Installation Instructions
NZ, AU Installation Information
Astro P
BI452
Aeron A,
Aeron E
BI602
Astro Double
BI602
Astro E,
Astro X
BI602
Astro Tower
BI602
542065C 05.2005 NZ
BI452 Series
Compact Built-In Oven
BI602 Series
Single Built-In Oven
595 mm
554 mm
435 mm
2
5
6
4
m
595 mm
554 mm
595 mm
450 mm
3
1
5
m
m
0
m
m
m
440 mm
m
m
0
0
6
580 mm
2
5
6
4
0
m
m
m
m
585 mm
6
4
6
0
m
m
m
m
0
0
≥570 mm
20 mm
600 mm
≥570 mm
20 mm
600 mm
16-20 mm 16-20 mm
1
BI602 Series
Double Built-In Oven
BI602 Series
Tower Built-In Oven
554 mm
917 mm
5
6
4
595 mm
554 mm
932 mm
4
6
0
m
m
2
0
m
m
m
m
3
1
5
m
m
922 mm
1062 mm
2
0
5
6
4
m
m
m
m
595 mm
1067 mm
1077 mm
4
6
0
m
m
≥570 mm
20 mm
m
m
0
0
6
≥570 mm
20 mm
600 mm
16-20 mm 16-20 mm
m
m
0
0
6
600 mm
2
Warnings and Safety information
Before you start
WARNING!
Cut Hazard
Tak e care - pa nel
edges are sharp.
Failure to use caution
could result in minor
injury or cuts.
CAUTION!
In order to avoid hazard these products
Please follow installation information
Failure to install the product correctly
The product is to be connected to the
must be installed according to these
instructions.
carefully. If in doubt consult your local
building authority by-laws.
could invalidate any warranty or liability
claims.
electrical supply only by a suitably
registered electrical person.
IMPORTANT!
Please make this information available to
the person responsible for installing the
product as it could reduce your installation
costs.
The cavity must be a completely sealed
box with no gaps. This will ensure the
cooling air flows under the product and
through the oven frame to give the correct
venting and cooling for the oven and
cabinet surround. Failure to seal the cavity
box may cause distortion of surrounding
cabinetry.
Read these instructions carefully before
installing or using this product.
Ensure a suitable disconnection switch
is incorporated in the permanent wiring,
mounted and positioned to comply with the
local wiring rules and regulations. The switch
must be of an approved type installed in
the fixed wiring and provide a 3 mm air gap
contact separation in all poles in accordance
with the local wiring rules.
In Australia and New Zealand, a switch of the
approved type with a 3 mm air gap must be
installed in the active (phase) conductor of
the fixed wiring.
Ensure that the location of the oven
connection socket (if fitted) is outside the
installation space if the product is flush to the
rear wall.
Ensure the electrician provides sufficient
free length of mains cable to reach from the
bottom rear of the cavity to at least 1.5 metres
in front of the bottom edge of the opening.
The cable may enter the cavity from the side,
top or bottom, but entry must be at the rear
of the cavity.
Ensure that the benchtop and oven cavity are
square and level.
Use easy-to-clean finishes for the wall surfaces
surrounding the oven and cooktop. This
will help to remove any staining caused by
cooking fumes.
Check that the height of the product from the
floor suits the user.
Ensure that the oven door(s) will be clear of
obstructions when fully opened.
3
Installation Instructions
Installation instructions
1
Check that the oven cavity is square and
within the limits specified.
2
Remove the mains wiring access cover.
3
Connect the mains wiring and refit the
access cover.
4
Remove the oven door and accessories and
slide the oven into place. Centre the oven
in the cavity, leaving a space of 2.5 mm on
each side between the door edge and the
joinery.
5
Use the four ‘wood screws’ and washers
supplied to secure the oven to the cavity,
through the holes in the oven frame. See the
flush fitting installation options.
6
Test the oven then refit the door and
accessories. Check that the oven is firmly
secured in the oven cavity.
Installing a cooktop above the
oven
If installing a cooktop above the oven ensure
adequate clearance is provided for the
cooktop as per the cooktop manufacturer’s
instructions.
Flush fitting installation options
B
20 mm
2.5 mm
C
20 mm
2.5 mm
CUPBOARD FRONT
D
20 mm
DRAWER FRONT
2.5 mm
4
Notes
5
Notes
6
Loading...