately after a heater is turned on.

• In a steamy or humid room.

• When this unit is suddenly moved from a cold to warm environment.

If moisture forms inside this unit, it may not operate properly or damage the video tape. In such case, turn on the power and wait for more than 2 hours for the moisture to evaporate.

About Copyright

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Symbols Used in This Manual

The following symbols appear in some headings in this manual.

: Description refers to playback or recording of

video cassette tapes.

Description refers to playback of DVD-Video discs.

: Description refers to playback of Audio CDs.

Note to CATV system installer

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building, as close to the point of cable entry as practical.

Manufactured under license from Dolby Laboratories.

“Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Hint

• Remember to read the instructions along with the video head cleaner before use.

• Clean video heads only when problems occur.

Precautions

–

About the Video Cassettes and Discs

Playable Discs

Unplayable Discs

NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / DVD-Audio / CD-i / Photo CD / Video CD / DVD with region codes other than 1 or ALL /DTS-CD / DVD-ROM for personal computers / CD-ROM for personal computers

On the following disc, the sound MAY NOT be heard.

Super Audio CD NOTE: Only the sound recorded on the normal CD layer can be delivered.

The sound recorded on the high density Super Audio CD layer cannot be delivered.

Any other discs without compatibility indications

Playable Video Cassettes

Use only cassettes marked with this unit.

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: This unit conforms to the NTSC color system. Discs recorded in other color systems such as PAL cannot be played back. *2: Certain DVD-Video discs do not operate as described in this manual due to the intentions of the disc’s producers. *3: Scratched or stained discs may not be played back. *4: Some discs cannot be played back because of incompatible recording conditions, characteristics of the recorder or spe-

cial properties of discs.

*5: You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not play them

back. Even if they are played back, the sound or video quality will be compromised.

*6: You may play back the unfinalized DVD-R/RW disc recorded in the video format on our brand’s DVD recorder. However,

depending on the recording status of a disc, the disc may not be played back at all or normally (the picture or sound may not be smooth, etc.). In this case, you need to finalize the disc with the DVD recorder. Refer to the manual accompanying the DVD recorder.

*7: Only the discs recorded in the video format and finalized can be played back.

Unfinalized discs cannot be played back. Depending on the recording status of a disc, the disc may not be played back at all the picture or sound may not be smooth, etc.

*8:

If the recorded portion of the disc is too small (less than 2 3/16 inches (55 mm) across), it may not play back properly. *9: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it correctly. *10: Discs Recorded in the VR (Video Recording) format cannot be played back.

Playable

discs

Mark (logo) Region code

Recorded

signals

Disc

size

Disc types

DVD-Video

*1, 2, 3, 5, 9

Digital video

(MPEG2)

12 cm

8 cm

Example

Title 1 Title 2

Chapter 1 Chapter 2 Chapter 1

Chapter 2

Chapter 3 Chapter 4

DVD-RW

DVD-R

*1, 3, 4, 5, 6,

8, 9, 10

DVD+RW

DVD+R

*1, 3, 4, 5, 7,

8, 9, 10

Audio CD

*3, 5, 9

Digital audio

12 cm

8 cm

Example

Track 1 Track 2 Track 5

Track 6

Track 3

Track 4

CD-RW

CD-R

*3, 4, 5, 8, 9

is a trademark of DVD Format/Logo Licensing Corporation.

Setup

–

SETUP > QUICK>

DOLBY DIGITAL

Connecting to a Dolby Digital decoder for Dolby Digital audio output.

BITSTREAM

Connecting to the other equipment (an MD deck or DAT deck etc.) without Dolby Digital decoder.

PCM

Connection

Setting

Hint for Cable Box or Satellite Box

L R

VCRDVD/VCR

AUDIO OUT

DIGITAL

AUDIO OUT

AUDIO

OUT

DVD

S-VIDEO

OUT

COMPONENT

VIDEO OUT

Stereo system

Method 1

Analog audio input jacks

AUDIO OUT (Analog)

Connection to an Audio System

Audio cable

(supplied)

* To complete these settings, refer to pages 20-21.

Hint

• The audio source on a disc in a Dolby Digital Multi channel surround format cannot be recorded as digital sound by an MD or DAT deck.

• By hooking this unit up to a Multi channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital Multi channel surround sound as heard in the movie theaters.

• Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

(DVD mode only)

Digital audio input jack

DIGITAL AUDIO OUT

Method 2

Dolby Digital decoder,

MD deck or DAT deck

Setup

If channel 3 has been already occupied for broadcasting,

1) Set your TV to channel 4.

2) Insert a pre-recorded tape into this unit.

3) Press [OUTPUT] on the unit so that the

VCR OUTPUT light is lit.

•

If noise appears on the TV screen, press [VCR/TV] on the remote control.

4) Press [PLAY B] once.

5) After a few seconds, press and hold

[PLAY B] on the unit for 3 seconds.

• The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

• When a picture does not appear on the TV screen, repeat step 4.

6) Press [STOP C] to stop playback.

RF Output Channel

Connections

Hint

• The RF output channel does not change when you adjust tracking during playback. In case RF output channel changes, you can easily switch it back just start the playback again then press and hold [PLAY B] on the unit for 3 seconds.

Select this connection when you want to view or record a scrambled channel. With this connection, channels cannot be changed on the unit. You can view or record ONLY the channels you have selected on the cable box or the satellite box.

•

While you are recording, only the recorded channel can be viewed.

To select channels of the cable box or satellite box

1) Turn on the unit by pressing [POWER], then press [VCR/TV]. The POWER indicator on the front panel will

light, then press [SKIP/CH. G/K, H/L] to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).

• If you use the channel 4, you need to change the unit’s

RF output to channel 4. Refer to “RF Output Channel”.

2) At the TV, select channel 3 or 4 (the same channel as you have selected at step 1).

3) On the cable box or satellite box, select the channel you want to view or record.

ANT-OUT

ANT-IN

RF cable

(supplied)

(Back of DVD/VCR)

(Back of TV)

Satellite or

Cable TV

signal

(Cable box or

Satellite box)

Please refer to “Basic TV Connection” on the front page before you use this unit.

Hint

• Playing a DVD using incorrect settings may generate noise distortion and may also damage the speaker.

Audio

DVD/VCR

DIGITAL

AUDIO OUT

COAXIAL

AUDIO

OUT

DVD

S-VIDEO

OUT

COMPONENT

VIDEO OUT

COAXIAL

Audio Coaxial

Digital cable

(commercially

available)

Setup

–

Admiral: AUX Curtis Mathis: LINE1, LINE2, 00, 90, 91, 92, 93 GE: INPUT, TV/VCR, 00, 90, 91, 92, 93 Hitachi: INPUT, AUX JVC: VIDEO, VIDEO1, VIDEO2, VIDEO3 Kenwood: AUX LXI-Series: 00 Magnavox: AUX CHANNEL

Panasonic: TV/VIDEO RCA: INPUT, TV/VCR, 00, 90, 91, 92, 93 Samsung: TV/VIDEO Sanyo: VIDEO Sharp: 00 Sony: VIDEO1, VIDEO2, VIDEO3 Toshiba: TV/GAME Zenith: 00

DIGITAL

AUDIO OUT

COAXIAL

ANT-OUT

ANT-IN

AUDIO OUT

DVD VCR

DVD/VCR

S-VIDEO

OUT

COMPONENT VIDEO OUT

AUDIO IN

VIDEO IN

AUDIO OUT

VIDEO OUT

AUDIO IN

L R

VCRDVD/VCR

AUDIO OUT

DIGITAL

AUDIO OUT

AUDIO

OUT

DVD

S-VIDEO

OUT

COMPONENT

VIDEO OUT

CB/ PB

CR/ PR

VIDEO IN

VCRDVD/VCR

VIDEO OUT

S-VIDEO IN

DIGITAL

AUDIO OUT

COAXIAL

AUDIO

OUT

DVD

S-VIDEO

OUT

COMPONENT VIDEO OUT

DIGITAL

AUDIO OUT

COMPONENT

VIDEO IN

COAXIAL

AUDIO

OUT

DVD

S-VIDEO

OUT

COMPONENT

VIDEO OUT

AUDIO OUT

(Analog)

VIDEO OUT

Method 1

Good picture

Basic Audio

Method 2

Method 3

Better picture

Best picture

S-VIDEO OUT

COMPONENT VIDEO OUT

Video cable

(supplied)

Audio cable

(supplied)

S-Video cable (commercially

available)

Component Video cable (commercially available)

DVD/VCR

Connection to a TV

Hint

• Connect this unit directly to the TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted due to the copy protection system.

• The COAXIAL, DVD AUDIO OUT, S-VIDEO OUT and COMPONENT VIDEO OUT jacks are only useful in DVD mode.

After you have completed connections

Press the input selector button (usually TV/VIDEO, INPUT or AUX) on your TV to switch an appropriate external input channel (usually near channel 0) for viewing the picture from this unit. If the picture does not appear, also refer to the manual accompanying your TV.

INPUT MODES FOR COMMON TV BRANDS

Listed below are inputs for common brand name TV’s.

Setup

–

Turn on the TV and set it to channel 3.

•

If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section on page 6.

Select your language in the first time you turn on this unit. Then press [B] to go to next step.

Press [B] to start Auto Set Up.

POWER

Press [MENU] and select “CHANNEL SET UP”. Then press [B] to go to next step.

Select “MANUAL SET UP”. Then press [B] to go to next step.

Select the channel to be added or deleted.

Select “ADD” or “DELETE”.

To exit the menu

Press [MENU] and select “CLOCK SET”. Then press [B] to go to next step.

Select the current month. Then press [B] to go to next step.

Select the current day. Then press [B] to go to next step.

Select the current year. Then press [B] to go to next step.

Select the current hour. Then press [B] to go to next step.

Select the current minute. Then press [B] to go to next step.

Select “AM” or “PM”.

To exit the CLOCK SET screen

To Preset the Channel Again

1) Press [MENU] until the main menu appears.

Select “CHANNEL SET UP” by using

[K//L]

, then press

[B]

Select “AUTO SET UP” by using [K//L], then press [B]. After scanning, the tuner stops on the lowest memorized channel.

To Change the On-Screen Language

Press

[MENU]

until the main menu appears.

2) Select “LANGUAGE SELECT” by using [K/L], then press [B].

3) Select “ENGLISH” , “FRANCAIS” or “ESPAÑOL” by using [K/L] then press [CLEAR/C.RESET].

To Select a Channel

You can select a channel by using the Number buttons or [

SKIP/CH. G/K, H/

L].

Notes for using the Number buttons:

• When selecting cable channels which are higher than 99, enter channel numbers as a three-digit number. (for example: 117, press [1], [1], [7])

• You must precede single-digit channel numbers with a zero. (for example: 02, 03, 04 and so on)

• If the clock is not set, the CLOCK SET screen appears when

you press [MENU]. In this case, go to step 2.

CLEAR/

C. RESET

Preparation for Use

Hint

• Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.

No Please wait for a few minutes. After scanning...

• The tuner stops on the lowest memorized channel.

• You can select only the channels memorized in this unit by using [SKIP/CH. G///K, H//L] (or [CHANNEL K///L]).

• If “AUTO SET UP” appears on the TV screen again, check the cable connections. Then, press [B] once again.

Yes Press [MENU] to exit.

•

Refer to “Hint for Cable Box or Satellite Box” section on page 6.

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

Hint

• To go back one step, press [s] (during steps 2 to 7).

• Your clock setting will be lost if either there is a power failure or this unit has been unplugged for more than 30 seconds.

• If the clock is not set, the “CLOCK SET” screen appears

when you press [MENU]. In this case, press [MENU] again.

