FORD F-250, F-550, F-450 SD, F-350 User Manual

Download

Page 1

Introduction 4

Instrument Cluster 12

Warning and control lights 12 Gauges 16

Entertainment Systems 20

AM/FM stereo 20 AM/FM stereo with CD 22 AM/FM stereo cassette with CD 25 AM/FM stereo with in-dash six CD 28

Climate Controls 34

Heater only 34 Manual heating and air conditioning 35 Electronic automatic temperature control 37

Table of Contents

Lights 40

Headlamps 40 Turn signal control 46 Bulb replacement 47

Driver Controls 55

Windshield wiper/washer control 55 Steering wheel adjustment 56 Moon roof 57 Power windows 58 Mirrors 60 Speed control 63 Message center 67

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 2

Table of Contents

Locks and Security 80

Keys 80 Locks 80

Seating and Safety Restraints 90

Seating 90 Safety restraints 97 Air bags 108 Child restraints 117

Tires, Wheels and Loading 129

Tire Information 132 Tire Inflation 133 Changing tires 137 Lug Nut Torque 148 Vehicle loading 160 Trailer towing 165 Recreational towing 174

Driving 175

Starting 175 Brakes 181 Transmission operation 184

Roadside Emergencies 211

Getting roadside assistance 211 Hazard flasher switch 212 Fuel pump shut-off switch 213 Fuses and relays 213 Jump starting 221 Wrecker towing 227

Customer Assistance 229

Reporting safety defects (U.S. only) 237

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 3

Table of Contents

Cleaning 238

Maintenance and Specifications 245

Engine compartment 247 Engine oil 249 Battery 253 Fuel information 261 Air filter(s) 278 Part numbers 280 Refill capacities 281 Lubricant specifications 283

Accessories 296

Index 299

All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 4

Introduction

CALIFORNIA Proposition 65 Warning

WARNING: Engine exhaust, some of its constituents, and

certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

CONGRATULATIONS

Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle, the greater the safety and pleasure you will derive from driving it.

For more information on Ford Motor Company and its products visit the following website:

• In the United States: www.ford.com

• In Canada: www.ford.ca

• In Australia: www.ford.com.au

• In Mexico: www.ford.com.mx

Additional owner information is given in separate publications.

This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available.

Remember to pass on this Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle.

Fuel pump shut-off switch: In the event of an accident the

safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside Emergencies chapter.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 5

Introduction

SAFETY AND ENVIRONMENT PROTECTION

Warning symbols in this guide

How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.

Warning symbols on your vehicle

When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.

Protecting the environment

We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste, cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.

BREAKING-IN YOUR VEHICLE

Your vehicle does not need an extensive break-in. Try not to drive continuously at the same speed for the first 1,000 miles (1,600 km) of new vehicle operation. Vary your speed frequently in order to give the moving parts a chance to break in.

Drive your new vehicle for at least 500 miles (800 km) before towing a trailer or snowplowing.

Do not add friction modifier compounds or special break-in oils during the first few thousand miles (kilometers) of operation, since these additives may prevent piston ring seating. See Engine oil in the Maintenance and Specifications chapter for more information on oil usage.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 6

Introduction

SPECIAL NOTICES

Emission warranty

The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.

Service Data Recording

Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and service your vehicle, Ford Motor Company, Ford of Canada, and service and repair facilities may access vehicle diagnostic information through a direct connection to your vehicle when diagnosing or servicing your vehicle.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 7

Introduction

Event Data Recording

Other modules in your vehicle — event data recorders — are capable of collecting and storing data during a crash or near crash event. The recorded information may assist in the investigation of such an event. The modules may record information about both the vehicle and the occupants, potentially including information such as:

• how various systems in your vehicle were operating;

• whether or not the driver and passenger seatbelts were buckled;

• how far (if at all) the driver was depressing the accelerator and/or the

brake pedal;

• how fast the vehicle was traveling; and

• where the driver was positioning the steering wheel.

To access this information, special equipment must be directly connected to the recording modules. Ford Motor Company and Ford of Canada do not access event data recorder information without obtaining consent, unless pursuant to court order or where required by law enforcement, other government authorities or other third parties acting with lawful authority. Other parties may seek to access the information independently of Ford Motor Company and Ford of Canada.

Special instructions

For your added safety, your vehicle is fitted with sophisticated electronic controls.

Please read the section Supplemental restraint system (SRS)

in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury.

Front seat mounted rear-facing child or infant seats should

NEVER be placed in front of an active passenger air bag.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 8

Introduction

Notice to owners of diesel-powered vehicles

Read the 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for information regarding correct operation and

maintenance of your Diesel-powered light truck.

Notice to owners of pickup trucks and utility type vehicles

Utility vehicles have a significantly higher rollover rate than

other types of vehicles.

Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type, failure to operate this vehicle correctly may result in loss of vehicle control, vehicle rollover, personal injury or death.

Be sure to read Driving off road in the Driving chapter.

Using your vehicle with a snowplow

For more information and guidelines for using your vehicle with a snowplow, refer to the Driving chapter.

Using your vehicle as an ambulance

If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete

Vehicle Manual, Ford Truck Body Builder’s Layout Book and the Qualified Vehicle Modifiers (QVM) Guidelines as well as pertinent

supplements. For additional information, please contact the Truck Body Builders Advisory Service at 1–877–840–4338.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 9

Introduction

Use of your Ford light truck as an ambulance, without the Ford Ambulance Preparation Package voids the Ford New Vehicle Limited Warranty and may void the Emissions Warranties. In addition, ambulance usage without the preparation package could cause high underbody temperatures, overpressurized fuel and a risk of spraying fuel which could lead to fires.

If your vehicle is equipped with the Ford Ambulance Preparation Package, it will be indicated on the Certification label. The label is located on the driver’s side door pillar or on the rear edge of the driver’s door. You can determine whether the ambulance manufacturer followed Ford’s recommendations by directly contacting that manufacturer. Ford Ambulance Preparation Package is only available on certain 6.0L Diesel engine equipped vehicles.

Using your vehicle as a stationary power source (PTO)

Refer to the Driving chapter for more information and guidelines for operating a vehicle equipped with an aftermarket power take-off system.

Middle East/North Africa vehicle specific information

For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner’s Guide; therefore, a supplement has been supplied that complements this book. By referring to the pages in the provided supplement, you can properly identify those features, recommendations and specifications that are unique to your vehicle. Refer to this

Owner’s Guide for all other required information and warnings.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 10

Introduction

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

Fasten Safety Belt Air Bag-Front

Air Bag-Side Child Seat

Child Seat Installation Warning

Child Seat Tether Anchor

Anti-Lock Brake System

Powertrain Malfunction Speed Control

Master Lighting Switch Hazard Warning Flasher

Fog Lamps-Front Fuse Compartment

See Owner’s Guide

Child Seat Lower Anchor

Brake System

Brake Fluid Non-Petroleum Based

Fuel Pump Reset Windshield Wash/Wipe

Windshield Defrost/Demist

Rear Window Defrost/Demist

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 11

Vehicle Symbol Glossary

Introduction

Power Windows Front/Rear

Child Safety Door Lock/Unlock

Power Window Lockout

Interior Luggage Compartment Release Symbol

Panic Alarm Engine Oil

Engine Coolant

Engine Coolant Temperature

Do Not Open When Hot Battery

Avoid Smoking, Flames, or Sparks

Battery Acid

Explosive Gas Fan Warning

Power Steering Fluid

Maintain Correct Fluid Level

Emission System Engine Air Filter

MAX

MIN

Passenger Compartment Air Filter

Jack

Check fuel cap Low tire warning

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 12

Instrument Cluster

WARNING LIGHTS AND CHIMES

Standard instrument cluster (manual transmission)

Standard instrument cluster (automatic transmission)

Harley—Davidson instrument cluster

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 13

Instrument Cluster

Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulbs work. If any light remains on after starting the vehicle, have the respective system inspected immediately.

If your vehicle is equipped with a Diesel engine, it has a unique cluster, refer to Starting the engine in your 6.0 Liter Power Stroke Direct

Injection Turbo Diesel Owner’s Guide Supplement.

Service engine soon: The Service engine soon indicator light

illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

Under engine misfire conditions, excessive exhaust temperatures

could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.

Electronic throttle control:

Illuminates when the engine has defaulted to a ’limp-home’ operation. Report the fault to a dealer at the earliest opportunity.

On vehicles equipped with a message center, “ENGINE FAILSAFE MODE” will be displayed, refer to Message Center in the Driver Controls chapter.

Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON

BRAKE

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 14

Instrument Cluster

position. If the brake system warning light does not illuminate at this time, seek service immediately from your dealership. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your servicing dealership.

Driving a vehicle with the brake system warning light on is

dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your dealer immediately.

Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately. Normal braking is still functional unless the brake warning light also is illuminated.

Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately. A chime will also sound when a malfunction in the supplemental restraint system has been detected.

Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt.

ABS

Charging system: Illuminates when the battery is not charging properly.

Transmission Tow/Haul Feature (automatic transmission):

Illuminates when the Tow/Haul feature has been activated. Refer to the Driving chapter for transmission function and operation. If the light flashes steadily, have the system serviced immediately, damage to the transmission could occur.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 15

Instrument Cluster

Four wheel drive low: Illuminates when four-wheel drive low is engaged.

Four wheel drive indicator:

Illuminates when four-wheel drive is engaged.

Speed control: Illuminates when the speed control is activated. Turns off when the speed control system is deactivated.

Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb.

High beams: Illuminates when the high beam headlamps are turned on.

