Page 1
INSTALLATION GUIDE
COMPANION OVENS
ACCESSORY 0”/76CM TRIM KIT
Keep this document handy for easy reference.
●
This Trim Kit is designed to complement your companion product if installing into 30” (760mm) wide cabinetry.
●
For contact information or if you require service, assistance or replacement parts, see your ‘Service & warranty’ booklet.
This Trim Kit is designed to be installed ONLY with the following FISHER & PAYKEL products:
- Companion Ovens
- or in combination with OB30/OB76 Ovens
2 PARTS SUPPLIED
US CA NZ AU
PROUD INSTALL
min. 22 1/16” (560mm)
1 CABINETRY SPECIFICATION
Trim Surround dimensions
29 13/16” (757mm)
Trim Surround (1)
1 5/8” (42mm)
Product Support
Brackets (2)
(for supporting your
companion product)
Phillips
5⁄8” (16mm)
screws (8)
(to secure
the Product
Phillips
1 3/4” (45mm)
screws (4)
(to secure the
Trim Surround)
Phillips
2” (50mm)
screws (2)
(to secure the
Oven)
Support
Brackets)
18 13/16”
(478mm)
3 POSITION TRIM SURROUND ON CABINETRY
Line up the cut “V” with your cavity center mark
Center line mark
PROUD INSTALL
FLUSH (INSET) INSTALL
20 7/8” (530mm)
FLUSH (INSET) INSTALL INSTALLATION
1 5/8” (42mm)
WITH OB30/OB76
IMPORTANT!
●
Ensure all packaging and protective film
is removed from the Trim Surround before
installing.
1/2” (12mm)
Dividing
**
min.
18 1/2”
(470mm)
**
18 7/8”
(480mm)
Hard wood
shelf is
required
*
**
1 Mark the center of your cavity at the front.
2 Mount the Trim Surround with the small lip
resting flat on the front edge of the cabinetry
shelf.
min. 22 1/16” (560mm)
Cutout to allow
for Ventilation
1 15/16” (50mm)
Refer to separate
Product Install
Guide
min. 22 1/16” (560mm)
min. 29 15/16” (761mm)
23 5/8” (600mm)
Cutout to allow
for Ventilation
1 15/16” (50mm)
Refer to separate
Product Install
Guide
3 Center the Trim Surround by lining up the
small cut “V” in the lip with your center mark
from Step 1.
Front edge of cavity
Note: If installing above an Oven, ensure both
products are centered and aligned in the
cabinetry.
Trim Surround
18 13/16”
(478mm)
PROUD INSTALL
1 5/8” (42mm)
*
Cavity side walls must be
strong and structurally
supportive
●
to secure Trim Surround
●
to secure oven to
Note: Cavity Depth is
dependant on products used.
18 7/8”
(480mm)
FLUSH (INSET) INSTALL
18 1/2”
(470mm)
INSTALLATION
WITH OB30/OB76
22 1/16” (560mm)
1/2” (12mm)
dividing shelf
is required
Proud = 22 5/8” (575)
Flush = 24 3/16” (614)
Center line mark
Front edge of cavity
C
L
continued >
Page 2
4 SCREW THE TRIM SURROUND ONTO THE CABINETRY
Using the 4 supplied screws, secure the Trim
Surround to the cabinetry in the correct hole
positions, as shown.
Pre-drill as necessary to avoid splitting the
wood.
IMPORTANT!
Do not screw through either center holes in
the Trim Surround.
6 INSTALL YOUR OVEN (REFER TO SEPARATE INSTRUCTIONS SUPPLIED WITH OVEN)
Ensure you use the supplied
plastic screw grommets,
so that the oven is secured
correctly.
5 SECURE THE TWO SUPPORT BRACKETS IN THE CAVITY
1 Position left and right support
brackets as shown inside, against
the walls of the cavity.
We recommend butting the
brackets up against the rear
frame of the Trim Surround.
2 Secure through front and rear
hole locations on both brackets
using the screws supplied.
Secure the Trim Surround using the
screw hole locations shown
1 Install your oven as per the oven installation
instructions.
2 Ensure the oven and Trim Kit are correctly aligned
and the oven door can open and close freely, before
securing.
3 Using the 2 supplied Phillips 2” (50mm) screws,
secure through the inner frame of the oven and then
through the two upper hole locations on either side
of the Trim Surround, as shown.
Support
Bracket
591792A 10.18
Loading...