LANGUAGE SELECT

B ENGLISH [ON] FRANCAIS ESPAÑOL

CH 01

AUTO SET UP

- M E N U -

TIMER PROGRAMMING AUTO REPEAT [OFF] B CHANNEL SET UP CLOCK SET LANGUAGE SELECT

CHANNEL SET UP

AUTO SET UP B MANUAL SET UP

MANUAL SET UP

CHANNEL 30 (CATV)

ADD

MANUAL SET UP

CHANNEL 30 (CATV)

DELETE

- M E N U -

TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT

CLOCK SET

MONTH DAY YEAR 1 0 / – – – – – –

HOUR MINUTE AM/PM – – : – – – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 – – – –

HOUR MINUTE AM/PM – – : – – – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 2 0 0 6

HOUR MINUTE AM/PM – – : – – – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM 0 5 : – – – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM 0 5 : 4 0 – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM 0 5 : 4 0 P M AM B PM

YES

Turn on the Unit for the First Time

VCR

Clock Setup

VCR

Operations described in this manual are mainly based on the remote control.

Hint

• If you accidentally select Spanish or French and need English: Press [MENU] and choose SELEC. IDIOMA or SELECTION LANGUE. Press [B] and select ENGLISH. Finally, press [CLEAR/C.RESET].

•

To add or delete channels in this unit, [SKIP/CH. G/K, H/L] button works on the channel number memorized in this unit, [K/L] works on all.

To Add or Delete Channels

VCR

Setup

–

Function Overview

You must select which component you wish to operate with [OUTPUT] at first, as this product is a combination of a VCR and a DVD player.

CHANNEL

OPEN/CLOSE

VCR DVD DVD IN

SKIP H

STOP PLAY

G SKIP

REV FWD

OUTPUT

DVDVCR

OUTPUT button

DVD OUTPUT light

VCR OUTPUT light

DVD button

VCR button

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

REC/OTR

SETUP TOP MENU

MODE ZOOM

SUBTITLE

T-SET

ANGLE

ENTER

RETURN

SEARCH MODE

REPEAT A-B

OPEN/CLOSE

/EJECT

SPEED AUDIO

CLEAR/

C. RESET

1 2 3

4 5 6

7 8 9

+10

VCR MODE

Press [VCR] on the remote control.

(Verify that the VCR OUTPUT light is lit.)

DVD MODE

Press [DVD] on the remote control.

(Verify that the DVD OUTPUT light is lit.)

Hint

• Pressing only [OUTPUT] on the front panel DOES NOT switch the

mode of the remote control. You MUST select the correct mode on the remote control.

VCR / DVD Switching

Front Panel Indicator

Front & Rear Terminals

6: VIDEO IN jack

Connect a cable coming from the video out jack of a camcorder,

another VCR or an audio-visual source (laser disc player, video disc player, etc.) here.

7: DVD/VCR VIDEO OUT jack

Connect the supplied video cable here through the video in jack of a

television.

8: COMPONENT VIDEO OUT jacks

Connect optional COMPONENT VIDEO cable here through the

COMPONENT VIDEO in jacks of a television. (DVD only)

9: S-VIDEO OUT jack

Connect an optional S-VIDEO cable here through the S-VIDEO in

jack of a television. (DVD only)

10: DIGITAL AUDIO OUT COAXIAL jack

Connect an optional coaxial digital audio cable here through the

coaxial digital audio in jack of a decoder or audio receiver. (DVD only)

CHANNEL

STOP

REV FWD

SKIP H G SKIP

OUTPUT

DVD DISC IN

OPEN/CLOSE

PLAY

STOP/EJECT PLAY REC/OTR

VCR

POWER

F.FWDREW

Lights up when the inserted disc is being played back. Blinks when an unacceptable disc is inserted.

Lights up when the Timer Recording or an OTR recording has been set.

Lights up during a recording. Blinks when a recording is paused.

Lights up when the disc is inserted.

Lights up when power is on.

Lights up when this unit is in the DVD mode.

Lights up when this unit is in the VCR mode.

DIGITAL

AUDIO OUT

COAXIAL

ANT-OUT

ANT-IN

ANT-OUT

ANT-IN

AUDIO OUT

DVD VCR

DVD/VCR

S-VIDEO

OUT

COMPONENT VIDEO OUT

AUDIO IN

VIDEO IN

AUDIO OUT

VIDEO OUT

CB/ P

CR/ P

DIGITAL

AUDIO OUT

COAXIAL

AUDIO

OUT

DVD

DVD/VCR

VCR

S-VIDEO

OUT

COMPONENT

VIDEO OUT

AUDIO OUT

VIDEO OUT

AUDIO IN

VIDEO IN

CHANNEL

STOP

REV FWD

SKIP H G SKIP

OUTPUT

DVD DISC IN

OPEN/CLOSE

PLAY

STOP/EJECT PLAY REC/OTR

VCR

POWER

F.FWDREW

[Rear Panel]

[Front Panel]

1: DVD AUDIO OUT (analog) jacks

Connect the supplied audio cable here through the audio in jacks of

a television or other audio equipment. (DVD only)

2: DVD/VCR AUDIO OUT jacks

Connect the supplied audio cable here through the audio in jacks of

a television or other audio equipment.

3: AUDIO IN jack

Connect audio cable coming from the audio out jack of a camcorder,

another VCR or an audio source here.

4: ANT-IN jack

Connect your antenna or cable box here.

5: ANT-OUT jack

Connect the supplied RF cable to the antenna input jack of a television.

8 7 6

Setup

–

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

REC/OTR

SETUP TOP MENU

MODE ZOOM

SUBTITLE

T-SET

ANGLE

ENTER

RETURN

MODE

REPEAT A-B

OPEN/CLOSE

/EJECT

SPEED AUDIO

CLEAR/ C. RESET

1 2 3

4 5 6

7 8 9

+10

Installing the Batteries for the Remote Control

Install two AA batteries (supplied) matching the polarity indicated inside battery compartment of the remote control.

Keep in mind the following when using the remote control:

• Make sure that there is no obstacle between the remote control and the remote sensor on the unit.

• The maximum operable ranges from the unit are as follows.

- Line of sight: approx. 23 feet (7m)

- Either side of center:

approx. 16 feet (5m) within 30°

- Above:

approx. 16 feet (5m) within 15°

- Below:

approx.

10 feet (3m) within 30°

Remote Control

Hint

• Do not mix alkaline and manganese batteries.

• Do not mix old and new batteries.

DVD mode VCR mode

1 2 3

4 5 6

7 8 9

+10

• To select chapter or title directly.

• To select track directly.

• To select channel.

• The +10 button has no effect in VCR mode.

•

To search forward/backward through a disc.

•

To begin slow forward/reverse playback in the pause mode.

• To search forward/backward through a disc.

• To forward/backward a tape.

A-B

• To repeat between your chosen point A and B.

•

To repeat between your chosen

point A and B.

ANGLE

• To select camera angles on a disc.

AUDIO

• To select audio languages on a disc.

• To select STEREO, L-ch or R-ch.

CLEAR/

C. RESET

• To clear the markers.

• To clear the numbers entered incorrectly.

• To cancel the point for A-B repeat.

• To clear the markers.

• To remove status number in program input.

• To clear the numbers entered incorrectly.

• To cancel the point for A-B repeat.

• To exit the VCR Menu.

• To reset the tape counter.

DISPLAY

• To display the current disc mode.

• To display the current time, tape counter, and channel.

DVD

•

To select the DVD output mode.

• To activate the remote control in DVD mode.

• To select the DVD output mode.

• To activate the remote control in DVD mode.

ENTER

• To move the cursor and determine its position.

• To select an item on the VCR Menu.

•

To advance to the

next VCR Menu.

•

To go back one

step during clock and timer setting.

• To call up the Menu on a disc.

• To call up the VCR Menu.

MODE

• To set black level on/off.

• To set virtual surround on/off.

• To arrange the playing order or play randomly.

• To set virtual surround on/off.

OPEN/CLOSE

/EJECT

• To open or close the disc tray.

• To eject the video cassette from the VCR.

PAUSE

• To pause disc playback.

• To advance playback one frame at a time.

• To pause disc playback.

• To pause tape playback or recording.

• To advance playback one frame at a time.

PLAY

• To begin disc playback. • To begin disc playback. • To begin tape playback.

POWER

• To turn the unit on/off. • To turn the unit on/off. • To turn the unit on/off.

REC/OTR

• To start a recording or One Touch Recording.

REPEAT

• To play a chapter or title repeatedly.

• To play a track or disc repeatedly.

RETURN

• To return to the previous operation in menu.

MODE

• To search chapter, title or time.

•

To set or search the markers.

• To search track.

• To search time.

• To set or search the markers.

• To call up the index or time search menu.

SETUP

• To call up the DVD setup menu.

SKIP/CH.

• To skip chapters or titles. • To skip tracks.

• To change channels.

• To adjust the tracking manually during playback.

SLOW

• To view the tape in slow motion.

SPEED

• To select the recording speed.

STOP

• To stop playback. • To stop playback.

• To stop playback or recording.

SUBTITLE

T-SET

• To select subtitles on a disc.

•

To put the VCR into standby mode for a Timer Recording.

TOP MENU

• To call up the Top Menu on a disc.

VCR

• To select the VCR output mode.

• To activate the remote control in VCR mode.

VCR/TV

• To select DVD position or TV position.

• To select CD position or TV position.

• To select VCR position or TV position.

ZOOM

• To magnify part of a picture. (x2/x4)

Button (Alphabetical order)

Disc/Tape

VCR Functions

–

Press [SEARCH MODE] once.

To select Index Mark

After searching, it automatically starts playback.

Press [SEARCH MODE] twice.

Select the desired length of time for fast forwarding or rewinding.

After searching, it automatically starts playback.

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

OPEN/CLOSE

/EJECT

SPEED AUDIO

1 2 3

4 5 6

7 8 9

+10

Insert a video

cassette into this unit.

2 To start playback

3 To stop playback 4

To eject the cassette

Hint

• When a tape without record tab is inserted, the unit will start playback automatically.

• Tracking will be automatically adjusted upon playback. To adjust the tracking manually, press [SKIP/CH.

G/K, H/L] (or [

CHANNEL K/L]

Playback

Before: Turn on the TV and set it to channel 3.

• If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section on page 6.

PLAY

STOP

OPEN/CLOSE

/EJECT

Other Operations

Hint

• Still/Slow mode will be automatically canceled after 5 minutes to prevent damage to the tape and the video head.

• To return to playback from the Picture Search/Still/Slow mode, press [PLAY B].

VCR Functions

You can skip the program backward and forward by the Index Mark.

Index Search

MODE

Pro.1 Pro.2 Pro.3 Pro.4 Pro.5

02 01 01 02 03

Beginning of the tape

End of the tape

CURRENT PROGRAM

INDEX MARK

PLAYB

Hint

•

The Index Mark will be made automatically at the beginning of each recording.

• The time gap between Index Marks should be greater then 1 minute for SP mode, 2 minutes for LP mode and 3 minutes for SLP mode.

To rewind

To fast forward

Hint for Index Search & Time Search

• These functions are not available during recording.

• Press [STOP C] to stop the search.

• If a tape ends during a search, your search will be canceled and the tape will rewind to the beginning.

Time Search

You can search backward and forward a specific length of time on a tape.

INDEX SEARCH – –

MODE

TIME SEARCH – : – –

PLAYB

(1 minute~9 hours and 59 minutes)

To rewind

To fast forward

To cue or review picture during playback (Picture Search)

Use [g] or [h ]([ F.FWD g] or [REW h]).

• Press it again and the unit will search in super high speed. (in the SLP mode only)

To freeze the picture on TV screen during playback (Still mode)

Press [PAUSE F]. Each time you press the button, the picture will be forwarded by one frame.

•

If the picture begins to vibrate vertically in the still mode, stabilize the picture by using

[SKIP/CH. G/K, H/L] (or

[

CHANNEL K/L]).

• If the picture is distorted or rolling vertically, adjust the vertical hold control on your TV if equipped.

Counter Reset

Press [CLEAR/C.RESET].