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF, LOCK or ACCESSORY position and the driver’s door is opened.

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and the driver’s door is opened.

Parking brake ON warning chime: Sounds when the parking brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km).

LOW

RANGE

4x4

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 16

Instrument Cluster

GAUGES

Speedometer: Indicates the current vehicle speed.

Standard instrument cluster

Harley—Davidson instrument cluster

Engine coolant temperature gauge: Indicates engine coolant

temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section,

the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.

Never remove the coolant reservoir cap while the engine is

running or hot.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 17

Instrument Cluster

Odometer: Registers the total miles (kilometers) of the vehicle.

• With Mini Message Center

• With Full Message Center

Refer to Message Center in the Drivers Controls chapter on how to switch the display from Metric to English.

Trip odometer: Registers the miles (kilometers) of individual journeys.

• With Mini Message Center

Press and release the SELECT/RESET button on the cluster to toggle between odometer and trip odometer display. To reset, press and hold for less than 2 seconds.

• With Full Message Center

Press and release the message center INFO button until TRIP mode appears in the display. Press the RESET button to reset.

Engine hour meter: Registers the accumulated time the engine has been running.

• With Mini Message Center

Press the SELECT/RESET button until the engine hours display.

• With Full Message Center

Press and release the message center INFO button until ENG HRS XXXX.X appears in the display. Press the RESET button to reset.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 18

Instrument Cluster

Tachometer: Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.

Engine oil pressure gauge:

Indicates engine oil pressure. The needle should stay in the normal operating range (between “L” and “H”). If the needle falls below the normal range, stop the vehicle, turn off the engine and check the engine oil level. Add oil if needed. If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician.

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.

Refer to Filling the tank in the

Maintenance and Specifications

chapter for more information.

Battery voltage gauge (manual transmission only): Indicates the

battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated by arrows), have the vehicle’s electrical system checked as soon as possible.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 19

Instrument Cluster

Transmission fluid temperature gauge (automatic transmission only): If the gauge is in the:

Normal area (normal) - the

transmission fluid is within the normal operating temperature (between “H” and “C”).

Yellow area (warning) — the transmission fluid is higher than normal operating temperature. This can be caused by special operation conditions (i.e. snowplowing, towing or off road use). Refer to Special

Operating Conditions in the Scheduled Maintenance Guide for

instructions. Operating the transmission for extended periods of time with the gauge in the yellow area may cause internal transmission damage.

Altering the severity of the driving conditions is recommended to lower the transmission temperature into the normal range.

Red area (over temperature) — the transmission fluid is overheating. Stop the vehicle to allow the temperature to return to normal range.

If the gauge is operating in the Yellow or Red area, stop the vehicle and verify the airflow is not restricted such as snow or debris blocking airflow through the grill. If the gauge continues to show high temperatures, see your Ford dealer.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 20

Entertainment Systems

AM/FM STEREO SYSTEM (IF EQUIPPED)

/ Tuner: Press to

1. manually go up or down the radio

frequency. Also use in menu mode to select various settings.

2. Audio: Press to access select various settings.

Treble: Press to adjust the treble setting. Use SEEK

Bass: Press to adjust the bass setting. Use

SEEK

Balance: Press to adjust the audio between the left and right speakers.

Use

Fade: Press to adjust the audio between the front and rear speakers.

Use

/ / SEEK, SEEK .

/ / SEEK,

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 21

Entertainment Systems

3. Seek: Press to access the next/previous strong station or track.

4. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.

5. AM/FM: Press to select AM/FM frequency band.

6. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.

7. CLK (Clock): Press to toggle between the clock and radio display. To set the clock: Press and hold CLK until the hours begin to flash.

Press again to set the minutes.

When this audio is used in cargo vans where no rear speakers are installed in the vehicle, fading to the rear speakers will result in no audio output.

/ to manually decrease / increase the hours. Press CLK

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 22

Entertainment Systems

AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED)

/ Tuner: Press to

1. manually go up or down the radio

frequency. Also use in menu mode to select various settings.

2. Phone/mute: Press to mute the playing media. Press again to return to the playing media.

3. Menu: Press to toggle through the following modes:

Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press

MENU to access. Use

When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets.

Bass: Press to adjust the bass setting. Use

/ / SEEK to set.

/ / SEEK .

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 23

Entertainment Systems

Treble: Press to adjust the treble setting. Use / / SEEK .

Balance: Press to adjust the audio between the left and right speakers.

Use

Fade: Press to adjust the audio between the front and rear speakers.

Use

Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind

noise. Press MENU to access and use

Setting the clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed. Use MENU again to disengage clock mode.

If your vehicle is equipped with an in-dash clock, refer to “Setting the clock” in the Driver Controls chapter.

4. Aux: Press to toggle between FES/DVD and AUX modes. If no auxiliary sources are available, NO AUX AUDIO will be displayed.

5. Seek: Press to access the next strong station or track.

/ / SEEK .

/ / SEEK to adjust.

/ to manually increase/decrease Press

6. Text: In CD mode, this feature reads track name, artist name, and disc name (if available).

7. Shuffle: Press to play tracks in random order.

8. Comp (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level.

9. Repeat: Press to repeat the current CD track.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 24

Entertainment Systems

10. Fast forward: Press to manually advance in a CD track.

11. Rewind: Press to manually reverse in a CD track.

12. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.

13. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop.

14. Seek: Press to access the previous strong station or track.

15. AM/FM: Press to select AM/FM frequency band.

16. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.

17. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last.

18. CD eject: Press to eject a CD.

19. CD slot: Insert a CD label side up.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 25

Entertainment Systems

AM/FM STEREO CASSETTE/SINGLE CD SOUND SYSTEM (IF EQUIPPED)

/ Tuner: Press to

1. manually go up or down the radio

frequency. Also use in menu mode to select various settings.

2. Seek: Press to access the next strong station or track.

3. Phone/mute: Press to mute the playing media. Press again to return to the playing media.

4. Menu: Press to toggle through the following modes:

Treble: Press to adjust the treble setting. Use

Bass: Press to adjust the bass setting. Use

/ / SEEK .

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 26

Entertainment Systems

Balance: Press to adjust the audio between the left and right speakers.

Use

Fade: Press to adjust the audio between the front and rear speakers.

Use

Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind

noise. Press MENU to access and use

Setting the clock: Press MENU until SELECT HOUR or SELECT

MINUTE is displayed. Press

hours/minutes.

If your vehicle is equipped with an in-dash clock, refer to “Setting the clock” in the Driver Controls chapter.

Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press

MENU to access. Use

When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets.

Clean tape reminder: After 20 hours of cassette operation, the radio will notify you that it is time to clean the cassette player head. After cleaning the player head, you can clear the reminder through menu control and selecting YES.

5. AUX: Press to toggle between FES/DVD and AUX modes. If no auxiliary sources are available, NO AUX AUDIO will be displayed. To return to radio mode, press AM/FM.

6. Tape eject: Press to eject a tape.

/ / SEEK .

/ / SEEK to adjust.

/ / SEEK to adjust the

/ / SEEK to set.

7. Text: In CD mode, displays track title, artist name, and disc title (if available).

8. Shuffle: Press to play CD tracks in random order.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 27

Entertainment Systems

9. Compress (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level.

10. Repeat: Press to repeat the current CD track.

11. Fast forward: Press to manually advance in a CD track or cassette.

12. Rewind: Press to manually reverse in a CD track or cassette.

13. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.

14. Tape: Insert a tape facing to the right.

15. Tape direction: Press to enter tape mode. Press while in play mode to change which side of the tape is playing.

16. AM/FM: Press to select AM/FM frequency band.

17. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decrease volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.

18. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 28

Entertainment Systems

19. CD eject: Press to eject a CD.

20. CD slot: Insert a CD label side up.

21. Seek:Press to access the previous strong station or track.

22. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop.

When this radio is used in cargo vans where no rear speakers are installed in the vehicle, fading to the rear speakers will result in no audio output.

PREMIUM IN-DASH SIX CD SOUND SYSTEM (IF EQUIPPED)

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 29

1. / Tuner: Press to manually go up or down the radio

frequency. Also use in menu mode to select various settings.

2. Phone/mute: Press to mute the playing media. Press again to return to the playing media.

3. Menu: Press to toggle through the following modes:

Entertainment Systems

Treble: Press to adjust the treble setting. Use

Bass: Press to adjust the bass setting. Use

Balance: Press to adjust the audio between the left and right speakers.

Use

Fade: Press to adjust the audio between the front and rear speakers.

Use

Speed sensitive volume (if equipped): Radio volume automatically changes slightly with vehicle speed to compensate for road and wind

noise. Press MENU to access and use

Setting the clock: Press MENU until SELECT HOUR or SELECT

MINUTE is displayed. Press

hours/minutes.

If your vehicle is equipped with an in-dash clock, refer to “Setting the clock” in the Driver Controls chapter.

Autoset: Allows you to set the strongest local radio stations without losing your original manually set preset stations for AM/FM1/FM2 . Press

MENU to access. Use

When the six strongest stations are filled, the station stored in preset 1 will begin playing. If there are less than six strong stations, the system will store the last one in the remaining presets.

/ / SEEK .

/ / SEEK to adjust.

/ / SEEK to adjust the

/ / SEEK to set.

/ / SEEK .

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 30

Entertainment Systems

4. Aux: Press to toggle between FES/DVD and AUX modes. If no auxiliary sources are available, NO AUX AUDIO will be displayed.

