How it Works
FUJIFILM
Loading...
FINEPIX 6800
User Manual
11 pgs1.61 Mb0
SERVICE GUIDE
74 pgs5.46 Mb0
SERVICE MANUAL
21 pgs4.19 Mb0
SHEMATICS
25 pgs4.73 Mb0
PARTS LIST
22 pgs3.39 Mb0
Table of contents
Loading...

FUJIFILM FinePix 6800 SERVICE GUIDE

DIGITAL CAMERA
FinePix6800Zoom
SERVICE GUIDE
U/E/EG_Model
WARNING
IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PREASE REPLACE ONLY BY THE COMPORNENTS SPECIFIED ON THE SCHEMATHIC DIAGRAM
AND IN THE PARTS LIST.
IF YOU USE WITH PART NUMBER UN-SPECIFIED, IT MAY RESULT IN A FIRE AND AN
ELECTORICAL SHOCK.
FUJI PHOTO FILM CO.,LTD.
Printed in Japan 2001.03(M.A)
Ref.No.:ZM00357-100

SAFETY CHECK-OUT

After correcting the original problem, perform the following safety check before return the product to the costomer.
FinePix6800Zoom(U/E/EG) SREVICE GUIDE
1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splasher and bridges.
2. Check the interboard wiring to ensure that no wires are ìpinchedî or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
4. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
5. Check the B + voltage to see it is at the values specified.
6. Make leakage - current measurements to determine that exposed parts are acceptably insulated from the supply circuit before returning the product to the customer.
7. CAUTION: FOR CONTINUED
PROTECTION AGAINST FIRE
2.5A125V
2.5A125V
RISK OF FIRE­REPLACE FUSE AS MARKED
HAZARD, REPLACE ONLY WITH SAME TYPE 2.5 AMPERES 125V FUSE. ATTENTION: AFIN D'ASSURER UNE PROTECTION PERMANENTE CONTRE LES RISQUES D'INCENDIE, REMPLACER UNIQUEMENT PAR UN FUSIBLE DE MEME, TYPE 2.5 AMPERES, 125 VOLTS.
8. WARNING:
WARNING!
HIGH VOLTAGE
TO REDUCE THE ELECTRIC SHOCK, BE CAREFUL TO TOUCH THE PARTS.
2
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
TABLE OF CONTENTS
1.Specifications
1-1.Product Specification .............................................................................................................................. 4
2. Names of Components
2-1.Names of Extsrnal Components ............................................................................................................ 6
2-2.Names of Internal Components ............................................................................................................. 7
3. Disassembly
3-1.Removing R PANEL ................................................................................................................................8
3-2.Removing BODY/LENS CONST ............................................................................................................ 9
3-3.Removing ST PWB UNIT/XE PWB UNIT ............................................................................................ 10
3-4.Removing LENS CONST ...................................................................................................................... 11
3-5.Removing DC PWB ASSY .................................................................................................................... 11
3-6.Removing MAIN PWB ASSY ................................................................................................................ 12
3-7.Removing BATTERY CONNECTOR,PWB HOLDER......................................................................... 12
3-8.Removing MODE DIAL,B/W LCD,KEY PWB ASSY........................................................................... 13
3-9.Removing BARRIER MOTOR HEAD/LENS BARRIER ..................................................................... 14
TABLE OF CONTENTS
Page
4. Adjustment and Check
4-1.Important Point of Adjustment when Replacing Major Parts ............................................................ 15
4-2.Preparation for the adjustment ............................................................................................................ 15
4-2-1.Measuring Instrument Used .......................................................................................................... 15
4-2-2.List of Jigs Used ............................................................................................................................. 15
4-2-3.Measuring Intrument and Jig Connection Diagram .................................................................... 16
4-2-4.Environmental Settings .................................................................................................................. 16
4-3.Adjusting by PC ..................................................................................................................................... 17
4-3-1.Various downloading software decompressions, preservation methods,and note. ................ 17
4-3-2.Adjustment software....................................................................................................................... 18
4-3-3.Starting the sdjustment software .................................................................................................. 18
4-3-4.Initialization settings of adjustment software .............................................................................. 18
4-3-5.Command descriptions for[FFW.exe] ........................................................................................... 19
4-3-6.Reading from and writing to EEPROM ......................................................................................... 20
4-3-7. Adjustments...................................................................................................................................... 22
A:B/W LCD adjustment .......................................................................................................................... 23
B:CCD data Input/OFD adjustment ...................................................................................................... 23
C:Mode dial adjustment ......................................................................................................................... 24
D:BATT voltage adjustment .................................................................................................................. 24
E:DC JACK voltage adjustment ............................................................................................................ 25
F:Image sensor adjustment................................................................................................................... 25
[Shutter adjustment],[Apertuer sensitivity adjustment],[ISO sensitivity adjustment] [White barance adjustment],[AE adjustment],[Offsetlevel adjustment]
G:AF adjustment ..................................................................................................................................... 28
H:Flash adjustment ................................................................................................................................29
J:End setting ........................................................................................................................................... 30
4-4.Check ...................................................................................................................................................... 31
4-5.Hexadecimal to decimal Conversion Table ........................................................................................ 31
4-6.Adjustment Addresses
4-6-1.U_MODEL................................................................................................................................32
4-6-2.E/EG_MODEL ......................................................................................................................... 71
5.Troubleshooting ..................................................................................................... 72
6.Appendix ................................................................................................................ 73
3

1.Specifications

FinePix6800Zoom(U/E/EG) SERVICE GUIDE
1. Specifications
1-1. Product Specifications
System
Model Digital camera FinePix6800 ZOOM Storage media SmartMedia (3.3V) File format Still image: Exif ver.2.1 (JPEG)
Movie: AVI format, Motion JPEG Audio: Exif Ver. 2.1 audio file standard-compliant
Image file size 2832 x 2128 pixels (6.03 million pixels)/2048 x 1536 pixels/1280 x 960 pixels/
640 x 480 pixels Storage media SmartMedia (3.3V) Number of frames recorded
Pixel 2832 x 2128 2048 x 1536 1280 x 960
640 x 480
Movie Audio (Video) recording
Quality Mode FINE
Image Data Size
4MB (MG-4S) 1 3 8 2 6 6 12 44
8MB (MG-8S) 3 6 17 6 13 12 25 89
16MB (MG-16S/SW)
32MB (MG-32S/SW)
64MB (MG-64S/SW)
128MB (MG-128SW)
CCD sensor 1/1.7-inch Super CCD (with primary color filter)
Viewfinder Real image optical Lens Super EBC Fujinon optical 3x zoom lens Aperture F2.8/F7.0 (Wide-angle) to F4.5/F10.8 (Telephoto) Focus TTL contrast-type, Auto or Manual Focus distance f = 8.3 mm - 24.9 mm
Exposure control TTL 64-zones metering, Program AE, exposure compensation available in Manual
Sensitivity Equivalent to ISO 100/200/400 White balance Auto (In Manual modes, 7 positions can be selected.) Focal range Normal: Approx. 60 cm (2.0 ft.) to infinity
Shutter Variable-speed, 3 sec. to 1/2000 sec. (using AE) Flash Auto flash using flash control sensor
LCD monitor 2-inches, low-temperature polysilicon TFT 130,000 pixels Video output NTSC (U.S.A./Canada model)/PAL (Europe model) Self-Timer 10 sec. timer clock
Approx. Approx. Approx. Approx. Approx. Approx. Approx. Approx.
2400KB 1200KB 460KB 1300KB 590KB 620KB 320KB 90KB
NORMAL
6 133312262549163
13 28 68 25 53 50 99 330
26 56 137 50 107 101 198 663
53 113 275 102 215 204 398 1330
The total number of pixels: 3.3 million in an interwoven pattern.
The number of effective pixels: 3.015 million.
(Equivalent to 36 mm - 108 mm on a 35 mm camera)
photography mode
Macro: Approx. 20 cm (0.6 ft.) to 80 cm (2.6 ft.)
Effective range Wide-angle Approx. 0.2 m - 3.5 m (0.6 ft. - 11.5 ft.)
Telephoto Approx. 0.2 m - 2 m (0.6 ft. - 6.6 ft.)
Flash modes: Auto, Red-Eye Reduction, Forced Flash, Slow Synchro
BASIC FINE
NORMAL
FINE
NORMAL NORMAL
Approx. 191 sec.
Approx. 385 sec. Approx. 135 sec.
Approx. 774 sec. Approx. 272 sec.
--
--
Approx. 23 sec. Approx. 8 sec.
Approx. 47 sec. Approx. 16 sec.
Approx. 94 sec. Approx. 33 sec.
Approx. 67 sec.
4
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
Input/Output Terminals
A/V Output Stereo mini- jack (1) Digital USB (1) for image data output with a PC DC Input Socket for specified AC power adapter Cradle connection socket
For connection to supplied cradle
Power supply and Others
Power supply Use one of the following
*Rechargeable Battery NP-80 or AC Power Adapter AC-5V/AC-5VH
Available shots / time using the battery (When fully charged)
1.Specifications
Battery type No. of Shots Auto Play
NP-80
The number of shots shown here is an approximate guide to the number of consecutive shots that can be taken based on 50% flash usage at normal temperatures. However, the actual number of available shots will vary de­pending on the ambient temperature when the camera is used and the amount of charge in the battery. The number of available shots or available shooting time will be lower in cold conditions.