To play back in slow motion (Slow mode)

Press [SLOW] during playback or the still mode.

• If the noise bars appear on the TV screen, you can reduce it

by using [SKIP/CH. G/K, H/L] (or [

CHANNEL K/L]

Auto Rewind

When a tape reaches its end during playback, fast-forward or recording (except Timer Recording and One Touch Recording), the tape will automatically rewind to the beginning. After rewinding finishes, the unit will eject the tape.

VCR

• Insert a tape into this unit.

VCR

• Insert a tape into this unit.

INDEX SEARCH 0 3

01 ~ 20

TIME SEARCH 2 : 5 0

0:01~ 9:59

CHANNEL

STOP

REV FWD

SKIP H G SKIP

OUTPUT

DVD DISC IN

OPEN/CLOSE

PLAY

STOP/EJECT PLAY REC/OTR

VCR

POWER

F.FWDREW

3 4

VCR Functions

–

Press [MENU], then select “TIMER PROGRAMMING”.

Select an empty program number. Then press [B] to go to next step.

Select “ONCE”, “DAILY” (Mon-Fri), or “WEEKLY”. Then press [B] to go to next step.

Press [B] to set “AUTO REPEAT”, “ON” or “OFF”.

Select the desired date. Then press [B] to go to next step.

Select the desired start time (hour). Then press [B] to go to next step.

Insert a cassette with

tab into this unit.

2 Select the channel

to record.

Press [SPEED] to select the desired tape speed.

4 Press [REC/OTR] repeatedly to select the

desired recording length.

5 To stop recording 6 To eject the

recorded cassette

• You can set a program one year in advance.

Recording

REC

Type of tape

T60 T120 T160 SP mode 1hour 2hours 2-2/3hours SLP mode 3hours 6hours 8hours

Recording/Playback TimeTape Speed

1 2 3

4 5 6

7 8 9

REC OTR(0:30) OTR(1:00).....

(Normal recording)

OTR(8:00) OTR(7:30)

PLAY

STOP

OPEN/CLOSE

/EJECT

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

REC/OTR

SETUP TOP MENU

ENTER

RETURN

OPEN/CLOSE

/EJECT

SPEED AUDIO

1 2 3

4 5 6

7 8 9

+10

SKIP/CH.

You CAN NOT dub a DVD to a videotape.

To stop recording temporarily (Pause mode)

Press [PAUSE F].

• During the rec-pause mode, five C marks appear on the TV screen. Each C mark represents one minute.

• Press it again to resume recording.

• Pause mode will be automatically canceled after 5 minutes to prevent damage to the tape and the video head.

Recording & OTR (One Touch Recording)

- M E N U -

TIMER PROGRAMMING B AUTO REPEAT [ON] CHANNEL SET UP CLOCK SET LANGUAGE SELECT

Auto Repeat

Hint

• To cancel Auto Repeat, follow step 1 above. Then, press [B] so that “OFF” appears beside “AUTO REPEAT”. Press [CLEAR/C.RESET] to exit.

• If menu remains on the TV screen after step 2, press [CLEAR/C.RESET] to exit.

• The Auto Repeat playback will start automatically if you set “AUTO REPEAT” to “ON” in the stop mode.

PROGRAM NUMBER 1 DATE – – / – – START TIME – – : – – – – END TIME – – : – – – – CHANNEL – – REC SPEED – –

Timer Recording

Hint

• If you want to watch one channel while recording another...

1) Press [VCR/TV] to put the unit in TV position.

2) Select a channel you want to watch with the cable box or the satellite box.

SPEED

REC/OTR

TIMER PROGRAMMING

PROG 12345678 DATE START TIME END TIME CHANNEL REC SPEED

Press [MENU] and select “AUTO REPEAT” during playback.

- M E N U -

TIMER PROGRAMMING B AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT

ONE TIME PROGRAM

PROGRAM NUMBER 1 DATE 1 0 / 2 3 MON START TIME 0 7 : 3 0 – – END TIME – – : – – – – CHANNEL – – REC SPEED – –

ONE TIME PROGRAM

PROGRAM NUMBER 1 DATE 1 0 / 2 3 MON START TIME – – : – – – – END TIME – – : – – – – CHANNEL – – REC SPEED – –

Before:

Turn on the TV and set it to channel 3.

•

If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section on page 6.

- M E N U -

B TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT

PROGRAM NUMBER 1 B ONCE

DAILY WEEKLY

VCR

•

Insert a tape with its record tab into the unit.

Available program number flashes.

This function will playback a tape repeatedly from the beginning when the tape reaches the end.

CHANNEL

STOP

REV FWD

SKIP H G SKIP

OUTPUT

DVD DISC IN

OPEN/CLOSE

PLAY

STOP/EJECT PLAY REC/OTR

VCR

POWER

F.FWDREW

5 624

Accidental erasure prevention

To prevent accidental recording on a recorded cassette, remove its record tab. To record on it later, cover the hole with adhesive tape.

Record tab

VCR Functions

–

Press [SUBTITLE/T-SET] to set timer standby mode.

• indicator on the front panel lights up. The unit will change to the DVD mode.

Select “AM” or “PM”. Then press [B] to go to next step.

Repeat the procedure in steps 5 and 6 to set the end time.

Select the desired channel. Then press [B] to go to next step.

• If you have connected the unit to a cable box or satellite

box as the connection on page 6, select the VCR to channel 3 or 4 (the RF output channel of the VCR). Then,

select the desired channel at the cable box or satellite box. Leave the cable box or satellite box on for Timer Recording.

Select the desired recording speed, then press [CLEAR/C.RESET].

• To set another program after step 9, press [B]. Then, continue with step 2.

Hint

• To go back one step, press [s] during steps 3 to 9.

To Check, Correct or Cancel a Timer Program

1) Press [SUBTITLE/T-SET] then, [VCR] on the remote

control.

2) Select main menu by pressing [MENU].

3) Select “TIMER PROGRAMMING” by using [K/L], then press [B].

4) Select the program number which you want to check by using [K/L]. The details of the program you selected will appear on the TV screen.

• Go to the digit you want to change by using [s / B]. Then, enter correct numbers by using [K/L].

• You may cancel the entire program by pressing [s] while the program number blinks.

5) Press [CLEAR/C.RESET] to exit.

6) Press [SUBTITLE/T-SET] to return to timer standby mode.

To cancel a Timer Recording in progress

Press [STOP/EJECT C A] on the unit.

ONE TIME PROGRAM

PROGRAM NUMBER 1 DATE 1 0 / 2 3 MON START TIME 0 7 : 3 0 PM END TIME – – : – – – – CHANNEL – – REC SPEED – – AM B PM

ONE TIME PROGRAM

PROGRAM NUMBER 1 DATE 1 0 / 2 3 MON START TIME 0 7 : 3 0 PM END TIME 0 8 : 3 0 PM CHANNEL 1 6 REC SPEED SP B SP SLP

SUBTITLE

T-SET

Hints for OTR and Timer Recording

ONE TIME PROGRAM

PROGRAM NUMBER 1 DATE 1 0 / 2 3 MON START TIME 0 7 : 3 0 PM END TIME 0 8 : 3 0 PM CHANNEL 1 6 REC SPEED – –

CLEAR/

C. RESET

• Press [VCR] on the remote control before you set Timer Recording. Make sure the remote control is in the VCR mode, then press [SUBTITLE/T-SET].

• If a tape is not in the unit or does not have the record tab, indicator on the front panel blinks and Timer Recording cannot be performed. Please insert a recordable tape.

• When Timer Recordings are set, indicator on the front panel lights up. To use the VCR as usual until the time for the recording, press [SUBTITLE/T-SET] so that indicator lights off. Press [VCR/TV] to choose the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual.

After an OTR or a Timer Recording has been set, this unit operates as follows:

• If a tape runs out before an OTR or a Timer Recording is finished, the unit ejects the tape. Press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then press [VCR] to activate the VCR function again.

• Once the unit turns to the timer standby mode, no VCR functions are available until [SUBTITLE/T-SET] is pressed.

• To cancel the timer standby mode, press [SUBTITLE/T-SET] on the remote control or [STOP/EJECT C A] on the unit, then press [VCR] to activate the VCR function again.

• The mode of the unit and the remote control may differ (VCR mode or DVD mode) when you set Timer Recording or after you canceled Timer Recording. Press [VCR] or [DVD] on the remote control to select your desired mode before you operate.

When an OTR or a Timer Recording is completed...

• If Auto Power Off for DVD has been activated and there are Timer Recordings on standby, the unit turns off automatically, and indicator on the front panel lights to indicate the unit is in the timer standby mode.

• indicator on the front panel flashes if there are no more Timer Recordings on standby.

• If Auto Power Off for DVD has NOT been activated, the unit switches to the DVD mode and all the VCR functions will be unavailable. All the DVD functions are available during OTR, timer standby mode and Timer Recording.

• Press [STOP/EJECT C A] on the front panel or [SUBTITLE/T-SET] on the remote control to use the VCR when the unit is off.

• Press [OUTPUT] on the front panel or [VCR] on the remote control to use the VCR when the unit is on. In case Timer Recording is in standby mode, press [STOP/EJECT C A] on the front panel or [SUBTITLE/T-SET] on the remote control, and then press [OUTPUT] on the front panel or [VCR] on the remote control.

If you want to use the DVD player during a Timer Recording or while indicator on the front panel is on or blinking.

• Press [POWER] to turn on the unit. Press [DVD] on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual.

NOTE (for Timer Recording) :

• If there is a power failure or the unit is unplugged for more than 30 seconds, clock and all timer settings will be lost.

VCR Functions

–

Copying a Video Tape

Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws.

1) Insert a pre-recorded tape into another VCR for playing.

Insert a tape with its record tab into this unit for recording.

3) Press [SPEED] on the remote control of the recording

unit to select the desired recording speed (SP/SLP).

4) Select the “L1” or “L2” position on the recording unit.

• To use the input jacks on the back of this unit, select

“L1” position by pressing [0], [0], [1] on the remote control or [

CHANNEL K/L]

on this unit.

• To use the input jacks on the front of this unit, select

“L2” position by pressing [0], [0], [2] on the remote control or [

CHANNEL K/L] on

this

unit

5) Press [REC/OTR] on the recording unit.

6) Begin playback of the tape in another source.

7) To stop recording, press [STOP/EJECT C A] on the

recording unit, then stop playback of the tape in another source.

Hint

• For best results during dubbing, use the front panel controls whenever possible. The remote control might affect another source’s operation.

• Always use video-quality shielded cables with RCA-type connectors. Standard audio cables are not recommended.

• You can use a video disc player, satellite receiver or other audio/ video component with Audio / Video outputs.

• “L1” or “L2” is found before the lowest memorized channel. (Example: CH02)

• “L2” input jacks are on the front of this unit.

DIGITAL

AUDIO OUT

COAXIAL

ANT-OUT

ANT-IN

AUDIO

OUT

DVD DVD/VCR VCR

S-VIDEO

OUT

COMPONENT

VIDEO OUT

AUDIO OUT

VIDEO OUT

AUDIO IN

VIDEO IN

ANT-OUT

ANT-IN

VCRDVD/VCR

COMPONENT VIDEO OUT

AUDIO IN

VIDEO IN

AUDIO OUT

VIDEO OUT

AUDIO OUT

VIDEO OUT

Connect

Audio/Video cables

(commercially available)

RF cable

(supplied)

(Back of TV)

(Back of DVD/VCR*)

(Back of another source)

Connect

*Front input jacks are also available

DVD Functions

–

DVD

Hint

• Zooming function does not work while the disc menu is showing up.

• x4 zoom is not available on some discs.

• It may take several seconds to slide the zoomed picture.

• The picture may be distorted when you press

[PAUSE k] or [h]

repeatedly in the zoom mode.

• In the zoom mode, it automatically changes

x2(x4) to the

zoomed position guide.

