Fluke 190-062, 190-102, 190-104, 190-202, 190-204 Brochure

BUILT TOUGH

to keep up with you.

BUILT TOUGH

to keep up with you.

Over 20 years of ScopeMeter®

High performance handheld scopesHigh performance handheld scopes

Test Tool Innovation

190 Series II ScopeMeter® Portable Oscilloscopes

New

500 MHz

4 Ch

See more. Fix more.

ScopeMeter

portable oscilloscopes take you into territories where standard bench scopes can’t go: where it’s harsh, hazardous and dirty—without sacrificing any capabilities.

Compare waveforms and easily perform timing and amplitude measurements of 4 channels simultaneously.

500 MHz bandwidth and 5GS/s sampling can reveal signal noise and distortion that otherwise may go undetected.

5GS/s sampling or 200 ps sample resolution provides the detail needed to inspect signal edge dV/dt or signs of destructive

reflections.

The Fluke 190 Series II ScopeMeter® oscilloscopes, with electrically isolated channels, are safety rated for industrial applications. These scopes combine rugged portability with the high performance of bench oscilloscopes to take you from troubleshooting microelectronics all the way into power electronic applications—from dc to 500 MHz.

Choose from two or four channel models with a wide

range of bandwidth options. Fast sampling rates up to

5.0GS/s, 200 ps resolution and deep memory of 10,000 samples per channel allow high-accuracy capture and display of waveform details, noise, and other disturbances.

Perform timing or amplitude related measurements on three phases or three-axis control systems, or simply compare and contrast multiple test points in a circuit under test. Features like TrendPlot

™

and-View automation and process controls, and power electronics to minimize repair costs and downtime. These features make the oscilloscopes easy to use especially when diagnosing the most difficult problems like complex waveforms, induced noise, intermittent events and signal fluctuations or drift.

New Li-Ion battery technology keeps your scope on the job, all day.

Fluke 190 Series II ScopeMeter with two or four channels, 60MHz to 500 MHz. Choose the model that’s right for your application and budget.

help you quickly diagnose industrial machinery,

™

, ScopeRecord™, and Connect-

test tools are available

Built to withstand harsh environments with the highest safety ratings

Rated all the way to CAT IV

ScopeMeter® test tools are rugged solutions built for industrial troubleshooting. The new Fluke 190 Series II are double-insulated floating oscilloscopes safety rated for measurements in CATIII 1000V / CAT IV 600V environments.

Measure from mV to kV safely

Independent isolated inputs allow you to make measurements in mixed circuits having different ground references reducing the risk of accidental short circuits.

Conventional bench oscilloscopes without special differential probes and isolation transformers can only reference measurements to line power earth ground.

With standard probes that cover a wide application range from mV to kV, you’re ready for anything from microelectronics to heavy-duty higher voltage electrical applications.

IP-51 rated for harsh environments

Rugged and shock-proof, ScopeMeter® portable oscilloscopes are built for dirty, hazardous environments. With its sealed case, it can endure and airborne pollutants. Every time you reach for ScopeMeter scope you can be confident it will work reliably wherever your work takes you.

dust, drips, humidity

portable oscillo-

Overvoltage category In brief Examples

CAT IV Three-phase at

utility connection, any outdoor conductors

CAT III Three-phase

distribution, including singlephase commercial lighting

CAT II Single-phase

receptacle connected loads

CAT I Electronic

Refers to the “origin of installation,” that

•

is, where low-voltage connection is made to utility power

Electricity meters, primary overcurrent

•

protection equipment

Outside and service entrance, service

•

drop from pole to building, run between meter and panel

Overhead line to detached building,

•

underground line to well pump

Equipment in ﬁxed installations, such as

•

switchgear and polyphase motors

Bus and feeder in industrial plants

•

Feeders and short branch circuits,

•

distribution panel devices

Lighting systems in larger buildings

•

Appliance outlets with short connections

•

to service entrance

Appliance, portable tools, and other

•

household and similar loads

Outlet and long branch circuits

•

Outlets at more than 10 meters (30 feet)

–

from CAT III source

Outlets at more that 20 meters (60 feet)

–

from CAT IV source

Protected electronic equipment

•

Equipment connected to (source) circuits

•

in which measures are taken to limit transient over voltages to an appropriately low level

Any high-voltage, low-energy source

•

derived from a high-winding resistance transformer, such as the high-voltage section of a copier

Tab le 1. Overvoltage installation categories. IEC 61010 applies to low-voltage (< 1000 V) test eq uipment.

+ 7 hidden pages