Fisher & Paykel RDV3-304, RDV3-366, RDV3-488, RDV3-485GD, RHV3-484 Installation Guide

PROFESSIONAL RANGE

RDV, RHV & RIV

models

INSTALLATION GUIDE

US CA

WARNING!

If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any otherappliance.

NEVER use this appliance as a space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating of theappliance.

SAFETY AND WARNINGS

WARNING!

Electric Shock Hazard

Failure to follow this advice may result in electrical shock or death.

• Before carrying out any work on the electrical section of the appliance, it must be disconnected from the mains electricitysupply.

• Connection to a good ground wiring system is absolutely essential and mandatory.

• Alterations to the domestic wiring system must only be made by a qualified electrician

WARNING!

Cut Hazard

Failure to use caution could result in injury.

• Take care: some edges are sharp.

What to Do if you Smell Gas

• Do not try to light any appliance.

• Do not touch any electrical switch.

• Do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Failure to do so can result in death or seriousburns to children of adults.

• To reduce the risk of tipping the appliance, the appliance must be secured by properly installed anti-tip device packed with the appliance.

• A child or adult can tip the range and be killed.

• Install the anti-tip device to the structure by fastening the supplied bracket to the floor and wall following the instructions for installing the anti-tip device.

• Engage the anti-tip device.

• Re-engage the anti-tip device if the range ismoved.

WARNING!

SAFETY AND WARNINGS

WARNING!

Extremely Heavy

Failure to follow this advice may result in damage or personalinjury.

• Proper equipment and adequate manpower must be used in moving the range to avoid personal injury or damage to the unit or the floor. The unit is heavy and rests on adjustable steellegs.

WARNING!

To avoid hazard, follow these instructions carefully before installing or using thisappliance.

Please make this information available to the person installing the appliance– doing so could reduce your installation costs.

Save these instructions for the local inspectors use.

This range is to be installed and connected to the electricity supply only by an authorized person.

If the installation requires alterations to the domestic electrical system, call a qualified electrician. The electrician should also check that the socket cable section is suitable for the electricity drawn by the range.

Service should only be done by authorized technicians. Technicians must disconnect the power supply before servicing this appliance.

The range must be grounded.

Installation must comply with your local building and electricity regulations.

This appliance must be installed and connected to the mains power supply only by a suitably qualified person according to these installation instructions and in compliance with any applicable local building and electricity regulations. Failuretoinstall the appliance correctly could invalidate any warranty or liability claims.

Ensure the installer shows the customer where the gas supply shut-off valve is located.

If the power supply cable is damaged, it must be replaced by the manufacturer, itsservice agent or similarly qualified person in order to avoid a hazard.

A circuit breaker is recommended.

Do not use adaptors, reducers or branching devices to connect the oven to themainselectricity supply, as they can cause overheating and burning.

Improper installation, adjustment alteration, service or maintenance can cause property damage, injury or death. Read the installation, operating and maintenance instructions thoroughly before using, installing or servicing this appliance.

A risk of the appliance tipping over exists if the appliance is not installed in accordance with installation instructions.

DO NOT obstruct the flow of combustion or ventilation air to the appliance. Besureafresh air supply is available.

California Proposition 65–The burning of gas cooking fuel generates some by-products which are known by the State of California to cause cancer or reproductive harm. California law requires businesses to warn customers of potential exposure to such substances. To minimize exposure to these substances, always operate this unit according to the manufacturer’s instructions and provide good ventilation to the room when cooking with gas.

Check local building codes for the proper method of range installation. Localcodesvary. Installation, electrical connections, and grounding must comply with all applicable codes. In the absence of local codes, the range should be installed in accordance with the latest edition of National Fuel Gas Code ANSI Z223.1 and National Electrical Code ANSI/NFPA 70.

In Canada: Installation must be in accordance with the current CAN/CGA B149.1&2 Gas Installation codes and/or local codes. Electrical installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes Part 1 and/ or local codes.

Be sure that the unit being installed is set up for the kind of gas being used. The gasrange is shipped from the factory set and adjusted for Natural Gas or LP (propane), depending on the specific model ordered. Verify that the range is compatible with the gas at the installation site before proceeding further. Returnrange to dealer if the unit is not set for site gas supply.

The appliance must not be installed behind a decorative door in order to avoid overheating.

Do not lift the range by the door handle. Doing so may damage the product.

Before use, ensure all doors are correctly installed.

Two persons are required to move the product safely to the installation location.

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher&Paykel dealer.

MODEL IDENTIFICATION

RDV3-304

RIV3-304 RDV3-366 RIV3-365

RDV3-488 RHV3-484 RDV3-485GD

PARTS SUPPLIED FOR INSTALLATION

Anti-tip bracket (1) 5/16" x 1 1/2"

#10 x 2" wood screws (4)

sleeve anchors (2)

Lag bolts and washers (2)

Foot cover sets (2)

PRODUCT DIMENSIONS–30" MODELS

PLAN

J D

PROFILEFRONT

PRODUCT DIMENSIONS

A Overall height of range

(from floor to cooktop, excl. pan supports andvent trim)

30" MODELS

IN MM

min 35 3/4

max 36 3/4

min 908

max 933

B Overall width of range 29 7/8 759

C Overall depth of range (excl. handle and dials) 29 1/8 740

D Depth from rear of chassis to cabinetry face – projecting control panel 25 3/8 644

E Depth from rear of chassis to cabinetry face – flush control panel 27 11/16 703

F Height from top of cook surface to top of pan supports 1 9/16 40

G Height from top of cook surface to top of

vent trim (if fitted)

angled vent trim (if fitted)

1 3/4

3 1/2

H Height from top of cook surface to bottom of chassis 35 1/4 895

I Adjustable feet height min 1/2

max 1 1/2

min 13

max 38

J Depth of open door to front control panel 19 1/8 486

PRODUCT DIMENSIONS–36" MODELS

PLAN

J D

PROFILEFRONT

PRODUCT DIMENSIONS

A Overall height of range

(from floor to cooktop, excl. pan supports andvent trim)

36" MODELS

IN MM

min 35 3/4

max 36 3/4

min 908

max 933

B Overall width of range 3 5 7/ 8 911

C Overall depth of range (excl. handle and dials) 29 1/8 740

D Depth from rear of chassis to cabinetry face – projecting control panel 25 3/8 644

E Depth from rear of chassis to cabinetry face – flush control panel 27 11/16 703

F Height from top of cook surface to top of pan supports 1 9/16 40

G Height from top of cook surface to top of

vent trim (if fitted)

angled vent trim (if fitted)

1 3/4

3 1/2

H Height from top of cook surface to bottom of chassis 35 1/4 895

I Adjustable feet height min 1/2

max 1 1/2

min 13

max 38

J Depth of open door to front control panel 19 1/8 486

PRODUCT DIMENSIONS–48" MODELS

PLAN

PROFILEFRONT

PRODUCT DIMENSIONS

A Overall height of range

(from floor to cooktop, excl. pan supports andvent trim)

48" MODELS

IN MM

min 35 3/4

max 36 3/4

min 908

max 933

B Overall width of range 47 7/ 8 1216

C Overall depth of range (excl. handle and dials) 29 1/8 740

D Depth from rear of chassis to cabinetry face – projecting control panel 25 3/8 644

E Depth from rear of chassis to cabinetry face – flush control panel 27 11/16 703

F Height from top of cook surface to top of pan supports 1 9/16 40

G Height from top of cook surface to top of

vent trim (if fitted)

angled vent trim (if fitted)

1 3/4

3 1/2

H Height from top of cook surface to bottom of chassis 35 1/4 895

I Adjustable feet height min 1/2

max 1 1/2

min 13

max 38

J Depth of open door to front control panel 19 1/8 486

+ 16 hidden pages