Hint

•

For DVDs, fast forward or reverse search speed is different depending on the disc. Approximate speed is 1(x2), 2(x8), 3(x20), 4(x50), 5(x100).

•

For Audio CDs approximate speed is 1(x2), 2(x8), 3(x30).

Paused and Step-by-Step Playback

DVD

Press [PAUSE F] during playback. To continue playback, press [PLAY B].

DVD

The disc goes forward by one frame each time [PAUSE F] is pressed in the pause mode. To continue playback, press [PLAY B].

Fast Forward / Reverse Search

DVD

Press [h] or [g] repeatedly during playback to select the required forward or reverse speed. To continue playback, press [PLAY B].

To use [SKIP j/REV], [i SKIP/FWD] on this unit

Press and hold to change forward or reverse playback speed. To continue playback, press [PLAY B].

Playback

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

OPEN/CLOSE

/EJECT

SPEED AUDIO

1 2 3

4 5 6

7 8 9

+10

1 2

PLAY

DVD Functions

PLAY

STOP

POWER

OPEN/CLOSE

/EJECT

DVD menu

Some discs contain menus which allow you to customize DVD playback. Press [K / L / s / B ] to select an item, then press [ENTER] (or [PLAY B]).

Calling up a Menu Screen during Playback

• Press [MENU] to call up the DVD menu.

• Press [TOP MENU] to call up the title menu.

Resume

DVD

Press [STOP C] during playback. Resume message will appear on the TV screen. Press [PLAY B], playback will resume from the point at which playback was stopped.

Press 'PLAY' to play from here. To play the beginning, press 'STOP' first and then 'PLAY'.

Resume ON

Hint

• A “prohibited icon” may appear at the top-right on the TV screen when the operation is prohibited by the disc or this unit.

• Some DVDs may be played from title 2 or 3 due to specific programs.

•

During the playback of a two-layered disc, pictures may stop for a moment. This happens while the 1st layer is being switched to the 2nd layer. This is not a malfunction.

Hint

• On DVDs, set “STILL MODE” to “FIELD” in the DISPLAY menu if pictures in the pause mode are blurred. (Refer to pages 20-21.)

Hint

• Slow forward or reverse speed is different depending on the disc. Approximate speed is 1(1/16), 2(1/8), 3(1/2).

• Set “STILL MODE” to “FIELD” in the DISPLAY menu if pictures in the slow playback mode are blurred. (Refer to pages 20-21.)

Zoom

DVD

1) Press [ZOOM] during playback.

2) Press [ZOOM] repeatedly to select the required zoom

factor: x2, x4 or OFF.

x2 x4

Press [K / L / s / B] to slide the zoomed picture across the screen.

4) To exit zoom mode, press [ZOOM] to select OFF.

Before: Turn on the TV, amplifier and any other components which are connected to this unit. Make sure the TV and audio receiver (commercially available) are set to the correct channel.

Insert a disc with

label facing up.

TIP:

You can change the on-screen language for DVD function in “PLAYER MENU” setting. (Refer to page 20.)

Slow Forward / Reverse

DVD

Press [h] or [g] repeatedly in the pause mode to select the required forward or reverse speed. To continue playback, press [PLAY B].

To use [SKIP j/REV], [i SKIP/FWD] on this unit

Press and hold in the pause mode to change forward or reverse playback speed. To continue playback, press [PLAY B].

Hint

• To cancel resume, press [STOP C] one more time in the stop mode.

• The resume information stays on even when the power is turned off.

Hint

• Menu operations may vary depending on the disc. Refer to the manual accompanying the disc for details.

To start playback

To stop playback

To use [SKIP j/REV], [i SKIP/FWD] on this unit

Press once to skip a chapter or track to a desired point.

CHANNEL

STOP

REV FWD

SKIP H G SKIP

OUTPUT

DVD DISC IN

OPEN/CLOSE

PLAY

STOP/EJECT PLAY REC/OTR

VCR

POWER

F.FWDREW

1 4 3

DVD Functions

–

DVD

On-Screen Display

You can check the information about the current disc by pressing [DISPLAY] on the remote control.

DVD

DISPLAY

4/12 0:03:21 - 0:02:15

4/12 0:13:45 - 0:45:40

4/12 0:03:21 - 0:02:15

TR(Track): Current track number / Total tracks

Current repeat setting, if active

T: Track repeat A: All Tracks repeat

A B: A-B repeat

ALL: Current track number / Total tracks

Elapsed time of the current track

Remaining time of the current track

Elapsed time of the entire disc

Remaining time of the entire disc

Current playback status

Hint

• When you are playing a disc in PROGRAM or RANDOM mode, PROGRAM (or RANDOM) will be displayed instead of 2.

CH(Chapter): Current chapter number / Total chapters

TT(Title): Current title number / Total titles

Current repeat setting, appears only when the repeat setting is active.

C: Chapter repeat T: Title repeat

A B: A-B repeat

11/16 0:00:00 - 0:03:30

1/3 0:00:00 - 1:23:45

11/16 0:00:00 - 0:03:30

1/3 0:00:00 - 1:23:45

T L1

BIT RATE: The amount of audio and video data currently being read

Elapsed time of the current chapter

Remaining time of the current chapter

Elapsed time of the current title

Remaining time of the current title

Layer numbers, appears only when playing a two-layered disc. L0: Layer 0 is playing L1: Layer 1 is playing

Current playback status

Angle icon, appears only in a case multi-angel is available on the DVD.

DVD Functions

–

Press [RETURN ].

Press [SEARCH MODE] repeatedly until the marker display appears.

Select the marker.

Press [ENTER] at the desired marker.

Press [SKIP/CH. G/o, H/p] during playback.

Press [SEARCH MODE] repeatedly until the marker display appears.

Select a marker.

Press [ENTER].

Press [SEARCH MODE] repeatedly until the Time Search display appears.

Select a desired disc time by using the Number buttons within 30 seconds.

Press [

SKIP/CH. G/o, H/p

] during playback.

Press [SEARCH MODE] once for the Chapter Search. Press [SEARCH MODE] twice for the Title Search.

Select title/chapter number by using the Number buttons within 30 seconds.

Press [SEARCH MODE].

Select track number by using the Number buttons within 30 seconds.

Search Functions

1:29:00

TOTAL

1 2 3

4 5 6

7 8 9

To return to the marker later

To exit the marker screen

/29

/12

1 2 3

4 5 6

7 8 9

+10

1 2 3

4 5 6

7 8 9

+10

TR 1 TR 2 TR 3 TR 4

Current Track

(TR)

SKIP

Using [SKIP/CH. G/o, H/p]

PLAY

SKIP/CH.

CH 1 CH 2 CH 3 CH 4

Current Chapter

(CH)

SKIP

TT 1 TT2 TT3 TT4

Current Title (TT)

SKIP

Using [SKIP/CH. G/o, H/p]

1:29:00

TOTAL

Hint

• When there is no need to enter a number, “0” appears automatically. For example, “0: 0_: _ _” appears in the Time Search display if the

total time of the title or track is less than 10 minutes.

• Press [CLEAR/C.RESET] to erase the incorrect input at step 2.

Hint

•

The Marker display will disappear in about 30 seconds when there is no output.

• To clear a marker, select the marker to be cleared at step 2 in the section “To set a marker” or “To return to the marker later” and then press [CLEAR/C.RESET].

• Opening the disc tray or turning off the power will erase all markers.

•

Selecting “AC” at step 2 in the section “To set a marker” or “To return to the marker later” will also erase all markers.

MODE

ENTERENTER

RETURN

• For the disc with less than 10 tracks, press the track number directly.

• For discs with more than 10 but less than 99 tracks, to play single-

digit track, press [0] first, then the track number (e.g. for track 3, press [0], [3]). To play a double-digit track, press the track number.

MODE

PLAY

(If the disc has no chapters)

Hint

• [+10] can also bring the Track search display, except for the disc

with less than 10 tracks. For such a disc, track search can be done by just pressing the track number.

MODE

PLAY

SEARCH MODE does not work during Programmed or Random Playback.

MODE

PLAY

SKIP/CH.

Using Track Search

DVD

Using Time Search

DVD

Marker Setup

DVD

This feature allows you to assign a specific point on a disc to be called back later.

To set a marker

Hint

• Depending on the disc being played, this function can also be performed by directly entering the desired chapter number with

the Number buttons. Refer to the manual accompanying the disc.

Using Title / Chapter Search

DVD

DVD Functions

–

Press [MODE] once.

Using [K/L] to select desired track. Press [ENTER].

Press [PLAY B] to start Programmed Playback.

Press [MODE] twice.

Press [PLAY B] to start Random Playback.

Press [A-B] at your desired starting point (A).

Press [A-B] at your desired ending point (B).

Press [REPEAT] during playback.

Repeat / Random / Programmed Playback

A-

A-B

STOP

MODE

PLAY

CD-DA TOTAL 0:45:55

RANDOM PROGRAM

--no indication--

RANDOM

CD-DA TOTAL 0:00:00

CD-DA TOTAL 1:03:30

2/3

1 3:30 5 5:10 10 4:20 11 3:00 12 3:20 17 4:10 22 2:50

• Point B should be in the same title or track as point A.

• Up to 99 tracks can be ordered.

• If eight or more tracks were in a program,

use [SKIP/CH. G///K , H //L] to see all the tracks.

Hint

• Repeat setting will be cleared when moving to another title, chapter or track.

• Repeat playback are not available with some discs or during repeat A-B playback.

Hint

• Press [CLEAR/C.RESET] at step 2 to erase the most recently

entered track.

• To erase all programmed tracks at once, select “ALL CLEAR’’ and

press [ENTER] at step 2.

• While a program is being played back, [STOP C] works as follows; ⇒

Press [STOP C] and [PLAY B] next, so that the programmed playback restarts.

⇒ Press [STOP C] twice and [PLAY B] next, so that playback

restarts from the first track in the original order. However, your programmed playback can be restarted when you follow the above steps. (Your programs are still stored until either the disc tray is open or power is turned off.)

• To repeat the current track in the program, press [REPEAT]

repeatedly until “ TRACK’’ appears during playback.

• To repeat the entire program, press [REPEAT] repeatedly until

“ ALL’’ appears during playback.

Hint

• To repeat the current track in the random selections, press

[REPEAT] repeatedly until “ TRACK” appears during playback.

• To repeat the entire random selections, press [REPEAT] repeat-

edly until “ ALL” appears during playback.

• During random playback, you cannot go back to the previous track.

A-B

ENTERENTER

PLAY

MODE

PLAY

STOP

Hint

• To exit the sequence, press [A-B] so that “OFF” appears.

• To cancel point A, press [CLEAR/C.RESET] at step 1.

• This function does not work in the other repeat modes.

PLAY

REPEAT

PLAY

A-B

PLAY

Repeat Playback

DVD

Repeat function is available only during playback.

Programmed Playback

DVD

You may determine the order in which tracks will play.

Random Playback

DVD

This function shuffles the playing order of tracks instead of playback in the sequence.

Repeat A-B Playback

DVD

Repeat function is available only during playback.

OFF

(repeat off)

CHAPTER

(current chapter repeat)

TITLE

(current title repeat)

Each time you press [REPEAT] repeat function changes as example below.

OFF

(repeat off)

TRACK

(current track repeat)

ALL

(entire disc repeat)

DVD Functions

–

RETURN

Press [MODE] twice (once for CD) during playback.

Press [ENTER] for the desired effect.

Press [RETURN ] to exit.

Press [AUDIO] during CD playback.

Press [ANGLE] during playback.

Press [MODE] during playback.

Press [ENTER] to adjust the black level.

Press [RETURN ] to exit.

Press [AUDIO] to change audio language.

Press [SUBTITLE/T-SET] during playback.

Press [B] to select subtitle ON or OFF.

Press [SUBTITLE/T-SET] during playback.