5. Seek: Press to access the next strong station or track.

6. Text: In CD mode, press to display the track name, artist name and disc name (if available).

7. Shuffle: Press to play tracks in random order.

8. Comp (Compression): In CD mode, brings soft and loud CD passages together for a more consistent listening level.

9. Repeat: Press to repeat the current CD track.

10. Fast forward: Press to manually advance in a CD track.

11. Rewind: Press to manually reverse in a CD track.

12. Memory presets: To set a station: Select frequency band AM/FM; tune to a station, press and hold a preset button until sound returns.

13. Scan: Press for a brief sampling of radio stations or CD tracks. Press again to stop.

14. Seek: Press to access the previous strong station or track.

15. AM/FM: Press to select AM/FM frequency band.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 31

Entertainment Systems

17. CD: Press to enter CD mode. If a CD is already loaded into the system, CD play will begin where it ended last.

18. LOAD: Press to load a CD, then select a slot number using the radio presets 1 through 6. If you don’t select a slot within 5 seconds, the radio shall choose the first available slot for you. Press and hold for 2 seconds to auto load up to six CDs.

19. CD eject: Press to eject a CD, then select the desired CD slot using the radio presets 1 through 6. If a slot is not selected within 5 seconds, the radio shall eject the current disc. Press and hold for 2 seconds to auto eject all CDs present in the radio mechanism.

20. CD slot: Insert a CD label side up.

RADIO FREQUENCIES

AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are:

AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz

RADIO RECEPTION FACTORS

There are three factors that can affect radio reception:

• Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception.

• Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 32

Entertainment Systems

• Station overload: When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed.

CASSETTE/PLAYER CARE

Do:

• Use only cassettes that are 90 minutes long or less.

• Tighten very loose tapes by inserting a finger or pencil into the hole

and turning the hub.

• Remove loose labels before inserting tapes.

• Allow tapes which have been subjected to extreme heat, humidity or

cold to reach a moderate temperature before playing.

• Clean the cassette player head with a cassette cleaning cartridge after 10–12 hours of play to maintain good sound/operation.

Don’t:

• Expose tapes to direct sunlight, extreme humidity, heat or cold.

• Leave tapes in the cassette player for a long time when not being

played.

CD/CD PLAYER CARE

Do:

• Handle discs by their edges only. Never touch the playing surface.

• Inspect discs before playing. Clean only with an approved CD cleaner

and wipe from the center out.

Don’t:

• Expose discs to direct sunlight or heat sources for extended periods of time.

• Insert more than one disc into each slot of the CD changer magazine.

• Clean using a circular motion.

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 33

Entertainment Systems

jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs. Please contact your dealer for further information.

AUDIO SYSTEM WARRANTY AND SERVICE

Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 34

Climate Controls

HEATER ONLY SYSTEM (IF EQUIPPED)

1. Fan speed adjustment: Controls the volume of air circulated in the

vehicle.

2. Temperature selection: Controls the temperature of the airflow in

the vehicle.

3. Air flow selections: Controls the direction of the airflow in the

vehicle. See the following for a brief description on each control:

: Distributes outside air through the instrument panel vents.

: Distributes outside air through the instrument panel vents and the

floor vents.

O (OFF): Outside air is shut out and the fan will not operate.

: Distributes outside air through the floor vents.

: Distributes outside air through the windshield defroster vents,

floor vents and demister vents.

: Distributes outside air through the windshield defroster vents and

demister vents. Can be used to clear windshield of fog and thin ice.

Operating tips

• To reduce fog build up on the windshield during humid weather, place the air flow selector in the

• To reduce humidity build up inside the vehicle during cold or warm weather, do not drive with the air flow selector in the OFF position.

• Do not put objects under the front seats that will interfere with the air flow to the rear seats.

• Remove any snow, ice or leaves from the air intake area at the base of the windshield.

position.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 35

Climate Controls

To aid in side window defogging/demisting in cold weather:

1. Select

2. Modulate the temperature control to maintain comfort.

3. Set the fan speed to the highest setting.

4. Direct the outer instrument panel vents toward the side windows.

To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.

MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED)

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

1. Fan speed adjustment: Controls the volume of air circulated in the

vehicle.

2. Temperature selection: Controls the temperature of the airflow in

the vehicle.

3. Air flow selections: Controls the direction of the airflow in the

vehicle. See the following for a brief description on each control.

MAX A/C: Distributes recirculated air through the instrument panel vents and center console vents (if equipped) to cool the vehicle. This re-cooling of the interior air is more economical and efficient. Recirculated air may also help reduce undesirable odors from entering the vehicle. The temperature selection control will not adjust airflow temperature when in MAX A/C mode.

: Distributes outside air through the instrument panel vents and

center console vents (if equipped).

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 36

Climate Controls

: Distributes outside air through the instrument panel vents, floor

vents and center console vents (if equipped).

OFF: Outside air is shut out and the climate system is turned off.

: Distributes outside air through the floor vents.

: Distributes outside air through the windshield defroster vents,

floor vents and demister vents.

: Distributes outside air through the windshield defroster vents and

demister vents.

Operating tips

• To reduce fog build up on the windshield during humid weather, place the air flow selector in the

• To reduce humidity build up inside the vehicle, do not drive with the air flow selector in the OFF position.

• Do not put objects under the front seats that will interfere with the airflow to the rear seats.

• Remove any snow, ice or leaves from the air intake area at the base of the windshield.

• To improve the A/C cool down, drive with the windows slightly open for 2–3 minutes after start up or until the vehicle has been “aired out.”

For maximum cooling performance (MAX A/C) in MAX A/C mode:

• Move the temperature control to the coolest setting.

• Set the fan to the highest speed initially, then adjust in order to

maintain comfort.

To aid in side window defogging and demisting in cold weather:

1. Select

2. Select A/C.

3. Set the temperature control to maintain comfort.

4. Set the fan speed to highest setting.

5. Direct the outer instrument panel vents towards the side windows.

position.

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 37

Climate Controls

AUTOMATIC TEMPERATURE CONTROL SYSTEM (IF EQUIPPED)

A/C

EXT TEMP

Press the AUTO and

AUTO

OFFAUTO

(floor/defrost) controls at the same time and

hold for one second to switch between Fahrenheit and Celsius.

1. A/C: Press to activate/deactivate

air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engages automatically in AUTO,

(defrost), and (floor/defrost).

2. Recirculated air: Press to

activate/deactivate air recirculation in cabin. Recirculated air may reduce the amount of time to cool down the interior of the vehicle and may also help reduce undesired odors from reaching the interior of the vehicle. Recirculation can be engaged manually in any other airflow selection except

(defrost). Recirculation may turn off automatically

in all airflow selections.

3. Defrost:

Distributes outside air through the windshield defroster vents and demister vents. Can be used to clear windshield of fog and thin ice.

4. Fan speed: Press the respective control in order to manually increase or decrease the fan speed. To return to automatic fan operation, press AUTO.

(Floor/defrost): Distributes air through the instrument panel

vents, floor vents and demister vents.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 38

Climate Controls

6. (Floor): Distributes air through the floor vents.

7. floor vents and center console vents (if equipped).

8. center console vents (if equipped).

9. OFF: Outside air is shut out and the climate control system is turned off.

10. Manual override controls: The manual override controls allow you to change the system operation. To return to full automatic control, press AUTO. Refer to controls 5–8 for a brief description of each mode.

11. AUTO: Press to engage full automatic operation, and select the desired temperature using the temperature control. The system will automatically determine fan speed, airflow location, A/C on or off, and outside or recirculated air, to heat or cool the vehicle to reach the desired temperature.

12. EXT Control (if equipped): Press EXT TEMP to display outside temperature. Press again to display cabin temperature settings.

13. Temperature controls: Press to increase or decrease the temperature in the vehicle cabin. Note: The recommended vehicle cabin setting is between 72°F (22°C) and 75°F (24°C).

(Panel/floor): Distributes air through the instrument panel vents,

(Panel): Distributes air through the instrument panel vents and

Operating tips

• To reduce fog build up on the windshield during humid weather, place

the air flow selector in the

• To reduce humidity build up inside the vehicle, do not drive with the

air flow selector in the OFF or with recirculated air engaged.

• Do not put objects under the front seats that will interfere with the

airflow to the rear seats.

• Remove any snow, ice or leaves from the air intake area at the base of

the windshield.

position.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 39

Climate Controls

• To improve the A/C cool down, drive with the windows slightly open

for 2–3 minutes after start up or until the vehicle has been “aired out.”

For maximum cooling performance in AUTO mode:

• Press AUTO control and set to desired temperature.

For maximum cooling performance using manual override modes:

• Press

60°F (16°C) and the fan to the highest setting.

To aid in side window defogging and demisting in cold weather:

1. Select

2. Select A/C.

3. Set the temperature control to maintain comfort.

4. Set the fan speed to highest setting.

5. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.

To increase airflow to the outer instrument panel vents, close the vents located in the middle of the instrument panel.

(panel), A/C, with recirculated air. Set the temperature to

Do not place objects on top of the instrument panel as these objects may become projectiles in a collision or sudden stop.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 40

Lights

HEADLAMP CONTROL

Turns the lamps off.

Turns on the parking lamps, instrument panel lamps, license plate lamps and tail lamps.

Turns the headlamps on.

Autolamp control (if equipped)

The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control.

The autolamp system also keeps the lights on for approximately 20 seconds after the ignition switch is turned to OFF.

To change the delay time of the autolamp feature, do the following:

1. Start with the ignition in OFF and the autolamps selected.

2. Deselect the autolamps.

3. Put the ignition in RUN.

4. Put the ignition in OFF.

5. Select the autolamps. Steps 2 through 5 must be performed within a 10 second period. At this point, the headlamps and parking lamps will turn on.

