Fujitsu TX150 S4 User Manual

PRIMERGY TX150 S4

System configurator and order-information guide

December 2005

Contents

Instructions
Configuration diagram
Configurator

0 System software
I Basic unit
II Processor
III Memory
IV Graphics
V Accessible drives
VI Hard disk drives
VII SCSI Controller
VIII Disk array
IX Communication/Network
X System management options
XI Miscellaneous
XII Country specific options

Change report

PRIMERGY Server

System configurator and order-information guide

PRIMERGY TX150 S4 Status 25.11.2005

Instructions

This document contains basic product and configuration information that will enable you to configure your system via

PC-/ System-Architect.

Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete

PRIMERGY Rack system.

You can configure your individual PRIMERGY server in order to adjust your specific requirements.

The System configurator is divided into several chapters that are identical to the current price list and PC-/ System-Architect

Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through

the configurator by following the lines from the top to the bottom.

Section

In one chapter you can only select as many components (here 4x) as the arrow indicates.

Please note that there are information symbols which indicate necessary information.

Further information in the internet see:

http://www.primergy.com

(internet)

http://extranet.fujitsu-siemens.com/primergy

(extranet)

Prices and availability see price list and PC-/ System-Architect

Subject to change and errors excepted

X times

III

S26361-XXX-XXX S26361-XXX-XXX

Memory XXX MB Memory XXX MB

max. X times per system max. X times per system

Memory, example

There are X memory slots which can be equipped with XXX MB.
It is permissible to make up to X passes through the memory upgrade options.

4x

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

2 of 18

System configurator and order-information guide

PRIMERGY TX150 S4 Status 25.11.2005

Configuration diagram PRIMERGY TX150 S4

3 x 5.25"

Modul 3

Accessible drives ( V )

Modul 4

Memory ( III )

PCIe x 1

PCIe x 4 (x8 Slot)

(Slot for Zero-Channel Controller)

Key:

System unit ( I )

SIDE VIEW FRONT VIEW

Standard Power Supply

or PS (I) 5.25" x 1.6"

1. PSU 2. PSU

Redundant power supply option 5.25" x 1.6"

5.25" x 1.6" CD / DVD drive

Modul 1

Pentium 4

Bank 1Bank 2

Modul 2

Processor ( II )

Extension slots

SCSI Controller ( VII )

1 PCI-Bus

Disk array ( VIII ) Hard disk drives ( VI )
Communication/Network ( IX )

6.

PCI short (5V) 32-Bit / 33MHz

5.

PCI short (5V) 32-Bit / 33MHz

4.2.1. 7.

PCI-X 66 long (3,3V)

3.

PCI-X 66 long (3,3V)

PCI long (5V) 32-Bit / 33MHz

SCSI 1"

SCSI 1"

SCSI 1"

SCSI 1"

Included in basic unit
Option

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

3 of 18

System configurator and order-information guide

Start PRIMERGY TX150 S4

PRIMERGY TX150 S4 Status 25.11.2005

http://extranet.fujitsu-siemens.com/primecluster

http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm

for internal users:

http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm

for partners:

http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm

SW Configurator IA32

with OEM-Software without OEM-Software

for PRIMERGY Server for PRIMERGY Server

VMware-Software software is not allowed,

- VCMS VirtualCenter Management Server apart from few VMware

- GSX Server and GSX Virtual Infrastructure Node add-ons

- P2V Assistant Enterprise Edition

For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.

Microsoft - Software: **) OES/NetWare-Software ***) PRIMECLUSTER *)

- Small Business Server 2003 - NetWare - Clustering

- Windows Server 2003, - Load Balancing
Web Edition (only English)

Standard Edition
Enterprise Edition

- Additional loose Linux - Software: **)
Client-Access-Licenses (CALs) - SUSE Linux Enterprise Server
(not for Web Edition) - SUSE Professional Linux

- Red Hat Enterprise Linux

SCO - Software: **)