Special Settings

1.ENG Dolby D 3/2.1ch 48k/3

Each time you press [AUDIO], audio language changes as example below.

STEREO

(right and left channels are active)

L-ch

(left channel is active)

R-ch

(right channel is active)

This unit allows you to select a sound mode during CD playback.

STEREO

Each time you press [AUDIO], sound mode changes as example below.

Each time you press [SUBTITLE/T-SET], subtitle language changes as example below.

1 / 8

OFF

Adjust the Black Level Setting to make the dark areas of the TV picture brighter.

OFF

1: Natural effect 2: Emphasized effect OFF: No effects (original sound)

To set subtitle ON/OFF

1.ENG/6

OFF

Hint

•

If your language is not shown after pressing [SUBTITLE/T-SET] several times, the disc may not have that language. However, some discs allow subtitle language setting on the disc menu. (Operation varies depending on the discs, so refer to the manual along with the disc.)

• When “NOT AVAILABLE” appears on the TV screen, it means no subtitle is recorded on the scene.

• If you choose a language that has a three-letter-language code, the code will be displayed every time you change the subtitle language setting. If you choose any other languages, ‘---’ will be displayed instead. (Refer to page 24.)

• Some discs will only allow you to change the subtitle from the disc menu. Refer to the manual accompanying the discs for details.

Hint

For CD play back only

• Virtual Surround will not be effective if the sound mode is set to something other than STEREO. Refer to “Stereo Sound Mode”.

• When playing back 96kHz with Virtual Surround function, the sound will be down sampling at 48kHz and output as digital audio.

ANGLE

PLAY

MODE

ENTERENTER

RETURN

Hint

• Some discs will only allow you to change the audio setting from the disc menu. Refer to the manual accompanying the discs for details.

•

When “OFF” appears on the TV screen, it means audio language is not available.

• If your language is not shown after pressing [AUDIO] several times, the disc may not have that language. However, some discs allow audio language setting on the disc menu. (Operation varies depending on the disc, so refer to the manual along with the disc.)

OFF

(no subtitles)

ENG

(English subtitles)

FRE

(French subtitles)

...

ENG

(English audio)

SPA

(Spanish audio)

FRE

(French audio)

...

1.ENG/6

SUBTITLE

T-SET

PLAY

SUBTITLE

T-SET

PLAY

AUDIO

PLAY

AUDIO

PLAY

MODE

PLAY

ON: Makes the dark areas brighter. OFF: Shows the original picture as recorded.

Subtitle Language

DVD

This unit allows you to select a subtitle language (if available) during DVD playback.

Camera Angle

DVD

Some DVD discs may contain scenes which have been shot simultaneously from various angles. You can change the camera angle if the angle icon appears on the screen. If the “ANGLE ICON” setting is “OFF” in the OTHERS menu, the angle icon will not appear. (Refer to pages 20-22.)

Stereo Sound Mode

DVD

Black Level Setting

DVD

Virtual Surround

DVD

You can enjoy stereophonic virtual world on your existing 2 channel stereo system.

Audio Language

DVD

This unit allows you to select an audio language (if multiple languages are available) during DVD playback.

DVD Functions

–

ENTERENTER

CUSTOM Menu

SETUP

PLAY

STOP

ENTERENTER

Hint

∗1

• Language options are not available with some discs.

• If OTHER is selected in the AUDIO, SUBTITLE or DISC MENU screen, press four-digit number to enter the code for the desired language. (Refer to the language code list on page 24.)

• Only the languages supported by the disc can be selected.

∗2

• Language setting for Audio and Subtitle are not available with some discs. Then press [AUDIO] and [SUBTITLE/T-SET]. Details are on page 19.

LANGUAGE Setting

Follow steps 1 to 3 in the “CUSTOM Menu” section above.

Select the desired item.

AUDIO: ∗1 ∗2 (Default: ORIGINAL)

Sets the audio language.

SUBTITLE: ∗1 ∗2 (Default: OFF)

Sets the subtitle language.

DISC MENU: ∗1 (Default: ENGLISH)

Sets the language in DVD menu.

PLAYER MENU

QUICK

(Default: ENGLISH)

Sets the language for the On-Screen Display.

ENTERENTER

SETUP

Select the desired item.

PLAY

STOP

SETUP

QUICK SETUP Menu

• Refer to the sections “PLAYER MENU”, “TV ASPECT” or “DOLBY DIGITAL” on page 20 or 21.

You can change the settings of the unit.

•

QUICK

on pages 20-21 indicates DVD Setup menus also accessible from the QUICK SETUP menu.

<SETUP MENU> Confirm that “QUICK” is selected.

You can select the “PLAYER MENU”, “TV ASPECT” or “DOLBY DIGITAL” from the QUICK SETUP menu quickly.

ENTERENTER

LANGUAGE menu

AUDIO menu

DISPLAY menu

OTHERS menu

Select the desired language.

AUDIO ORIGINAL ENGLISH FRENCH

SUBTITLE OFF ENGLISH FRENCH

DISC MENU ENGLISH FRENCH SPANISH

PLAYER MENU ENGLISH FRANÇAIS ESPAÑOL

LANGUAGE menu

DVD Setup

P20 A Step 5 P21 B Step 5 P21 C Step 5

page 20

page 21

page 22

PARENTAL menu

page 22

ENTERENTER

To exit the menu

Select “CUSTOM”.

Select the desired item.

Press [SETUP] in the stop mode.

or or

ENTERENTER

SETUP

QUICK CUSTOM INITIALIZE

SETUP QUICK

PLAYER MENU TV ASPECT DOLBY DIGITAL

ENGLISH 4:3 LETTER BOX BITSTREAM

SETUP LANGUAGE

AUDIO SUBTITLE DISC MENU PLAYER MENU

ORIGINAL OFF ENGLISH ENGLISH

SETUP CUSTOM

LANGUAGE DISPLAY AUDIO PARENTAL OTHERS

SETUP OTHERS

ANGLE ICON AUTO POWER OFFONON

SETUP AUDIO

DRC DOWN SAMPLING DOLBY DIGITAL

ON ON BITSTREAM

SETUP DISPLAY

TV ASPECT STILL MODE

4:3 LETTER BOX AUTO

SETUP LANGUAGE

AUDIO SUBTITLE DISC MENU PLAYER MENU

ORIGINAL OFF ENGLISH ENGLISH

SETUP PARENTAL

PASSWORD

Please enter a 4-digit password.

SETUP

QUICK CUSTOM INITIALIZE

SETUP

QUICK CUSTOM INITIALIZE

DVD Functions

–

Hint

STILL MODE:

• Select “AUTO” usually.

• If you select “AUTO”, automatically select the best resolution setting (FRAME or FIELD) based on the data characteristics of the pictures. (default).

• If you select “FIELD”, the picture in the still mode will be stabilized.

• If you select “FRAME”, the picture in the still mode will be highly defined.

• An individual picture on TV screen is called a “frame”, which consists of two separate images called a “field”.

• Some pictures may be blurred if you select “AUTO” in the still mode due to their data characteristics.

You can change the display functions. Follow steps 1 to 3 in the “CUSTOM Menu” section on page 20.

Select the desired item.

DISPLAY menu

Choose the appropriate audio settings for your equipment. It only affects during the playback of DVD discs. Follow steps 1 to 3 in the “CUSTOM Menu” section on page 20.

Select the desired item.

AUDIO menu

Hint

DRC:

• This function is available only on the discs which are recorded in the Dolby Digital format.

DOWN SAMPLING:

• When playing disc with copyright protection, the sound will be down sampled at 48kHz, even if you set to “OFF”.

•

This function is available only on digital outputting of a disc recorded in 96kHz.

DISPLAY Setting

AUDIO Setting

SETUP

To exit the menu

6 To exit the menu

Hint

TV ASPECT:

• Select “4:3 LETTER BOX”, so that black bars may appear on the top and bottom of the screen.

• Select “4:3 PAN & SCAN” for a full height picture with both sides adjusted.

• Select “16:9 WIDE” if a wide screen TV is connected to this unit.

TV ASPECT:

QUICK

(Default: 4:3 LETTER BOX)

See Hint on the left.

TV ASPECT

4:3

LETTER BOX

4:3

PAN & SCAN

16:9

WIDE

TV ASPECT

4:3 LETTER BOX

STILL MODE

AUTO

ENTERENTER

STILL MODE: (Default: AUTO)

See Hint on the right.

TV ASPECT

4:3 LETTER BOX

STILL MODE

AUTO

STILL MODE

AUTO FIELD FRAME

ENTERENTER

Select the desired setting.

ENTERENTER

DRC (Dynamic Range Control): (Default: ON)

Set to “ON” to compress the range between soft and loud sounds.

DOLBY DIGITAL:

QUICK

(Default: BITSTREAM)

Set to “BITSTREAM” when the unit is connected to a Dolby Digital decoder.

• BITSTREAM: Outputs a Dolby Digital Signals.

• PCM: Convert the Dolby Digital into PCM (2 channel).

DRC ON DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

OFF ON BITSTREAM

DOWN SAMPLING: (Default: ON)

Set to “ON” when outputting in 48kHz. Set to “OFF” when outputting the original sound.

DRC ON DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

OFF ON BITSTREAM

DRC ON DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

ON OFF BITSTREAM

DRC ON DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

ON ON

PCM

DRC ON DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

OFF ON BITSTREAM

DRC ON DOWN SAMPLING

DOLBY DIGITAL BITSTREAM

ON OFF BITSTREAM

ENTERENTER

Select the desired setting.

SETUP

SETUP AUDIO

DRC DOWN SAMPLING DOLBY DIGITAL

ON ON BITSTREAM

SETUP DISPLAY

TV ASPECT STILL MODE

4:3 LETTER BOX AUTO

DVD Functions

–

Hint

• Record the password in case you forget it.

• If you forget the password, press [4], [7], [3], [7] at step 4, then enter your new password. Password will be cleared and parental levels will be set to “ALL”.

Parental Control limits the disc viewing that exceed your settings. (An incorrect password will not be acceptable.) This feature prevents your children from viewing inappropriate materials.

Parental Levels

Parental Level allows you to set the rating levels of your DVD discs. Playback will stop if the ratings exceed the levels you set. Follow steps 1 to 3 in the “CUSTOM Menu” section on page 20.

To Change the Password for Parental Controls

You can change your password for parental controls. Follow steps 1 to 3 in the “CUSTOM Menu” section on page 20.

ENTERENTER

Select “PARENTAL LEVEL”.

Enter your desired four-digit password.

PARENTAL menu

PASSWORD CHANGE

PARENTAL LEVEL ALL

SETUP

Select the desired level.

PARENTAL LEVEL ALL 8 [ADULT] 7 [NC-17] 6 [R]

To exit the menu

Select “PASSWORD CHANGE”.

PASSWORD CHANGE

PARENTAL LEVEL ALL

Enter your new four-digit password (except for 4737).

To exit the menu

Enter current four-digit password.

PARENTAL menu

You can change the other functions. Follow steps 1 to 3 in the “CUSTOM Menu” section on page 20.

OTHERS menu

ANGLE ICON:

(Default: ON)

Set to “ON” to show the angle icon when multiple camera angles are available during DVD playback.

AUTO POWER OFF:

(Default: ON)

Set to “ON” to turn this unit off automatically after 30 minutes of no use.

ANGLE ICON ON AUTO POWER OFF

ON OFF

ANGLE ICON ON AUTO POWER OFF

OFF ON

If you have set a password already, enter the current four-digit password.

SETUP

ENTERENTER

1 2 3

4 5 6

7 8 9

CONTROL LEVELS

• ALL: All parental locks are canceled.

• Level 8: DVD softwares of any grades (adult/general/children) can be played back.

• Levels 7 to 2:

Only DVD softwares intended for general use and children can be played back.

• Level 1: Only DVD softwares intended for children can be played back, with those intended for adult and general use prohibited.

TIPS FOR LEVELS

• 8 [ADULT]: DVD software of any grades (adult/general/children) can be played back.

• 7 [NC-17]: No one under 17 admitted

• 6 [R]: Restricted; under 17 requires accompanying parent or adult guardian

• 5 [PGR]: Parental Guidance Recommended

• 4 [PG13]: Unsuitable for children under 13

• 3 [PG]: Parental Guidance suggested

• 2 [G]: General Audience

• 1 [KID SAFE]: Suitable for children

Hint

•

DVD-Video discs may not respond to the parental lock settings. Make sure this function works with your DVD-Video discs.

1 2 3

4 5 6

7 8 9

PARENTAL Setting

OTHERS Setting

1 2 3

4 5 6

7 8 9

To exit the menu

Select the desired item.

or or

SETUP PARENTAL

PASSWORD

Enter current password.

SETUP PARENTAL

PASSWORD

Please enter a 4-digit password.

SETUP PARENTAL

PASSWORD

Enter current password.

SETUP PARENTAL

PASSWORD Please enter a 4-digit password.

SETUP OTHERS

ANGLE ICON AUTO POWER OFF

ON ON

Information

–

3 Select “YES”.2 Select “INITIALIZE”.

1 Press [SETUP] in the

stop mode.

Troubleshooting Guide

If this unit does not perform properly when operated as instructed in this Owner's Manual, check this unit consulting the following checklist.

•

Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Owner’s Manual for details on correct operations.

• Playback from a desired track and random playback are not available during program playback.

• Some functions are prohibited on some discs.

Information

DVD / VCR

PROBLEM CORRECTIVE ACTION

No power.

• Make sure the power plug is connected to an AC outlet.

• Make sure the power is turned on.

This unit does not respond to the remote control.

• Check if the power plug is connected to an AC outlet.

• Check the batteries in the remote control.

• Aim the remote control directly at the remote sensor. If necessary, remove all the obstacles between the sensor and the remote control.

• You have to be within 23 feet (7m) of this unit.

• Check if the right mode is selected. If it’s not in the right mode, press [DVD] or [VCR], whichever you need, on the remote control.

• Check if a cassette tape is in this unit.

• Tune your radio to an empty AM station so that you hear a lot of noises. Turn the volume up, then if you hear some signal sound from the radio in response to your pressing buttons on the remote control, the remote control is working.

• Press and hold any button on remote control toward a digital camera. The remote control is working if you conﬁ rm infrared light through the digital camera.

Poor picture or noise.

• Interference signal may be received. Change the position and orientation of the unit.

VCR

Timer recording is impossible.

• Make sure the Timer Recording is set correctly.

• Make sure indicator on the front panel lights up. If not, press [SUBTITLE/T-SET].

• Make sure the VCR clock is set correctly.

Cannot go into record mode.

• Make sure the tape has a record tab. If needed, cover the hole with adhesive tape.

• Activate this unit in VCR mode. Press [VCR] on the remote control so that the VCR OUTPUT light is lit.

Playback picture is partially noisy.

• Adjust tracking control for a better picture by pressing [CHANNEL L/K]] on the unit or [SKIP/CH. G/K, H/L] on the remote control.

Cannot view a tape but the audio is OK.

• Head cleaning may be necessary. Refer to “AUTO HEAD CLEANING”.

• Make sure the VCR is not in the Menu mode.

No or poor, playback picture.

• Change the RF output channel to CH4. Then select the same channel on the TV.

• Fine tune your TV.

TV programs cannot be seen normally.

• Re-check the ANT-IN and ANT-OUT connections. See the front page and page 6.

• Press [VCR].

• Press [VCR] on the remote control to activate it in the VCR mode. Check if the VCR OUTPUT light is lit, then set it to the TV position by pressing [VCR].

Video or color fades in and out when making a copy of a video tape.

• You cannot copy a copyrighted video tape. You are experiencing copy guard protection.

Cannot remove the tape.

• Check if this unit is in the VCR mode. If not, press [VCR] on the remote control to switch the mode.

DVD

No picture.

• Connect the video cable ﬁ rmly.

• Insert a correct video disc that plays on this unit.

• Press [DVD] on the remote control. Check if the DVD OUTPUT light is lit. Then try other DVD features.

Disc cannot be played.

• Insert the disc.

• Clean the disc.

• Place the disc correctly with the label side up.

• Cancel the parental lock or change the control levels.

• Handle a disc with special care so that it does not have ﬁ ngerprints, scratches, or dusts on its surface.

No sound.

• Connect the audio cable ﬁ rmly.

• Turn the power of the audio component on.

• Correct the audio output settings.

• Correct the input settings on the audio component.

Distorted picture.

• Connect this unit directly to the TV.

• There are some cases where pictures may be slightly distorted, and those are not a sign of a malfunction.

• Although pictures may stop for a moment, this is not a malfunction.

Audio or subtitle language does not match the setup.

• The selected language is not available for audio or subtitles on the DVD.

-This is not a malfunction.

The camera angle cannot be changed.

• The DVD does not contain sequences recorded from different camera angles.

-This is not a malfunction.

Audio or subtitle language cannot be changed.

• The DVD does not contain audio source or subtitles in the selected language.

-This is not a malfunction.

“Prohibited icon” appears on the screen, prohibiting an operation.

• That operation is prohibited by this unit or the disc.

-This is not a malfunction.

Hint

• When you cancel to initialize at step 3, select “NO”.

Reset to the Default Setting (Except for PARENTAL Setting)

SETUP

Press twice.

SETUP

PLAY

STOP

ENTERENTER

4 To exit the menu

oror

SETUP

QUICK CUSTOM INITIALIZE

SETUP INITIALIZE

Initialize? NO YES

SETUP

QUICK CUSTOM INITIALIZE

Information

–

Language Code List

Specifications

A-B

Abkhazian 4748 Afar 4747 Afrikaans 4752 Albanian 6563 Amharic 4759 Arabic 4764 Armenian 5471 Assamese 4765 Aymara 4771 Azerbaijani 4772 Bashkir 4847 Basque 5167 Bengali;Bangla 4860 Bhutani 5072 Bihari 4854 Bislama 4855 Breton 4864 Bulgarian 4853 Burmese 5971 Byelorussian 4851

C-E

Cambodian 5759 Catalan 4947 Chinese [CHI] 7254 Corsican 4961 Croatian 5464 Czech [CZE] 4965 Danish [DAN] 5047 Dutch [DUT] 6058 English [ENG] 5160 Esperanto 5161 Estonian 5166

F-H

Faroese 5261 Fiji 5256 Finnish [FIN] 5255

French [FRE] 5264 Frisian 5271 Galician 5358 Georgian 5747 German [GER] 5051 Greek [GRE] 5158 Greenlandic 5758 Guarani 5360 Gujarati 5367 Hausa 5447 Hebrew 5569 Hindi 5455 Hungarian [HUN] 5467

I-K

Icelandic [ICE] 5565 Indonesian 5560 Interlingua 5547 Interlingue 5551 Inupiak 5557 Irish [IRI] 5347 Italian [ITA] 5566 Japanese [JPN] 5647 Javanese 5669 Kannada 5760 Kashmiri 5765 Kazakh 5757 Kinyarwanda 6469 Kirghiz 5771 Kirundi 6460 Korean [KOR] 5761 Kurdish 5767

L-N

Laothian 5861 Latin 5847 Latvian;Lettish 5868 Lingala 5860 Lithuanian 5866

Macedonian 5957 Malagasy 5953 Malay 5965 Malayalam 5958 Maltese 5966 Maori 5955 Marathi 5964 Moldavian 5961 Mongolian 5960 Nauru 6047 Nepali 6051 Norwegian [NOR] 6061

O-R

Occitan 6149 Oriya 6164 Oromo(Afan) 6159 Panjabi 6247 Pashto;Pushto 6265 Persian 5247 Polish [POL] 6258 Portuguese [POR] 6266 Quechua 6367 Rhaeto-Romance 6459 Romanian [RUM] 6461 Russian [RUS] 6467

Samoan 6559 Sangho 6553 Sanskrit 6547 Scots Gaelic 5350 Serbian 6564 Serbo-Croatian 6554 Sesotho 6566 Setswana 6660 Shona 6560 Sindhi 6550 Singhalese 6555

Siswat 6565 Slovak 6557 Slovenian 6558 Somali 6561 Spanish [SPA] 5165 Sundanese 6567 Swahili 6569 Swedish [SWE] 6568

Tagalog 6658 Tajik 6653 Tamil 6647 Tatar 6666 Telugu 6651 Thai 6654 Tibetan 4861 Tigrinya 6655 Tonga 6661 Tsonga 6665 Turkish [TUR] 6664 Turkmen 6657 Twi 6669

U-Z

Ukrainian 6757 Urdu 6764 Uzbek 6772 Vietnamese 6855 Volapuk 6861 Welsh 4971 Wolof 6961 Xhosa 7054 Yiddish 5655 Yoruba 7161 Zulu 7267

Language Code Language Code Language Code Language Code

If you choose a Language that has a 3 letter language code, the code will be displayed every time you change the Audio or Subtitle language setting on page 19. If you choose any other languages, ‘---’ will be displayed instead. (3 letter language code is written in bracket.)

Video Heads :

Four Heads

Output signal format :

NTSC color

Power source :

120 V AC +/- 10%, 60 Hz +/- 0.5%

Power consumption :

21 W (standby: 3.8W)

Operating temperature :

41°F (5°C) to 104°F (40°C)

Dimensions :

W : 17 3/16” (435mm) H : 3 3/4” (94mm) D : 9 3/16” (233mm)

Weight :

Approx 6.0lbs (2.7kg)

• Designs and specifications are subject to change without notice.

• If there is a discrepancy between languages, the default language will be English.

–

MEMO

–

MEMO

–

MEMO

–

LIMITED WARRANTY

This form describes the protection You will have under this Limited Warranty.

LIMITED WARRANTY PERIOD:

This Limited Warranty begins on the date of purchase of the Covered Product and continues for a period of six months.

WHAT IS COVERED:

Meijer will pay the cost of labor and repair or replacement parts in the event Your Covered Product fails to operate as a result of a mechanical or electrical failure caused by defects in workmanship and/or materials. A mechanical or electrical failure caused by a direct result of a power surge is also covered. Parts will be replaced with those of like kind and quality, and may be new or remanufactured. If the Covered Product cannot be repaired, if the cost of the repair exceeds the original purchase price or if parts are not available due to the age of the Covered Product or discontinued by the manufacturer, the Covered Product will be replaced with a product of similar features.

WHERE YOU ARE COVERED:

Coverage under this Limited Warranty is limited to the United States of America, including the District of Columbia. It does not include any Canadian or U.S. Territories including Guam, Puerto Rico, or U.S. Virgin Islands.

WHAT IS NOT COVERED:

• PRODUCTS NOT ORIGINALLY COVERED BY A MANUFACTURER’S WARRANTY;

• ITEMS THAT ARE STILL COVERED BY THE MANUFACTURER’S WARRANTY, REGARDLESS OF WHETHER THE MANUFACTURER HONORS SUCH WARRANTY;

• PERIODIC CHECKUPS AND/OR PREVENTIVE MAINTENANCE AS DIRECTED BY THE MANUFACTURER EXCEPT AS PROVIDED HEREIN;

• INHERENT PRODUCT DEFECTS THAT ARE THE RESPONSIBILITY OF THE MANUFACTURER OR PARTS FAILURE DUE TO A MANUFACTURER’S RECALL;

• ANY AND ALL PRE-EXISTING CONDITIONS THAT OCCUR PRIOR TO THE EFFECTIVE DATE OF THIS LIMITED WARRANTY AND/OR ANY COSTS TO REPAIR ANY PRODUCT SOLD “AS-IS” INCLUDING BUT NOT LIMITED TO FLOOR MODELS, DEMONSTRATION MODELS, ETC;

• PARTS OR REPAIRS DUE TO NORMAL WEAR AND TEAR AND ITEMS NORMALLY DESIGNED TO BE PERIODICALLY REPLACED BY THE PURCHASER DURING THE COVERED PRODUCT’S LIFE, INCLUDING BUT NOT LIMITED TO BATTERIES, LIGHT BULBS, ETC.;

• DAMAGE FROM ACCIDENT, ABUSE, MISUSE, MISHANDLING, INTRODUCTION OF FOREIGN OBJECTS INTO THE COVERED PRODUCT, UNAUTHORIZED MODIFICATIONS OR ALTERATIONS TO A COVERED PRODUCT, FAILURE TO FOLLOW THE MANUFACTURER’S INSTRUCTIONS, AND EXTERNAL CAUSES INCLUDING THIRD PARTY ACTIONS, FIRE, THEFT, INSECTS, ANIMALS, EXPOSURE TO WEATHER CONDITIONS, WINDSTORM, SAND, DIRT, HAIL, EARTHQUAKE, FLOOD, WATER, ACTS OF GOD OR CONSEQUENTIAL LOSS OF ANY NATURE;

• LOSS OR DAMAGE CAUSED BY WAR, INVASION OR ACT OF FOREIGN ENEMY, HOSTILITIES, CIVIL WAR, REBELLION, RIOT, STRIKE, LABOR DISTURBANCE, LOCKOUT, OR CIVIL COMMOTION;

• INCIDENTAL, CONSEQUENTIAL OR SECONDARY DAMAGES OR DELAY IN RENDERING SERVICE UNDER THIS LIMITED WARRANTY, OR LOSS OF USE DURING THE PERIOD THAT THE COVERED PRODUCT IS AT AN AUTHORIZED SERVICE CENTER OR OTHERWISE AWAITING PARTS;

• ANY PRODUCT USED IN A COMMERCIAL SETTING OR RENTAL BASIS;

• FAILURES THAT OCCUR OUTSIDE OF THE 50 STATES OF THE UNITED STATES OF AMERICA, INCLUDING THE DISTRICT OF COLUMBIA;

• NONFUNCTIONAL OR AESTHETIC PARTS INCLUDING BUT NOT LIMITED TO PLASTIC PARTS, KNOBS, ROLLERS, BASKETS, SCRATCHES, PEELING AND DENTS;

• UNAUTHORIZED REPAIRS AND/OR PARTS;

• COST OF INSTALLATION, SET-UP, DIAGNOSTIC CHARGES, REMOVAL OR REINSTALLATION OF THE COVERED PRODUCT, EXCEPT AS PROVIDED HEREIN;

• ACCESSORIES USED IN CONJUNCTION WITH A COVERED PRODUCT;

• ANY LOSS OTHER THAN A COVERED BREAKDOWN OF THE COVERED PRODUCT;

• SERVICE WHERE NO PROBLEM CAN BE FOUND;

• BREAKDOWNS WHICH ARE NOT REPORTED WITHIN THE TERM OF THIS LIMITED WARRANTY;

• IMPROPER INSTALLATION OF COMPONENTS OR PERIPHERALS;

• CORRUPTION OF ANY RECORDING MEDIA, INCLUDING ANY PROGRAM, DATA OR SETUP INFORMATION RESIDENT ON ANY HARD DRIVES AND INTERNAL OR EXTERNAL REMOVABLE STORAGE DEVICES, AS A RESULT OF THE MALFUNCTIONING OR DAMAGE OF AN OPERATING PART, OR AS A RESULT OF ANY REPAIRS OR REPLACEMENT UNDER THIS LIMITED WARRANTY;

• DAMAGE TO CLOTHING;

• COLOR

FADING OF PICTURE FOR ANY TELEVISION;

• BURNED-IN PHOSPHOR (INCLUDING IMAGE GHOSTING), PIXEL BURNOUT NOT IN ACCORDANCE WITH THE MANUFACTURER’S SPECIFICATIONS.

WHAT TO DO WHEN YOUR PRODUCT FAILS TO OPERATE:

• Call the 24-hour customer service toll-free number at (866) 845-9436.

Many oversights, which are not covered under this Limited Warranty, can be due to simple circumstances such as the Covered Product not being switched on, being unplugged, or a fuse blown at the junction box. For a Covered Product that uses batteries as the primary power supply, or a remote control unit, please check that the batteries do not need replacing or recharging.

SERVICE DELIVERABLES:

There is no deductible required to obtain service for Your Covered Product.

OTHER PROVISIONS:

Limit of Liability:

The limit of liability under this Limited Warranty is the least of the cost of (1) the purchase price of the Covered Product excluding tax and delivery costs or (2) authorized repairs not to exceed the purchase price of the Covered Product or (3) replacement of the Covered Product with similar features or (4) reimbursement for authorized repairs or replacement. Upon replacement, there is no longer any obligation for the replaced product under this Limited Warranty.

Limitations of Implied Warranty:

All Implied Warranties which may arise under state law, including all Implied Warranties of Merchantability or Fitness for a particular purpose, are limited to the duration of this Warranty and do not cover incidental or consequential damages. Some states do not allow limitations on how long an Implied Warranty lasts or the exclusion of incidental or consequential damages, so the above limitations or exclusions may not apply to You. This Warranty gives You specific legal rights, and You may also have other rights which vary from state to state.

Transferability and Renewals:

This Limited Warranty is not transferable or renewable.

Subrogation:

If We pay for a loss, We may require You to assign Us Your rights of recovery against others. We will not pay for a loss if You impair these rights to recover. Your rights to recover from others may not be waived.

Arbitration:

In the event of a disagreement between You and Us concerning costs, either of us may make a written demand for arbitration. This must be done within sixty (60) days after the day You filed Your claim. Each of us will select an arbitrator. The two arbitrators will select an umpire. Each of us will pay the expenses of the arbitrator We select. The expenses of the umpire will be shared equally. Unless both of us agree otherwise, arbitration will take place in the county and state in which You live. Local rules apply. A majority decision will be binding.

Español

✄

–

Pulse [B] para AJUSTE AUTO.

•

Si no se ha ajustado el reloj, aparece la pantalla AJUSTE DE RELOJ cuando pulse [MENU]. En este caso, vaya al paso 2.

Seleccione el mes actual.

Seleccione el dia actual.

Seleccione el año actual.

Seleccione la hora actual.

Seleccione los minutos actuales.

Seleccione “AM” o “PM”.

Para salir de la pantalla AJUSTE DE RELOJ

1 Encienda el televisor y sintonice al canal 3.

• Si el canal 3 se está utilizando para una transmisión, vea la sección “Canal de salida RF”.

POWER

Español

Conexiones

Ajuste del reloj

Conmutación VCR/DVD

Instalación de las pilas del control remoto

Activación de la unidad por primera vez

CHANNEL

OPEN/CLOSE

VCR DVD DVD IN

SKIPH

STOP PLAY

GSKIP

REV FWD

OUTPUT

DVDVCR

Botón OUTPUT

Luz DVD OUTPUT

Luz VCR OUTPUT

Botón DVD

Botón VCR

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

REC/OTR

SETUP TOP MENU

MODE ZOOM

SUBTITLE

T-SET

ANGLE

ENTER

RETURN

MODE

REPEAT A-B

OPEN/CLOSE

/EJECT

SPEED AUDIO

CLEAR/

C. RESET

1 2 3

4 5 6

7 8 9

+10

MODO VCR

Pulse [VCR] en el control remoto. (Compruebe que está encendida la luz VCR OUTPUT.)

MODO DVD

Pulse [DVD] en el control remoto. (Compruebe que está encendida la luz DVD OUTPUT.)

No Espere unos minutos.

Después del escaneo

• El sintonizador se detiene en el canal memorizado más bajo.

• Puede seleccionar sólo los canales memorizados en esta unidad

con [SKIP/CH. G//K, H//L] (o [CHANNEL K // L]).

• Si aparece nuevamente “AJUSTE AUTO” en la pantalla de TV,

verifique las conexiones de cable. Presione nuevamente [B].

Si Pulse

[MENU]

para salir.

Conecta el cable de la caja de canales de cable o la caja de

satélite en la toma ANT-IN de la unidad?

- M E N U -

PROGRAMAR AUTOREPETIR [OFF] AJUSTE CANAL B AJUSTE DE RELOJ SELEC. IDIOMA

AJUSTE DE RELOJ

MES DIA AÑO 1 0 / – – – – – –

HORA MINUTO AM/PM – – : – – – –

AJUSTE DE RELOJ

MES DIA AÑO 1 0 / 0 2 – – – –

HORA MINUTO AM/PM – – : – – – –

AJUSTE DE RELOJ

MES DIA AÑO 1 0 / 0 2 2 0 0 6

HORA MINUTO AM/PM – – : – – – –

AJUSTE DE RELOJ

MES DIA AÑO 1 0 / 0 2 LUN 2 0 0 6

HORA MINUTO AM/PM 0 5 : – – – –

AJUSTE DE RELOJ

MES DIA AÑO 1 0 / 0 2 LUN 2 0 0 6

HORA MINUTO AM/PM 0 5 : 4 0 – –

AJUSTE DE RELOJ

MES DIA AÑO 1 0 / 0 2 LUN 2 0 0 6

HORA MINUTO AM/PM 0 5 : 4 0 P M AM BPM

Consulte la “Basic TV Connection” en la página delantera antes de utilizar esta unidad.

Canal de salida RF

Si el canal 3 se está utilizando para una transmisión,

1) Programe su televisor al canal 4.

2) Inserte una cinta pregrabada en esta unidad.

3) Pulse

[OUTPUT] en la unidad para que se encienda la

luz VCR OUTPUT.

• Si aparece ruido en la pantalla de TV, presione [VCR/TV]

en el mando a distancia.

4) Pulse una vez

[PLAY B].

5) Después de unos segundos, pulse [PLAY B] en la

unidad durante 3 segundos.

• El canal de salida RF cambiará del canal 3 al canal 4 y podrá ver una imagen reproducida.

• Cuando no aparezca una imagen en la pantalla del televisor, repita el paso 4.

6) Pulse [STOP C] para parar la reproducción.

Consejo

• Si pulsa sólo [OUTPUT] en el panel frontal NO cambía el modo del

control remoto. DEBE seleccionar también el modo correcto en el control remoto.

LANGUAGE SELECT

B ENGLISH [ON] FRANCAIS ESPAÑOL

CA 01

AJUSTE AUTO

VCR

Español

✄

–

Reproducción de la grabadora de vídeo

Reproducción de DVD/CD

Control remoto

Antes: Encienda el televisor y cambie al canal 3.

• Si el canal 3 se está utilizando para una transmisión, vea la sección “Canal de salida RF”.

PLAY

STOP

OPEN/CLOSE

/EJECT

Antes: Encienda el televisor, amplificador y otros equipos que puedan estar conectados a esta unidad. Asegúrese que el televisor y el sintoamplificador de audio (de venta en los comercios) están en el canal correcto.

Español

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

REC/OTR

SETUP TOP MENU

MODE ZOOM

SUBTITLE

T-SET

ANGLE

ENTER

RETURN

MODE

REPEAT A-B

OPEN/CLOSE

/EJECT

SPEED AUDIO

CLEAR/

C. RESET

1 2 3

4 5 6

7 8 9

+10

PLAY

STOP

POWER

OPEN/CLOSE

/EJECT

Ponga un disco con la etiqueta hacia arriba.

Para empezar la reproducción

Para parar la reproducción

Para expulsar

VCR

DVD

Modo DVD

Mode de grabadora de video

1 2 3

4 5 6

7 8 9

+10

• Para seleccionar directamente el capítulo o el título.

• Para seleccionar directamente la canción.

• Para seleccionar el canal.

• El botón +10 no tiene efecto en el modo de grabadora de vídeo.

• Para buscar en avance/ retroceso en un disco.