6. Deselect the autolamps after the desired autolamp delay time (maximum of 3 minutes). At this point, the headlamps and parking lamps will turn off.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 41

Lights

Foglamp control (if equipped)

The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp

control is in the position and the high beams are not

turned on.

In autolamp mode, the foglamps won’t be operational until lighting conditions warrant the activation of the headlamp/parklamp lighting.

Pull headlamp control towards you to turn foglamps on. The foglamp indicator light parklamps are on.

Daytime running lamps (DRL) (if equipped)

Turns the headlamps on with a reduced output.

To activate:

• the ignition must be in the ON position,

• the headlamp control is in the OFF or parking lamp position and

• the parking brake must be disengaged.

Always remember to turn on your headlamps at dusk or during

inclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provide adequate lighting during these conditions. Failure to activate your headlamps under these conditions may result in a collision.

, or

will illuminate when the switch is pulled and the

High beams

Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 42

Lights

Flash to pass

Pull toward you slightly to activate and release to deactivate.

PANEL DIMMER CONTROL

Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation.

Move the control to the full upright position, past detent, to turn on the interior lamps.

AIMING THE HEADLAMPS

Your vehicle may be equipped with a sealed beam or aerodynamic headlamp system. Sealed beam headlamps may be aimed in the vertical (up/down) and the horizontal (left/right) directions using the procedures following. The aerodynamic headlamps can only be aimed in the vertical direction (up/down) using the procedures following. The headlamps on your vehicle are properly aimed at the assembly plant and should not normally need adjusting.

Vertical and horizontal aim adjustment (sealed beam headlamps)

The headlamps on your vehicle are intended to be aimed using mechanical aimers. If mechanical aimers are utilized, and a universal headlamp adaptor is not available (in other words only the base, non-adjustable 6x8 sealed beam adaptor is available) and the cross-car sight line is in any way blocked, Ford Motor Company will supply a pair of spacer blocks at no cost. Please contact your dealer. If a universal adaptor is available and the cross-car sight line is in any way blocked, set the legs of the universal adaptor all to the same setting, such that the cross-car sight line is no longer blocked, per the instructions for the brand of mechanical aimer employed. You can also aim the headlamps visually using the procedure set forth below.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 43

Lights

To adjust the headlamps:

1. Park your vehicle on a level surface about 25 feet (7.6 meters) away from a vertical plain surface (3). Check your headlamp alignment at night or in a dark area so that you can see the headlamp beam pattern.

• (1) Eight feet

• (2) Center height of lamp to

ground

• (3) Twenty-five feet

• (4) Horizontal reference line

• (5) Center of headlamps

• (6) Center line of the vehicle

2. The center of the headlamp is marked either on the lens (a circle or cross marker) or on the bulb shield, internal to the lamp (mark or feature). Measure the height from the center of your headlamp to the ground (2) and mark an 8 foot (2.4 meter) long horizontal line on the wall or screen (1) at this height (masking tape works well).

3. Turn on the low beam headlamps and open the hood.

4. Locate the high intensity area of the beam pattern and place the top edge of the intensity zone even with the horizontal reference line (4). If the top edge of the high intensity area is not even with the horizontal line, follow the next step to adjust it.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 44

Lights

5. Locate the vertical adjuster (2) for each headlamp. Adjust the aim by turning the adjuster control either clockwise (to adjust up) or counterclockwise (to adjust down).

6. In addition to the horizontal line marked in step 2, a pair of vertical lines (5) must be marked at the center line of the headlamps on the wall or screen.

7. On the wall or screen, locate the high intensity area of the beam pattern. The left edge of the high intensity area should be even with the vertical line corresponding to the headlamp under adjustment. If the left edge of the high intensity area is not even with the vertical line, follow the next step to adjust it.

8. Locate the horizontal adjuster (1) for each headlamp. Turn it clockwise or counterclockwise, to place the left edge of the high intensity area even with the vertical line corresponding to the headlamp under adjustment.

Vertical aim adjustment (aerodynamic headlamps)

The headlamps on your vehicle can only be vertically adjusted. Your vehicle does not require horizontal aim adjustments.

To adjust the headlamps:

1. Park the vehicle directly in front of a wall or screen on a level surface, approximately 25 feet (7.6 meters) away.

• (1) Eight feet

• (2) Center height of lamp to ground

• (3) Twenty-five feet

• (4) Horizontal reference line

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 45

Lights

2. Measure the height from the center of your headlamp (indicated by a 3.0 mm circle on the lens) to the ground and mark an 8 foot (2.4 meter) horizontal reference line on the vertical wall or screen at this height (a piece of masking tape works well).

3. Turn on the low beam headlamps to illuminate the wall or screen and open the hood. Cover one of the headlamps so no light hits the wall.

4. On the wall or screen you will observe a light pattern with a distinct horizontal edge towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted so the edge is at the same height as the horizontal reference line.

5. Locate the vertical adjuster on each headlamp, then use a E5 Torx socket to turn the adjuster either counterclockwise (to adjust down) or clockwise (to adjust up) aligning the upper edge of the light pattern up to the horizontal line.

6. Repeat step 3–5 for the other headlamp.

7. Close the hood and turn off the lamps.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 46

Lights

TURN SIGNAL CONTROL

• Push down to activate the left turn signal.

• Push up to activate the right turn signal.

COURTESY/READING LAMPS (IF EQUIPPED)

The dome lamp lights when any door is not completely closed, the instrument panel switch is pushed past the detent and when any of the remote entry controls are pressed while the ignition is off.

The reading lamps can be turned on by pressing the rocker controls next to each lamp.

MAP LAMPS (IF EQUIPPED)

To turn on the map lamps, press the control next to each lamp.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 47

BULBS

Replacing exterior bulbs

Check the operation of all the bulbs frequently.

Lights

Function Number of

bulbs

Headlamps (aerodynamic) 2 9008 Headlamps (sealed beam) 2 H6054 Park lamp with

aerodynamic headlamp Park lamp with sealed

beam headlamp Sidemarker 2 194 Tail/stop/turn/sidemarker 2 4157K/3157 Backup 2 3156 High-mount stoplamp 1 922 Foglamp 2 9145 License plate lamp 2 194 Cargo lamp 2 906 Roofmarker 5 194 Rear fender clearance* 4 W5W Interior visor lamp (if

equipped) Rear identification 3 194 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer * Dual rear wheels, or if equipped.

2 3157A

2 4157K/3157

4 194

Trade number

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 48

Lights

Replacing headlamp bulbs (aerodynamic)

1. Make sure that the headlamp control is in the OFF position and open

the hood.

2. Remove the four screws from the

top and bottom front of the headlamp assembly.

3. Press the retaining clip at the top

of the headlamp assembly while pulling the assembly straight out.

If removing the lamp is difficult, removing the four screws along the top of the grill will help provide more clearance.

4. Disconnect the electrical

connector by squeezing the release tab and pushing the connector forward and then pulling it reward.

5. Remove the bulb assembly by

turning it counterclockwise and pulling it straight out.

Handle a halogen headlamp bulb carefully and keep out of

children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.

Install the new bulb(s) in reverse order.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 49

Lights

Replacing park/turn and sidemarker lamp bulbs (aerodynamic)

1. Make sure that the headlamp control is in the OFF position and open the hood.

2. Remove the four screws from the top and bottom front of the headlamp assembly.

3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out.

If removing the lamp is difficult, removing the four screws along the top of the grill will help provide more clearance.

4. Remove the bulb assembly, (1) sidemarker or (2) park/turn by turning it counterclockwise and pulling it straight out.

5. Pull the old bulb out from the socket.

Install the new bulb(s) in reverse order.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 50

Lights

Replacing headlamp bulbs (sealed beam)

1. Make sure that the headlamp control is in the OFF position and open the hood.

2. Remove the four screws from the top and bottom front of the headlamp assembly.

3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out.

If removing the lamp is difficult, removing the four screws along the top of the grill will help provide more clearance.

4. Disconnect the electrical connector from the park lamp/bezel.

5. Remove the four screws and the headlamp retaining ring from headlamp.

Install the new bulb(s) in reverse order.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 51

Lights

Replacing park/turn/sidemarker bulbs (sealed beam)

1. Make sure that the headlamp control is in the OFF position and open the hood.

2. Remove the four screws from the top and bottom front of the headlamp assembly.

3. Press the retaining clip at the top of the headlamp assembly while pulling the assembly straight out.

If removing the lamp is difficult, removing the four screws along the top of the grill will help provide more clearance.

4. Remove the bulb assembly, (1) sidemarker or (2), park/turn by turning it counterclockwise.

5. Pull the old bulb out from the socket.

Install the new bulb(s) in reverse order.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 52

Lights

Replacing tail lamp/turn/backup lamp bulbs — F250/F350 only

1. Make sure the headlamp switch is in the OFF position and then open the tailgate to expose the lamp assemblies.

2. Remove the two bolts from the tail lamp assembly and carefully pull the lamp assembly from the tailgate pillar by releasing the two retaining tabs.

3. Rotate the bulb socket counterclockwise and remove from lamp assembly.

4. Pull the bulb straight out of the socket.

Install the new bulb(s) in reverse order.

Replacing brake/tail/backup lamp bulbs — F450/F550 only

1. Make sure the headlamp switch is in the OFF position.

2. Remove the four screws and the lamp lens from lamp assembly.

3. Carefully pull the bulb straight out of the socket and push in the new bulb.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 53

Replacing cargo lamp and high-mount brakelamp bulbs

1. Make sure the headlamp switch is in the OFF position.

2. Remove the two screws and lamp assembly from vehicle as wiring permits.

3. Remove the bulb socket by rotating counterclockwise.

4. Pull the bulb straight out of the socket.

Replacing roof marker bulbs

1. Make sure the headlamp switch is in the OFF position.

2. Remove the screw and lens from the lamp assembly.

3. Pull the bulb straight out of the socket.

Lights

Install the bulb(s) in reverse order.

Replacing foglamp bulbs (if equipped)

1. Make sure the headlamp switch is in the OFF position.

2. Remove the bulb socket from the foglamp by turning counterclockwise.

3. Disconnect the electrical connector from the foglamp bulb.

Install the new bulb(s) in reverse order.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 54

Lights

Replacing license plate lamp bulbs

The license plate bulbs are located behind the rear bumper. To change the license plate lamp bulbs:

1. Reach behind the rear bumper to locate the bulb.

2. Twist the bulb socket counterclockwise and carefully pull to remove it from the lamp assembly.

3. Pull out the old bulb from the socket and push in the new bulb.

4. Install the bulb socket in lamp assembly by turning it clockwise.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 55

Driver Controls

MULTI-FUNCTION LEVER

Windshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers.

Windshield washer: Push the end of the stalk:

• briefly: causes a single swipe of the wipers without washer fluid.

• a quick push and hold: the wipers will swipe three times with washer fluid.

• a long push and hold: the wipers and washer fluid will be activated for up to ten seconds.

Driver Controls

Changing the wiper blades

1. Pull the wiper arm away from the

vehicle. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.

2. Attach the new wiper to the

wiper arm and press it into place until a click is heard.

3. Replace wiper blades every 6 months for optimum performance.

4. Poor wiper quality can sometimes be improved by cleaning the wiper

blades, refer to Window and wiper blades in the Cleaning chapter.

5. To prolong the life of the wiper blades, it is highly recommended to

scrape off the ice on the windshield before turning on the wipers. The layer of ice has many sharp edges and can damage the micro edge of the wiper rubber element.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 56

Driver Controls

TILT STEERING WHEEL (IF EQUIPPED)

To adjust the steering wheel:

1. Pull and hold the steering wheel

release control toward you.

2. Move the steering wheel up or

down until you find the desired location.

3. Release the steering wheel

release control. This will lock the steering wheel in position.

Never adjust the steering wheel when the vehicle is moving.

TRANSMISSION CONTROL

Tow/Haul feature

(5–speed automatic transmission) (if equipped)

To activate, press the transmission control switch (TCS) located on the gearshift. The TOW/HAUL indicator light will illuminate in the instrument cluster. The transmission will operate in all gears. Press the transmission control switch again to deactivate Tow/Haul mode. When you shut off and re-start your vehicle, the transmission will automatically return to normal mode with Tow/Haul feature deactivated, refer to the Driving chapter for more information.

ILLUMINATED VISOR MIRROR (IF EQUIPPED)

Lift the mirror cover to turn on the visor mirror lamps.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 57

Driver Controls

OVERHEAD CONSOLE (IF EQUIPPED)

The appearance of your vehicle’s overhead console will vary according to your option package.

Storage compartment (if equipped)

Press the release on the door to open the storage compartment.

The storage compartment may be used to secure sunglasses or a similar object and the front tab can be used for holding tickets, paper, envelopes, etc. The front bin may be used to store small objects.

One-touch moon roof (if equipped)

The moon roof control is located on the overhead console.

Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt themselves.

Note: The moon roof will open to the “comfort” position first before opening all the way. The “comfort” position helps to alleviate rumbling wind noise which may happen in the vehicle with the roof fully opened.

To open the moon roof: The moon roof is equipped with a one-touch open feature. Press and release the AUTO control. The moon roof will open to the “comfort” position. Press and release the control again to fully open. To stop the one-touch open feature press either the AUTO or

To close the moon roof: Press and hold the control until the glass panel stops at the “comfort” position. Press and hold the control again until the glass stops moving. When fully closed, the rear portion of the glass panel will appear higher than the front portion.

control again.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 58

Driver Controls

To vent the moon roof: Press and hold the control. The moon roof must be in the closed position in order to move it into the

vent position. To close, press and hold the AUTO control until the glass

panel stops moving.

The moon roof has a built-in sliding shade that can be manually opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle.

When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are not in the

proximity of the moon roof opening.

AUXILIARY POWER POINT (12VDC)

Power outlets are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty.

The auxiliary power point is located on the instrument panel.

Do not plug optional electrical accessories into the cigarette lighter. Use the power point.

Do not use the power point for operating the cigarette lighter element.

The Maximum power each power point can supply depends on the fuse rating. For example: a 20A fuse should supply a maximum of 240 Watts, a 15A fuse should supply a maximum of 180 Watts and a 10A fuse should supply a maximum of 120 Watts. Exceeding these limits will result in a blown fuse.

Always keep the power point caps closed when not being used.

POWER WINDOWS (IF EQUIPPED)

Do not leave children unattended in the vehicle and do not let children play with the power windows. They may seriously injure

themselves.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 59

When closing the power windows, you should verify they are free of obstructions and ensure that children and/or pets are not in

the proximity of the window openings.

Press and hold the bottom part of the rocker switch to open the window. Press and hold the top part of the rocker switch to close the window.

One touch down

Allows the driver’s window to open fully without holding the control down. Press completely down on AUTO and release quickly. Press again to stop.

Window lock (if equipped)

The window lock feature allows only the driver to operate the power windows.

To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls.

Driver Controls

Power rear slider window (if equipped)

• Press and hold the open arrow side of control to open window.

• Press and hold the closed arrow side of control to close window.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 60

Driver Controls

Accessory delay (if equipped)

With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until any door is opened.

MIRRORS

Automatic dimming inside rear view mirror (if equipped)

Your vehicle is equipped with an inside rear view mirror with an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror. When the mirror detects bright light from front or behind, it will automatically adjust to minimize glare.

Press the control located on the bottom of the mirror to turn the mirror on or off. The mirror will automatically return to the normal state whenever the vehicle is placed in R (reverse)(when the mirror is on) to ensure a bright clear view when backing up.

Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.

Power side view mirrors (if equipped)

To adjust your mirrors:

1. Select L to adjust the left mirror

or R to adjust the right mirror.

2. Move the control in the direction

you wish to tilt the mirror.

3. Return to the center position to

disable the adjust function.

Heated outside mirrors

The main mirror glass is heated automatically to remove ice, mist and fog and activates when the vehicle is started.

Note: The mirrors may be hot to the touch but will not burn. This is a normal condition.

(if equipped)

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 61

Driver Controls

Type A

The mirror heating elements are designed to operate regardless of the geographic location of the vehicle. There is no switch to turn on, or other operator involvement required other than to start the vehicle.

Type B

The spotter mirror, below the main mirror, is not heated and must be adjusted manually.

Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors.

Mirror mounted side turn signal indicator (if equipped)

When the vehicle turn signals are activated, the outer portion of the mirror housing will blink amber.

The turn signal feature can be seen by other drivers who may approach from the rear of the vehicle.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 62

Driver Controls

Clearance lamps (if equipped)

Illuminates when the headlamps or parking lamps are switched on.

This provides additional visibility of your vehicle to other drivers on the road.

Fold-away mirrors

The mirrors can be manually folded forward or backwards for narrow spaces like driving through an automatic car wash or backing out of a garage with the trailer tow mirror.

The telescoping feature (if equipped) allows the mirror to extend approximately 3.15 inches (80 mm). This feature is especially useful to the driver when towing a trailer.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 63

Driver Controls

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED)

The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position.

Press and hold the rocker control to adjust accelerator and brake pedal toward you or away from you.

The adjustment allows for approximately 2.75 inches (70 mm) of maximum travel.

Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.

SPEED CONTROL (IF EQUIPPED)

With speed control set, you can maintain a speed of 30 mph (48 km/h) or more without keeping your foot on the accelerator pedal. Speed control does not work at speeds below 30 mph (48 km/h).

Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.

Setting speed control

The controls for using your speed control are located on the steering wheel for your convenience.

1. Press the ON control and release

it.

2. Accelerate to the desired speed.

OFF

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 64

Driver Controls

3. Press the SET ACCEL control

and release it.

4. Take your foot off the accelerator

pedal.

5. The indicator

light on the

instrument cluster will turn on.

Note:

• Vehicle speed may vary momentarily when driving up and down a steep hill.

• If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce the speed.

• If the vehicle speed decreases more than 10 mph (16 km/h) below your set speed on an uphill, your speed control will disengage.

Resuming a set speed

Press the RES/RESUME control and release it. This will automatically return the vehicle to the previously set speed. The RES/RESUME control will not work if the vehicle speed is not faster than 30 mph (48 km/h).

RES

ACCEL

COAST

RES

SET

ACCEL

COAST

SET

Increasing speed while using speed control

There are two ways to set a higher speed:

• Press and hold the SET ACCEL control until you get to the desired speed, then release the control. You can also use the SET

RES

SET

ACCEL

COAST

ACCEL control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET ACCEL control.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 65

Driver Controls

Reducing speed while using speed control

There are two ways to reduce a set speed:

• Press and hold the COAST control until you get to the desired speed, then release the control. You can also use the COAST control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).

• Depress the brake pedal until the desired vehicle speed is reached, press the SET ACCEL control.

Turning off speed control

There are two ways to turn off the speed control:

• Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed.

• Press the speed control OFF control.

Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.

RES

ACCEL

COAST

RES

SET

ACCEL

COAST

OFF

SET

Indicator light (if equipped)

This light comes on when either the SET ACCEL or RES controls are pressed. The vehicle speed must be at or above 48 km/h (30 mph). It turns off when the speed control OFF control is pressed, the brake or clutch is applied, or the ignition is turned to the OFF position.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 66

Driver Controls

STEERING WHEEL CONTROLS (IF EQUIPPED)

These controls allow you to operate some radio and climate control features.

Radio control features

• Press MODE to select AM, FM1, FM2, TAPE or CD (if equipped).

In Radio mode:

• Press NEXT to seek/scan to the next strong station.

In Tape mode:

• Press NEXT to listen to the next selection on the tape.

In CD mode:

• Press NEXT to listen to the next track on the disc.

In any mode:

• Press VOL up or down to adjust the volume.

Climate control features

• Press TEMP up or down to adjust temperature.

• Press FAN up or down to adjust fan speed.

MODE

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 67

Driver Controls

CENTER CONSOLE (IF EQUIPPED)

Your vehicle may be equipped with a variety of console features. These include:

• Utility compartment with cassette/CD holder

• Coin holder

• Pen holder

• Writing surface

Use only soft cups in the cupholder. Hard objects can

injure you in a collision.

CELL PHONE USE

The use of Mobile Communications Equipment has become increasingly important in the conduct of business and personal affairs. However, drivers must not compromise their own or others’ safety when using such equipment. Mobile Communications can enhance personal safety and security when appropriately used, particularly in emergency situations. Safety must be paramount when using mobile communications equipment to avoid negating these benefits.

Mobile Communication Equipment includes, but is not limited to cellular phones, pagers, portable email devices, in vehicle communications systems, telematics devices and portable two-way radios.

A driver’s first responsibility is the safe operation of the vehicle.

The most important thing you can do to prevent a crash is to avoid distractions and pay attention to the road. Wait until it is safe to operate Mobile Communications Equipment.

MINI MESSAGE CENTER (IF EQUIPPED)

With the ignition in the ON position, the mini message center, located on your instrument cluster, displays text messages that alert you to possible problems or malfunctions in your vehicle’s operating systems.

Note: The following warning messages will reappear after an ignition OFF-ON cycle has been completed.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 68

Driver Controls

Door ajar: Displays when the ignition is in the ON position and any door is open.

Check fuel cap: Displays when the fuel cap may not be properly installed. Continued driving with this display on may cause the Service engine soon warning light to come on. Refer to Fuel filler cap under the Fuel Information section in the Maintenance and Specifications chapter.

Trailer fault (if equipped):

Displayed if there is a short circuit on the electric brake output wire or the trailer brakes are drawing too much current. Refer to Integrated trailer brake controller in the Tires, Wheels and Loading chapter for more information.

TBC fault (if equipped): Displays in response to faults sensed by the TBC. In the event this message is seen, please take your vehicle to an authorized Ford dealership for diagnosis and repair. Refer to Integrated trailer brake controller in the Tires, Wheels and Loading chapter for more information.

Note: The following warning messages will reappear on the display every ten minutes.

Low fuel: Displays when the fuel level in the fuel tank is at or near empty (refer to Fuel gauge in this chapter).

Check gauge: Displays when any of the following conditions has occurred:

• The engine coolant temperature is high.

• The engine oil pressure is low.

• The fuel gauge is at or near empty.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 69

Driver Controls

Check trailer (if equipped):

Displayed when a trailer connection becomes disconnected, either intentionally or unintentionally, and has been sensed during a given ignition cycle. Refer to Integrated trailer brake controller in the Tires, Wheels and Loading chapter for more information.

Language

The language options are English and French. The feature works as follows:

1. If present language is English,

press and hold the SELECT/RESET button for 15 seconds or greater to convert the language selection to French. The word ⬙FRENCH⬙ will be displayed for 4 seconds as a confirmation that language has been changed.

2. If present language is French,

press and hold the SELECT/RESET button for 15 seconds or greater to convert the language selection to English. The word ⬙ENGLISH⬙ will be displayed for 4 seconds as a confirmation that language has been changed.

MESSAGE CENTER (IF EQUIPPED)

With the ignition in the ON position, the message center, located on your instrument cluster, displays important vehicle information

through a constant monitor of vehicle systems. You may select

display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 70

Driver Controls

Selectable features

Reset

Press this control to select and reset functions shown in the INFO menu and SETUP menu.

Info menu

This control displays the following control displays:

• Odometer/Compass

• Trip odometer/Odometer/Compass

• Distance to

Empty/Odometer/Compass

• Average Fuel Economy/Odometer/Compass

• Engine hour meter/Odometer/Compass

Odometer/Trip odometer

Refer to Gauges in the Instrument Cluster chapter.

Compass display

The compass heading is displayed as one of N, NE, E, SE, S, SW, W and NW in the message center display.

The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy.

Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions. If the compass still appears to be inaccurate, a manual calibration may be necessary. Refer to Compass zone/calibration

adjustment.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 71

Driver Controls

Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone/calibration adjustment.

Compass zone/calibration adjustment

1. Determine your magnetic zone by

referring to the zone map.

2. Turn ignition to the ON position.

3. Start the engine.

4. From Info menu, press and hold

the SETUP and RESET controls simultaneously until the message center display changes to show the current zone setting (XX).

5. Press the SETUP control

repeatedly until the correct zone setting for your geographic location is displayed on the message center. The range of zone values are from 01 to 15 and “wraps” back to 01.

6. To exit the zone setting mode,

and to “lock in” your change, press and release the RESET control.

123

6 7 8 9 1011

14 13

Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 72

Driver Controls

7. Press the RESET control to start

the compass calibration function.

8. Slowly drive the vehicle in a

circle (less than 3 mph [5 km/h]) until the CIRCLE SLOWLY TO CALIBRATE display changes to CALIBRATION COMPLETED. It will take up to five circles to complete calibration.

9. The compass is now calibrated.

Distance to empty (DTE)

Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel.

The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes.

DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is reinitialized to a factory default value if the battery is disconnected.

Average fuel economy (AFE)

Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/ 100 km.

If you calculate your average fuel economy by dividing gallons of fuel used by 100 miles traveled (kilometers traveled by liters used), your figure may be different than displayed for the following reasons:

• Your vehicle was not perfectly level during fill-up

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 73

Driver Controls

• Differences in the automatic shut-off points on the fuel pumps at service stations

• Variations in top-off procedure from one fill-up to another

• Rounding of the displayed values to the nearest 0.1 gallon (liter)

1. Drive the vehicle at least 5 miles (8 km) with the speed control

system engaged to display a stabilized average.

2. Record the highway fuel economy for future reference.

It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings.

Engine hour meter

Select this function from the INFO menu to display the accumulated running time of the engine.

Setup menu

Press this control for the following displays:

• System Check

• Units (English/Metric)

• Autolock

• Autolamp Delay

• Language

System check

Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds.

Pressing the RESET control cycles the message center through each of the systems being monitored.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 74

Driver Controls

The sequence of the system check report and how it appears in the message center is as follows:

1. ENGINE TEMP

2. TRANS TEMP

3. OIL PRESSURE

4. BRAKE FLUID LEVEL

5. DOOR AJAR

6. FUEL CAP

7. AIR FILTER (diesel only)

8. FUEL LEVEL

Units (English/Metric)

1. Select this function from the

SETUP menu for the current units to be displayed.

2. Press the RESET control to

change from English to Metric.

Autolocks

This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion.

1. To disable/enable the autolock

feature, select this function from the SETUP control for the current display mode.

2. Press the RESET control to turn

the autolocks ON or OFF.

Autolamp delay

This feature keeps your headlights on for up to three minutes after the ignition is switched off.

1. To disable/enable the autolamp

delay feature, select this function from the SETUP control for the current display mode.

2. Press the RESET control to select

the new Autolamp delay values of >0, >10, >20, >30, >60, >90, >120 or >180.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 75

Driver Controls

Language

1. Select this function from the

SETUP menu for the current language to be displayed.

2. Pressing the RESET control

cycles the message center through each of the language choices.

3. Press and hold the RESET

control to set the language choice.

System warnings

System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems.

In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds.

The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message.

Warning messages that have been reset are divided into three categories:

• They will not disappear until a condition is changed.

• They will reappear on the display ten minutes from the reset.

• They will not reappear until an ignition OFF-ON cycle has been

completed.

This acts as a reminder that these warning conditions still exist within the vehicle.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 76

Driver Controls

Warning display Status

Reduced engine power Warning cannot be reset Stop engine safely Low fuel level Warning returns after 10 minutes Low brake fluid level Low oil pressure Check engine temperature Trailer disconnected Water in fuel (diesel only) Check air filter (diesel only) Door ajar Warning returns after the ignition key Check fuel cap Engine failsafe mode Check compass module Trailer fault TBC fault

DOOR AJAR. Displayed when a door is not completely closed. CHECK ENGINE TEMPERATURE. Displayed when the engine

coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool. Check the coolant and coolant level. Refer to Engine coolant in the Maintenance and Specifications chapter. If the warning stays on or continues to come on, contact your dealer as soon as possible.

REDUCED ENGINE POWER. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on followed by an indicator chime or continues to come on, contact your dealer as soon as possible.

STOP ENGINE SAFELY. Displayed when the engine is overheating. Stop the vehicle as soon as safely possible, turn off the engine. If the warning stays on followed by an indicator chime or continues to come on, contact your dealer as soon as possible.