- SCO OpenServer

- SCO UnixWare

CITRIX-Software für
Windows: W-MF

- Presentation Server
LoadBalancing
Additional User Licences

Later use of OEM operating system

Manageability Software: V**) Details eg. version numbers are published

- RemoteView Software in the separate SW-Configurator

- RemoteView Service Board

- RemoteDeploy

- Terminal Server Deploy

- vPMS 2005std

- Altiris Server Deployment

Backup-Software /
Application-Software: U

- ARCserve

- openSM2

Various Software Configurators and release lists (OS-Matrix / System Management / Security) can be optain under the following adresses:

Continue with PRIMERGY
HW configurator

*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under

**) Pay attention to the release and ordering information in PRINCE -> Operating System

***) Supply over distribution or procurement from FSC VP BC Software

Enterprise Products - PRIMERGY Server

Fujitsu Siemens Computers

4 of 18

System configurator and order-information guide

Start PRIMERGY TX150 S4

PRIMERGY TX150 S4 Status 25.11.2005

- SuSE Linux Enterprise Server

http://www.primecluster.com

for internal users:

http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm

for partners:

http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm

SW Configurator EM64T

with OEM-Software without OEM-Software

for PRIMERGY Server for PRIMERGY Server

Later use of OEM operating system
software is not allowed,
apart from few VMware
add-ons

For all SW products please refer to the corresponding software configurator accessible via
the Extranet under Configuration & Tools, -All configurations, -Software, URL see below.

only - Windows Server 2003, only
EM64T x64 Standard Edition EM64T - Red Hat Enterprise Linux

Microsoft - Software: W Linux - Software: L *) **)

x64 Enterprise Edition

- Additional loose
Client-Access-Lizenzen (CALs)

Details eg. version numbers are published
in the separate SW-Configurator

Manageability Software: V**)

- RemoteView Software

- RemoteView Service Board *) Pay attention to release information on datasheet under

- RemoteView Diagnosis

**) Pay attention to release and order information in PRINCE -> Operating System

http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm

***) Supply over distribution or procurement from FSC VP BC Software

Various Software Configurators and release lists (OS-Matrix / System Management / Security) can be optain under the following adresses:

Continue with PRIMERGY
HW configurator

Enterprise Products - PRIMERGY Server

Fujitsu Siemens Computers

5 of 18

System configurator and order-information guide

Start PRIMERGY TX150 S4

PRIMERGY TX150 S4 Status 25.11.2005

Cables included in basic unit

Connections

Cable

PRIMERGY TX150 S4

1.

IDE CD/DVD

¡¡¡

Key:¥68pins

2.

Backplane for 1x4

¥

68 or 50pins

SCSI hard disks

¥¥¥¥¡

IDE

incl. terminator

terminator

Section

I

Basic unit

System unit consisting of:
* Housing including standard power supply (no redundancy)
* Sliding screen with lock (only for floorstand version)

Systemboard with:
* 7 PCI slots:

1x PCIe x 1
1x PCIe x 4 (x8 Slot)
1x PCI-X 66 long (3,3V)
1x PCI-X 66 (3,3V) ZCR Slot

1x long / 2x short 32Bit / 33MHz (5V)
* 4 memory slots for up to 8GB (PC4200) registered DDR II RAM (ECC), max. 2GB modul per slot
* 1 drive bay 3.5" occupied by 1 floppy disk 1.44MB 1" height (optional)
* 3 Einbauplätze 5,25" für bedienbare Laufwerke
* 4 bays 1" for hot plug SCSI HD)
* ATI Range XL Graphic controller 8MB
* Intel Broadcom (5721) 10/100/1000 Mb/s on-board
* 1 x Fast-IDE (ATA) Controller on-board (for 1x 2 devices)
* 1-channel Ultra 320 SCSI Controller LSI 1020A on-board

with HW RAID IME (IME = Integrated Mirroring Enhanced)

Options:
* Hot plug PS or a second redundant hot plug PS version can be configured by ordering the
appropriate upgrade option
* LSI Zero Channel RAID option, simultaneous use of HD and Tape Drive possible

Cables:

1. IDE cable for CD/DVD

2. With SCSI variant wide LVD SCSI cable for connection of the HD backplane and two
accessible drives

PS/2 mouse (only for floorstand version)

ServerStart packet incl. ServerBooks CD, ServerSupport CD and ServerView
External Interfaces:

2x RS-232-C (serial, 9 pins)
1x Centronics (parallel, 25 pins, EPP/ECP compatible)
1x keyboard (PS/2)
1x mouse (PS/2)
1x VGA (15 pins)
1x USB 2.0 on front and 2x USB 2.0 on rearside
1x LAN RJ45

A

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

6 of 18

System configurator and order-information guide

A

PRIMERGY TX150 S4 Status 25.11.2005

Floorstand version SCSI basic unit 19" Rack version SCSI basic unit (5 U)

Pentium 4 processor, memory Pentium 4 processor, memory

PD 820 2.8GHz/800MHz/2x1MB 512MB S26361-K999-V136 PD 820 2.8GHz/800MHz/2x1MB 512MB S26361-K999-V336
PD 820 2.8GHz/800MHz/2x1MB 1GB S26361-K999-V146 PD 820 2.8GHz/800MHz/2x1MB 1GB S26361-K999-V346
PD 820 2.8GHz/800MHz/2x1MB 2GB S26361-K999-V156 PD 820 2.8GHz/800MHz/2x1MB 2GB S26361-K999-V356

S26113-F483-E1 floorstand S26113-F483-E1

hot plug power supply upgrade option versions hot plug power supply upgrade option
With this option the basic units contains A second, redundant With this option the basic units contains
1 hot plug power supply, 1 power power supply requires 1 hot plug power supply, 1 power
backplane and 1 dummy cover an additional power backplane and 1 dummy cover
replacing the standard power supply cord replacing the standard power supply
(no redundancy !) (section XII) (no redundancy !)
max. 1x per system max. 1x per system

S26113-F483-E11 S26113-F483-E11

2nd power supply module (PSU) 2nd power supply module (PSU)
for redundancy for redundancy
occupies one bay for occupies one bay for
hot plug power supply hot plug power supply
max. 1x per system max. 1x per system

B1 B2

For later conversion of basic units with standard power supply
to hot plug power supply, the following kit is available:

1.) hot plug PS upgrade kit, incl. 2 PS module: S26113-F483-L1
Conversion standard into hot plug PS

2.) Supplementary power supply module S26113-F483-L11
for redundancy or repair

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

7 of 18

System configurator and order-information guide

B1 B2

PRIMERGY TX150 S4 Status 25.11.2005

PRIMERGY Floorstand PRIMERGY Rack

PRIMECENTER- Rack

SNP:SY-F1647E301-P "rack-mounting ex factory"
Installation ex works for one This service is to be ordered once
server or subsystem per installable server/storage
Hereby the rack will be delivered subsystem, in order to get the
completely pre-mounted and server/storage subsystem
all wired connections are tested mounted into the PRIMERGY racks.

With racks 12U, 24U, 38U: In case of the 46 U PRIMERGY rack,
Systems and components this service has to be ordered,
will be delivered installed in the rack to get the mounting kits and the
With racks 46U: cables installed.
Systems and components
will be delivered separately
To be ordered only together with
a PRIMERGY­PRIMECENTER rack
e.g.:SNP:SY-K614V10x-P
S26361-K826-V10x

refer configurator PC-rack

max. 1x per System

For later conversion of TX150 base unit floorstand into base unit rack the following kit is availible

1.) Conversion TX150S4 base unit floorstand into base unit rack S26361-F2618-L240
rack mount kit has to be ordered separately

For (later) mounting in racks the following kits are available:

1.) PRIMERGY Classic-rack 42/23U adapter kit: S26361-F1331-L300
incl. cable carrier

2.) PRIMERGY DC- / PC- rack mounting kit: S26361-F2734-L32
incl. DC- PC- bracket, cable managment

3.) PRIMERGY mounting kit for server racks S26361-F2734-L32
conforming to EIA standards EIA-310-D for 19" racks.

C

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

8 of 18

System configurator and order-information guide

C

PRIMERGY TX150 S4 Status 25.11.2005

Section

Section

Section

II

III

S26361-F3000-E513 S26361-F3000-E514 S26361-F3000-E515

Main memory 512MB Main memory 1GB Main memory 2GB

3x

DDR2 533/PC2-4200 ub ECC DDR2 533/PC2-4200 ub ECC DDR2 533/PC2-4200 ub ECC
consisting of one module consisting of one module consisting of one module
occupies one bank occupies one bank occupies one bank
max. 3x per system max. 3x per system max. 3x per system

IV

Processor

Memory

There are 2 memory banks with 2 DIMM slots each.

Single channel memory configuration allow maximum flexibility:

Additional memory can be configured as single memory modules.

Dual channel memory configurations for maximum performance:

For optimum performance memory has to be configured in pairs of memory modules with identical size.

Graphics

ATI Rage XL (8MB)

D

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

9 of 18

System configurator and order-information guide

D

PRIMERGY TX150 S4 Status 25.11.2005

Section

SNP:SY-F2234E1-A S26361-F3148-E1

DVD-ROM ATAPI DVD-RW 16x super multi drive

2x

incl. description (Ger/US) only W2K, W3K and Linux

1.6 x 5.25", anthracite bezel 1.6 x 5.25", anthracite bezel
max. 2x per system max. 1x per system

V

S26361-F2575-E1

Floppy disk drive 1"
Connector: 26pin
incl. description (Ger/US)
1" * 3.5", anthracite bezel
max. 1x per system

Accessible drives

all formats, DUAL/DL, DVD-RAM

There are 3x 5.25" bays for accessible drives:

- 1x 5.25" bay is occupied by a DVD-/CD- respectively a CD-RW drive

- 2 x 5.25" bays remaining, can be occupied by 2x accessible drives

Setup TX150 S4 by ServerStart is supported with following configurations:

no DVD, no CD:

remote installation only ( PXE service & DHCP server required)

built in CD/DVD:

UNC Network share reachable or USB Floppy or MemoryBird connected

One of the following USB devices must be used for integrating the drivers during installation
process if no automized (e.g. Serverstart / Altiris / RIS / ADS / …) installation is done:

1) FDD USB (external): external USB FDD (USB cable included)

2) USB Memorybird: Memorybird 256 MB S26391-F6046-L256
Memorybird 1GB

S26391-F264-L226

S26391-F6046-L24

S26361-F3157-E3

Tape drive LTO2HH Ultrium
200GB, 24MB/s, U160 SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning cartridge

1.6 * 5.25", anthracite bezel
max. 1x per system

S26361-F2849-E3

Tape drive VXA-2
80GB, 6MB/s, U2W SCSI
Connector: HD68

2x

without cable
incl. description (Ger/US)
data and cleaning catridge

1.6 x 5.25", anthracite bezel
max. 2x per system

S26361-F2848-E3

Tape drive DDS Gen5
S26361-F2848-E31 (only for OBDR)
DDS-G5 for One buttom dis. recov.
36GB, 3MB/s, U2W SCSI
Connector: HD68
without cable
incl. description (Ger/US)
data and cleaning catridge

1.6 x 5.25", anthracite bezel
max. 2x per system

E

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

10 of 18

System configurator and order-information guide

E

PRIMERGY TX150 S4 Status 25.11.2005

S26361-F2814-E6 Backup drive and hard disk should run on separate channels
68-Pin Kit for accessible drives
Cable with Terminator
To connect acc. drives to
separate SCSI controller
max. 1x per system

If internal HDD's are connected at the RAID controller
(not IME/ZCR), then for internal accessible drives
the cable S26361-F2814-E6 must be ordered additionally!

Section

VI

S26361-F3121-E173 S26361-F3121-E114 S26361-F3121-E130

Hard disk 73GB in 1" carrier Hard disk 146GB in 1" carrier Hard disk 300GB in 1" carrier
10000rpm,<5,5ms, 8MB Cache 10000rpm,<5,5ms, 8MB Cache 10000rpm,<5,5ms, 8MB Cache

Ultra 320 SCSI (320MB/s) Ultra 320 SCSI (320MB/s) Ultra 320 SCSI (320MB/s)

Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins)
hot plug/hot replace tray hot plug/hot replace tray hot plug/hot replace tray
occupies 1" bay occupies 1" bay occupies 1" bay
SCSI/RAID controller necessary SCSI/RAID controller necessary SCSI/RAID controller necessary

Hard Disk Drives

4x max. 4x per system max. 4x per system max. 4x per system

S26361-F3121-E573 S26361-F3121-E514

Hard disk 73GB in 1" carrier Hard disk 146GB in 1" carrier

15.000rpm,<4ms, 8MB Cache 15.000rpm,<4ms, 8MB Cache

Ultra 320 SCSI (320MB/s) Ultra 320 SCSI (320MB/s)

Interface: Wide SCA (80-pins) Interface: Wide SCA (80-pins)
hot plug/hot replace tray hot plug/hot replace tray
occupies 1" bay occupies 1" bay
SCSI/ RAID controller necessary SCSI/ RAID controller necessary
max. 4x per system max. 4x per system

F

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

11 of 18

System configurator and order-information guide

F

PRIMERGY TX150 S4 Status 25.11.2005

LSI Integrated Mirroring Enhanced (IME) is a RAID 1 implementation (no RAID 0 support). It can be operated also with an odd

Section

VII

SCSI-Controller

All internal cables and adapters are included within the basic units and components respectively

Cabeling priorities:

internal HDs are cabled according to following priorities.
(Prio 1 - 3 ):

1.) For a configuration without any Disk Array Controller and without zero channel RAID

the onboard U320 Controller is connected to the internal HDs.

2.) For a configuration with a 2-channel Disk Array controller (without zero-channel RAID)

One channel will be connected with the internal hard disks.
The second channel is externally available.

internal backup devices are cabled according to following priorities.
(Prio 1 - 2 ):

1) For a configuration without additional SCSI controller

the onboard U320 controller is connected to internal backup devices

2) For a configuration with Adaptec SCSI Card 29160 S26361-F2399-E2
(without SCSI 160 controller S26361-F2644-E11)

this controller is connected to internal backup devices

A. on-board SCSI-controller for accessible drives and SCSI-HDs

1-channel Ultra 320 SCSI on-board controller; included as standard.

Example for IME with 3 data devices:

number of hard disks (max. one RAID 1 Set). There are, depending on system, up to 6 hard disks, including a hot spare disk,
possible. Supportet are only the operating systems Windows2000/2003 as well as SuSE and RedHat Linux.

All internal cables and adapters for the basic unit and for components are included.

1x per TX150S4

T26139-Y3849-L1

External on-board SCSI Interface connection of the on-board SCSI controller
Cable and external and the 29160.
connector interface (HD68) Cable sold separately not mounted in factory.
occupies one connection panel Use this cable only if on-board controller is not
max. 1x per system for ext. used otherwise (eg. S26361-F2814-E6)

G

Only SX10 Backup is released for the external

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

12 of 18

System configurator and order-information guide

G

PRIMERGY TX150 S4 Status 25.11.2005

B. SCSI controller for internal backup drives

S26361-F2399-E2

SCSI 160 Controller
Adaptec SCSI Card 29160
1 channel: LVD + Fast/ Ultra (decoupl.)
LVD connect. for HD, without cable
Fast/Ultra connect. for acc. drives
64/66 PCI, min 180 mm
int: Fast 50-pin or Ultra HD68
+ LVD HD68; ext: HD68(LVD)
SW:
max. 1x per system

S26361-F2814-E6

68-Pin Kit for accessible drives
Cable with Terminator
To connect acc. drives to
separate SCSI controller
max. 1x per system

C. SCSI controller for external drives and peripheral devices

Section

max. 4x

S26361-F2399-E1

SCSI U160 controller
Adaptec SCSI Card 29160
1 channel: LVD + Fast/ Ultra (decoupl.)
LVD connect. for HD, without cable
Fast/Ultra connect. for acc. drives
64/66 PCI, min 180 mm
int: Fast 50 pol oder Ultra HD68
+ LVD HD68; ext: HD68(LVD)
SW:
max. 1x per system

VIII

D. LSI - Controller

1-channel Ultra 320 SCSI on-board controller with LSI Integrated Mirroring (IME)
Standard SCSI-cabling of a PRIMERGY TX150 S4 basic unit with on-board controller

Ultra 320 SCSI controller is connected to the internal hard disks and internal backup devices,
if no additional HD/backup device controllers are configured.
1x per PRIMERGY TX150 S4

S26361-F3085-E128

0-channel RAID controller
LSI
320-0x
128MB SDRAM ECC Cache
BBU optional
in combination with on-board
U320 SCSI controller blue marked bay.
without cable
64Bit/133MHz PCI-X controller

3.3V power supply & signaling the IME function is no longer
max. 1x per system

Disk Array

D. zero-channel RAID controller (320-0x) for internal Disk Array
and additional RAID controllers for internal / external Disk Array

Zero channel RAID controller
LSI must be installed in the

With zero channel RAID controller

available.

Only SX10 Backup is for external
connection at the SCSI controller.

S26361-F3085-E10

Cache Battery Backup Unit

to be
continued
on next page

max. 1x pro Controller

H

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

13 of 18

System configurator and order-information guide

H

PRIMERGY TX150 S4 Status 25.11.2005

continued
on previous E. 2-Kanal Ultra 320 SCSI Controller für Disk Array

page

1x

S26361-F3090-E256

2-channel RAID Controller U320
LSI
320-2x
256MB SDRAM ECC Cache
default with TBBU
plug: internal 2x HD68;
external: 2x VHDCI
without cable
64/133 PCI-X controller, 180mm

3.3V and 5V tolerant signaling
max. 1x per system

The fitting connection cables can be found in the configurator
of the external storage system and / or rack.

S26361-F2814-E6 Backup drive and HDD should run on separate channels.
68-Pin Kit for accessible drives
Cable with Terminator
To connect acc. drives to
separate SCSI controller
max. 1x per system

If internal HDD's are connected at the RAID controller
(not IME/ZCR), then for internal accessible drives
the cable S26361-F2814-E6 must be ordered additionally!

I

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

14 of 18

System configurator and order-information guide

I

PRIMERGY TX150 S4 Status 25.11.2005

4x

Section

IX

Gigabit Ethernet Contr. on-board The Intel LAN controllers 1000MT can be used
Broadcom with the on-board controller in Teaming Mode
ext: for RJ 45-connector
SW: AFT, VLAN, Fast Channel

S26361-F3053-E1 S26361-F3142-E1

Gigabit Ethernet Contr. 1000TX Gigabit Ethernet Contr. 1000TX
Eth. Ctrl 1x1Gbit PCI-X Pro/1000MT Cu Eth. Ctrl 1x1Gbit PCI32 PRO/1000GT Cu
Intel PRO/1000 MT Server Adapter Intel Pro/1000 GT Adapter
Adapter Teaming Support
PCI-X (PCI64/133), min 165 mm ext: for RJ45-plug, Cat 5
ext: for RJ45-plug, Cat 5
connection with Cat 5 cabling SW: VLAN, Fast & Gbit Etherchannel
SW: VLAN, Fast & Gbit Etherchannel
max. 4x per system

S26361-F3011-E1

Gigabit Ethernet Contr dual 1000TX
Intel Pro/1000MT dual Server Adapter
Adapter Teaming Support
PCI-X (PCI64/133), min 163 mm
ext: for RJ45-plug, Cat 5
connection with Cat 5 cabling
SW: VLAN, Fast Etherchannel
max. 2x per system

Communication / Network

PCI 32 (33/66MHz),

connection with Cat 5 cabling

max. 4x per system

S26361-F1809-E2

ISDN SO Controller PCI
Eicon Diva Server BRI-2M 2.0
Incl. SO-connector
occu. short PCI slot min. 170 mm
SO-Interface
max. 2x per system

J

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

15 of 18

System configurator and order-information guide

J

PRIMERGY TX150 S4 Status 25.11.2005

Section

Section

X

S26361-F2425-E103
RSB S2 LP 3HU

RemoteView Service Board S2
Low Profile Version with 3 U bracket
for one standard PCI-slot
incl. cables and RV SW
max. 1x per system

S26361-F2425-E305
RSB S2 LP external power supply

RemoteView Service Board S2
low profile external power supply
including power cable
with Euro- and Euro socket connector

XI

System management options

Miscellaneous

S26361-F1652-L4

Modem external 56kbps (V.90)
MultiTech
MT5643ZBA-Global
international approval
incl. 2m Telephon cord RJ11/RJ11
Adapter Plug RJ11/TAE
Serial Interface cable DB25m / DB9f
AC-Adapter w. German Power Cord
occupies one COM port
max. 1x per system

In connection with rack configurations
the install variant of the modem
(S26361-F1652-E4) has to be ordered
(see rack configurator)

K

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

16 of 18

System configurator and order-information guide

K

PRIMERGY TX150 S4 Status 25.11.2005

Section

PRIMERGY TX150 S4 Floorstand PRIMERGY TX150 S4 Rack

Power cord for following countries:

1,8 m, grey Country specific power cords are not

T26139-Y1740-E10 D, A, B, F, NL, FIN, S, N, E, P, RUS, TR &Canada. Power cords are shipped in a rack

XII

Country specific / rack specific options

A country specific power cord has to be ordered for all floorstand versions:

- once per basic unit and an additional second cable

- if an second hot plug, redundant power supply modul is ordered.

required for rack versions, except for USA

max. T26139-Y1742-E10 USA, Canada version with inlet connector for non-heating
2 x T26139-Y1743-E10 Switzerland apparatus. (1x with Standard PSU,

T26139-Y1744-E10 UK, Ireland 2x with hot plug upgrade)
T26139-Y1745-E10 Italy
T26139-Y1746-E10 Denmark T26139-Y1742-E10 USA, Canada
T26139-Y3850-E10 No power cord as order option For shipments to USA&Canada, you have to order

Attention: For connection of a monitor
to the system an additional country
specific power cord has to be
ordered as option.

Power cord for optional monitor connection for the following countries:

1.8m, grey

one power cord (1,8m, grey) per power supply.

T26139-Y1740-L10 D, A, B, F, NL, FIN, N, S, E, P, RUS, TR
T26139-Y1742-L10 USA, Canada
T26139-Y1743-L10 Switzerland
T26139-Y1744-L10 UK, IR
T26139-Y1745-L10 Italy
T26139-Y1746-L10 Denmark

Powercord 3-way splitter 1M to 3F

0.78m, grey
T26139-Y3692-L1
Adapter for the connection of up to 3 PS-modules or up to
2 PS-modules and one monitor to the mains connection.
Both, standard and hot plug power supplies, are supported.

Other options and Peripherals

For other options refer to the section "Product-specific options
These options are supplied loose with the shipment.
For suitable peripherals for this product refer to the section "Peripherals/communication".

Option for Floorstand

keyboards for floorstand versions for following countries:

S26381-K397-E110 USA / international
S26381-K397-E120 Germany
S26381-K397-E140 France
S26381-K397-E155 Sweden / Finland
S26381-K397-E165 United Kingdom
S26381-K397-E180 Spain
S26381-K397-E185 Italy

End PRIMERGY TX150 S4

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

17 of 18

System configurator and order-information guide

PRIMERGY TX150 S4 Status 25.11.2005

Cange Report

Date

Order number

Changes

2005-11-23 S26361-F1809-E2 ISDN SO Controller PCI Eicon Diva Server BRI-2M 2.0 - now available
2005-03-31 First release

Fujitsu Siemens Computers

Enterprise Products - PRIMERGY Server

18 of 18