Conditions for use Temperature: 0 degree to +40 degrees
Camera dimensions 80 mm x 97.5 mm x 36.3 mm/3.1 in. x 3.8 in. x 1.4 in. (W/H/D) (not including accessories and attachments) Camera mass (weight)
Weight for photography
Cradle dimensions 80 mm x 53 mm x 80 mm/3.1 in. x 2.1 in. x 3.1 in. (W x H x D)
Cradle mass weight Approx. 125 g/4.4 oz. Cradle I/O terminals Accessories SmartMedia (16MB, 3.3V) (1) NP-80 Rechargeable Battery (1)
Optional Accessories
LCD monitor ON Approx. 120 Approx.1 hour Approx.1 hour
LCD monitor OFF Approx. 250
(+32 degrees Fahrenheit to +104 degrees Fahrenheit) 80% humidity or less (no condensation)
258 g/9.1 oz. (not including accessories, batteries or SmartMedia) Approx. 300 g/10.6 oz. (including batteries and SmartMedia)
DC input socket, digital (USB) socket and connector socket (for camera connection)
Supplied with: Cradle (Picture Cradle) (1) *Anti-static case (1) Hand strap (1)
*Index label (1) Owner's Manual (1) AC Power Adapter AC-5V/AC-5VH (approx. 2 m (6.6 ft.) connection cord) (1) A/V Cable (approx. 1.5 m (4.9 ft.), mini-plug (3.5 mm dia.) to pin-plug cable) (1) Interface Set (1)
*CD-ROM (1)
*Special USB cable with Noise Suppression core (1)
*Software Quick Start Guide (1) SmartMedia
MG-4S: 4MB, 3.3V MG-8S: 8MB, 3.3V MG-16S/SW: 16MB, 3.3V
MG-32S/SW: 32MB, 3.3V MG-64S/SW: 64MB, 3.3V MG-128SW: 128MB, 3.3V AC Power Adapter AC-5V/AC-5VH BC-80 Battery Charger NP-80 Rechargeable Battery PC-AD3 PC Card Adapter Floppy Disk Adapter (FlashPath) SM-R2 Image Memory Card Reader DM-R1 Image Memory Card Reader SC-FX8
-
* With fully charged battery
Audio Recording
Approx.3 hour
5

2.Names of Components

2. Names of Components
2-1.Names of External Components
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
Shutter button
Self-timer lamp
Strap mount
Microphone
Flash control sensor
Lens/Lens Cover
Flash
Viewfinder window
A/V OUT(audio / visual out put)
Digital(USB) socket
DC IN 5V(power input ) socket
(P.52)
socket
Viewfinder
Viewfinder lamp
Mode switch
Power button
DISP button
SmartMedia slot cover release button
SmartMedia slot cover
SmartMedia slot
LCD monitor
OPEN(Flash pop-up ) button
Mode dial
BACK button
Display panel
4-direction ( ) button
Speaker
MENU/OK button
Battery cover
Tripod mount
Cradle connection socket /
Connection socket cover
6
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
2-2.Names of internal Components
R PANEL
MODE DIAL ASSY
B/W LCD
KEY PWB ASSY
2. Names of Components
R PANEL ASSY
F PANEL
BATTERY CONNECTOR
PWB HOLDER
SPEAKER ASSY
MIC ASSY
B COVER ASSY
ST PWB UNIT
XE PWB UNIT
LCD
M FRAME ASSY
MAIN PWB ASSY
LENS BARRIER
F PANEL ASSY
DC PWB ASSY
LENS CONST
BARRIER MOTOR HEAD
7

3. Disassembly

FinePix6800Zoom(U/E/EG) SERVICE GUIDE
3. Disassembly
3-1.Removing R PANEL ASSY
(Remove in the order indicated by circled numbers.)
[Procedure]
(1)Screw x 2 (#1 M1.7 x 3.5)
(2)Screw x 3 (M1.7 X 3.5)
(3)Screw x 1 (#1 M1.7 x 2)
(4)BATTERY COVER
(5)R PANEL ASSY
1
(6)FFC
5
3
2
4
1
6
8
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
3-2.Removing Body/LENS CONST
(Remove in the order indicated by circled numbers.
[Procedure]
(1)Discharge
1
(2)Body(LENS CONST/MAIN PWB ASSY/ST CONST)
3. Disassembly
2
(3)FFC Attention in assembling
It is a thing of attention to the wiring for the flash harness.
3
9
3. Disassembly
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
3-3.Removing ST PWB UNIT,XE PWB UNIT
(Remove in the order indicated by circled numbers.)
[Procedure]
(1)FFC
1
(2)Flash pop-up detection SW
2
(3)XE PWB UNIT
-2
3
-1
3
Attention in assembling Wire for the MIC harness under the capacitor(C819) after
installing ST PWB UNIT.
(4)Hook
(5)ST PWB UNIT
4
5
10
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
3-4.Removing LENS CONST
(Remove in the order indicated by circled numbers.)
[Procedure]
(1)FFC x 2
(2)LENS CONST
1
3. Disassembly
2
1
3-5.Removing DC PWB ASSY
(Remove in the order indicated by circled numbers.)
[Procedure]
(1)Harness x 2 (MIC,SPEAKER)
(2)FFC(LCD PANEL)
(3)Screw x 1 (M1.7 x 3.8Ni)
(4)MAIN PWB ASSY lift and open.
1
4
3
1
(5)Harnes (BATTERY,LCD PANEL)
(6)Screw x 1 (M1.7 x 3.8Ni)
(7)DC PWB ASSY
5
7
6
2
5
11
3. Disassembly
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
3-6.Removing MAIN PWB ASSY
(Remove in the order indicated by circled numbers.)
[Procedure]
(1)Screw X 1 (M1.7 X 3.8Ni)
(2)MAIN PWB ASSY
1
2
3-7.Removing BATTERY CONNECTOR,PWB HOLDER
(Remove in the order indicated by circled numbers.)
[Procedure]
(1)Screw X 1 (M1.7 X 3.0)
(2)PWB HOLDER/BATTERY CONNECTOR
2
1
(3)Hook
(4)PWB HOLDER
3
4
3
12
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
r
3. Disassembly
3-8.Removing MODE DIAL ASSY,B/W LCD,KEY PWB ASSY
(Remove in the order indicated by circled numbers.)
[Procedure]
(1)FFC
(2)Screw x 5 (M1.7 x 3.0)
(3)SW FRAME
(4)MODE DIAL ASSY,B/W LCD,KEY PEB ASSY
2
3
4
Attention in assembling (1)Fit the boss of the B/W LCD to the hole of MODE DIAL ASSY.
1
SW Frame
LCD
(2)Note the position of the SW901 and RP lever of R PANEL.
SW801
FFC
KEY PWB
RP Leve
KEY PWB ASSY
13
3. Disassembly
FinePix6800Zoom(U/E/EG) SERVICE GUIDE
3-9.Removing BARRIER MOTOR HEAD/LENS BARRIER
(Remove in the order indicated by circled numbers.)
[Procedure]
(1)Screw x 2 (M1.7 x 2.0)
(2)BARRIER MOTOR HEAD
1
2
Attention in assembling
Note the position of the hole of the LENS BARRIER
and barrier drive shaft of BARRIER MOTOR HEAD.
14
FinePix6800Zoom(U/E/EG) SERVIS GUIDE

4.Adjustment and Check

4.Adjustment and Check 4-1.Important Point of Adjustment when Replacing Major Parts
After the replacement of the MAIN PWB ASSY,DC PWB ASSY,ST CONST,ST PWB UNIT,XE PWB UNIT,
LENS CONST,MODE DIAL ASSY or B/W LCD make adjustment that are marked in Table.
MAIN PWB ASSY DC PWB ASSY ST CONST ST PWB UNIT XE PWB UNIT LENS CONST MODE DIAL ASSY B/W LCD
Mode dial adj.
DC jack voltage adj.
BATT voltage adj.
B/W LCD adj.
CCD data input
Image sensor adj.
AF adj.
Flash adj.
*1:Please do the Flash adjustment after completing the Image adjustment.
O O
O O O
O O
O*1
O O O O
O*1
O
O O O
O*1 O*1
4-2.Preparation for the adjustment
4-2-1.Measuring Instrument Used
Regurated power supply PC(PC-AT/OS:Win98) Didital voltmeter
Pattern BOX(PTB450) Fluorenscent Light Stand Monitor TV
O
4-2-2.List of jigs Used
Part Name/Model Name Part No. Remakes
Filter LB140 ZJ00006-100 Image system adjustment(Common with the DX-9/DX-7)
AF Chart ZJ00477-100 AF adjustment
Close_up lens(f=600mm) ZJ00007-100 AF adjustment(Common with 8mmVTR/MX500/MX600)(note2)
or f=900mm or ZJ00287-100
Lens holder ZJ00008-100 AF adjustment(Common with 8mmVTR/MX500)(note1)
Stand ZJ00009-100 AF adjustment(Common with 8mmVTR/MX500)(note1)
Base plate ZJ00010-100 AF adjustment(Common with 8mmVTR/MX500)(note1)
Gray Chart(Reflective type) ZJ00254-100 Flash adjustment(Commonwith MX700/MX500)
USB cable FZ03529-100 PC adjustment and communications inspection
CD-ROM FZ04059-100 PC communications inspection
Power cable jig ZJ00213-100 General adjustment(Common with MX700/MX500)
PC adjustment software ZJ00479-100 General adjustment(run under with win98 OS only) (note3)
AC adapter(AC-5VN/AC-5VH/AC-5VS
DSC jig driver setup ZJ00476-100 DSC jig driver setup(note3)
Li BATT jig ZJ00226-100 BATT voltage adjustment(Common with FinePix4900Zoom)
(note1)
This is a holder set for supporting the conversion lens.for detals,see the figure below.
-----------
Adjustment overall(Common with FinePix4700Zoom)
Lens holder( -40-50/Sigma Optical Devices)
Stand( -32-130/Sigma Optical Devices)
Base plate( -13-3/Sigma Optical Devices)
(note2)
The two close-up lens (f=600mm:ZJ00007-100,f=900mm:ZJ00287-100) can also be used. When using the
f=600 close-up lens, or f=900mm close-up lens, be caraful of the alloowancs at setting distance.
(note3)
Please download [PC adjustment software] and [DSC jig driver setup] from Web server [Intranets.com].
Web server [Intranets.com]===(http://fujifilm-di.intranets.com/)
15
4.Adjustment and Check
FinePix6800Zoom(U/E/EG) SERVIS GUIDE
4-2-3.Measuring Instrument and Jig Connection Diagram
FinePix6800Zoom
USB Terminal
DC_IN Terminal
Power Cable Jig
Digital Voltmeter
(note1)
Digital Voltmeter
(note1)
USB Cable
Reguratted power supply
Li BATT Jig
(note1)Please sence input voltage at DC_IN terminal in case of System block adjustment.
4-2-4.Environmental Settings
(1)Environmental Setting for Image System Adjustment(Fig.A)
<<Full White Pattern>> Remove the chart from the pattern box. Position the camera (lens surface when the power is on) and pattern box so that they are separated by approximately 5 cm. Arrange so that the standards for the pattern box are as follows.
1. Brightness: 160+-5 cd/m
2
(with LB140 filter) No chart - Center of pattern box. Minolta luminous meter LS-110
2. Color warmth: 6100+-50
o
K (with LB140 filter) No chart - Center of pattern box. Minolta colormeter F
camera
Body
Personal Computer
DC5V
DC5V
Reguratted power supply
50+-5mm
Filter(LB140)
Fig.A
Pattern
BOX
(2)Environmental Setting for Flash Adjustment/Inspection(Fig.B)
The strobe adjustment is easily affected by other sources of light. Make the area around the gray chart extremely dark to minimize the affects of other sources of light. Position 100 cm from the camera (lens surface).
camera
Body
Gray chart standards Gray chart should be Superior Oxford Gray (No. 22) and a material with a reflection ratio of 18+-0.7%.
(3)Environmental Setting for AF Adjustment(Fig.C)
30+-5mm
1.The distance from the camera to the AF chart is set with
conversion lenses of the f=600mm or 900mm as shown in a right picture.
2.The AF chart is shone on by using the source of light. Please give brightness on the surface of the AF chart as
9.0-12.0Ev.
3.Please set the lens position of the camera on the concen-
tric circle about the conversion lens.
oWhen the f=600mm close-up lens is used
During INF,600mm adjustment 620+-5mm
200mm adjustment 220+-5mm
oWhen the f=900mm close-up lens is used
During INFadjustment920+-5mm
600mm adjustment 620+-5mm
200mm adjustment 220+-5mm
100cm
Gray chart
Fig.B
Fluorenscent
Light Stand
AF Chart
Fig.C
16
FinePix6800Zoom(U/E/EG) SERVIS GUIDE
4.Adjustment and Check
4-3.Adjustment by PC
4-3-1.Various downloading software de-
compressions, preservation methods,
and note.
The firmware and the PC adjustment software are in a spec­ified Web server, and both of these are the compression of zip from files. Thesefore, after downloading these compression files from the zip from the Web server, the decompression of the file is necessary. In the decompression software, if the decompression of the zip from can be done, any software is OK. (Please prepare each one for the decompression software.) The decompression and the presevation method of the PC adjustment software and the firmware are described to the following.
(1)The PC adjustment soft decompression and preservation method. <STEP1> Download compressed PC adjustment software(ZJ00479­100zip) from Web server(http://fujifilm-di.intranets.com/) <STEP2> Defrost the downloaded compression software. (Note) *Specify the presevation drive for C drive if it is decompres­sion software which can specify the preservation drive. *Similarly, defrost without making anew folder itf it is decom­pression software which can be defrosted without making a new folder. *Defrost simply if the decompression software which you have cannot specify the drive specification and the folder making. <STEP3> The folder named ZJ00479-100 can be made by defrosting without specifying anything.(Fig.1) Then,copy the folder named Fx6800Zoom in this folder C drive.(Fig.2) The folder of ZJ00479-100 becomes unnecessary at the end, and delete this folder.
C:DRIVE
ZJ00479-100
Fx6800Zoom
Fig.1 Fig.2
(Caution)[Important] (a)PC adjustment software can not start when there is folder of Fx6800Zoom in folder named ZJ00479-100.(Fig.1) Please preseve the folder of the Fx6800Zoom right under C drive.(Fig.2) (b)Please do not change the folder named Fx6800Zoom. PC adjustment software can not start when folder name is changed.
C:DRIVE
ZJ00479-100
Fx6800Zoom
(2)Firmware decompression and pressrvation method. <STEP1> Download compressed firmware(ZJ00484-
100.zip[U_MODEL] or ZJ00485-100.zip[E/EG_MODEL]) from Web server(http://fujifilm-di.intranets.com/). <STEP2> Defrost the downloaded compression software. <STEP3> As the folder named ZJ00484-100[U_MODEL] or ZJ00485­100[E/EG_MODEL]can be mede by simply defrosting;(Fig­[1]) All files are copied in SmartMedia(more than 4MB:3.3V pecification) in this folder including the folder named imfidx10(Fig-[2]
C:DRIVE
ZJ00484-100 or ZJ00485-100
imfidx10
[1]
[2]
Fig.
(Caution)[Important] (a)Download should use Smart Media. (b)Please format Smart Media with the camera. (c)When the folder named imfidx10 is changed, the firmware cannot be downloaded.
(3)Install the USB jig driver and the PC adjustment software.
* Since this camera uses the USB for communications with
the personal computer, in order to start the PC adjust-
ment software, [the USB jig driver] needs to be installed
in the personal computer beforehand.
* The USB jib driver is the same as that for the FinePix
6800Z, so if this jig driver software is already installed in
the personal computer, it is not necessary to install it.
The procedure is given below.
Installation of JIG driver
<step 1>
Setup.exe file (ZJ00476-100) is downloaded from Web
server (http://fujifilm-di.intranets.com/).
<step 2>
Double click on [setup.exe], then install the [FUJI FILM
DSC Jig Driver].
<step 3>
Install the software in [C:\ProgramFiles\Fjig]
according to the instructions on the PC's screen.
<step 4>
Install the software in [C:\ProgramFiles\Fjig]
according to the instructions on the PC's screen.
17
4.Adjustment and Check
FinePix6800Zoom(U/E/EG) SERVIS GUIDE
4-3-2.Adjustment software
This adjustment software is operated from the user's program (Fx6800.ff)
A:B/W LCD adjustment B:CCD data Input/OFD adjustment C:Mode dial adjustment D:BATT voltage adjustment E:DC JACK votage adjustment F:Image sensor adjustment G:AF adjustment H:Flash adjustment I:Download
J:End setting *F:Image sensor adjustment progresses automatically whenever [Enter] is pushed in order of [shutter adjust­ ment],[ Apertuer sensitivity adjustment],[ISO sensitivity adjustment],[WB adjustment],[AE adjustment] and [off­ setlevel adjustment].
4-3-3.Starting the adjustment software
(1)Double click the Fx6800Zoom folder icon C drive.(Fig.3) (2)Double click ffw216.exe.(Fig.4)
Click [Select user program] and select file "Fx6800.ff" (Fig.7)
Fig.7
Click [Select editor] and select file "Notepad.exe"(Fig.8)
Fig.3
4-3-4.
The initialization settings have already been written to a file
After FFW.exe has been started (see 4-3-3), click [Setting]
(1)Compile
Initialization settings of adjustment software
named "***.ini". The following procedures are only for con­firming the contents. Note that changing file names will cause the software to malfunction.
on the menu bar to display [OKNG clear], [Mode setting] and [Auto Adjustment]. Click [Mode setting]. (Fig. 5)
Fig.5
This sets the selection of the user program and the notepad used for editing. From the [Customize] dialog box, select [Compile]. (Fig.6)
Fig.4
Fig.8
(2)EVR & Comm
This performs the communication settings with EVR.
From the [Customize] dialog box, select [EVR] for set-
ting. (Fig.9)
LANC page check Check
Item Settings
etc(-V2) Check
Fig.9
(3)Hardware
From the [Customize] dialog box, select [Hardware]. Se-
lect [Debug Mode]. (Fig. 10)
Debug Mode Ignore Focus I/O
18
Fig.10
Fig.6
FinePix6800Zoom(U/E/EG) SERVIS GUIDE
4.Adjustment and Check
(4)Etc.
From the [Customize] dialog box, select [Etc.]. This is
used for other settings. (Fig. 11)
of auto-measure O
Change mode Do not check(=not used)
Use Japanese font Do not check(=not used)
In [Etc.], setting [Don't show OK NG] to off will allow
[OK] to be displayed on the computer screen if the
adjustment is good and [NG] to be displayed if it is
bad. (Either setting can be used.)
Fig.11
(5)Apply & OK
This saves the settings made in [Customize].
(Fig. 12)
*Always click [Apply] and [OK] after all
the settings have been completed.
This will save the settings.
(2)
Fig.12
(1)
4-3-5.
Command descriptions for [FFW.exe]
Fig.13
Menu Command Contents
Operation Start Start of the program
Stop Stop of the program
Halt Halt of the program
Step0 Don't use it(note.1)
End Closes of the program
Program Re_load
Select
Edit
Data ad[] Don't use it(note.1)
rd[] Don't use it(note.1)
SW Don't use it(note.1)
fsw Don't use it(note.1)
EVR
Mode Fili Recording Don't use it(note.1)
NGSTOP
STEP Don't use it(note.1)
LINE Don't use it(note.1)
AUTO Don't use it(note.1)
Setting OKNG clear Don't use it(note.1)
Mode setting Mode setting
Auto Adjustment
Help Help
Help(FF)
FOCAS It isn't used
Version
Re_load of the program
(*.ff) (note.2)
Select of the program(*.ff)
Edit of the program(*.ff)
Data to the EEPROM are writ-
ten/read.(4-3-5 reference.)
When adjustment is ng,
a program is given up once.
A setup of practice of "Auto
Adjust" in the user program
Help for the bacic software
Help for the user program
The version information
of the basic software
Precautions when making
adjustments
O:After adjustments have been completed,
the DC power supply of the camera is pulled out forcibly, and adjustment is fin­ished.
O:If the power switch for the camera has been
set to off during adjustment mode (during camera service mode), disconnect the DC input terminal and then reconnect it be­fore turning the power for the camera on again.
O:If a [NG] appears during adjustment and the
program stops, restart the adjustment soft­ware and redo the adjustment.
(Note 1) : Please refer to the help section of the basic
software for details.
(Note 2) : Always reload after editing the program.
While the user program can be edited, it should
never be performed unless specified as changes to
the program could cause it to malfunction.
19
4.Adjustment and Check
FinePix6800Zoom(U/E/EG) SERVIS GUIDE
4-3-6.
Reading from and writing to EEPROM
As with the remote controller for adjustment (RM95B), this adjustment program allows data to be read from and written to the EEPROM. The following is the procedure for doing this. (1)Start the user program and arrange so that there is com-
munication between the PC and DS camera.
(Note) Refer to the following for the procedure for start-
ing the user program.
(2)From the FFW.exe menu bar, click [Data] and select EVR.
(Fig. 14)
(This mode can be operated even when the user program
is in operation.)
Fig.14
(3)The EVR data is displayed.
The meaning of the items in the EVR data menu bar is shown in Fig. 15.
Fig.16
The example above shows when page 4 has been en-
tered and 02h has been entered.
(4)EVR data save/write
Click from the EVR data dialog box. (Fig. 17)
Fig.17
Open the EVR file selection dialog box. (Fig. 18) Select the location for saving, enter the file name and click [Save]. (In the example, the file is being saved in Fx6800Zoom of the C: drive under the file name of "Fx6800" .
Fig.15
Item Description Meaning
Switch between decimal and hexadecimal display.
Redraw Redisplays the EVR data.
ROM read Reads the EEPROM data.
ROM write Writes data to EEPROM.
RAM read Reads RAM data.
+1_RAM write
-1_RAM write
Record Saves EVR data.
ROM screen
RAM screen
Page designation
Address designation
An actual example of when page or address designation is used
on the EVR data screen can be seen in Fig. 16 .
Switches the EVR data display between decimal and hexadecimal.
Increased the designated ad­dress by +1. (Not performed when writing data to EEPROM.)
Increased the designated ad­dress by -1. (Not performed when writing data to EEPROM.)
Reads one page (address 256h) of ROM data.
Reads one page (address 256h) of RAM data.
Page designation (Moves to designated page.)
Address designation (Moves to designated address.)
Fig.18
Click [Save] and the Rec. EVR dialog box will open. (Fig. 19). The possible selections are: [Write file, [Read file_write RAM] and [Read file_write ROM]. The following explains the meaning of each.
Writw file Saves EVR data.
Read file
Write RAM (Does not write to file.)
Read file Writes the data value
Write ROM in the file.
Select [Write file]. Check the required page (multiple
selections possible). (Fig. 19)
*Up to page F is OK for FinePix6800Zoom.
Sets the data value in the file.
Fig.19
20
FinePix6800Zoom(U/E/EG) SERVIS GUIDE
To save the data on a floppy disk, select "A:3.5
inch FD" as the location for saving shown in Fig. 18.
Select start to save.
Once the data has been saved, the EVRdata screen is
displayed.
[RAM file_write RAM] is for setting the data in files
to EVR. As shown in Fig. 18, select a location that
has a file that has already been saved, select the
file name and click [Save]. This will open the Rec.
EVR dialog box. Select [Read file_write RAM] and
click [Start]. Since the page will be read from the
selected file at this time, there is no need to
select it.
[Read file_write ROM] writes files that have data to
EVR. As shown in Fig. 18, select a location that has
a file that has already been saved, select the file
name and click [Save]. This will open the Rec. EVR
dialog box. Select [Read file_write ROM] and click
[Start]. Since the page will be written from the
selected file at this time, there is no need to
select it.
4.Adjustment and Check
When Read file_write RAM has been completed, EVR data
will be shown in blue.
Read file_write ROM has been completed, EVR data will
be shown in red.
21
4.Adjustment and Check
4-3-7. Adjustments
(1) Execute [Operation] -> [Start] (Fig. 18)
(2) When [Operation] -> [Start] is executed, follow the
instructions that are displayed in the instruction window
(Fig. 19). Press Enter when you are done. In Item 1, remote sensing is done by providing an input voltage at the DC_IN terminal. Use care to keep the voltage from falling. Since PC recognition is performed in Item 4, the CD-ROM for Windows 98 may be requested. If this occurs, follow the instructions. Once the PC recognition process has been completed, press Enter.
FinePix6800Zoom(U/E/EG) SERVIS GUIDE
Fig.18
Fig.19
(3) The FirmWare version will be displayed. [U_MODEL]
Please download FirmWare Ver. 2.20(ZJ00484-100)
if FirmWare Ver. is not 2.20.
[E/EG_MODEL]
Please download FirmWare Ver. 3.20(Zj00485-100)
if FirmWare Ver. is not 3.20.
Please download [U_MODEL:FirmWare Ver. 2.20] and
[E/EG_MODEL:FiemWare Ver. 3.20] from Web server
[Intranets.com].
Web server [Intranets.com]===(http://fujifilm-di.intranets.com/)
Next, press Enter to open the USB port. (Fig. 20)
[Fig. is U_MODEL]
(4) Pressing Enter will open the USB port, and the adjustment
item menu is displayed. (Fig. 21)
Fig.20
How to accomplish each of the adjustments is described below.
22
(Fig.21)
FinePix6800Zoom(U/E/EG) SERVIS GUIDE
A: B/W LCD adjustment
Press A on your PC keyboard to select A: B/W LCD adjustment from the adjustment menu. The LCD character adjustment screen will be displayed. Follow the instructions given. (Fig. 22)
Confirm that the displayed contrast is black enough, and that there is no cross-talk. (Fig. 23)
4.Adjustment and Check
(Fig.22)
Cross talk(Shadow)
Press Enter to input the B/W LCD adjustment and complete the operation. Press Enter to return to the menu. (Fig. 24)
B: CCD data Input/OFD adjustment
Press B on your PC keyboard to select B: CCD data Input/ OFD adjustment from the adjustment menu. When the 8-character filename input dialog is opened, insert the floppy disk containing LENS CONST into the A: Drive, input the file name, then press [OK]. (Fig. 25)
Fig.23
(Fig.24)
Fig.25
23
Loading...
+ 51 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use