Page 1
IMPORTANT!
PLEASE MAKE THIS INFORMATION AVAILABLE TO YOUR JOINER AS IT
COULD REDUCE YOUR INSTALLATION COST.
Fisher & Paykel
INSTALLATION INFORMATION
Built-In Ovens
BI601 Series - Built-In Oven
BI601D Series - Built-In Double Oven
BI601XC2 Series - Built-In Oven/Microwave Combination
BI451 Series - Built-In Compact Oven
CAUTION: In order to avoid a hazard these appliances must be installed
according to these Installation Instructions.
Please follow installation information carefully.
If in doubt consult your local building authority by-laws.
BEFORE YOU START
DO Ensure a suitable disconnection switch is incorporated in the permanent wiring,
mounted and positioned to comply with the local wiring Rules and Regulations.
DO Ensure that the location of the Oven connection socket is outside the installation
space if the appliance is flush to the rear wall.
DO Ensure the benchtop and the Oven cavity are square and level.
DO Ensure the electrician allows as least 1.5m free length of connection cable within the
cavity for ease of installation and service of the Oven.
DO Use easy to clean finishes for the wall surfaces surrounding the Oven and Cooktop to
aid removal of any cooking fume staining resulting from use of the Oven and
Cooktop.
DO Ensure that the interconnection cord between the Cooktop and the Oven is not
accessible via cupboard doors after installation. This applies to any extension cords as
well, even though they are double insulated.
DO Consult local building authorities and by-laws if in doubt regarding installation.
DO Check the height from the floor suits the user.
DO Ensure the cavity is a completely sealed box with no gaps. This will ensure the
cooling air flows under the product to give the correct venting and cooling for the
oven and cabinet surround.
Page 1
Page 2
BUILT-IN OVEN INSTALLATION INSTRUCTIONS
1. Check that the kitchen cavity is square and within the limits in the INSTALLATION
DIMENSIONS.
2. Lift oven and slide into place. Secure Oven in cavity using 4 'wood screws' and washers
supplied through enamelled frame at either side of oven as shown in Flush Fitting
Installation Diagram.
3. Check that the Oven is firmly secured in the kitchen unit.
4. When installing the oven it is essential to centre the product in the cavity giving a spacing
of 2.5mm from the door edge to the joinery.
NOTE: If installing a Cooktop above the Oven ensure adequate clearance is provided for
the Cooktop as per the Cooktop Manufacturer's Instructions.
If installing a BI601 Single Built-In Oven with Wall Trim Kit, ensure you use
instructions that accompany that kit, Part No. 447915.
Flush Fitting
Installation Diagrams
Cabinetry adjacent to ovens must have a minimum temperature rating of 90°C as stated in
AS/NZS 3350.2.6
Page 2
Page 3
Height Recommendation Guide
Figures are based on an average height of 1650mm (5'5") wearing shoes.
The height of the product may vary + 50mm according to the height of the most frequent
user.
Page 3
Page 4
BI601 Series - Built-In Oven
Overall Overall
Width Height Depth
Oven Dimensions 595mm 595mm 562mm
Cabinet Dimensions 568mm 585mm 550mm
Please Note: Oven front dimensions differ from cabinet dimensions.
Product Dimensions
Top View
Side View
Page 4
Page 5
BI601D Series - Built-In Double Oven
Overall Overall
Width Height Depth
Oven Dimensions 595mm 932mm 562mm
Cabinet Dimensions 568mm 922mm 550mm
Please Note: Oven front dimensions differ from cabinet dimensions.
Product Dimensions Top View
Side View
Page 5
Page 6
BI601XC2 Series - Built-In Oven/Microwave Combination
Overall Overall
Width Height Depth
Oven Dimensions 595mm 932mm 562mm
Cabinet Dimensions 568mm 935mm 550mm
Please Note: Oven front dimensions differ from cabinet dimensions.
Product Dimensions Top View
Side View
Cabinet Detail View
Page 6
Page 7
BI601XC Series - Built-In Oven/Microwave Combination
Overall Overall
Width Height Depth
Oven Dimensions 595mm 932mm 562mm
Cabinet Dimensions 568mm 935mm 550mm
Please Note: Oven front dimensions differ from cabinet dimensions.
Product Dimensions Top View
Side View
Cabinet Detail View
Page 6
Page 8
BI451 Series - Built-In Compact Oven
Overall Overall
Width Height Depth
Oven Dimensions 595mm 450mm 562mm
Cabinet Dimensions 568mm 440mm 550mm
Please Note: Oven front dimensions differ from cabinet dimensions.
Product Dimensions Top View
Side View
Page 7
Page 9
Part No. 540784C August 2001
Page 10
INSTALLATION INSTRUCTIONS FOR
CT560X, CT560C, CT5602F, CT2802, CT6552S,
& BICT600 SERIES COOKTOPS
IMPORTANT!
PLEASE MAKE THIS INFORMATION AVAILABLE TO YOUR JOINER AS IT
COULD REDUCE YOUR INSTALLATION COST.
CAUTION: In order to avoid a hazard these appliances must be installed
according to these Installation Instructions.
BEFORE YOU START
DO Ensure a suitable disconnection switch is incorporated in the permanent wiring,
mounted and positioned to comply with the Local Wiring Rules and Regulations.
DO Ensure the bench is square and level.
DO Use easy to clean finishes for the wall surfaces surrounding the Cooktop to aid
removal of any cooking fume staining resulting from use of the Cooktop.
DO Consult local building authorities and by-laws if in doubt regarding installation.
DO Ensure that the interconnection cord between the Cooktop and the Oven or control
Box is not accessible via cupboard doors after installation. This applies to any
extension cord as well, even though they are double insulated.
Note:
Ensure that there is a minimum of 60mm between the cutout and the rear
or side wall.
If the cutout is less than 100mm from the wall, some form of protection against heat
should be used, such as ceramic tiles.
If prolonged use is anticipated, or the cooktop is mounted above a drawer
space, a barrier between is recommended.
The CT560X should not be installed directly above a dishwasher as the humidity
may damage the electronics.
Page 11
Cooktop Cutout Dimensions
MINIMUM DEPTHS
CT560X 60mm
CT560C 60mm
CT5602F 60mm
CT2802 60mm
CT6552S 65mm
BICT600 50mm
COOKTOP DIMENSIONS CLAMPING DOWN COOKTOP
TYPE LENGTH WIDTH DEPTH Place the cooktop into the cutout
CT560X 578mm 511mm 51mm and tighten with the supplied clamps.
CT560C 578mm 511mm 51mm
CT5602F 578mm 511mm 51mm These will cope with bench thickness
CT2802 289mm 511mm 55mm 15-50mm.
CT6552S
(Cooktop) 578mm 511mm 45mm
(Controls) 88mm 511mm 63mm
BICT600 578mm 511mm 45mm
20mm
CT6552S Control Box Installation
· Remove the brackets from the cooktop and the box.
· Place the cooktop in the cutout.
· Feed the cooktop wiring harness up through the box cutout.
· Remove Control Box cover.
· Connect the cooktop wiring harness.
· Clamp the wiring harness.
· Wire the mains to the box and clamp.
· Replace Control box cover.
· Roll the box into the cutout.
· Secure control box and cooktop using brackets provided.
Note: Two small brackets are provided that screw to the sides of the control box. These
must be used to clamp the control box down to the joinery. Three brackets are
provided for clamping down the cooktop.
Part No. 599049B September 2000
min.
50mm
Loading...