•

Para empezar la reproducción en avance/retroceso lento durante el modo de pausa.

• Para buscar en avance/retroceso en un disco.

• Para el avance/retroceso de una cinta.

A-B

• Para repetir entre los puntos A y B elegidos.

ANGLE

•

Para seleccionar los ángulos de la cámara en un disco.

AUDIO

• Para seleccionar el idioma de audio en un disco.

• Para seleccionar ESTÉREO, L-ch o R-ch.

CLEAR/

C. RESET

• Para borrar los marcadores.

• Para borrar los números entrados incorrectamente.

• Para borrar el punto para la repetición A-B.

• Para borrar los marcadores.

• Para retirar el Nº de estado en la entrada de programa.

• Para borrar los números entrados incorrectamente.

• Para borrar el punto para la repetición A-B.

• Para salir del menú de la grabadora de vídeo.

• Para reponer el contador de cinta.

DISPLAY

• Para indicar el modo de disco actual.

• Para indicar la hora actual, contador de cinta y canal.

DVD

• Para seleccionar el modo de salida de DVD.

• Para activar el mando a distancia en el modo DVD.

• Para seleccionar el modo de salida de DVD.

• Para activar el mando a distancia en el modo DVD.

ENTER

• Para mover el cursor y determinar su posición.

• Para seleccionar un ítem en el menú de la grabadora de vídeo.

• Para avanzar al siguiente menú de la grabadora de vídeo.

•

Para volver un paso durante el ajuste del reloj y temporizador.

• Para llamar el menu en un disco.

• Para llamar el menú de la grabadora de vídeo.

MODE

• Para activar/desactivar el nivel del negro.

• Para activar/desactivar el envolvente virtual.

• Para disponer el orden de reproducción o la reproducción aleatoria.

• Para activar/desactivar el envolvente virtual.

OPEN/CLOSE

/EJECT

• Para abrir o cerrar la bandeja del disco.

•

Para expulsar el videocasete de la grabadora de vídeo.

PAUSE

• Para hacer una pausa de reproducción del disco.

•

Para avanzar la reproducción un cuadro a la vez.

• Para hacer una pausa en la reproducción del disco.

•

Para hacer una pausa de la reproducción o grabación de la cinta.

•

Para avanzar la reproducción un cuadro a la vez.

PLAY

•

Para empezar la reproducción del disco.

• Para empezar la reproducción del disco.

•

Para empezar la reproducción de la cinta.

POWER

• Para encender o apagar la unidad.

REC/OTR

•

Para empezar una grabaciòn o una grabaciòn de un toque.

REPEAT

• Para reproducir repetidamente un capítulo o título.

• Para reproducir repetidamente una canción o disco.

RETURN

• Para volver a la operación previa en el menú.

MODE

• Para buscar un capítulo, título u hora.

• Para colocar o buscar los marcadores.

• Para buscar una canción.

• Para buscar la hora.

• Para colocar o buscar los marcadores.

• Para llamar el menú de búsqueda de índice u hora.

SETUP

• Para llamar el menú de programación de DVD.

SKIP/CH.

• Para saltar capítulos o titulo. • Para saltar canciones.

• Para cambiar de canal.

•

Para ajustar manualmente elseguimiento durante la reproducción.

SLOW

• Para ver la cinta en cámara lenta.

SPEED

• Para seleccionar la velocidad de grabación.

STOP

• Para parar la reproducción. • Para parar la reproducción.

• Para parar la reproducción o grabación.

SUBTITLE

T-SET

• Para seleccionar subtítulos en un disco.

• Para poner la grabadora de vídeo en el modo de espera para una grabación con temporizador.

TOP MENU

• Para llamar el menú superior en un disco.

VCR

•

Para seleccionar el modo de salida de la grabadora de vídeo.

•

Para activar el mando a distancia en el modo de la grabadora de vídeo.

VCR/TV

•

Para seleccionar la posición de DVD o posición del elevisor.

• Para seleccionar la posición de CD o la posición del televisor.

• Para seleccionar la posición de la grabadora de vídeo o posición del televisor.

ZOOM

• Para ampliar parte de la imagen. (x2/x4)

Botón (Orden alfavético)

Disco/cinta

✄

–

Turn on the TV and set it to channel 3.

•

If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section.

Select your language in the first time you turn on this unit. Then press [B] to go to next step.

POWER

Quick Use Guide

Please refer to “Basic TV Connection” on the front page before you use this unit.

RF Output Channel

If channel 3 has been already occupied for broadcasting,

1) Set your TV to channel 4.

2) Insert a pre-recorded tape into this unit.

3) Press

[OUTPUT] on the unit so that the VCR OUTPUT

light is lit.

•

If noise appears on the TV screen, press [VCR/TV] on the remote control.

4) Press [PLAY B] once.

5) After a few seconds, press and hold [PLAY B] on the

unit for 3 seconds.

• The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

• When a picture does not appear on the TV screen, repeat step 4.

6) Press [STOP C] to stop playback.

Connections

Clock Set Up

Turn on the Unit for the First Time

VCR/DVD Switching

Installing the Batteries for the Remote Control

CHANNEL

OPEN/CLOSE

VCR DVD DVD IN

SKIP H

STOP PLAY

G SKIP

REV FWD

OUTPUT

DVDVCR

OUTPUT button

DVD OUTPUT light

VCR OUTPUT light

DVD button

VCR button

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

REC/OTR

SETUP TOP MENU

MODE ZOOM

SUBTITLE

T-SET

ANGLE

ENTER

RETURN

MODE

REPEAT A-B

OPEN/CLOSE

/EJECT

SPEED AUDIO

CLEAR/ C. RESET

1 2 3

4 5 6

7 8 9

+10

VCR MODE

Press [VCR] on the remote control. (Verify that the VCR OUTPUT light is lit.)

DVD MODE

Press [DVD] on the remote control. (Verify that the DVD OUTPUT light is lit.)

No Please wait for a few minutes.

After scanning...

• The tuner stops on the lowest memorized channel.

• You can select only the channels memorized in this unit by using

[SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).

• If “AUTO SET UP” appears on the TV screen again, check the

cable connections. Then, press [B] once again.

Yes Press [MENU] to exit.

Do you connect the cable from the cable box or the satellite box to the unit’s ANT-IN jack?

Hint

• Pressing only [OUTPUT] on the front panel DOES NOT switch the

mode of the remote control. You MUST select the correct mode on the remote control.

Press [MENU] and select “CLOCK SET“. Then press [B] to go to next step.

Select the current month. Then press [B] to go to next step.

Select the current day. Then press [B] to go to next step.

Select the current year. Then press [B] to go to next step.

Select the current hour. Then press [B] to go to next step.

Select the current minute. Then press [B] to go to next step.

Select “AM” or “PM”.

To exit the CLOCK SET screen

• If the clock is not set, the CLOCK SET screen appears when

you press [MENU]. In this case, go to step 2.

- M E N U -

TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP B CLOCK SET LANGUAGE SELECT

CLOCK SET

MONTH DAY YEAR 1 0 / – – – – – –

HOUR MINUTE AM/PM – – : – – – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 – – – –

HOUR MINUTE AM/PM – – : – – – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 2 0 0 6

HOUR MINUTE AM/PM – – : – – – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM 0 5 : – – – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM 0 5 : 4 0 – –

CLOCK SET

MONTH DAY YEAR 1 0 / 0 2 MON 2 0 0 6

HOUR MINUTE AM/PM 0 5 : 4 0 P M AM B PM

LANGUAGE SELECT

B ENGLISH [ON] FRANCAIS ESPAÑOL

Press [B] to start Auto Set Up.

CH 01

AUTO SET UP

YES

VCR VCR

✄

1VMN22699 / E8A03UD★★★★★

Printed in China

VCR Playback

DVD/CD Playback

Remote Control

Before: Turn on the TV and set it to channel 3.

• If channel 3 has been already occupied for broadcasting, see “RF Output Channel” section.

PLAY

STOP

OPEN/CLOSE

/EJECT

Before: Turn on the TV, amplifier and any other components which are connected to this unit. Make sure the TV and audio receiver (commercially available) are set to the correct channel.

Quick Use Guide

POWER

DISPLAY VCR DVD PAUSE

SLOW

VCR/TV

SKIP/CH.

PLAY

STOP

REC/OTR

SETUP TOP MENU

MODE ZOOM

SUBTITLE

T-SET

ANGLE

ENTER

RETURN

MODE

REPEAT A-B

OPEN/CLOSE

/EJECT

SPEED AUDIO

CLEAR/ C. RESET

1 2 3

4 5 6

7 8 9

+10

1 2

PLAY

STOP

POWER

OPEN/CLOSE

/EJECT

Insert a disc with label facing up.

To start playback

To stop playback

To eject the cassette

VCR

DVD

Insert a video cassette into this unit.

DVD mode VCR mode

1 2 3

4 5 6

7 8 9

+10

• To select chapter or title directly.

• To select track directly.

• To select channel.

• The +10 button has no effect in VCR mode.

•

To search forward/backward through a disc.

•

To begin slow forward/reverse playback in the pause mode.

• To search forward/backward through a disc.

• To forward/backward a tape.

A-B

• To repeat between your chosen point A and B.

ANGLE

• To select camera angles on a disc.

AUDIO

• To select audio languages on a disc.

• To select STEREO, L-ch or R-ch.

CLEAR/

C. RESET

• To clear the markers.

• To clear the numbers entered incorrectly.

• To cancel the point for A-B repeat.

• To clear the markers.

• To remove status number in program input.

• To clear the numbers entered incorrectly.

• To cancel the point for A-B repeat.

• To exit the VCR Menu.

• To reset the tape counter.

DISPLAY

• To display the current disc mode.

• To display the current time, tape counter, and channel.

DVD

• To select the DVD output mode.

• To activate the remote control in DVD mode.

• To select the DVD output mode.

• To activate the remote control in DVD mode.

ENTER

• To move the cursor and determine its position.

• To select an item on the VCR Menu.

• To advance to the next VCR Menu.

• To go back one step during clock and timer setting.

• To call up the Menu on a disc.

• To call up the VCR Menu.

MODE

• To set black level on/off.

• To set virtual surround on/off.

• To arrange the playing order or play randomly.

• To set virtual surround on/off.

OPEN/CLOSE

/EJECT

• To open or close the disc tray.

• To eject the video cassette from the VCR.

PAUSE

• To pause disc playback.

• To advance playback one frame at a time.

• To pause disc playback.

• To pause tape playback or recording.

• To advance playback one frame at a time.

PLAY

• To begin disc playback. • To begin disc playback. • To begin tape playback.

POWER

• To turn the unit on/off. • To turn the unit on/off. • To turn the unit on/off.

REC/OTR

• To start a recording or One Touch Recording.

REPEAT

• To play a chapter or title repeatedly.

• To play a track or disc repeatedly.

RETURN

• To return to the previous operation in menu.

MODE

• To search chapter, title or time.

•

To set or search the markers.

• To search track.

• To search time.

• To set or search the markers.

• To call up the index or time search menu.

SETUP

• To call up the DVD setup menu.

SKIP/CH.

• To skip chapters or titles. • To skip tracks.

• To change channels.

• To adjust the tracking manually during playback.

SLOW

• To view the tape in slow motion.

SPEED

• To select the recording speed.

STOP

• To stop playback. • To stop playback.

• To stop playback or recording.

SUBTITLE

T-SET

• To select subtitles on a disc.

•

To put the VCR into standby mode for a Timer Recording.

TOP MENU

• To call up the Top Menu on a disc.

VCR

•

To select the VCR output mode.

• To activate the remote control in VCR mode.

VCR/TV

• To select DVD position or TV position.

• To select CD position or TV position.

• To select VCR position or TV position.

ZOOM

• To magnify part of a picture. (x2/x4)

Button (Alphabetical order)

Disc/Tape

Funai MJ840G User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual