WARMING DRAWER
I
NTEGRATED WB30SDEI
INSTALLATION GUIDE
US CA
Safety and warnings 5
Warming drawer models 6
Unpack your product 7
Electrical specifications 7
Parts supplied 8
Tools required 8
Product dimensions - 30" integrated models 9
Cabinetry dimensions - 30" integrated models 10
Front panel specifications 11
Installation options 11
Installing the drawer 14
Adjusting the depth 16
Adjusting the height 16
Installer checklist 17
CONTENTS
3
SAFETY AND WARNINGS
!
WARNING!
Tip Hazard
This product may tip. Keep children away and
take care. Failure to follow this advice may
result in injury.
• Drawer must be secured in place by supplied
screws.
Electric Shock Hazard
Failure to follow this advice may result in
electrical shock or death.
• If the product is damaged, switch the appliance
off and disconnect it from the mains to avoid
possible electric shock.
!
WARNING!
• Ensure there is a fixed shelf directly above
!
the drawer if it is not installed under another
product.
!
WARNING!
Cut Hazard
Failure to use caution could result in injury.
Weight Hazard
Failure to follow this advice may result in
damage or personal injury.
• Ensure the bottom shelf of the cabinetry can fully
support the weight of combined appliances.
WARNING!
• Take care: some edges may be sharp.
• Do not put fingers in the drawer when closing.
5
SAFETY AND WARNINGS WARMING DRAWER MODELS
READ AND SAVE THIS GUIDE
WARNING!
To reduce the risk of fire, injury to persons or damage when using the appliance, follow the
important safety guides listed below. Read all the instructions before using the appliance.
Installation
z
Please make this information available to the person installing the product.
z
The appliance must be installed by a qualified installer, or Fisher & Paykel trained and
supported service technician to avoid faulty electrical connection.
z
Ensure the installation complies with all clearance requirements and applicable standards
and regulations.
z
When installed in combination with a companion product, the companion product can be
placed directly onto the appliance. A built-in shelf at the base of the cabinetry must be
able to support the weight of both products.
z
Ensure the cabinetry is square and level and with correct dimensions.
z
If installing the appliance directly underneath an oven, ensure you do not damage the
oven’s lower trim. Fisher & Paykel does not accept any responsibility for any damage
resulting from incorrect installation.
z
Before installing the appliance, inspect for any signs of damage. Do not install or use
damaged appliances.
z
Be careful when stacking the appliances on top of each other to avoid damage to the
appliances.
Electrical
z
All connections for electrical power and earthing must be done by a qualified electrician
and must comply with local codes and ordinances.
z
Before installation, ensure that the voltage and frequency listed on the data plate
corresponds with the household electrical supply.
z
When combining with another appliance, ensure each appliance has its own power outlet.
Avoid sharing the power point to prevent accidental switching off of the appliance.
z
Ensure your appliance is properly grounded (earthed).
z
Connect the drawer to a properly rated, protected and sized power supply circuit to avoid
electrical overload.
z
Do not use an extension cord or a portable electrical outlet device (e.g. multi-outlet outlet
box) to connect the drawer to the power supply. Ensure the power supply cord is located
so that it will not be stepped on, tripped over or otherwise subject to damage or stress.
z
Ensure there is a switched outlet in an easily accessible area within 35 7/16” (900mm) of
the centre rear of the product.
30" Warming Drawer,
Integrated style
WB30SDEI
Servicing
z
Do not repair or replace any part of the appliance unless specifically recommended in the
user guide. All other servicing should be done by a Fisher & Paykel trained and supported
service technician or qualified person.
z
Always disconnect the power supply before doing any installation, maintenance or repair
work.
z
If the power supply cord is damaged, it must be replaced by a qualified electrician or
Fisher & Paykel trained and supported service technician.
6
UNPACK YOUR PRODUCT ELECTRICAL SPECIFICATIONS
Remove the warming drawer and accessories box from the packaging. Recycle the materials
that can be reused. Dispose packaging materials in accordance with local regulations on waste
disposal.
Inspect the warming drawer for any signs of damage. Do not install the warming drawer if it
has been damaged. If the product is damaged, contact your local Fisher & Paykel dealer.
RECYCLE
RESPONSIBLY
All electrical work must be done by a qualified electrician, or a Fisher & Paykel trained and
supported service technician.
WB30SDEI
Supply 110 VAC, 60 Hz
Service 10 amp circuit
Maximum Power 810 W
Power outlet* 3-prong grounding-type
Power cord (total length) 70 7/8" (1800mm)
* The power outlet must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.
7
PARTS SUPPLIED TOOLS REQUIRED
WARMING DRAWER
MINIMAL WB24SDEB2 & WB30SDEB1
CONTEMPORARY WB24SDEX2 & WB30SDEX1
PROFESSIONAL WB30SPEX1
SERVICE & WARRANTY
SERVICE ET GARANTIE
ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ
SERVIZIO E GARANZIA
SERVICE & GARANTIE
HUOLTO JA TAKUU
SERVICE OG GARANTI
保修和维修
服務和保修
(1)
T15 star head
wood screw (12)
INTEGRATED WB30SDEI1
USER GUIDE
US CA
User guide (1)
T15 star head
machine screw (6)
Side brackets (2) Bracket cover (5)
WARMING DRAWER
INTEGRATED W30SDEI
INSTALLATION GUIDE
US CA
Installation guide (1)Service & Warranty
Wire shelf (1)
Bracket spacer (1)
5mm Hex key T15 star-head
screwdriver
Leveler
Ruler
8
e
PRODUCT DIMENSIONS - 30" INTEGRATED MODELS
h
a
PLAN
b
c
i
g
ISOMETRIC
f
D
PRODUCT DIMENSIONS
WB30SDEI
IN MM
A Overall height 10 11/16 271
B Overall width 28 7/16 723
C Overall depth* 22 3/16 564
D Height of chassis 10 11/16 271
E Width of chassis 27 13/16 707
F Height of door frame 10 1/2 267
G Depth of door frame** 11/16 17
H Depth of open drawer 16 1/2 419
* Including power plug and drawer frame
** Measured from back of chassis flange to front of door frame.
WB30SDEI
PRODUCT WEIGHT
LBS KG
FRONT
Actual product dimension may vary by ± 2 mm.
Total weight of drawer* 75 34
*including packaging
PROFILE
9
CABINETRY DIMENSIONS - 30" INTEGRATED MODELS
d
b
a
PO*
PROFILE
e
PO*
c
f
WB30SDEI
CABINETRY DIMENSIONS
INCHES MM
A Minimum inside height of cavity 10 3/4 273
B Minimum inside width of cavity min 28 9/16 - max 28 3/4 min 725 - max 730
FLUSH INSTALL
custom panel
Actual product dimension may vary by ± 2 mm.
10
C Minimum inside depth of cavity 22 1/2 572
D Overall width of cabinetry 30 762
E Minimum clearance between top of door frame
and upper cabinetry panel
F Minimum clearance between bottom of door
frame and lower cabinetry panel
* The power outlet (PO) must be earthed and located within 35 7/16” (900mm) of the centre rear of the product.
1/8 3
1/16 2
FRONT PANEL SPECIFICATIONS
INSTALLATION OPTIONS
Ensure the back and sides of the panel and cabinetry around the drawer are completely sealed
with a waterproof vapour barrier (ie polyurethane) to prevent damage to the panel.
b
a
c
STANDALONE INSTALLATION
This installation is suitable for Minimal, Contemporary & Professional Warming drawers. A fixed
shelf must be installed above the warming drawer.
Top shelf
Warming Drawer
Bottom shelf
PROFILE
FRONT PANEL DIMENSIONS
WB30SDEI
IN MM
A Height of drawer front panel 10 1/2 267
B Width of drawer front panel 29 15/16 760
C Depth of drawer front panel 13/16 16-20
WB30SDEI
FRONT PANEL WEIGHT
LBS KG
Total weight of drawer front panel 11 5
FRONT
11
INSTALLATION OPTIONS
COMBINED WITH SINGLE OVEN
This combination is suitable for 24" and 30" Warming Drawers that can fully support
24" and 30" Fisher & Paykel wall ovens, respectively.
Single oven
Warming Drawer
Bottom shelf
PROFILE
COMBINED WITH COMPANION PRODUCT
This combination is suitable for 24" and 30" Warming Drawers that can fully support
24" and 30" Fisher & Paykel companion products, respectively.
Top shelf
Companion product
Warming Drawer
Bottom shelf
PROFILE
FRONT
12
FRONT
INSTALLATION OPTIONS
COMBINED WITH DOUBLE OVEN
This combination is suitable for 30" Warming Drawers that can fully support a
30" Fisher & Paykel double oven.
Double oven
Warming Drawer
Bottom shelf
PROFILE
COMBINED WITH SINGLE OVEN & COMPANION PRODUCT
This combination is suitable for 30" Warming Drawers. A shelf is required above the oven to
support the 30" companion product. Ensure the bottom shelf can fully support the weight of
all appliances.
Companion product
30” Companion Trim Kit
Top shelf
Wall oven
Warming Drawer
Bottom shelf
PROFILE
FRONT
FRONT
13
INSTALLING THE DRAWER
cabinet bracket
1
2
Check the base of the cabinetry
using a leveler or ruler.
Ensure the cabinetry is square
and base is level.
spacer
Use the supplied spacer to
locate the attachment position
of the cabinet brackets to
correct depth.
Secure the cabinet brackets to
the side panels of the cabinetry
with T15 wood screws (6x).
4
chassis flange
bracket cover
Secure the bracket cover and
chassis flange to the cabinet
brackets with T15 machine
screws (6x).
3
14
Connect the power plug at
the back of the drawer to the
power outlet.
Place the warming drawer
carefully inside the cabinetry.
5
Remove the backing of
adhesive tape on the door
frame.
Align the custom panel
carefully with the cabinetry.
6
shims
INSTALLING THE DRAWER
Ensure the custom panel is
correctly aligned and centered
before fixing to the tape as this
can only be done once.
Use shims (not supplied) to ensure
gaps are accurate.
8
Drill pilot holes into the custom panel
through the screw holes in the door
frame.
Be careful not to drill through the
panel.
Secure the custom panel to the door
frame with T15 wood screws (6x).
7
Open the drawer fully, and remove
the T15 screws from both sides of
the door frame.
Slide the door frame up and off the
drawer.
9
Slide the door frame back onto
the drawer and align the custom
panel vertically with surrounding
cabinetry.
Secure the door frame in place
with T15 screws.
15
ADJUSTING THE DEPTH ADJUSTING THE HEIGHT
The depth of the front panel of the warming drawer can be adjusted to align with the
surrounding cabinetry.
1
Open the drawer fully.
Using a hex key, turn the adjustment
screw to move the front panel forward.
Turn clockwise to move backwards or
counterclockwise to move forwards.
The front panel of the warming drawer can be adjusted vertically to align with the surrounding
cabinetry.
Open the drawer fully, and slightly
1
max 2mm
2
loosen the T15 screws.
Adjust to the required height and then
re-tighten the screws. The height is
adjustable within 2mm.
2
16
The depth is adjustable within 4mm.
3
Close the drawer and check the
alignment. Adjust again if necessary.
1h
2h
PRODUCT OFF
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
1h
2h
1h
2h
1h
2h
PRODUCT OFF
USER PRESSES ON/OFF BUTTON
ALL OTHER BEZELS GLOW WHITE EXCEPT
TEMPERATURE SETTING WHICH IS PRESET TO
MEDIUM AND GLOWS RED (PRODUCT STARTS
HEATING TO THE MEDIUM TEMPERATURE)
ON/OFF GLOWS RED UNTIL BUTTON IS PRESSED
AGAIN SHUTTING THE PRODUCT OFF.
1h
2h
1h
2h
INSTALLER CHECKLIST
IMPORTANT!
Read all installation instructions in this manual to see if the unit has been correctly installed.
Ensure that installation has been completed correctly before use.
Ensure that: Test operation:
F the warming drawer is level and securely fitted to the cabinetry.
F any internal packaging has been removed from the drawer.
F the isolating switch is accessible to the customer.
F the bottom shelf can fully support the total weight of the combined appliances.
Complete and keep for safe reference:
F Open the drawer.
F Press the
button to turn the warming drawer on.
F Shut the drawer.
F After 5-10 minutes, open the drawer to ensure heating has started.
F Press the
button to turn the warming drawer off and shut the drawer.
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
17
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2020. All rights reserved.
The models shown in this guide may not be available in all markets
The product specifications in this guide apply to the specific products and
models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time.
For current details about model and specification availability in your country,
please go to our website or contact your local Fisher & Paykel dealer.
and are subject to change at any time.
592266A 08.20
Loading...