Fisher & Paykel 790LH Install manual

INSTALLATION INSTRUCTIONS

Refrigerator Surround Kit

E402B, RF402B, E442B, RF442B, E522B, RF522B, RF522W, RF522A, RF540A and RF610A models

NZ AU GB AE HK SG IE EU CN IN

IMPORTANT!

SAVE THESE INSTRUCTIONS

The models shown in this document may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.

3 BEFORE INSTALLATION

All dimensions are internal or cavity dimensions. The refrigerator can be installed:

In a cavity with 16mm panel (bottom trim attached), or in a cavity where the product

is at floor level (no bottom trim). (Diagram 1a).

In a cavity with a toe kick under the product with the bottom trim fitted to the base

(Diagram 1b).

Check whether your fridge has hinges concealed by the front of the fridge door.

For refrigerators / freezers where the hinge is not concealed by the door refer to spare parts for the correct kit number. 820413 D should list non concealed number kit.

Concealed hinge Non concealed hinge

1 REFRIGERATOR SURROUND KIT

This kit is designed to be used with models with a refrigerator height of between: 1695 – 1806mm with curved or flat door styling. You can find the part number for each installation in Section 2.

To give the most integrated look, the kitchen cabinetry should be flush with the front of the refrigerator door.

Tools required (not included)



No. 2 drill bit – long.



Electric drill.



Phillips screwdriver.



1 x 16mm piece of MDF the same size as the base of the cavity (optional). Not needed if refrigerator is sitting directly on the floor and not on raised toe kickarea.



Joiner kit (part number 819264) required if joining two refrigerators side by side.

2 KIT PART NUMBERS AND CAVITY DIMENSIONS TABLE

Diagram 1

4 GETTING STARTED

Check that the internal cabinetry dimensions are correct (see Diagram 1a/b).

Unpack the refrigerator as per instructions on carton.

IMPORTANT!



Due to the size of the refrigerator(s), it is essential that assembly of the surround kit be undertaken with a minimum of two ablebodied persons.



It is important to include adequate venting to the top of the refrigerator, to ensure efficient operation.



The installation of the refrigerator(s) can be at floor level as shown in Diagram 1a or installed above the toe kick board as in Diagram1b.



Rollers and feet must be fitted.



Refrigerators installed above the toe kit should have a floor base constructed to support the total weight of the loaded refrigerator(s) placed on it.

The placement of the 16mm MDF or plywood under the refrigerator(s) on either installation type is to allow the fitment of the bottom trim that covers it. It is optional.

Diagram 1a Refrigerator at floorlevel

REFRIGERATOR MODEL

Diagram 1b Refrigerator above toekick

E402B

RF402B

1 X E402B

1 X RF402B

E402B

RF402B

E402B

RF402B

2 X E402B

2 X RF402B

E442B

RF442B

1 X E442B

1 X RF442B

E442B

RF442B

2 X E442B

2 X RF442B

E442B

RF442B

E522B

RF522B

RF522W

1 X E522B

1 X RF522B

1 X RF522W

E522B

RF522B

RF522W

2 X E522B

2 X RF522B

2 X RF522W

E522B

RF522B

RF522W

RF522A

1 X RF522A

(French door model)

RF540A

RF610A

1 X RF540A

1 X RF610A

(French door model)

CAVITY DIMENSIONS (Flush to edge of door) mm mm mm mm mm mm mm mm

Width

Depth*

C 1

Height**

C 2

Height***

Air vent depth

Air vent width

807 1467 852 1557 962 1777 962 1072

700 700 700 700 700 700 700 700

1790 1790 1790 1790 1790 1790 1790 1875

1806 1806 1806 1806 1806 1806 1806 1891

200 200 200 200 200 200 200 200

502 1162 547 1252 657 1472 657 767

KIT PART NUMBERS LH RH LH RH LH RH

Brushed Stainless 24371 24372 24373 243 74 24375 24376 24377 24378 24379 24381 24380

Plus Joiner Kit 819264 819264 819264

* Depth is a minimum requirement.

** Height is without 16mm MDF packer.

*** Height is with 16mm MDF packer.

Cavity dimensions above are to be used as minimum dimensions.

continued >

5 PARTS SUPPLIED

Top trim (1)

8 SECURE FLOOR STOPS

Two floor stops are supplied to prevent the refrigerator from being pushed too far back into the cavity. These are mounted on the base or floor at a distance of 688mm from the face front edge of the trim kit.

Floor stops Part number: 460912 (2)

Side trim (2)

Bottom trim (1)

Side trim brackets (10)

Top trim brackets:

– Single refrigerator kits

(2 brackets)

– Side by Side kits

(3 brackets)

Side trim brackets (4)

6 SECURE TOP TRIMBRACKETS

Side trim centre brackets (6)

Screw type A: #8 x 12 Pozi Drive CSK (26)

Washers 4 x 11 x 1mm (2)

Long screws 10 x 75 CSK PH Part number: SP0207 (2)

TRIM INSTALLATION

The bottom trim is designed to cover the front edge of the floor base panel of the refrigerator. This trim can be installed on a raised toe kick (Diagram 1a) or toe kick below the refrigerator (Diagram 1b)

Remembering that if this trim is to be used with the refrigerator at floor level the cavity dimensions will need to have 16mm added to its height to allow for the bottom trim to be fitted. Note this trim is optional on this type ofinstallation. If used with a raised toe kick the 16mm packer should be part of the base (Diagram5). Therefore 16mm is not required to be added to the height dimension.

If used place the 16mm piece of plywood or with bottom trim fitted into the cavity

(Diagram 5 or 6). Note: the piece should be the same size as the base of the cavity.

Remove protective coating film from surround trim.

To install the surrounds, first clip in the top surround. Ensure the locator strips at the

rear of the top brackets clip into the rear of the top trim.

Clip both side trims into place starting from the front refrigerator edge.

!0 MOVE INTO CAVITY

150mm

688mm

Diagram 4

16mm plywood or MDF board insert

Part of base

Diagram 5



Locate the two/three top trimbrackets.



For the side by side refrigerator kits, one bracket is to be screwed in the top centre of the cabinetry, secure the top bracket with two of the screws (Type A, #8 x 12 PoziDrive CSK) (see Diagram 2a).



For all other kits, the two brackets are to be secured on either side, by two screws which are mounted from the side (seeDiagram 2b).



Looking at the front of the refrigerator, place the top brackets on top of the woodencabinetry.



Care must be taken to line up the top front edge of the brackets with the leading edge of the cabinetry.

Hint: holes should be drilled in the centre of the slot in the brackets to allow for adjustment.

7 SECURE SIDE TRIMBRACKETS



Locate the ten side trim brackets.



Position five brackets to the left hand side of the cabinetry and the remaining five brackets to the right hand side of the cabinetry.



Brackets should be evenly spaced down each side (see Diagram 3a/b). Secure each of these brackets with the two screws provided.



Care must be taken to line up the front edge of the brackets with the leading edges of thecabinetry.

Diagram 2a Centre bracket

Diagram 2

Diagram 2b End bracket

Diagram 3bDiagram 3a

If installing two refrigerators/freezers side by side a joiner kit is required. Refer to these instructions and fit joiner kit before pushing refrigerator into place, see Diagram 6.

Plug refrigerator into electrical socket, run water connection to

refrigerator if required (Ice & Water models only).

Gently install refrigerator into cabinetry making sure it is

Optional

centred within the surround trim.

The front of the refrigerator door should be flush with the front

of the cabinetry to obtain anintegratedlook.

Ensure the front levelling feet are adjusted to take the load of

the fridge and keep it in place.

Diagram 6

!1 FURTHER INFORMATION

Before you call for service or assistance ...

Check the things you can do yourself. Refer to the Installation Instructions and your User Guide. Checkthat:

Your product is correctly installed.

You are familiar with its normal operation.

You have read the ‘Troubleshooting’ section at the back of the User Guide.

If after checking these points you still need assistance or parts, please contact your Fisher & Paykel trained and supported service technician, Customer Care Centre, or contact us through our website www.fisherpaykel.com

844144 B 05.16