LOW FUEL LEVEL. Displayed as an early reminder of a low fuel condition.

LOW BRAKE FLUID LEVEL. Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Checking and adding brake fluid in the Maintenance and Specifications chapter.

is turned from OFF to ON.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 77

Driver Controls

LOW OIL PRESSURE. Displayed when the engine oil pressure is low. If this warning message is displayed, check the level of the engine oil. Refer to Engine oil in the Maintenance and Specifications chapter for information about adding engine oil. If the oil level is OK and this warning persists, shut down the engine immediately and contact your dealership for service.

CHECK FUEL CAP. Displayed when the fuel filler cap is not properly installed. Check the fuel filler cap for proper installation. Refer to Fuel

filler cap under the Fuel Information section in the Maintenance and Specifications chapter.

ENGINE FAILSAFE MODE. Displayed when the engine has defaulted to a ’limp-home’ operation. If the warning stays on or continues to come on, contact your dealer as soon as possible.

CHECK COMPASS MODULE. Displayed when the compass is not operating properly. If the warning stays on or continues to come on, contact your dealer as soon as possible.

TRAILER DISCONNECTED (if equipped): Displayed when a trailer connection becomes disconnected, either intentionally or unintentionally, and has been sensed during a given ignition cycle. Refer to Intergrated trailer brake controller in the Tires, Wheels and Loading chapter for more information.

TRAILER FAULT (if equipped): Displayed if there is a short circuit on the electric brake output wire or the trailer brakes are drawing too much current. Refer to Intergrated trailer brake controller in the Tires, Wheels and Loading chapter for more information.

TBC FAULT (if equipped): Displayed in response to faults sensed by the TBC. In the event this message is seen, please take your vehicle to an authorized Ford dealership for diagnosis and repair. Refer to Intergrated trailer brake controller in the Tires, Wheels and Loading chapter for more information.

WATER IN FUEL (diesel only): Refer to Instrumentation in your 6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement.

CHECK AIR FILTER (diesel only): Refer to Instrumentation in your

6.0 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide

Supplement.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 78

Driver Controls

DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules.

• Odometer

• Fuel flow

• Fuel level

• Trans temp

• Fuel cap

• Engine sensor

• Brake fluid

• Auto lock

• Auto lamp delay

Contact your dealer as soon as possible if these messages occur on a regular basis.

TAILGATE LOCK (IF EQUIPPED)

Your vehicle may be equipped with a tailgate lock designed to prevent theft of the tailgate.

• Insert ignition key and turn to the right to engage lock.

• Turn ignition key to the left to unlock.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 79

Driver Controls

Tailgate removal

Your tailgate is removable to allow more room for loading.

1. Lower the tailgate.

2. Use a screwdriver to pry the

spring clip (on each connector) past the head of the support screw. Disconnect cable.

3. Disconnect the other cable.

4. Lift tailgate to a 45 degree angle.

5. Lift right side off of its hinge.

6. Lift left side off of its hinge.

To install, follow the removal procedures in reverse order.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 80

Locks and Security

KEYS

The key operates all locks on your vehicle. You should always carry a second key with you in a safe place in case you require it in an emergency.

Your keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your dealer supplied keys, replacement keys are available through your authorized dealer.

POWER DOOR LOCKS (IF EQUIPPED)

Press control to unlock all doors.

Press control to lock all doors.

Smart locks (if equipped)

This feature prevents you from locking yourself out of the vehicle if your key is still in the ignition.

When you open the driver’s door and you lock the vehicle with the power door lock control, all the doors will lock, then the driver’s door will automatically unlock reminding you that your key is still in the ignition.

The vehicle can still be locked, with the key in the ignition, using the manual lock button on the door, locking the driver’s door with a key, by simultaneously pressing button 7 • 8 and the 9 • 0 controls on the remote entry keypad (if equipped), or using the lock button on the remote entry transmitter (if equipped).

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 81

Locks and Security

Childproof door locks (if equipped)

• When these locks are set, the rear doors cannot be opened from the inside.

• The rear doors can be opened from the outside when the doors are unlocked.

The childproof locks are located on rear edge of each rear door and must be set separately for each door. Setting the lock for one door will not automatically set the lock for both doors.

• Move lock control up to engage the childproof lock.

• Move lock control down to disengage the childproof lock.

REMOTE ENTRY SYSTEM (IF EQUIPPED)

This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

The typical operating range for your remote entry transmitter is approximately 33 feet (10 meters). A decrease in operating range could be caused by:

• weather conditions,

• nearby radio towers,

• structures around the vehicle, or

• other vehicles parked next to your vehicle.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 82

Locks and Security

Your vehicle is equipped with a remote entry system which allows you to:

• unlock the vehicle doors without a key.

• lock all the vehicle doors without a key.

• activate the personal alarm.

If there is any potential remote keyless entry problem with your vehicle, ensure ALL remote entry transmitters are taken to the dealership, to aid in troubleshooting.

Unlocking the doors

1. Press and release to unlock the driver’s door. Note: The interior

lamps will illuminate.

2. Press

doors.

Locking the doors

1. Press and release to lock all the doors. The parking lamps will flash

if all the doors are closed and locked.

2. Press

doors are closed and locked. Note: The doors will lock again, the horn will chirp once, and the parking lamps will flash once more.

If any of the doors are not properly closed the horn will make two quick chirps.

and release again within three seconds to unlock all the

and release again within three seconds to confirm that all the

Power door lock disable feature (if equipped)

The UNLOCK inside the vehicle when:

• the ignition has been turned to the 3 (OFF) position, and

• 20 seconds elapse after all vehicle doors are closed and locked using

the remote entry transmitter, or the power door lock control (while the accompanying door is open).

feature on your power door locks will not work from

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 83

Locks and Security

The UNLOCK feature will work again after:

• a door has become ajar,

• the ignition is turned to the 4 (ON) position,

• unlocking the vehicle using the keyless entry keypad,

• or using the UNLOCK

equipped).

This feature is initially deactivated, but may be activated by taking your vehicle to an authorized Ford dealer.

Sounding a panic alarm

Press (ON) to deactivate.

Note: The panic alarm will only operate when the ignition is in the 2 (LOCK) or 3 (OFF) position.

Replacing the battery

The remote entry transmitter uses one coin type three-volt lithium battery CR2032 or equivalent.

To replace the battery:

1. Twist a thin coin between the two

halves of the remote entry transmitter near the key ring. DO NOT TAKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER.

to activate the alarm. Press again or turn the ignition to 4

control on your remote entry transmitter (if

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 84

Locks and Security

2. Do not wipe off any grease on the

battery terminals on the back surface of the circuit board.

3. Remove the old battery. Note: Please refer to local regulations when

disposing of transmitter batteries.

4. Insert the new battery. Refer to the diagram inside the remote entry

transmitter for the correct orientation of the battery. Press the battery down to ensure that the battery is fully seated in the battery housing cavity.

5. Snap the two halves back together.

Note: Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter should operate normally after battery replacement.

Replacing lost remote entry transmitters

If you would like to have your remote entry transmitter reprogrammed because you lost one, or would like to buy additional remote entry transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming.

How to reprogram your remote entry transmitters

You must have all remote keyless entry keypads and remote entry transmitters (maximum of four) available before beginning this

procedure.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 85

Locks and Security

To program the keyless entry keypads remote entry transmitters yourself:

1. Ensure the vehicle is

electronically unlocked.

2. Put the key in the ignition.

3. Turn the key from the 2 (LOCK)

position to 3 (OFF).

4. Cycle eight times rapidly (within

10 seconds) between the 3 (OFF) position and 4 (ON). Note: The eighth turn must end in the 4 (ON) position.

5. The doors will lock, then unlock, to confirm that the programming

mode has been activated.

6. Within 20 seconds, program the keyless entry keypad by pressing the

7 • 8 and the 9 • 0 controls at the same time.

7. The doors will lock, then unlock, to confirm that the keypad

programming mode has been activated.

8. Within 20 seconds, program the remote entry transmitter by pressing

any button on the transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again.

9. The doors will again lock, then unlock, to confirm that this remote

entry transmitter has been programmed.

10. Repeat Step 8 to program each additional remote keypad or entry

transmitter.

11. Turn the ignition to the 3 (OFF) position after you have finished

programming all of the remote entry transmitters. Note: If more than 20 seconds have passed you will need to start the procedure over again.

12. The doors will once again lock, then unlock, to confirm that the

programming mode has been exited.

Illuminated entry

The interior lamps illuminate when the remote entry system is used to unlock the door(s).

The illuminated entry system will turn off the interior lights if:

• the ignition switch is turned to the 4 (ON) position, or

• the remote transmitter lock control is pressed, or

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 86

Locks and Security

• the 7 • 8 and the 9 • 0 controls on the keyless entry keypad are pressed, or

• after 25 seconds of illumination.

The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate.

The inside lights will not turn off if:

• they have been turned on with the dimmer control, or

• any door is open.

The battery saver will shut off the interior lamps 30 minutes after the ignition has been turned to the 3 (OFF) position, 10 minutes after if the dome lamp is off, and 30 minutes after if the dome lamp switch is left on.

KEYLESS ENTRY SYSTEM

You can use the keyless entry keypad to lock or unlock the doors without using a key.

The keypad can be operated with the factory set 5–digit entry code; this code is located on the owner’s wallet card in the glove box, is marked on the computer module, and is available from your authorized dealer. You can also create your own 5–digit personal entry code.

When pressing the controls on the keypad, press the middle of the controls to ensure a good activation.

Programming a personal entry code

To create your own personal entry code:

1. Enter the factory set code.

2. Within five seconds press the 1 • 2 on the keypad.

3. Enter your personal 5-digit code. Each number must be entered

within five seconds of each other.

4. The doors will again lock then unlock to confirm that your personal

keycode has been programmed to the module.

Tips:

• Do not set a code that uses five of the same number.

• Do not use five numbers in sequential order.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 87

Locks and Security

• The factory set code will work even if you have set your own personal code.

• If you set a second personal code it will erase your first personal code.

Erasing personal code

1. Enter the factory set 5–digit code.

2. Within five seconds, press the 1 • 2 on the keypad and release.

3. Press and hold the 1 • 2 for two seconds. This must be done within

five seconds of completing Step 2.

Your personal code is now erased and only the factory set 5–digit code will work.

Anti-scan feature

If an incorrect code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables the keypad for one minute and the keypad lamp will flash during this time.

The anti-scan feature will turn off after:

• one minute of keypad inactivity.

• pressing the

• the ignition is turned to the 4 (ON) position.

Unlocking and locking the doors using keyless entry

To unlock the driver’s door, enter the factory set 5-digit code or your personal code. Each number must be pressed within five seconds of each other. The interior lamps will illuminate after entering a valid keypad entry code.

To unlock all doors, press the 3 • 4 control within five seconds.

To lock all doors, press the 7 • 8 and the 9 • 0 at the same time. You do not need to enter the keypad code first. Note: The interior lamps

will turn off.

control on the remote entry transmitter.

Autolock (if equipped)

This feature automatically locks all vehicle doors when the following conditions are met:

• the ignition key is in the 4 (ON) position,

• all the doors are closed,

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 88

Locks and Security

• the brake is pressed before reaching 5 mph (8 km/h), and

• the vehicle is traveling more than 5 mph (8 km/h).

Relock

The autolock feature repeats when the following conditions are met:

• the vehicle’s speed is less than 5 mph (8 km/h),

• any door is opened then closed while the ignition is in the 4 (ON)

position,

• the brake is pressed before reaching 5 mph (8 km/h), and

• the vehicle is traveling more than 5 mph (8 km/h).

To deactivate/reactivate the autolock feature using the keypad

Your vehicle comes with the autolock feature activated. To deactivate/reactivate this feature:

1. Ensure that the anti-theft system is not armed.

2. Turn the ignition to the 3 (OFF) position.

3. Close all the doors, liftgate and cargo doors.

4. Enter the 5-digit entry code.

5. Press and hold the 7 • 8. While holding the 7 • 8, press and release

the 3 • 4.

6. Release the 7 • 8.

The horn will chirp once when the system has been successfully deactivated.

The horn will chirp twice (one short and one long chirp) when the system has been successfully reactivated.

To deactivate/reactivate the autolock feature using the power door unlock control

You must complete Steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds.

1. Insert the key and turn the ignition to the 4 (ON) position.

2. Press the power door unlock control three times.

3. Turn the ignition from the 4 (ON) position to the 3 (OFF) position.

4. Press the power door unlock control three times.

5. Turn the ignition back to the 4 (ON) position. The horn will chirp.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 89

Locks and Security

6. Press the unlock control, then press the lock control. The horn will

chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. Note: Pressing the power door UNLOCK/LOCK button again will toggle between activating and deactivating the autolock feature.

7. Turn the ignition to the 3 (OFF) position. The horn will chirp once to

confirm the procedure is complete.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 90

Seating and Safety Restraints

SEATING

Notes:

Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the

event of a collision.

Do not pile cargo higher than the seatbacks to reduce the risk of injury in a collision or sudden stop.

Head restraints

The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.

The head restraints can be moved up and down. Lift the head restraint so that it is located directly or as close as possible behind your head.

Push control to lower head restraint.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 91

Seating and Safety Restraints

Full bench seat (if equipped)

• Lift the release bar to move the seat forward or backward. Ensure that the seat is relatched into place.

• Pull up on the lever located at the bottom of the seatback to quickly fold the seatback forward.

• Pull up on the lever located at the side of the seat cushion to recline the seatback and to return the seat to the upright position.

40/20/40 split bench seat (if equipped)

• Lift the track release bar to move the seat forward or backward. Ensure the seat is relatched into place.

• Pull the handle on the side of the seat up to recline the seat.

• Push down the lever located at the bottom of the seatback to quickly fold the seatback forward.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 92

Seating and Safety Restraints

40/20/40 front seat armrest and console (if equipped)

To release the armrest, pull forward on the strap and pull the armrest down.

To gain access to the storage compartment in your armrest, lift the latch to open the lid. The lid cannot be opened in the upright position.

Lift up armrest to return it to a center seatback.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 93

Seating and Safety Restraints

Captain’s chair (if equipped)

• Lift the bar to move the seat forward or rearward. Make sure that the seat is relatched into place.

• To recline the seatback, pull the release lever handle located on the side of the seat up.

• Push down the lever (if equipped) located at the bottom of the seatback to quickly fold the seatback forward.

Adjusting the front power seat (if equipped)

The control is located on the outboard side of the seat cushion.

Your vehicle will only be equipped with one of the two controls shown.

Press to raise or lower the front portion of the seat cushion.

• Type A

• Type B

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 94

Seating and Safety Restraints

Press to raise or lower the rear portion of the seat cushion.

• Type A

• Type B

• Type A

Press the control to move the seat forward, backward, up or down.

• Type B

Press the control to move the seat forward or backward.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 95

Seating and Safety Restraints

Using the manual lumbar support

For more lumbar support, turn the lumbar support control toward the front of vehicle.

For less lumbar support, turn the lumbar support control toward the rear of vehicle.

Heated seats (if equipped)

To operate the heated seats, do the following:

• Push control to activate.

• Push again to deactivate.

The indicator light on the control will illuminate when activated.

The system will not automatically shutoff unless control is pushed to deactivate. If system is not manually terminated at last use, then system will remain active at next ignition key cycle.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 96

Seating and Safety Restraints

REAR FOLDING SEAT SYSTEM WITH LOAD FLOOR (IF EQUIPPED)

The rear seatback has a split 60/40 seat. Each seat cushion can be flipped up into the seatback position.

1. Pull down the latch lever located

on the bottom seat back to fold the seat back forward.

2. Pull up on the lever located on

the side of the seat cushion to rotate the cushion up until it locks into a vertical storage position, gaining access to the grocery hook located on the underside of the driver-side seat cushion. The maximum load is 25 lbs (11 kg).

Returning the seat to seating position

• Pull lever on the side of the seat to release seat cushion from storage position.

• Push seat cushion down until it locks into horizontal position.

Always be sure that the seat is in a latched position, whether the seat is occupied or empty. If not latched, the seat may cause

injury during a sudden stop.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 97

Seating and Safety Restraints

To gain access to the cupholders and tray, pull down on the armrest.

To gain access to the 60/40 load floor, store the cushion in the upright locked position. Pull up on the straps located at the sides of the load floor, and rotate forward until resting on the carpet.

SAFETY RESTRAINTS

Safety restraints precautions

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

To reduce the risk of injury, make sure children sit in the back seat where they can be properly restrained.

Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from

injury in a collision.

All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag

supplemental restraint system (SRS) is provided.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 98

Seating and Safety Restraints

It is extremely dangerous to ride in a cargo area, inside or

outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly.

In a rollover crash, an unbelted person is significantly more likely

to die than a person wearing a safety belt.

Each seating position in your vehicle has a specific safety belt

assembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the outside shoulder only. Never wear the shoulder belt under the arm. 2) Never swing the safety belt around your neck over the inside shoulder.

3) Never use a single belt for more than one person.

Always transport children 12 years old and under in the back

seat and always properly use appropriate child restraints.

Safety belts and seats can become hot in a vehicle that has been

closed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them.

Combination lap and shoulder belts

1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 99

Seating and Safety Restraints

2. To unfasten, push the release button and remove the tongue from the buckle.

The front outboard and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front outboard passenger and rear seat outboard safety belts have two types of locking modes described below:

Vehicle sensitive mode

This is the normal retractor mode, which allows free shoulder belt length adjustment to your movements and locking in response to vehicle movement. For example, if the driver brakes suddenly or turns a corner sharply, or the vehicle receives an impact of approximately 5 mph (8 km/h) or more, the combination safety belts will lock to help reduce forward movement of the driver and passengers.

On SuperCab and Crew Cab models, the front seat belt system can also be made to lock manually by quickly pulling on the shoulder belt.

Rear seat belts (if equipped) cannot be made to lock up by pulling quickly on the belt.

Automatic locking mode

When to use the automatic locking mode

In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt.

This mode should be used any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible. Refer to Safety restraints for children or Safety seats for children later in this chapter.

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

Page 100

Seating and Safety Restraints

How to use the automatic locking mode

• Buckle the combination lap and shoulder belt.

• Grasp the shoulder portion and pull downward until the entire belt is pulled out.

• Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.

How to disengage the automatic locking mode

Disconnect the combination lap/shoulder belt and allow it to retract completely to disengage the automatic locking mode and activate the vehicle sensitive (emergency) locking mode.

After any vehicle collision, the front passenger and rear outboard

seat belt systems must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.

100

REVIEW COPY 2005 F250/350/450/550 (f23), Owners Guide (post-2002-fmt) (own2002),

Market: USA_English (fus)

FORD F-250, F-550, F-450 SD, F-350 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Table of Contents

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints