Fisher Paykel DW24U6I1 Installation Manual

DISHWASHER

DW24U6I1 & DW24U2I1 models

INSTALLATION GUIDE

US CA

591955B 07.19

SAFETY AND WARNINGS

COMPONENTS

TOOLS

TECHNICAL DATA

BEFORE INSTALLATION

APPLIANCE DIMENSIONS

CABINETRY DIMENSIONS

ELECTRICAL AND PLUMBING PREPARATION

CAVITY PREPARATION

ATTACH INFILL BRACKET

CUSTOM DOOR PANEL PREPARATION

[A] DRILL PILOT HOLES USING SUPPLIEDTEMPLATE [B] MANUALLY MARK AND DRILL PILOT HOLES OR

ATTACHING CUSTOM DOOR PANEL

LEVEL DISHWASHER

ALIGN APPLIANCE IN CABINETRY

ELECTRICAL CONNECTION

HARD PLUMBING

PLUMBING AND DRAINAGE OPTIONS

TOE KICK INSTALLATION

SECURE THE APPLIANCE

[A] FIX THE PRODUCT TO ADJACENT CABINETRY [B] FIX THE APPLIANCE TO BENCHTOP ABOVE

CONNECT INLET HOSE TO HOT WATER

CONNECT TO POWER

TROUBLESHOOTING

FINAL CHECKLIST

IMPORTANT!

SAVE THIS INSTALLATION GUIDE

The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, go to our website fisherpaykel.com or contact your local Fisher&Paykel dealer.

1 SAFETY AND WARNINGS

WARNING!

Electrical Shock Hazard Before installing the dishwasher, remove the house fuse or open the

circuitbreaker. Ensure that a qualified electrician or service representative has checked

ifthe appliance is properly grounded. Improper connection of equipment-grounding conductor can result to

riskof electric shock. Do not modify the power supply plug provided with the appliance — if it will

not fit the outlet, have a proper outlet installed by a qualified electrician. Do not use an extension cord, adapter plug or multiple outlet box. Ensure the dishwasher is completely enclosed at the time of installation

toreduce the risk of electrical shock, fire, or personal injury. Ensure the dishwasher is disconnected from the power supply before

fittingthe front panels. Ensure components such as panel bracket and any custom metal

component (eg handle) that extends past the rubber seal, are electrically grounded after installing the front panels.

Failure to follow these advice may result in electrical shock or death.

WARNING!

Cut Hazard Take care — panel edges are sharp. Failure to use caution could result in injury or cuts.

IMPORTANT SAFETYGUIDE

This dishwasher is manufactured for indoor use only.

Ensure to follow safety and the warnings to prevent electrical shock, injury or fire.

Ensure to remove all packaging materials supplied with the dishwasher.

This dishdrawer is intended for connection to the hot-water supply.

The dishwasher MUST be installed to allow for future removal from the enclosure if service is required.

Installation of this dishwasher requires basic mechanical and electricalskills.

Installation must comply with your local building, electricity, and plumbing regulations.

It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codesand Regulations.

The switched power outlet must be located outside the dishwasher cavity to allow easy access after installation. Take care when installing or removing the appliance to avoid possible damage to the power supply cord andhoses.

If the dishwasher is to be relocated from one installation to another it must bekept upright to avoid damage from water spillage.

Make sure only new hoses are used for connection (supplied with the dishwasher). Oldhoses should not be reused.

Failure to install the dishwasher correctly could invalidate any warranty or liability claims.

Fitting integrated front panels requires access to electrical service areas. This work must be performed and certified by a qualified electrical service technician.

Ensure the appliance is not plugged in when fitting custom panels.

Failure to install the custom panels correctly could invalidate anywarranty or liabilityclaims.

At the completion of the dishwasher installation, the Installer mustperform theFinalChecklist.

GROUNDING

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electriccurrent.

Thisappliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.

If the dishwasher is installed as a permanently connected appliance: This appliance must be connected to a grounded metal, permanentwiring system,

or anequipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on theappliance.

2 COMPONENTS 3 TOOLS

Supplied parts

Drain hose support (1)

Moisture protection tape for cabinetry (1)

Ø3.5 x 1/2” (12mm) screws (4)

Ø3.9 x 1 1/2” (38mm) screws (4)

Plastic slider (1)

Mounting brackets for wood countertop or side cabinets (2)

Ø4 x 1” (25mm) screws (4)

Ø3.9 x 1/2” (13mm) screws (4)

Required parts

UL-listed wire nuts (3)

Thread seal tape (1)

Components for new installation only (available in hardware stores)

Air gap for drain hose (use only if required)

3/4”(16mm) Strain relief for electrical connection

Waste tee for house plumbing (use only if required)

Screw-type hose clamps

3/4”(19mm) Elbow 90° (1)

Required tools

Phillips-head screwdriver

Powered drill Adjustable wrench 6”

Safety glasses Torch Gloves

Nutdriver 1/4” (6.35mm) and 5/16” (7.94mm)

(152.4mm)

Torque driver T25

Measuring tape

DISHWASHER

DW24U6I1 & DW24U2I1 models

INSTALLATION GUIDE

US CA

Installation guide (1)

DOOR PANEL TEMPLATE GABARIT DE PANNEAU DE PORTE

591518B 05.19 591518B 05.19

Centre line

Ligne centrale

Pilot holes

Avant-trous

Utilisez ce gabarit pour percer avec précision les avant-trous destinés à la fixation de votre panneau de porte encastré.

Déterminez la hauteur de porte appropriée ci-dessous et alignez le gabarit avec la base de votre panneau de porte. Pour les instructions d’installation complètes, reportez-vous au Guide d’installation fourni avec votre appareil.

Partie saillante de la porte : 1 5/16 po – 2 1/8 po (34 mm – 54 mm)

Partie saillante de la porte : 2 1/8 po – 2 15/16 po (54 mm – 74 mm)

Door overhang: 1 5/16" – 2 1/8" (34mm – 54mm)

Door overhang: 2 1/8" – 2 15/16" (54mm – 74mm)

Use this template to accurately drill the required pilot holes in your custom door panel.

Establish the appropriate dimension below and align the template with the base of your panel.

For full installation guidance, refer to the Installation Guide supplied with your appliance.

Door panel template (1)

DISHWASHER

DW24U2I and DW24U6I

models

USER GUIDE

US CA

User guide (1)

SERVICE & WARRANTY

SERVICE ET GARANTIE

ΣΈΡΒΙΣ ΚΑΙ ΕΓΓΎΗΣΗ

SERVIZIO E GARANZIA

SERVICE & GARANTIE

HUOLTO JA TAKUU

SERVICE OG GARANTI

保修和维修

服務和保修

Service & Warranty (1)

Hot water line with ferrule and compression nut – min 3/8” (9.5mm) copper tubing or flexible braided hose

Hand shut-off valve (recommended)

ØElectrical cable or Power cord kit (5’ 4” long) or (7’ 9” long) depending on your installation

Bucket – for flushing

Tubing cutter Hole saw set

the line

Level Carpenter’s square

Allen key 1/4” (6mm)

4 TECHNICAL DATA

Technical data

Check the electrical data on the rating label (located on the left-hand side of the dishwasher’s stainless steel inner door). If the data on the rating label are different to the specification below, consider the data as correct.

DW24U2I1 models DW24U6I1 models

Capacity 12 place settings 14 place settings

Mains water pressure 0.03-1 MPa (= 0.3-10 bar) 0.03-1 MPa (= 0.3-10 bar)

Power voltage 120V (60 Hz) 120V (60 Hz)

Maximum current intensity 8.9 A 8.9 A

Total absorbed power 1050 W 1050 W

Anti-flood protection

This dishwasher has anti-flood protection which will stop the water flowing in the event ofaleak within the machine.

5 BEFORE INSTALLATION

Unpacking and handling

Check packaging and dishwasher for signs of transport damage. Do not install if the dishwasher is damaged. Contact the dealer where you purchased the dishwasher.

We recommend to recycle some of the packaging. Check the symbols and labels toensureif recycling is possible.

Always be careful with the hoses and power cord at the back of the dishwasher. Ensurethey are not squashed, kinked or cut to prevent damage and malfunction.

Connections and services

Do not use extension cords or multi-outlet power boards to connect the dishwasher tothepower supply.

Do not connect the dishwasher to a water system where the temperature exceeds 140°F (60°C), or where there is no temperature control, eg wetback system, unless the system isfitted with a suitable tempering valve.

Do not connect the dishwasher to an undersink high-pressure ‘push-through’ type hot water system to prevent damage to the system.

NOT TO SCALE

6 APPLIANCE DIMENSIONS

B C

FRONT

PLAN

PROFILE

DW24U6I1/DW24U2I1 models

APPLIANCE DIMENSIONS in mm

Overall height of appliance*

Overall width of appliance (excl. side seals) 23 3/4 603

Overall depth of appliance (excl. custom panel & handle) 21 3/4 552

Height from floor to bottom of custom panel 4–8 100–212

Depth of open door (measured from front of chassis) (excl. custom panel) 23 7/8 606

* depending on adjustment of levelling feet

CUSTOM PANEL DIMENSIONS in mm

Height of custom door panel*

Width of custom door panel* 237/16–2313/16 596–605

Depth of custom door panel* 5/8–3/4 16–19

CUSTOM PANEL WEIGHT lbs kg

Overall weight of custom door panel 8.9–17.6 4–8

* depending on cabinetry dimensions

32 1/4–34 5/8 820–880

26 3/16–30 665–717

7 CABINETRY DIMENSIONS

PLAN

DW24U6I1/DW24U2I1 models

CABINETRY DIMENSIONS in mm

Inside width of cavity 24 610

Inside height of cavity* 32 1/4–34 5/8 820–880

Inside depth of cavity min. 22 5/8 min. 574

* depending on adjustment of levelling feet

DW24U6I1/DW24U2I1 models

CLEARANCE DIMENSIONS in mm

Clearance from corner cupboard 1/2 13

Clearance to adjacent cupboard door min. 1/16 2

PROFILE

l m

PLAN

8 ELECTRICAL AND PLUMBING PREPARATION

Select plumbing option

Hose connection

Copper pipe connection

Refer to ‘Plumbing and Drainage options’ (page 16) for more information.

Left side of

appliance

Supply area dimensions

Final position of dishwasher against wall

SECTION inches mm

C B

A A

5 127

4 102

2 51

3 76

9 CAVITY PREPARATION

COUNTERTOP

3/8” (10mm)

Moisture protection tape must be applied

WARNING!

Incorrect placement of the hole will result in damage to hoses.

IMPORTANT!

The power outlet must be located in a cabinet adjacent to the dishwasher cavity. 110-120 VAC max. 15 A

Ø 1 1/2” (38mm)

max. 17 11/16” (450mm)

Water Connection

Recommended HOT (Maximum 140°F/60°C).

Supplied hose to suit 3⁄8” (9mm) male compression fitting.

Water Pressure

Water softener models

Max. 1 MPa (145 psi) Min. 0.1 MPa (14.5 psi)

Models without water softener

Max. 1 MPa (145 psi) Min. 0.03 MPa (4.3 psi)

Max 1/4” (5mm)

Max distance between hole edge and rear inner face

Max 1/2” (10mm)

Max distance between hole edge and floor

Service Holes

Can be located either side of dishwasher, close to the rear face and the floor, as illustrated, for access to the water supply and drain.

If the hole is through wood, make sure its edges are smooth androunded.

If the hole is through metal, ensure you fit the supplied Edge Protector to prevent damage to the power cord.

min. 7 7/8” (200mm)

IMPORTANT!

When connecting drain line to disposer, check to be sure that drain plug has been removed. Dishwasher will not drain if plug is left in place.

Remove drain plug

IMPORTANT!

The infill bracket is installed as a cosmetic feature to fill the empty space visible for cabinets with cavity height of 35.5” or above.

Installation of infill bracket is not needed for cabinets with ADA standard.

!0 ATTACH INFILL BRACKET

side wings

1 Remove upper mounting bracket and plastic plugs

Open the door.

Unscrew the upper mounting bracket from the top ofthe appliance.

Push a small screwdriver downward through the screwhole from the top of the appliance to remove the plastic plug.

2 Install the infill bracket

Remove two screws pre-installed from the infillbracket.

Use the same screws to attach the bracket to the topof the appliance. Do not tighten fully.

3 Align and adjust appliance in cabinetry

Push the appliance into the cabinetry. Ensuretheinfillbracket do not hit the top of the cabinet while pushing. (Refer to ‘Align appliance in cabinetry’ for more details.)

Slide the side wings of the bracket outward to cover the hollow space.

Hand tighten the two screws.

IMPORTANT!

Ensure the custom door panel has the correct specifications tofitthe front of thedishwasher.

Ensure the back andsides of the panel are completely sealed with a waterproof vapor barrier (ie polyurethane). The barrier allows thepanel to withstand moisture (122°F (50°C) @ 80% RH) andprevent damage during hot and wet environment.

Measure the panel and overhang

!1 CUSTOM DOOR PANEL PREPARATION

Measure the custom panel and check the overhang length from the base of the door.

(when using an infill bracket)

[A] DRILL PILOT HOLES USING SUPPLIEDTEMPLATE

Using the supplied Door Panel Template, mark out and drill the required pilot holes into your custom panel. Ensure pilot holes are 1/16” (2mm) wide and 1/2” (12mm) deep.

DOOR PANEL TEMPLATE GABARIT DE PANNEAU DE PORTE

591518B 05.19 591518B 05.19

Upper overhang detail

If the template is not available, mark the pilot holes manually on your custom panel based on measurements in the below table. Ensure pilot holes are 1/16” (2mm) wide and 1/2” (12mm) deep.

If overhang is between 1 5/16” (34mm) and 2 1/8” (54mm):

PANEL A MEASUREMENTS in (mm)

Base of panel to lower bracket hole

Base of panel to upper bracket hole 4 7/8 (124)

Base of panel to handle holes 18 9/16 (472)

Centre line to handle holes 9 1/4 (235)

If overhang is between 2 1/8” (54mm) and 2 15/16” (74mm):

1 5/16–2 15/16” (4-74mm)

Lower overhang detail

(all custom panel installations)

[B] MANUALLY MARK AND DRILL PILOT HOLES

D D

4 1/16 (103)

Use this template to accurately drill the required pilot holes in your custom door panel.

Establish the appropriate dimension below and align the template with the base of your panel.

For full installation guidance, refer to the Installation Guide supplied with your appliance.

Door overhang: 1 5/16" – 2 1/8" (34mm – 54mm)

Door overhang: 2 1/8" – 2 15/16" (54mm – 74mm)

PANEL B MEASUREMENTS in (mm)

Base of panel to lower bracket hole

Centre line

Ligne centrale

Pilot holes

Avant-trous

Utilisez ce gabarit pour percer avec précision les avant-trous destinés à la fixation de votre panneau de porte encastré.

Partie saillante de la porte : 1 5/16 po – 2 1/8 po (34 mm – 54 mm)

Partie saillante de la porte : 2 1/8 po – 2 15/16 po (54 mm – 74 mm)

Base of panel to upper bracket hole 5 11/16 (144)

Base of panel to handle holes 19 3/8 (492)

Centre line to handle holes 9 1/4 (235)

Note: measurements are to center of holes.

4 13/16 (123)

Top screw detail

(between panel and screw head)

3mm

!2 ATTACHING CUSTOM DOOR PANEL

1 Fix slider bracket and screws to custom panel

Insert Ø3.9 x 1/2” (13mm) screws through the top two pilot holes. Fix the slider bracket to the panel through the lower pilot holes.

Increase

Decrease

4 Balance the door

Check the door balance by opening and closing the door. If the door drops when released, increase the tension. If the door rises when released, decrease the tension.

2 Hang custom panel onto the door

Close the door of the dishwasher and align the screws and the bracket on the custom panel to the front of the dishwasher door.

5 Secure the custom panel

Open the door and remove the four screws and replace with Ø3.9 x 1 1/2” (38mm) screws to fix the panel into place.

3 Adust the placement of the custom panel

Slide the custom panel up or down to position it in the desired location.

Screw locations

(repeat on both side of appliance)

!3 LEVEL DISHWASHER

IMPORTANT!

Ensure the appliance is leveled for proper dish rack, wash performance and door operation.

To verify dishwasher is leveled, open and close the door and pull the dish racks half way out. Thedoorshould fit in the tub opening without hitting the sides. Iftheracks roll on their own, or the door hits the side of tub, re-level.

0-1/4 (0-6.4mm)

1 Remove toe kick and mounting plate

To access the rear leg adjustment pin, you will need to remove the four screws holding the toe kick and mounting plate. Set screws aside for re-installation.

!4 ALIGN APPLIANCE IN CABINETRY

IMPORTANT!

Ensure top of door is aligned flush with surrounding cabinetry.

Use floor protection before sliding the appliance into the cabinetry. Remove the protection once the appliance is positioned in thecabinetry.

As you push the appliance in, pull through hoses and cord, ensure they don’t get kinked or twisted.

Note: If using an infill bracket for cabinets with cavity height of 35.5” or above, refer to ‘Attach infill bracket’ (page 10) for moredetails.

2 Adjust leg height

Adjust the rear foot via the back leg adjustment pin using an Allen Key. The front feet can be adjusted using an adjustable wrench.

Center appliance

floor protection

+ 33 hidden pages

Fisher Paykel DW24U6I1 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

CONTENTS

1 SAFETY AND WARNINGS

2 COMPONENTS 3 TOOLS

4 TECHNICAL DATA

5 BEFORE INSTALLATION

6 APPLIANCE DIMENSIONS

7 CABINETRY DIMENSIONS

8 ELECTRICAL AND PLUMBING PREPARATION

9 CAVITY PREPARATION

!0 ATTACH INFILL BRACKET

!1 CUSTOM DOOR PANEL PREPARATION

[B] MANUALLY MARK AND DRILL PILOT HOLES

!2 ATTACHING CUSTOM DOOR PANEL

!3 LEVEL DISHWASHER

!4 ALIGN APPLIANCE IN CABINETRY